Site Drawings.pdf

UP

AREA OF

WORK

APPLICABLE CODES & DESIGN STANDARDS

CODES / REGULATIONS (LATEST EDITION UNLESS NOTED OTHERWISE):

A. Building Classification – JB Building 1

1. Occupancy Classification – JB Bldg. 1:

a. Existing Building: I-2 Institutional, Hospital (IBC), Health Care (New & Existing) (NFPA)

b. Occupancy separation:

1) Healthcare requires a 1-hour smoke barrier every 22,500sf, 200ft travel, 30sf net on each side.

2) If entire building healthcare, then:

i. Corridor wall can be smoke partition.

c. Common Path Limit: 100ft.

d. Dead End Limit: 30ft.

e. Travel Distance Limit: 200ft.

g. 8ft corridors for gurney traffic. 44” clear for remainder.

h. Doors required to be 3’0” wide minimum, with openings to be sized appropriate to accommodate room functions.

2. Construction Type:

a. Construction Type (IBC/NFPA): Type I-A/Type I (332) (Assumed based on 1922 construction).

3. Seismic Design:

a. VA H-18-8 / July 2008 / Design Category = Table 1: Critical Facility (Hospital)

1) Spectral Response Accelerations:

i. SS (VA H-18-8) – Table 3 0.596

ii. SI (VA H-18-8) – Table 3 0.171

b. IBC Seismic (Chpt. 1613):

1) Hospital with Emergency Room - Seismic Risk Category IV (Table T1604.5)

2) Seismic Design Category – Short Period (0.2-second) Response Acceleration based on IBC SDS @ 0.183g = C (1613.3.4,Table T1613.3.5(1))

3) Seismic Design Category- 1-Second Period Response Acceleration based on IBC SD01 @ 0.596g = D (1613.3.4, Table T1613.3.5(2))

c. Renovation project will require seismic design considerations for installation of new suspended acoustical ceilings and MPFE items. Campuses are located in Zone 1. Need to review with VASTLHCS Engineering for current methods use in renovations.

Approximate Project Area JB – Bldg. 1 (Abatement + Renovation) 3,600sf

CODE INFORMATION

A. Building Codes and Regulations (Latest Editions)

1. Guidance on the Technical Information Library (TIL) (http://www.cfm.va.gov/til/).

a. Master Construction Specifications, Program Guide, PG‐18‐1

b. Design and Construction Procedures, PG‐18‐3

c. Standard Details, PG‐18‐4

d. Equipment Guide List, PG‐18‐5

e. Equipment Reference Manual, PG‐18‐6

f. Design Manuals for applicable disciplines, PG-18-10

g. Design Guides for graphics, PG-18-12

h. Barrier Free Design Guide, PG-18-13 (See item A.11 below)

i. Environmental Compliance Manual, PG-18-17

j. VA Sustainable Design Guide

k. VA Directives, Design Manuals and Design Guides

1) VHA Directive 1116(2) – Sterile Processing Services (SPS)

2) VHA Directive 1761(1) – Supply Chain Management (SCM)

l. VA Design Alerts

m. VA Quality Alerts

n. VA National CAD Standard Application Guide and BIM Guide

o. VA Drawing Title Box Layout

p. VA AE Design Submission Requirements

q. VA Design Review Checklists

r. Minimum Requirements for A/E Submissions for Minor and Minor Miscellaneous projects, Handbook

H‐18‐15 Volume C

s. Office of Construction & Facilities Management Design Manual, Architectural Design Manual

t. VA Medical Center Memorandums (MCM) (request from COR)

u. Manual for Preparation and Issuance of Construction Solicitation and Contract Documents

v. Technical Summaries

w. National Codes and Standards (NFPA, NEC, Natl.

Plumbing Code, EPA, OSHA, etc.)

x. Uniform Accessibility Standards

y. Asbestos Abatement Design Manual

z. Electrical Design Manual for Hospital Project

aa. Fire Protection Design Manual

bb. Estimating Manual

cc. Seismic Requirements

dd. VA Form 10-6238 Estimate Worksheet.

2. NFPA and VA Fire Projection Manual for fire protection.

3. NFPA 101 Life Safety Code: addresses life safety and fire protection features.

a. International Building Code (IBC): Items not addressed in NFPA 101, including structural strength, seismic stability, sanitation, adequate light and ventilation, and energy conservation.

4. NFPA National Fire Codes with the exception of NFPA 5000 and NFPA 900

5. Occupational, Safety and Health Administratio (OSHA) Standards.

6. Joint Commission on Accreditation of Healthcare Organizations (JCAHO) Requirements.

7. National Electrical Code (NEC)

8. International Plumbing Code (IPC)

9. ASME Boiler and Pressure Vessel Code

10. ASME Code for Pressure Piping

11. American with Disabilities Act (ADA), Architectural Barriers Act Accessibility Standards (ABAAS) including VA supplement, Barrier Free Design Guide (PG-18-13)

12. State of Missouri Department of Health and Senior Services

13. The Provisions for Construction and Safety Signs.

Stated in the General Requirements Section 01010 of the VA Master Construction Specification.

14. Ventilation for Acceptable Indoor Air Quality - ASHRAE Standard 62.1- 2004.

15. Safety Standard for Refrigeration Systems – ASHRAE Standard 15 – 2007.

16. American Society of Heating, Refrigeration and Air-Conditioning Engineers (ASHRAE) Standard 90.1 2010, except where 90.1-2004 or 90.1-2007 are referenced or adopted by specific Veterans Affairs Design and Construction Procedures.

17. Energy Policy Act of 2005 (EPAct) and American Society of Heating, Refrigeration and Air-Conditioning Engineers (ASHRAE) Standard 90.1-2004 Appendix G.

18. Extended Industry- Standard Architecture (EISA) 2007 for new facility fossil fuel generated energy consumption reduction.

B. Authorities Having Jurisdiction:

1. VA must function as the Authority Having Jurisdiction (AHJ). VA is not subject to local imposition of code enforcement procedures.

