A06_Specifications.pdf

Attachment 1. Specification Requirements 4/13/2023

EQUIPMENT SPECIFICATIONS

1. Backhoe Loader Specifications.

a. Standards: The Backhoe Loader must comply with the current SAE, ASME, ANSI, ISO, AEM, EPA emission standards and any other applicable federal standards.

b. Machine Specifications (The backhoe loader shall meet or exceed these specifications): Case 580N EP, or approved equal, with the following standard features and options:

i. All equipment and attachments shall be new.

ii. Operating weight: 14,000-18,000lbs.

iii. Engine:four cycle diesel with a minimum net rating of 68 horsepower

(ISO9249).

1. Shall meet US EPA Tier 4 Interim Stage IIIB emissions.

2. Maximum RPM at rated power: 2200 rpm.

3. Heavy Duty High Efficiency Air Filter.

iv. Maximum overall transport width: 7’-6”.

v. Maximum overall transport height: 12’-0”

vi. Maximum overall transport legnth with loader bucket on the ground:

24’-0”

vii. Equip the engine with a cold weather starting kit.

viii. Diesel Fuel tank: Of sufficient capacity to operate the machine under heavy digging conditions for a period of 12 hours without the need for refueling.

1. Minimum capacity 30 gallons.

ix. Machine shall have travel alarm.

x. Tires: Front: 12-16.5 NHS (10 ply) 1-3; Rear: 19.5L-24 (10 ply) R4

ATU or approved equal.

xi. Equip machine with a battery disconnect switch.

xii. The backhoe loader shall be four wheel drive with differential lock and Auto shift transmision.

xiii. Lighting:

1. Shall include all turn signal, break lights and hazard lights.

2. Working lights minimum 4 front and 4 rear and a one per side

3. All work lights are LED.

xiv. Equip backhoe loader with necessary front counterweights as requred for backhoe with a standard backhoe.

xv. Equip backhoe loader with necessary stablizers with street shoes and rock guards as required for its size and lifting capacity.

xvi. The boom arm and dipper stick combined shall be sized to meet the following requirments:

1. Maximum horizontal reach from swing pivot at ground line:

Minimum 17’-10”.

2. Maximum digging depth (SAE): minimum 13’-6”.

3. Maximum loading height: minimum 11’-5”.

4. Equip the boom arm and dipper stick with auxiliary hydraulic lines with quick connectors for use with attachments such as, but not limited to, breaking hammer, plate compactor, brush hog.

5. Equip backhoe with pin-on bucket, with a lifting eye intergrated into the bucket. The lifting eye shall have a working load limit greater then or equial to the maximum lifting capacity of the backhoe at any distance from the backhoe.

6. Bucket digging force(ISO): Minimum 10,700 lb.

7. Stick Digging Force(ISO): Minimum 6,800 lb.

8. Lifting Capacity:

a. Minimum 2,850 lbs over end at maximum groundline reach.

xvii. The front loader on the backhoe shall be meet the following requirements:

1. Equiped front loader with direct pin links

a. Loader bucket shall have 3 intrograde lifting eyes in the top outside of the bucket one in the center and one on each end of the bucket.

2. Lift Capacity to full height: 6,150 lbs

3. Dump clearance height, bucket at 45 deg: 8’-8”

xviii. Hydraulic system:

1. Pump capacity at 2,200 rpms: 28 gpm minimum.

2. Circuit pressure operating range: 3000-4000 psi.

3. Hydraulic system capacity (including tank): 25 gal minimum.

4. Actuator for allowing boom, stick and loader bucket to be lowered to ground when engine is dead.

5. All hoses that have the potential to be damaged from vibration and abrasion will have protective covers.

xix. Backhoe hydraulic controls to be built into two joysticks or two lever backhoe controls .

xx. Front loader bucket controls shall be on a single joystick.

xxi. If the backhoe is equiped with joysticks.

1. The joysticks control pattern shall be set at SAE (Caterpillar pattern)

xxii. Provide vandal locks with 2 sets of keys for Cab door, service doors, toolbox, fuel tank cap and hydraulic tank cap. Locks do not have to be provide for the fuel tank cap and hydraulic tank cap if already locked behind a locking service door.

xxiii. Provide 2 sets of ignition keys per backhoe loader.

xxiv. Operator Cab:

1. Cab shall be certified ROPS/FOPS (ISO-3449 level 2)

a. Fully enclosed.

b. Sound be certified ANSI/SAE J1166 OCT98 is 79dB(A)

2. Cab shall have an emergency hatch exit or glass breaking safety hammer.

3. Rear view mirrors on each side of cab.

4. Equip the cab with automatic climate contol (air cond, heater, defrost), AM/FM radio, and multifunction color LCD monitor that displays all of the machine’s mornitoring systems including, but not limited to, engine hour meter, fuel level, engine temperature, hydraulicfluid temperature, and other necessary warning lights and system gages.

5. Operator seat:high back air or mechanical-suspension, fabric covered, minimum 4 way adjustment, adjustable armrest and seat belt.

6. Joystick consoles: Adjustable independently of seat.

7. Tilt stearing wheel.

xxv. Buckets and Attachments: Each bucket must be setup to work with the pin-on. Provide per each backhoe loader:

1. Rear backhoe buckets:

a. One (1) 24 inch wide heavy duty digging bucket

2. Front backhoe buckets:

a. One (1) long lip loader bucket 0.8 cu.yd. minimum capacity 80-90 inches wide with bolt on cutting edge.

xxvi. All grease points shall be fully greased per the manufacturer’s recommendations.

xxvii. The diesel fuel tank shall be filled full.

2. Operation and Service Manuals

a. The successful bidder shall deliver one (1) paper copies of the operation and service manuals for the backhoe loader.

b. The successful bidder shall deliver (by email, or on a CD or USB flash drive) one

(1) electronic copy of the operation and service manuals for the backhoe loader.