HF_1004_Asbestos_Testing_Results.pdf

Asbestos Science Technologies, Inc.

P.O. Box 505

Bangor, Ca. 95914

530-518-0934 email - astinc17@yahoo.com

Site Inspected: Residence #1004 in Hayfork, Ca.

Date Of Inspection: May 2, 2014

A visual inspection was conducted of the above residence known as #1004 in Hayfork, Ca. on May 2, 2014 by Laurie Warren - Certified Site Surveillance Technician (C.S.S.T. #

12-4934) The inspection of the building was conducted in accordance with EPA AHERA standards.

All suspect material was touched and sampled to determine asbestos content as well as friability.

All homogeneous areas of friable and non-friable ACM were identified. This inspection was conducted in accordance with EPA, CAL/OSHA and local regulatory guidelines. Sample results are attached. Samples were sent to Schneider Laboratories in Richmond, Virginia for analysis.

Asbestos content shall be determined using the method specified in Appendix A, Subpart F, 40

CFR Part 763, Section 1, Polarized Light Microscopy. If the asbestos content is less than 10%, verification shall be made using the point counting method specified in Appendix A, Subpart F, 40

CFR Part 763, Section 1,7,2,4 Polarized Light Microscopy, Quantification of Asbestos Content.

There were two positive samples for asbestos in this residence #1004.

Sample #9 was taken of the bedroom by the bathroom closet flooring. There are two layers of asbestos containing material in this closet area.

Sample #12 was taken of the linoleum flooring in the bathroom. It is unknown which layer of linoleum is asbestos containing and as such, all layers in the bathroom shall be considered asbestos containing.

Exterior surfaces were not sampled as part of this inspection.

Only a Department of Occupational Safety and Health Administration certified asbestos abatement contractor shall be allowed to perform this work. Clearance sampling shall be performed on any modernization project in this unit involving the removal of asbestos.

This report was prepared by Floyd E. Warren Certified Asbestos Consultant - C.A.C. #09-4590

Floyd Warren

SCHNEIDER LABORATORIES GLOBAL

I N C O R P O R A T E D

2512 W. Cary Street • Richmond, Virginia • 23220-5117

804-353-6778 • 800-785-LABS (5227) • (FAX) 804-359-1475

Over 25 Years of Excellence in Service and Technology

LABORATORY ANALYSIS REPORT

Asbestos Identification by EPA Method¹ 600/R-93/116; EPA 600/M4-82-020

CUSTOMER: Asbestos Science Technologies, Inc

ADDRESS: 191 Hazel Street

Gridley, CA 95948

ACCOUNT #: 4038-14-785

PROJECT NAME: Residence 1004

PO NO.:

JOB LOCATION: Hayfork CA

PROJECT NO.:

DATE RECEIVED: 5/6/2014

DATE ANALYZED: 5/6/2014

DATE COLLECTED: 5/2/2014

DATE REPORTED: 5/6/2014

SampleType: BULK

PLM Analysis Results

Asbestos Fibers Other Materials

Sample

Layer ID

Identification/

Customer SLI Sample

No.

Sample/

Layer Name

1 32207028 Kitchen Floor

Beige, Org.Bound/Fibrous

None DetectedLayer 1: Linoleum

Sample was inhomogenous, subsamples of each component were analyzed separately.

CELLULOSE FIBER35%

MINERAL/GLASS WOOL15%

NON FIBROUS MATERIAL50%

Tan, Soft

None DetectedLayer 2: Mastic NON FIBROUS MATERIAL100%

2 32207029 Kitchen Floor

Tan, Soft

None DetectedLayer 1: Mastic NON FIBROUS MATERIAL100%

3 32207030 Dining Area

White, Powdery

None DetectedLayer 1: Sheetrock CELLULOSE FIBER2%

NON FIBROUS MATERIAL98%

4 32207031 Dining Area

White, Granular

None DetectedLayer 1: Joint Compound NON FIBROUS MATERIAL100%

Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory.

Total Number of Pages in Report: 3

Results relate only to samples as received by the laboratory. Visit www.slabinc.com for current certifications.

