Unmarked_Truck_Specifications.DOCX

Un-Marked LE TRUCKS SECURE-IDLE SYSTEM Install secure idle switch manufactured by Secure-Idle Inc., www.secure idle.com, (phone: 309-475-2286). Agent should be able to put the vehicle in "Park", push the button on the Secure-Idle System on the dashboard accessible from the driver's seat (position button on dash board to the left of the steering column), turn the ignition off and remove the key while the vehicle's engine keeps running. Engine should stop running if someone attempts to drive vehicle without the ignition key. To deactivate, insert the key and turn the ignition to the "on" position.

HANDHELD SIREN/LIGHT CONTROL PA Whelen 100 watt HHS2200 H-2 Handheld siren with full light controls, 12 push buttons. Microphone control head and switch will be installed outside of the center console. Driver’s side with the standard metal mic clip. All other components will be concealed out of sight in a Premier, Under Armrest Insert, 8 7/8” X 9 1/2 “ , with components facing the driver for easy access but not inside the console compartment. Unit will be capable of operating the siren controls, emergency lights and PA system. Park Kill feature will be enabled to deactivate the siren when the vehicle is shifted into park. Horn Ring feature will be enabled to change audible siren sound via the horn's ring. PTT push to talk PA system operated by remote handhold siren/light control will be wired for operation through siren speaker when the microphone button is depressed. This will override siren tone. Brake light kill switch to be installed/activated and operated as one of the accessory features on the handheld siren/light control.

Siren to be operated independently of level 3 by user. User will be able to activate "Hi-Lo, Wail. or Yelp" as needed on the handheld siren control.

NOTE: Lights are to be switched as follows on handheld siren/light control keypad: Level 1 - rear lights OLNY, Level 2- front and rear lights without wig wags, Level 3 - front lights, rear lights, wig wags and siren.

Run an extra remote USB cable inside the center console for trouble shooting.

POWER OUTLETS A 3 port 12-volt DC outlet with 2 USB power outlets will be installed on the passenger side of the Console with the outlets facing upward. A 3 way 12-volt DC with USB power outlets will be installed on the passenger side of the center console as far forward as practical or at the rear face of the console with the outlets facing upward. One additional 3- way 12 volt DC with USB power outlet will be installed in the rear of the vehicle in the cargo compartment in a location accessible to the user.

POWER INVERTER A THOR 750W a minimum 600 watts with 120 VOLT and duel 120 VOLT flush mount receptacles and USB power; or comparable. Will be mounted out of sight underneath the rear seat. It will be positioned so that outlets and power switch are accessible. A dual 120 volt flush mount receptacle will be connected to the inverter and installed as to be accessible from the front driver’s seat preferably on the side of the console between the driver’s seat and dash.

WIRING: 2nd Generation Patrol Power Company, part number PPGEN2 with brackets. Wiring harness with adjustable power timer, will be specific to vehicle being installed (Avail Ford, Dodge, Chevy). http://www.patrol-power.com. Minimum 2 circuits 8 gauge wiring. This set up will eliminate the need for a master switch.

This set up will eliminate the need for a master switch. The timer will be set to 1 hr.

Rechargeable LED flashlight INOVA TR4 lithium ion powered rechargeable LED flashlight.

FIRE EXTINGUISHER Amerex Part# ASCOT; 5 pound UL rating 3A40Bc multipurpose dry chemical fire extinguisher. Do not mount fire extinguisher.

LOCK BOX FOR BED OF TRUCK ALL WEATHER Tuffy Security Products Part #257 this box needs to be designed for the outdoor use, extremely weather resistant and lockable drawers. Combo/key lock. Box needs to be sated at 2000 lbs. on top. Durable powder coat finish color Black. 2 drawers 50/30 split.

Or another option would be:

ENCLOSED FIBERGLASS CANOPY With locking rear access window. Color will match the truck.

WIRELESS CELLULAR AMPLIFIER; install Wilson Electronics wireless Dual Band Amplifier, part number 801201 The kit includes amplifier and low profile interior antenna. The amplifier and all wiring shall be concealed. The kit should be powered through the vehicle ignition. Install a universal size cradle designed for smart phone with the interior antenna built in to the cradle. (Eg. Wilson Electronics Sleek 4G cradle. Model #460107 the cradle will be mounted on the dash within reach and view of the driver. Install the Low Profile Antenna at least eight inches from where the cell phone or cellular data card will be used. A low profile roof antenna will be centered in the roof of the cab and will be a type similar to the AP Cell/LTE/WiFi by Antenna Plus Address: WeBoost 3301 East Deseret Dr St. George, UT 84790 tel 435.986.6212 | fax 435.656.2432 sunruh@weboost.com www.weboost.com

Mobile Radio Wire Harness customized installation of Forest Service radio. Radio model will be provided by the FS. When radio is provided install FS radio in center console, when radio is not provided proper wiring and connections will be installed by contractor wire HOT to vehicle battery. 3 coax cables will be ran for radio antennas w/rain caps.