2. Joint Commission on the Accreditation of Healthcare Organizations (JCAHO)

3. US Department of Health & Human Services (H&HS) th re e in c h e s o n e fo o t o n e a n d o n e h a lf in c h e s o n e fo o t o n e in c h o n e fo o t th re e q u a rt e rs in c h o n e fo o t o n e h a lf in c h o n e fo o t th re e e ig h th s in c h o n e fo o t o n e q u a rt e r in c h o n e fo o t o n e e ig h th in c h o n e fo o t

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

Veterans Health

Administration

VA FORM 08-6231

Drawing Title Project Title

Location

Date Checked Drawn

Project Number

Building Number

Drawing Number

CONSULTANTS:

Drawing # of

EHRM CERNER ADMIN SPACE

##-XX-###

DISCIPLINE DESIGNATORS EXAMPLES

GI = GENERAL INFORMATION

CS = CIVIL SITE

AD = ARCHITECTURAL DEMOLITION

AS = ARCHITECTURAL SITE

AE = ARCHITECTURAL ELEMENTS

GENERAL & FLOOR PLANS

AI = ARCHITECTURAL INTERIORS

AG = ARCHITECTURAL GRAPHICS

AF = ARCHITECTURAL FINISHES

AC = ARCHITECTURAL CEILING PLAN

AW = ARCHITECTURAL WAYFINDING

AP = ARCHITECTURAL SPACE PLANNING

FLOOR PLANS & SCHEDULES

AL = ARCHITECTURAL LIFE SAFETY

DRAWINGS

SF = STRUCTURAL FRAMING

MH = MECHANICAL HVAC

PL = PLUMBING FIXTURES

EL = ELECTRICAL LIGHTING

DRAWING INDEX LEGEND

U.S. DEPARTMENT OF VETERANS AFFAIRS

VA ST. LOUIS HEALTH CARE SYSTEM

VA PROJECT NUMBER: 657-21-711JB

JEFFERSON BARRACKS

EHRM CERNER ADMIN SPACE

VA Health Care System Approval:

Revision: Date:

ARCHITECT/ENGINEER:

U.S. DEPARTMENT OF VETERANS AFFAIRS

VA ST. LOUIS HEALTH CARE SYSTEM

FACILITIES & ENGINEERING SERVICE

DRAWING INDEX

JEFFERSON BARRACKS

1 JEFFERSON BARRACKS DRIVE - ST. LOUIS, MO 63125

UNITED STATES OF AMERICA

SHEET TYPE DESIGNATORS

0 = GENERAL

1 = PLANS

2 = ELEVATIONS

3 = SECTIONS

4 = LARGE-SCALE VIEWS

5 = DETAILS

6 = SCHEDULES & DIAGRAMS

7 = USER DEFINED

8 = USER DEFINED

9 = 3D REPRESENTATIONS

BUILDING NUMBER

FLOOR NUMBER ON PLAN SHEETS

SHEET NUMBER

/2

/2

:5 :1

P

M

01-G1-000

COVER SHEET

HT

CM04/22/21

657-21-711JB

CONSTRUCTION DOCUMENTS

Sheet List

Sheet Number Sheet Name

01-G1-000 COVER SHEET

01-GI-001 ICRA PLAN

01-HA-011 HAZARDOUS ABATEMENT

01-AD-100 DEMO PLANS

01-AE-100 FLOOR PLANS

01-AE-101 CEILING PLANS

01-E-100 ELECTRICAL PLAN

01-AI-100 FURNITURE & FINISHES

VICINITY MAP

PROJECT

LOCATION

TRUE

NORTH

1" = 100'-0"

KEYPLAN

PLAN

NORTH

HARD WALL

CONSTRUCTION BARRIER.

MANOMETER LOCATION

LOCK DOOR

NEGATIVE AIR

EXHAUSTED

TO EXTERIOR

CONTRACTOR

ENTRY/EXIT

ANTE ROOM

NEGATIVE AIR

EXHAUSTED

TO EXTERIOR

EXTERIOR

EXIT - 95'

ANTE ROOM

85' TO

EXIT

116'

TO

EXIT

120' TO

EXTERIOR

EXIT

th re e in c h e s o n e fo o t o n e a n d o n e h a lf in c h e s o n e fo o t o n e in c h o n e fo o t th re e q u a rt e rs in c h o n e fo o t o n e h a lf in c h o n e fo o t th re e e ig h th s in c h o n e fo o t o n e q u a rt e r in c h o n e fo o t o n e e ig h th in c h o n e fo o t

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

Veterans Health

Administration

VA FORM 08-6231

Drawing Title Project Title

Location

Date Checked Drawn

Project Number

Building Number

Drawing Number

CONSULTANTS:

Drawing # of

EHRM CERNER ADMIN SPACE

VA Health Care System Approval:

Revision: Date:

ARCHITECT/ENGINEER:

U.S. DEPARTMENT OF VETERANS AFFAIRS

VA ST. LOUIS HEALTH CARE SYSTEM

FACILITIES & ENGINEERING SERVICE

JEFFERSON BARRACKS

1 JEFFERSON BARRACKS DRIVE - ST. LOUIS, MO 63125

UNITED STATES OF AMERICA

/2

/2

:5 :1

P

M

01-GI-001

ICRA PLAN

HT

CM04/22/21

657-21-711JB

CONSTRUCTION DOCUMENTS

1/8" = 1'-0"

ICRA PLAN

1/8" = 1'-0"

LIFE SAFETY PLAN

IMG

A

IMG

B

BREAK

GW05A

OPEN WORK

GW04

CONFERENCE

GW07

CONFERENCE

ROOM

GW08

OFFICE

GW09A

OFFICE

GW09

WAITING

GW10

37' - 4 7/8"

CORRIDOR

H0011

ABATEMENT KEYNOTES/LEGEND

SCRAPE AND STABILIZE LEAD PAINTED SURFACES AT CONCRETE

DECK INSIDE GROSS REMOVAL NEGATIVE PRESSURE

CONTAINTMENT

REMOVE EXISTING ASBESTOS CONTAMINATED EXHAUST FAN,

DUCT AND HORIZONTAL SHAFT. STABILIZE EXITING FRAMING TO

REMAIN

3884 SF

SCRAPE AND STABLIZE LEAD PAINTED WALLS FROM FLOOR TO

DECK 170 LF

DEMOLISH EXISTING LEAD-BASED PAINT CONTAMINATED CEILING

TILE / GRID / LIGHTS - PROTECT/SUSPEND ALL EXISTING CEILING

MOUNTED DEVICES FOR REINSTALLATION IN THE SAME PLACE AT

NEW CEILING - SEE RCP FOR LIGHTS TO PROTECT/REINSTALL

3576 SF

QUANTITY GRAPHIC

SYMBOL

REMOVING NON-ACM TILE LAID IN ACM MASTIC

19 LF

NOT IN CONTRACT

REMOVE EXTERIOR ASBESTOS CONTAINING STUCCO TO 6'-0"

