A06_Trailer_Specifications_2022.pdf

Specifications

Remote Sensing Fire Weather Support Unit (RSFWSU) Field

Section Trailer

Description: Cargo trailer will be used for the conduct of RAWS field operations and to ensure compatibility with existing support equipment and procedures.

The Bureau of Land Management has a requirement for one (1) dual-axle (tandem) deck over cargo trailers with a cargo box that is approximately 20 feet long and approximately 8.5 feet wide. The cargo box shall have a wedge or V nose that is approximately 2 feet included as part of the overall length of 20 feet.

Submissions will be evaluated to determine the best value to the government based on the technical merits of the offering, delivery date, warranty, and cost also being a factor. Submission packets should contain the manufacture make and model, and include a specification list that addresses the specification requirements contained in this document.

Delivery destination is:

Bureau of Land Management

RSFWSU

3833 S. Development Ave Boise, ID 83705

The trailer shall meet the following specifications:

Dimensions

Trailer design is a “deck over” enclosed cargo trailer. The deck over is required due to increased trailer ground clearance and no interior wheel well.

The overall length of the trailer shall not exceed 24 feet 6 inches. The overall width measured at the widest point (outside of fenders) shall not exceed 8 feet 6inches.

The trailer shall have a GVWR of 9700 pounds minimum.

The interior dimensions of the cargo area shall have a usable length of 19 feet 8 inches plus or minus 2 inches. The usable width shall be 7 feet 6 inches plus or minus 2 inches. The interior height shall be 6 feet 10 inches, plus or minus 1 inch.

Construction

The trailer shall have two doors; one 36-inch (minimum) side entry door located in front of the axles on the passenger side, and one rear swing down ramp. Side entry door will be equipped with a deadbolt, pull out step and grab handle. Rear ramp door shall be secured with a double rear bar lock style system and be load rated at a minimum of 4500 lbs. Models with a front swing down door ramp are not required but will be accepted for bid.

Trailer shall be constructed with steel frame with uprights on minimum 16-inch center spacing.

The rear of the trailer shall have a beavertail of 48 inches plus or minus 6 inches.

The trailer frame shall be black and undercoated for rust protection.

The rear door opening shall have a width of 85 inches plus or minus 2 inches and a minimum height of 75 inches.

The rear ramp shall be with cable assist to help with lowering and raising the door.

The trailer shall be equipped torsion style suspension and axles rated at a minimum of 12,000 pounds.

The trailer interior shall have welded recessed E-Tracks on both side walls and front located at 12”, 28” and 42” high on center measured from floor.

The trailer shall have twelve (12) 6,000lb rated Recessed Swivel D rings welded to the frame placed at locations to customer specifications.

The trailer shall have a total of five identical tires and wheels (including spare). The tires shall be load range E. The wheel well shall be reinforced to prevent damage from tire blowouts.

Trailer shall be equipped with four-wheel electric brakes with battery backup for breakaway protection.

The trailer shall be equipped with a 2-5/16 locking up ball coupler.

The trailer shall be equipped with a tongue mounted electric jack with manual override and with ground pad rated for the trailer size.

The rear of trailer shall have two (1 each corner) stabilizer jacks rear. The jacks must reach the ground when trailer is sitting on level ground.

The trailer shall be constructed with aluminum exterior skin with a minimum thickness of 0.030 inches and a maximum of 0.040 inches. The skin shall be painted/coated white in color.

The front of the trailer shall have aluminum tread or diamond plate applied to the lower 24 inches minimum, and 8 inches minimum applied to the lower sides of the trailer shell to protect against rock chips.

The interior shall be finished with white vinyl or similar type paneling.

The floor shall be made of ¾ inch High Density Polyethylene (HDPE) or similar type flooring with on-slip surface.

The interior shall include a bracket to securely mount the spare tire to the wall.

The trailer shall have 2 roof vents, 1 with 12-volt electric vent fan.

Electrical

Trailer shall be wired with a 7-way 12-volt vehicle connector.

Trailer lighting shall meet DOT requirements. All lighting for the trailer shall be LED.

Trailer shall include a 12-volt RV style deep cycle battery

Trailer shall have a minimum of 6 interior 12-volt LED dome lights controlled by switches (2) located near the rear and side entry doors.

Warranty Requirements

The trailer shall have a minimum one year warranty from date of acceptance that covers the trailer and all components it is built with.

The trailer shall carry a minimum three year warranty that covers a minimum of the trailer frame, body structure and exterior body skin.