UNDERCO Band Antenna Part# STl-CO model MMAS-BSSF-VHF: roof mounted, plug and play antenna whip. Base and antenna are one piece and look similar to stock vehicle antenna systems. The UHF antenna, if needed, will be installed with a separate antenna system – window glass mounted antenna.

Window Tint all windows will be tinted to FS specifications and a final decision will be made by an FS representative when vehicles arrive from factory

Two LED X Exterior Lights - by SoundOff Ghost Light, part #EGHST1*) One mounted in the front grill of vehicle on driver's side and one mounted in the front grill on the passenger side. Lights should be concealed so that they are not visible until activate from inside or outside the vehicle. Light colors will be red on driver’s side and blue on the passenger’s side.

Two LED Interior Lights - by SoundOff Ghost Light, part #EGHST3*) Mounted in the upper portion of the rear window as applicable or if vehicle is outfitted with a canopy then installed in upper, center of rear window. Light colors will be red on driver’s side and blue on the passenger’s side. Installed with a Mercury switch to turn lights off and on when Lid is lifted and shut. As needed.

WIG· WAG AND HIDE·AWAY CORNER LED LIGHTS Front light assembly Install Two (2) SoundOff Part# ELUC2S025R (red) and two (2) SoundOff Part# ELUC2S025B (blue) LED With a 25' cable for headlight assembly. One (1) red and one (1) blue, 9 LED Hideaways Code 3 Part# HB915R I HB915B mounted in each of the front clear headlight assemblies (one red and one blue of each side of vehicle). Install Code 3 Headlight Flasher model "Wig-Wag 700. Install Whelen Headlight Flasher model # ULF44 Flasher to create the "Wig-Wag function. Wig Wags should be installed with high beam override and switched to operate on Level 3 only button on the remote handheld siren/light control. If the vehicle will not accept inserts or the Wig – Wag function in the head light / High beam Light assembly use Nforce ENFSGS3RW AND ENFSGS312BW 12 LED Dual Color along with, Flasher model # ULF44, Mounted in the grill. “Red/White in the center of the grill on the Driver’s side and Blue/White in the center of the grill on the Passenger side, to create a Wig Wag with a solid burn option for Take downs or Scene lighting.

Rear light assembly: Install Two (2) SoundOff Part# ELUC2S025W (White) for tail lights mount one in each of the top red lenses of the assembly on each side of vehicle) and two (2) SoundOff Part# ELUC2S025B (blue) LED With a 25' cable for tail lights mounted in the white lens backup lights in the rear light assembly on each side of vehicle. All should have variable flash pattern.

100 WATT SPEAKER SoundOff # ETSS100L 100 watt speaker with bracket included. Speaker will be mounted underneath the hood in the front portion of the engine compartment out of sight and protected from dirt/mud. Police radio will be wired to allow radio broadcast to be received from speaker at agent's option. PA system operated by remote handheld siren/light control will be wired for operation through siren speaker.

WINDSHIELD LIGHT Whelen, Dual Avenger, with Takedown (Red/Blue) #01-066F854-52. Light will be hard wire and mounted (not powered by "cigarette lighter") on the passenger side of the front visor with included Velcro straps. Wiring will be routed through A· frame molding for concealment and quick release connection will be installed to allow the light to be removed at agent's discretion.

PATROL POWER MINI UNIVERSAL POWER DISTRIBUTION CENTER (04-0208) Provides connections to all emergency warning/lighting system, radio communication, and auxiliary electrical components. The timer will be set to 1hr.

OVERHEAD RIFLE RACK An overhead rifle rack will be mounted above and just behind the first row of seats using the handles provided by the manufacturer just above the second row doors. If the mount will not work then the Forest Service Rep will let the vendor know where to mount the rifle. The Big Sky rack “UCB slider” mounting system will replace the handles and utilize the same bolts and roofline anchored threads that retained the handles. The Big Sky rack “UCB” is telescoping in design and will extend horizontally through the cab. It is adjustable on the mounting plates to allow the installer to place the bar and rifle rack as high into the headliner as practicable and forward just behind the first row of seats for quick access by the driver.

The patrol carbine rifle (AR15-A2) will be mounted to UCB using the Santa Cruz model SC-934-5-A Rapid adjust universal overhead gun rack. The lock (SC-5-XL) will be keyed with the SCA #2 key.

The following components come with the SC-934-5-A as a kit: SC-5XL universal gun lock; SC-503 24” flat bar; SC-1901 AR butt plate; SC-9903 L-bracket; SC-932 Rollo bar mounting bases; SC-9906 U-bolts; associated nuts and bolts; and installation instructions.

A ten (10) second timer Big Sky model RC-15-AL, or equivalent with push button release (FS representative will specify location) will activate the lock for removal of rifle. The button will be a momentary push button switch, also available from Big Sky racks.

The below illustration (from the Santa Cruz website) shows a typical installation – the USFS unmarked vehicle mounting will be to the overhead bar not a prisoner cage.

image1.png