AFF. ENCAPUSLATE/STABILIZE ACM AT CUT EDGE

6 115 SF

CLEAN EXPOSED VAULT SURFACES OF POTENTIAL LEAD PAINT

DUST/CHIPS

9' - 0"

11' - 8"

8' - 8"

7' - 8"

9' - 0"

7' - 8"

8' - 3"

9' - 0"

7' - 7"

8' - 7"

7' - 7"

6' - 6"

8' - 9"

8' - 0"

8' - 9"

7' - 3" 11' - 3"

8' - 0"

SD

FAS

FAS

SD

SD

SD

FAS

SM

ME

ME

MEME

SD

FASFAS

FAS

SD

ME

SCSD

FAS

FAS

OS

OS

FAS

FASOS

ME

7' - 5"

FAS

TYP

BREAK

GW05A

OPEN WORK

GW04

CONFERENCE

GW07

CONFERENCE

ROOM

GW08

OFFICE

GW09A

OFFICE

GW09

WAITING

GW10

1 1

2 2

CORRIDOR

H0011

EXISTING PARTITION OR WALL

TO REMAIN

NEW PARTITION

NORTH ARROW

SYMBOLS

EXISTING PARTITION OR

CONSTRUCTION TO BE

REMOVED

EXISTING DOOR TO

REMAIN

NEW DOOR

ROOM NAME AND NUMBER

SECTION - BUILDING

CEILING HEIGHT

EXISTING DOOR TO BE REMOVED

PARTITION TYPE01

KEYNOTE#

AD888

AD888

SIM

SECTION - WALL

SECTION - CASEWORK

PLAN

NORTH

TRUE

NORTH

ARCHITECTURAL ANNOTATION

ARCHITECTURAL MODELING

Room Name

10'-0"

NOT ALL SYMBOLS ARE USED

NOT ALL SYMBOLS ARE USED

AD888

SECTION - DETAIL

NOT IN

CONTRACT

th re e in c h e s o n e fo o t o n e a n d o n e h a lf in c h e s o n e fo o t o n e in c h o n e fo o t th re e q u a rt e rs in c h o n e fo o t o n e h a lf in c h o n e fo o t th re e e ig h th s in c h o n e fo o t o n e q u a rt e r in c h o n e fo o t o n e e ig h th in c h o n e fo o t

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

Veterans Health

Administration

VA FORM 08-6231

Drawing Title Project Title

Location

Date Checked Drawn

Project Number

Building Number

Drawing Number

CONSULTANTS:

Drawing # of

EHRM CERNER ADMIN SPACE

VA Health Care System Approval:

Revision: Date:

ARCHITECT/ENGINEER:

U.S. DEPARTMENT OF VETERANS AFFAIRS

VA ST. LOUIS HEALTH CARE SYSTEM

FACILITIES & ENGINEERING SERVICE

JEFFERSON BARRACKS

1 JEFFERSON BARRACKS DRIVE - ST. LOUIS, MO 63125

UNITED STATES OF AMERICA

/2

/2

:5 :1

P

M

01-HA-011

HAZARDOUS ABATEMENT

HT

CM04/22/21

657-21-711JB

CONSTRUCTION DOCUMENTS

1/8" = 1'-0"

HAZARDOUS ABATEMENT PLAN

ASBESTOS AND LEAD ABATEMENT GENERAL NOTES

1. THE SCOPE OF THE ASBESTOS RELATED WORK CONSISTS OF REMOVING

APPROXIMATELY 3600 SF OF NON-ACM TILE LAID IN ACM MASTIC AND

APPROXIMATELY 115 SF OF EXTERIOR ASBESTOS CONTAINING STUCCO. LEAD

RELATED WORK CONSISTS OF THE DEMOLITION OF LEAD CONTAMINATED CEILINGS

AND STABILIZING LEAD-BASED PAINT ON THE CONCRETE CEILINGS

2. WIPE DOWN ALL EXPOSED SURFACES AND EXISTING COMPONENTS TO REMAIN THAT

WERE POSSIBLEY EXPOSED TO LEAD CONTAINING DUST OR PAINT CHIPS.

(DIFFUSERS, FCU'S ETC.)

3. THE ABATEMENT, DEMOLITION AND STABLIZATION WILL BE CONDUCTED INSIDE

NEGATIVE PRESSURE GROSS REMOVAL CONTAINMENTS AND ALL WORK SHALL BE

CONDUCTED IN ACCORDANCE WITH ALL FEDERAL, STATE, AND LOCAL REGULATIONS

AND THE CONTRACT SPECIFICATIONS.

4. ALL ABATEMENT WORK SHALL BE CONDUCTED IN MULTIPLE PHASES DURING

ADMINISTRATIVE HOURS (8:00 AM TO 4:30 PM) MONDAY - FRIDAY

5. WORK SCHEDULES AND LIMITS OF ABATEMENT SHALL BE COORDINATED WITH THE

VA COR AND VPIH FOR APPROVALS, UNLESS OTHERWISE INDICATED ON THE

KEYNOTES.

6. THE ABATEMENT CONTRACTOR SHALL SUBMIT A DETAILED WORK PLAN AND

ABATEMENT SCHEDULE WITH THE REQUIRED SUBMITTALS. ANY CHANGES TO THE

PROCEDURES, CONTAINMENT LIMITS AND PHASING SHALL BE SUBMITTED TO THE VA

COR AND VPIH FOR APPROVALS.

7. THE LOCATIONS AND QUANTITIES SHALL BE FIELD VERIFIED BY THE ABATEMENT

CONTRACTOR.

8. THE LIMITS OF REMOVAL AND EXTENT OF THE CONTAINMENTS SHALL BE VERIFIED

WITH THE VA COR AND VPIH. FOR CLARITY, THE DRAWINGS ONLY SHOW

REPRESENTATIVE LOCATIONS.

9. ALL LOADOUT PROCEDURES SHALL BE COORDINATED WITH THE VA COR AND VPIH.

10. ALL POLYETHYLENE SHEETING USED FOR THE ABATEMENT PROJECT SHALL FIRE

RETARDANT.

11. THE LOCATIONS OF ABATEMENT DECONTAMINATION UNITS AND WASTE DISPOSAL

CONTAINERS SHALL BE FIELD VERIFIED WITH THE VA COR AND VPIH.

12. SEE DEMOLITION ICREA PLAN FOR TEMPORARY PARTITION AND INFECTION

CONTROL DETAILS.