Accrediting bodies: AIHA-LAP, LLC 100527, NVLAP 101150-0, VELAP/NELAC 460135 - Call laboratory for current national and state certifications.

PLM Analysis Results

Asbestos Fibers Other Materials

Sample

Layer ID

Identification/

Account - Workorder 4038-14-785 (Continued) Page 2 (Continued)

Customer SLI Sample

No.

Sample/

Layer Name

5 32207032 Fireplace

Gray, Hard

None DetectedLayer 1: Mortar NON FIBROUS MATERIAL100%

6 32207033 Kitchen Floor

Beige, Org.Bound/Fibrous

None DetectedLayer 1: Linoleum

Sample was inhomogenous, subsamples of each component were analyzed separately.

CELLULOSE FIBER35%

MINERAL/GLASS WOOL15%

NON FIBROUS MATERIAL50%

Tan, Soft

None DetectedLayer 2: Mastic NON FIBROUS MATERIAL100%

7 32207034 Bedroom Across From Kitchen

White, Granular

None DetectedLayer 1: Joint Compound NON FIBROUS MATERIAL100%

8 32207035 Bedroom Across From Kitchen

White, Powdery

None DetectedLayer 1: Sheetrock CELLULOSE FIBER4%

NON FIBROUS MATERIAL96%

White, Granular

None DetectedLayer 2: Joint Compound NON FIBROUS MATERIAL100%

9 32207036 Bedroom By Bath

Beige, Org.Bound/Fibrous

Layer 1: Linoleum

Sample was inhomogenous, subsamples of each component were analyzed separately.

CHRYSOTILE20% CELLULOSE FIBER20%

MINERAL/GLASS WOOL10%

NON FIBROUS MATERIAL50%

Tan, Soft

None DetectedLayer 2: Mastic NON FIBROUS MATERIAL100%

10 32207037 Bedroom By Bath

White, Granular

None DetectedLayer 1: Joint Compound NON FIBROUS MATERIAL100%

Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory.

Total Number of Pages in Report: 3

Results relate only to samples as received by the laboratory. Visit www.slabinc.com for current certifications.

Accrediting bodies: AIHA-LAP, LLC 100527, NVLAP 101150-0, VELAP/NELAC 460135 - Call laboratory for current national and state certifications.

PLM Analysis Results

Asbestos Fibers Other Materials

Sample

Layer ID

Identification/

Account - Workorder 4038-14-785 (Continued) Page 3 (Continued)

Customer SLI Sample

No.

Sample/

Layer Name

11 32207038 Bedroom By Bath

White, Powdery

None DetectedLayer 1: Sheetrock CELLULOSE FIBER3%

NON FIBROUS MATERIAL97%

12 32207039 Bathroom

Beige/Brown, Org.Bound/Fibrous

Layer 1: Linoleum

Sample was inhomogenous, subsamples of each component were analyzed separately.

CHRYSOTILE20% CELLULOSE FIBER20%

MINERAL/GLASS WOOL10%

NON FIBROUS MATERIAL50%

Tan, Brittle

None DetectedLayer 2: Mastic NON FIBROUS MATERIAL100%

Beige, Org.Bound/Fibrous

None DetectedLayer 3: Linoleum

Sample was inhomogenous, subsamples of each component were analyzed separately.

CELLULOSE FIBER35%

MINERAL/GLASS WOOL15%

NON FIBROUS MATERIAL50%

Tan, Brittle

None DetectedLayer 4: Mastic NON FIBROUS MATERIAL100%

Method reporting limit is 1%. PLM analysis is based on Visual Estimation and NESHAP recommends that any asbestos content less than 10 percent be verified by PLM Point Count or TEM Analysis. This report must not be reproduced except in full with the approval of the laboratory.

Total Number of Pages in Report: 3

Analyst: MOHAMMED B. HASHIM

Results relate only to samples as received by the laboratory. Visit www.slabinc.com for current certifications.

Reviewed By: Johnathan Wilson, Analyst

Accrediting bodies: AIHA-LAP, LLC 100527, NVLAP 101150-0, VELAP/NELAC 460135 - Call laboratory for current national and state certifications.