13. ALL PERIMETER AIR MONITORING AND CLEARANCE SAMPLING WILL BE CONDUCTED

BY THE VPIH.

14. ALL LEAD WASTE SHALL BE TESTED BY THE ABATEMENT CONTRACTOR USING TCLP

ANALYTICAL METHODS TO DETERMINE PROPER WASTE DISPOSAL METHODS.

15. CPIH TO PROVIDE ALL SAMPLING & MONITORING NEEDED FOR LEAD

ABATEMENT/REMOVAL

16. TRACE AMOUNTS OF LEAD BELOW THE EPA HUD DEFINITION OF LEAD-BASED PAINT

WERE IDENTIFIED IN THE PROJECT AREAS. IT SHOULD BE NOTED THAT OSHA DOES

NOT RECOGNIZE THIS AS A THRESHOLD VALUE FOR LEAD EXPOSURE. ALTHOUGH

THE POTENTIAL LEAD HAZARD FOR NORMAL DEMOLITION OR CONSTRUCTION

ACTIVITIES IS LOW, ACTUAL LEAD EXPOSURE MAY VARY SIGNIFICANTLY DEPENDING

UPON THE SPECIFIC TASK, PROCEDURE AND OTHER WORK AREA CONDITIONS.

PROPER OSHA COMPLIANCE IS CONSIDERED PERFORMANCE BASED AND INCLUDES

EVALUATING POTENTIAL WORK EXPOSURES WITH AIR MONITORING OR BIOLOGICAL

EXPOSURE MONITORING (BLOOD LEAD TESTING), IF REQUIRED. UNLESS THE

DEMOLITION CONTRACTOR HAS HISTORICAL DATA DOCUMENTING THIS POTENTIAL

EXPOSURE, PERSONAL AIR SAMPLING SHALL BE CONDUCTED BY THE CPIH ON

REPRESENTATIVE TASKS TO DOCUMENT A NEGATIVE EXPOSURE FOR LEAD.

17. TEMPORARY LIGHTING OF SUFFICIENT LUMINOSITY SHALL BE PROVIDED FOR AND

USED BY THE ABATEMENT CONTRACTOR DURING THE ABATEMENT PROCESS

18. FIBERGLASS PIPE INSULATION WILL BE PRESENT IN ABATEMENT CONTAINMENTS.

PROPERLY WRAP AND PROTECT AS REQUIRED.

IMG A - INSIDE SHAFT LOOKING

NORTH

IMG B - INSIDE SHAFT LOOKING SOUTH

1/8" = 1'-0"

HAZARDOUS ABATEMENT CEILING PLAN

REMOVE ACM

CONTAINING

EIFS/PLASTER

REMOVE

CONTAMINATED

DUCT & GYP. BD.

REMOVE ACM

CONTAINING

EIFS/PLASTER

REMOVE

CONTAMINATED

DUCT

STABLIZE

CONTAMINATED

FRAMING

STABLIZE

CONTAMINATED

FRAMING

FE

FAP

FAP

UP

EQUIP.

PIT

EXIST.

EP

TYP

OPEN WORK

GW04

CONFERENCE

ROOM

GW08

OFFICE

GW09A

OFFICE

GW09

WAITING

GW10

CONFERENCE

GW07

BREAK

GW05A

OPEN WORK

GW04

A. EXISTING CONDITIONS ARE BASED ON INFORMATION OBTAINED

FROM EXISTING DRAWINGS AND FIELD SURVEY, AND WILL NOT

BE CONSTRUED AS "AS BUILT." THE CONTRACTOR WILL FIELD

VERIFY EXISTING CONDITIONS PRIOR TO ONSET OF

CONSTRUCTION.

B. CONTRACTOR WILL COMPLY WITH ALL INFECTIOUS CONTROL

REQUIREMENTS OF THE FACILITY. REVIEW REQUIREMENTS

PRIOR TO THE START OF CONSTRUCTION.

C. NOTES WHICH DO NOT HAVE ARROWS TO SPECIFIC ITEMS

INDICATE MATERIAL TO BE REMOVED FOR ENTIRE ROOM IN

WHICH NOTE OCCURS.

D. MAKE ALL DEMOLITION CLEAN AND COMPLETE IN A MANNER

SUITABLE FOR NEW FINISHES AND SURFACES.

E. WHEN DEMOLITION CAUSES OR EXPOSES DAMAGE TO FLOOR

SLAB, WALL, OR CEILING SURFACES WHICH WILL REMAIN IN THE

FINISHED WORK, SUCH CONDITIONS WILL BE REPAIRED AND

LEVELED AS REQUIRED TO RECEIVE NEW FINISHES. REPAIRS

MUST BE ACCEPTABLE TO OWNER.

F. THE CONTRACTOR WILL CLEAN, PATCH, AND REPAIR EXISTING

SURFACES AFFECTED DURING DEMOLITION AND CONSTRUCTION

TO MATCH EXISTING ADJACENT SURFACES. REPAIRS WILL BE

MADE AS TO MATCH EXISTING CONSTRUCTION IN MATERIAL,

METHOD, TECHNOLOGY, COLOR PATTERNS, ETC.

G. ALL DOORS SHOWN DASHED ARE TO BE REMOVED. ASSOCIATED

DOOR FRAME TO REMAIN UNLESS NOTED OTHERWISE.

H. THE CONTRACTOR WILL PROTECT THE EXISTING FLOOR FINISHES

TO REMAIN FROM DAMAGE THROUGHOUT CONSTRUCTION.

I. REMOVE EXISTING FLOOR BASE WHERE NEW FINISHES ARE

REQUIRED. CLEAN AND PREPARE SUBSTRATES AS REQUIRED TO

PRODUCE A FLAT, EVEN SURFACE IN A MANNER SUITABLE TO

ACCEPT NEW FINISHES.

J. PATCH FLOOR PENETRATIONS RESULTING FROM REMOVAL OF

EXISTING DUCTWORK, PIPING, AND ELECTRICAL RACEWAYS. FILL

PENETRATIONS WITH CONCRETE, FULL FLOOR THICKNESS AND

MAINTAIN FIRE-RESISTIVE RATING OF FLOOR SYSTEM. FINISH

SUBSTRATE IN A MANNER SUITABLE FOR NEW FLOOR FINISHES.

K. THE CONTRACTOR WILL FILL ALL WALL PENETRATIONS

RESULTING FROM THE REMOVAL OF EXISTING MEP DEVICES IN

THE INTERIOR WALLS TO REMAIN. THE PENETRATIONS WILL BE

FILLED FLUSH WITH, AND OF THE SAME MATERIALS AS, THE

SURROUNDING WALLS, THIS INCLUDES WORK ABOVE ALL

CEILINGS. THE CONTRACTOR WILL IN-FILL ALL OPENINGS IN

EXTERIOR WALLS RESULTING FROM THE REMOVAL OF LOUVERS,

EXHAUST FANS, ETC. THE OPENINGS WILL BE FILLED FLUSH

WITH, AND OF THE SAME MATERIALS AS, THE SURROUNDING

WALLS.

L. FOR ALL EXISTING ELECTRICAL DEVICES TO BE REMOVED FROM

WALLS WHICH REMAIN, CONTRACTOR SHALL DISCONNECT

POWER, REMOVE CONDUCTORS AND REMOVE DEVICE. WHERE

FIXTURES, EQUIPMENT OR DEVICES ARE REMOVED, PATCH THE

SURFACE AS REQUIRED TO MATCH THE EXISTING WALL

CONSTRUCTION.

M. ALL EXISTING ELECTRICAL EQUIPMENT, MISCELLANEOUS CABLES,

CONDUITS, WIRING DEVICES, ETC. TO BE REMOVED SHALL

BECOME THE PROPERTY OF THE CONTRACTOR, UNLESS

OTHERWISE NOTED. THE CONTRACTOR SHALL REMOVE THESE

ITEMS FROM THE PREMISES.

N. NOISE PRODUCING WORK ABOVE 85 DB WILL NOT BE ALLOWED

DURING NORMAL WORKING HOURS AND MUST BE SCHEDULED

WITH THE VA PROJECT ENGINEER FOR OTHER TIMES. THIS

INCLUDES JACKHAMMERING CONCRETE, SAW CUTTING

CONCRETE, FREQUENT HAMMER DRILLING OF CONCRETE, ETC.

GENERAL DEMOLITION NOTES

1. REMOVE EXTERIOR VENT AND PATCH W/ MTL PLATE TO MATCH ADJACENT

2. REMOVE EXISTING DEMOUNTABLE METAL WALLS INCLUDING TRACK. PREP

AS REQUIRED TO RECIEVE NEW FINISHES. REMOVE SURFACE MOUNTED

POWER AND DATA OUTLETS & WIRING BACK TO SOURCE.

3. SCRAPE & SKIM EXISTING WALL SURFACES TO RECIEVE NEW PAINT. TYP- @

ALL EXITING WALLS

4. REMOVE EXISTING AHU AND ASSOCIATED ELEC. REMOVE ASSOCIATED

PIPING BACK TO MAIN AND CAP.

5. NOT USED

6. REMOVE AND DISCARD EXISTING CASEWORK TYP. THROUGHOUT WORK

AREA U.N.O. REMOVE ANY ASSOCIATED ELECTRIC BACK TO JUNCTION BOX.

7. REMOVE EXISTING SINK/EYEWASH. REMOVE & CAP ASSOCIATED

PLUMBING BACK TO MAIN. TURN OVER EYEWASH TO MEDICAL CENTER.

8. REMOVE EXISTING SINK AND CASEWORK. REMOVE AND CAP ASSOCIATED

PLUMBING BACK TO MAIN.

9. REMOVE EXISTING COLD WAVE UNIT, ASSOCIATED DUCTWORK,

DISCONNECT SWITCH & ASSOCIATED ELEC. REMOVE ASSOCIATED

PLUMBING - CAP AT SOURCE

10. REMOVE EXISTING SPEAKER AND 'NOW SERVING' SIGN NEAR CEILING.

REMOVE ANY ASSOCIATED WIRING BACK TO SOURCE.

11. REMOVE EXISTING EYEWASH. REMOVE PIPE BACK TO MAIN & CAP

12. RETAIN CARD READER ON CASEWORK FOR REINSTALLATION ON NEAREST

WALL.

13. PROTECT EXISTING MOBILE AIR CONDITIONER FOR REINSTALLATION

UNDER NEW CASEWORK - SEE PLAN AND ELEVATIONS

14. REMOVE EXISTING EYEWASH AND TURN OVER TO MC. REMOVE

ASSOCIATED DRAIN/SUPPLY AS NECCESSARY TO REPORPOSE FOR NEW

KITCHEN SINK.

15. REMOVE EXISTING PLASTIC CORNER GUARDS THROUGHOUT SPACE &

PREP FOR INSTALLATION OF NEW SS CORNER GUARDS TO 8'-0" AFF.

16. DEMO WALL FOR INSTALLATION OF EXHAUST FAN IN EXISTING OPENING.

17. REMOVE EXISTING WATER SUPPLY FOR EYEWASH BACK TO MAIN.

18. REMOVE EXISTING PASS THRU - PREP FINISHES FOR INFILL

19. REMOVE EXISTING WINDOW INCLUDING SS TRANSACTION TOP AND

CAMERA AND ASSOCIATED WIRING- PREP FINISHES FOR INFILL

20. REMOVE EXISTING CHAIR RAIL. PREP FOR PAINT

21. REMOVE EXISTING WALL PROTECTION - PREP FOR PAINT.

22. REMOVE EXISTING FRAME/DISPLAY. PATCH/PREP SURFACES FOR PAINT.

23. REMOVE EXITING FLOOR TILE AND PREP FOR INSTALLATION OF NEW

FLOORING.

24. REMOVE EXISTING DOOR. EXISTING FRAME TO REMIAN. SEE DOOR

SCHEDULE.

25. REMOVE EXISTING WOOD TRIM AT TOP OF VAULT

26. RELOCATE FIRE EXTINGUISHER IN SAME ROOM. SEE PLAN

27. REMOVE EXISTING RUBBER BASE. PREP TO RECEIVE NEW BASE.

DEMOLITION PLAN KEYNOTES#

EXISTING PARTITION OR WALL

TO REMAIN

NEW PARTITION

NORTH ARROW

SYMBOLS

EXISTING PARTITION OR

CONSTRUCTION TO BE

REMOVED

EXISTING DOOR TO

REMAIN

NEW DOOR

ROOM NAME AND NUMBER

SECTION - BUILDING

CEILING HEIGHT

EXISTING DOOR TO BE REMOVED

PARTITION TYPE01

KEYNOTE#

AD888

AD888

SIM

SECTION - WALL

SECTION - CASEWORK

PLAN

NORTH

TRUE

NORTH

ARCHITECTURAL ANNOTATION

ARCHITECTURAL MODELING

Room Name

10'-0"

NOT ALL SYMBOLS ARE USED

NOT ALL SYMBOLS ARE USED

AD888

SECTION - DETAIL

NOT IN

CONTRACT

th re e in c h e s o n e fo o t o n e a n d o n e h a lf in c h e s o n e fo o t o n e in c h o n e fo o t th re e q u a rt e rs in c h o n e fo o t o n e h a lf in c h o n e fo o t th re e e ig h th s in c h o n e fo o t o n e q u a rt e r in c h o n e fo o t o n e e ig h th in c h o n e fo o t

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

Veterans Health

Administration

VA FORM 08-6231

Drawing Title Project Title

Location

Date Checked Drawn

Project Number

Building Number

Drawing Number

CONSULTANTS:

Drawing # of

EHRM CERNER ADMIN SPACE

VA Health Care System Approval:

Revision: Date:

ARCHITECT/ENGINEER:

U.S. DEPARTMENT OF VETERANS AFFAIRS

VA ST. LOUIS HEALTH CARE SYSTEM

FACILITIES & ENGINEERING SERVICE

JEFFERSON BARRACKS

1 JEFFERSON BARRACKS DRIVE - ST. LOUIS, MO 63125

UNITED STATES OF AMERICA

/2

/2

:5 :1

P

M

01-AD-100

DEMO PLANS

HT

CM04/22/21

657-21-711JB

CONSTRUCTION DOCUMENTS

1/8" = 1'-0"

DEMO PLAN

GENERAL NOTE: ALL UTILITY OUTAGES WILL BE

REVIEWED, COORDINATED WITH MC. CONTRACTOR

SHOULD PLAN FOR OUTAGES TO BE AFTER HOURS

PLAN

NORTH

FAP

FAP

UP

EQUIP.

PIT

OPEN WORK

GW04

CONFERENCE

ROOM

GW08

OFFICE

GW09A

OFFICE

GW09

BREAK

GW05A

CONFERENCE

GW07

01-AE-100 5

STORAGE

GW04B

A

04B

CORRIDOR

H0011

04A

Room

GW04A

EXISTING PARTITION OR WALL

TO REMAIN

NEW PARTITION

NORTH ARROW

SYMBOLS

EXISTING PARTITION OR

CONSTRUCTION TO BE

REMOVED

EXISTING DOOR TO

REMAIN

NEW DOOR

ROOM NAME AND NUMBER

SECTION - BUILDING

CEILING HEIGHT

EXISTING DOOR TO BE REMOVED

PARTITION TYPE01

KEYNOTE#

AD888

AD888

SIM

SECTION - WALL

SECTION - CASEWORK

PLAN

NORTH

TRUE

NORTH

ARCHITECTURAL ANNOTATION

ARCHITECTURAL MODELING

Room Name

10'-0"

NOT ALL SYMBOLS ARE USED

NOT ALL SYMBOLS ARE USED

AD888

SECTION - DETAIL

NOT IN

CONTRACT

1. INFILL OPENING. MATCH EXISTING CONDITIONS

2. MAINTAIN CLEAR AREA FOR AIR INTAKE AT EXISTING AIR

CONDITIONER

3. REINSULATE EXISTING 1 1/2"-2" STEAM PIPE AT 12" AFF. CONTACT

COR IN THE EVENT OF ANY CUTTING TO IDENTIFY ANY SPECIAL

PRECAUTIONS.

4. INFILL WALL AT REMOVED PASS THRU. MATCH EXISTING

CONDITIONS.

5. PROVIDE DOMESTIC WATER AND HOT WATER CONNECTION WITH

VALVES AT TIE-IN ABOVE CEILING IN ADJACENT SPACE AND AT

FIXTURE.

6. REWORK OPENING TO RECEIVE NEW HM DOOR & FRAME. FINISH

WITH DRYWALL. PAINT TO MATCH ADJACENT FINISHES. DOOR

HARDWARE TO INCLUDE 1 1/2 PAIR HINGES, CLOSER, LEVER

HANDLE WITH CLASSROOM LOCKSET. PAINT PT-1

7. PROVIDE & INSTALL BUTTON FOR AUTOMATIC DOOR OPENER -

HARD WIRED W/ SURFACE MOUNT CONDUIT

8. PROVIDE & INSTALL NEW OPERATOR AND AUTOMATIC DOOR

OPERATOR FOR EXISTING DOOR

9. INFILL WHERE EXHAUST FAN WAS REMOVED TO MATCH

ADJACENT CONSTRUCTION/FINISHES.

10. PROVIDE & INSTALL EXHAUST FAN

11. PROVIDE WATERLINE FOR VA PROVIDED REFRIGERATOR

12. PROVIDE COVER FOR EXISTING RADIATOR TO REMAIN.

13. PROTECT EXISTING PIPE AT THE FLOOR W/ 16 GA ALUMINUN

METAL SHROUD -PAINT

14. NOT USED

15. PATCH AND PAINT AT REMOVED CHAIR RAIL

16. PATCH AND PAINT AT REMOVED WALL PROTECTION

17. PROVIDE INSULATION AT EXISTING PIPES

18. EXISTING VERTICAL PIPE TO REMAIN - PAINT TO MATCH WALL

19. CLOSE OFF AREA BEHIND VAULT & INSTALL 6' ACCESS PANEL

20. INFILL EXISTING DOOR FRAME AT DOOR TO REMAIN WITH GYP

BOARD FLUSH WITH FACE OF FRAME. FINISH/PAINT TO MATCH

ADJACENT.

21. INFILL GAP BETWEEN EXISTING VAULT AND WALL WITH GYP. BD.

PAINT TO MATCH ADJACENT.

22. PATCH ANY HOLES IN PIPE COVERING. PAINT.

23. INSTALL 5/8" EXTERIOR GRADE GYP. BD. - PAINT TO MATCH

ADJACENT FINISHES

FLOOR PLAN KEYNOTES#

4' - 4" 3' - 0" 5' - 11"

OPEN EXISTING WALL AT

EXISTING WALL

PENETRATION - PROVIDE &

INSTALL EXHAUST FAN

PROVIDE FINAL

CONNECTIONS TO

RELOCATED MOBILE AIR

CONDITIONER

OPEN

FRIG

BY MC

LOCKABLE PLAM CABINETS

RB1

SOLID SURFACE TOP W/ 4"

INTEGRAL BACKSPLASH 4

01-AE-100

01-AE-100

ANGLED PLAM APRON

SINGLE BOWL STAINLESS

STEEL SINK W/ GOOSENECK

AND WRISTBLADE HANDLES.

GC TO PROVIDE HOT WATER

SUPPLY & WRAP EXPOSED

PIPE PER SPEC

Wall Base; REF: Schedule

FIN Floor; REF: Schedule

3-5/8" MTL Studs

@ 16" OC

Soffit Above

(1) Layer 5/8" GWB Type "X" Both Sides

STC 39

Exisitng Sub-floor / Slab

Partition Type Not to ScaleA

4 7/8"

Notes:

1. Head Similar

2. Provide (3) Anchors MIN per Jamb; (4) at Rated Partitions

3. Refer to Door Schedule for Ratings Required

4. HM Jamb Throat 1/8" Larger than Partition, Caulk and Paint , TYP

Double Stud @ Jamb

Welded HM Frame

X

P-Type;

REF: Plan

/1

1/2"

/3

1 13/16" ± Varies

REF:

Schedule

ADA COMPLIANT SINK & FAUCET; REF:

SPECS

1/2' SOLID SURFACE COUNTERTOP

- SCRIBE TO WALL

PLAM ON 3/4” MDF

1"

REMOVABLE GUARD - PLAM

ON 3/4” MDF, ATTACH TO

WOOD BLOCKJING BEYOND

WITH PANEL CLIPS

WOOD BLOCKING BEYOND,

ATTACH TO SIDE PANEL/WALL

8" MIN.

10" MIN.

M

IN

PLAM IN 1/4” MDF BACKING

RB-1

/4

3/4" EXTERIOR GRADE MDF

/2

4" BACKSPLASH

SOLID SURFACE SIDESPLASH - WHERE OCCURS

/8

2' - 1"

WASTE DISPOSER

PROTECT ANY EXPOSED PIPE PER

SPEC

CABINET PULL

(VERT. MOUNT)

1/2" SOLID SURFACE

COUNTERTOP

SEALANT

PLAM BASE CABINET;

NOTE: CABINET

INTERIOR, & ADJ.

SHELF TO BE BLACK

MELAMINE

SCHEDULED BASE

2X FTWD BLOCKING

2' - 1" U.O.N.

R E

F

E

LE

V A

T

IO

N S

2' - 0" 3"

R

'-1 /2

" T Y P

/2

TYP. SOLID SURFACE

EDGE PROFILE

/8

/2

TREATED WOOD BLOCKNIG

@ STRAP SUPPORT (TYP.)

2x4 FIRE TREATED WD CLEAT (PAINT)

2" DIA. GROMMET (WHERE OCCURS)

REF: ARCHITECTURE DRAWINGS

SS COUNTERTOP - SCRIBE TO WALL

2X FTWD BLOCKING(TYP.)

4" PLAM SS BACKSPLASH(WHERE OCCURS)

REF: FINISH SCHEDULE AND PLANS

2' - 6"

0'

/2

1' - 0" 45.00°

MTL STRAP SUPPORT BRACKET (PAINT)

R E

: E

LE

V A

T

IO

N

Ceiling

Light Gauge Metal Studs

@ 16" OC

Structure Above

(1) Layer 5/8" Gyp. Bd. Paint TO 4" above CLG

Exisitng Vault th re e in c h e s o n e fo o t o n e a n d o n e h a lf in c h e s o n e fo o t o n e in c h o n e fo o t th re e q u a rt e rs in c h o n e fo o t o n e h a lf in c h o n e fo o t th re e e ig h th s in c h o n e fo o t o n e q u a rt e r in c h o n e fo o t o n e e ig h th in c h o n e fo o t

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

Veterans Health

Administration

VA FORM 08-6231

Drawing Title Project Title

Location

Date Checked Drawn

Project Number

Building Number

Drawing Number

CONSULTANTS:

Drawing # of

EHRM CERNER ADMIN SPACE

VA Health Care System Approval:

Revision: Date:

ARCHITECT/ENGINEER:

U.S. DEPARTMENT OF VETERANS AFFAIRS

VA ST. LOUIS HEALTH CARE SYSTEM

FACILITIES & ENGINEERING SERVICE

JEFFERSON BARRACKS

1 JEFFERSON BARRACKS DRIVE - ST. LOUIS, MO 63125

UNITED STATES OF AMERICA

/2

/2

:5 :1

P

M

01-AE-100

FLOOR PLANS

HT

6 164

CM04/22/21

657-21-711JB

CONSTRUCTION DOCUMENTS

1/8" = 1'-0"

FLOOR PLAN

1/4" = 1'-0"

BREAKROOM ELEVATION

PLAN

NORTH

Door Schedule

Mark Size Door TYPE Frame Type

Frame Material Jamb Detail Head Detail Door Hardware Set

04A 3-0 x 7-0 MTL EXIST.-PT4 PAINT PT-4 EXIST EXIST HW-4A REMOVE & SALVAGE EXISTING MAG LOCK & COORDINATE

INSTALL W/ NEW HARDWARE

04B 2-6 x 6-0 MTL HM -P4 PAINT PT-4 3/A-101 3/A-101 HW-11

07 3-0 x 7-0 MTL HM -P4 PAINT PT-4 3/A-101

SIM

3/A-101

SIM

HW-3

08 3-0 x 7-0 MTL EXIST.-PT4 PAINT PT-4 EXIST EXIST HW-3

011 3-8 x 7-0 MTL EXIST.-PT4 PAINT PT-4 EXIST EXIST HW-4A REMOVE & SALVAGE EXISTING MAG LOCK & COORDINATE

INSTALL W/ NEW HARDWARE

3" = 1'-0"

Detail - HM Door Jamb

1" = 1'-0"

DETAIL - ADA SINK

1" = 1'-0"

DETAIL - BASE CABINET

1" = 1'-0"

DETAIL - COUNTERTOP SUPPORT LEG

1" = 1'-0"

Detail at Vault-Ceiling Connection

(PAIR)

9' - 0"

11' - 6"

11' - 8"

6' - 6"

11' - 3"

SD SM

SD

FASFAS ME

SCSD

FAS

CONFERENCE

GW07

OPEN WORK

GW04

CONFERENCE

ROOM

GW08

OFFICE

GW09A

OFFICE

GW09

BREAK

GW05A

FAS

SD

FAS

FAS

FAS

FAS

FAS

FAS

FAS

FAS

FAS

FAS

FAS

SD

SD

SD

SD

SD

SD

SD

OS

OS

OS

L

IG

H T

IN

G

Z O

N E

L

IG

H

T

IN

G Z

O N

E

L

IG

H T

IN

G

Z O

N E

STORAGE

GW04B

HW

CW

CW

HW

7 7

9' - 0"

8' - 3"

8' - 7"

8' - 7"

7' - 5"

9' - 0"

7' - 7"

9' - 0"

7' - 7"

8' - 9"

7' - 3"

7' - 8"

8' - 8"

01-AE-100

CORRIDOR

H0011

NIC

N.I.C.

N.I.C.

N.I.C.

N E

W C

L G

E X

IS

T

C

L G

N

.I .C

8' - 0"

1. EXISTING MOTION SENSING LIGHTING CONTROL DEVICE TO BE

REWIRED TO ACHIEVE LIGHTING ZONES SHOWN ON PLLAN.

COORDINATE GROUPINGS AND LOCATIONS WITH COR. EACH

ZONE TO HAVE SEPARATE OCCUPANCY SENSOR.

2. EXISTING GYP. BD. CEILING TO REMAIN - PAINT

3. EXISTING LIGHTING TO REMAIN - PROTECT AND REINSTALL AT

CEILINGS TO BE REPLACED.

4. PROVIDE AND INSTLALL MOTION SENSING LIGHTING CONTROL

DEVICE.

5. REMOVE EXISTING CAMERA AND ASSOCIATED WIRING BACK

TO SOURCE. TURN OVER DEVICE TO MEDICAL CENTER.

6. REMOVE EXISTING WATER SUPPLY FOR EYEWASH BACK TO

MAIN

7. REPLACE EXISTING SURFACE MOUNTED LIGHT FIXTURES WITH

STANDARD 2X4 LED LAY IN FIXTURE

CEILING PLAN KEYNOTES#

EXIT LIGHT

24"x48" LAY-IN LED MECH. RETURN AIR

DIFFUSER

MECH SUPPLY AIR

DIFFUSER

REFLECTED CEILING PLAN LEGEND

GYP. BD. CEILING

CEILING HEIGHTX-X

12" x 48" LED

STRIP FIXTURE

24"x48" LAY-IN

LED -

EMERGENCY

24"x24" LAY-IN LED

SPRINKLER HEAD

th re e in c h e s o n e fo o t o n e a n d o n e h a lf in c h e s o n e fo o t o n e in c h o n e fo o t th re e q u a rt e rs in c h o n e fo o t o n e h a lf in c h o n e fo o t th re e e ig h th s in c h o n e fo o t o n e q u a rt e r in c h o n e fo o t o n e e ig h th in c h o n e fo o t

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

Veterans Health

Administration

VA FORM 08-6231

Drawing Title Project Title

Location

Date Checked Drawn

Project Number

Building Number

Drawing Number

CONSULTANTS:

Drawing # of

EHRM CERNER ADMIN SPACE

VA Health Care System Approval:

Revision: Date:

ARCHITECT/ENGINEER:

U.S. DEPARTMENT OF VETERANS AFFAIRS

VA ST. LOUIS HEALTH CARE SYSTEM

FACILITIES & ENGINEERING SERVICE

JEFFERSON BARRACKS

1 JEFFERSON BARRACKS DRIVE - ST. LOUIS, MO 63125

UNITED STATES OF AMERICA

/2

/2

:5 :1

P

M

01-AE-101

CEILING PLANS

HT

6 164

CM04/22/21

657-21-711JB

CONSTRUCTION DOCUMENTS

1/8" = 1'-0"

CEILING PLAN

GENERAL RCP NOTES:

1. PROVIDE NEW CEILING THROUGHOUT PROJECT AREA

AT PREVIOUS HEIGHTS U.N.O. CONTRACTOR TO

FIELD VERIFY EXITING CONSTRUCTION PRIOR TO

DEMOLITION FOR REINSTALLATION OF ALL CEILING

COMPONENTS / DEVICES IN PREVIOUS LOCATIONS.

2. A REDUCTION OF THE NUMBER OF CEILINGS AND

MAXIMIZING THE CEILING HEIGHT IS THE

PREFFERENCE OF THE MEDICAL CENTER.

WHENEVER POSSIBLE, IDENTIFY ANY OPPORTUNITIES

TO SIMPLIFY AND RAISE THE CEILING AND

COORDINATE SUCH CHANGES WITH COR.

3. MODIFY EXISTING MOTION SENSING LIGHTING

CONTROL DEVICES AS NECESARY TO ACHIEVE 3 THE

LIGHTING ZONES AS SHOWN ON PLAN. COORDINATE

FINAL GROUPINGS AND LOCATIONS WITH COR. EACH

ZONE TO HAVE SEPERATE OCCUPANCY SENSOR.

MODIFY SWITCHES ACCORDINGLY.

4. ALL LIGHT FIXTURES ARE NEW LED LUMINAIRES

U.N.O.

5. PROVIDE DOMESTIC WATER AND HOT WATER

CONNECTION WITH VALVES AT TIE-IN ABOVE CEILING

IN ADJACENT SPACE AND AT FIXTURE.

1. EXISTING PERIMETER RACEWAY AT 48" AFF TO REMAIN.

PLUG OPEN PORTS.

2. REMOVE EXISTING ELECTRICAL PANEL AND ASSOCIATED

WIRING.

3. REMOVE WHIP BACK TO JUNCTION BOX. TYP.

4. EXISTING AIR CONDITIONER AND SHUT OFF TO REMAIN

5. DEMO EMPTY CONDUIT TYP.

6. REMOVE EXISTING DATA JACK AND CABLING

7. REMOVE EXISTING POWER POLE AND WIRING BACK TO

SOURCE.

8. REMOVE CABINET MOUNTED CARD READER AND TURN OVER

TO MC.

ELECTRICAL DEMO KEYNOTES#

FE

FE

FAP

FAP

UP

EQUIP.

PIT

CONFERENCE

ROOM

GW08

OFFICE

GW09A

OFFICE

GW09

BREAK

GW05A

48" (2) 48" 48"

48" (2) 48" 48"48"

48"

36"

EXIST.

EP

J

J

J

3 (4) @ 30"

(2) @ 36"

(2) @ 72"

(2) 84"

72"

OPEN WORK

GW04

(2) 84"

CR

TYP

FE

J

T

48"

48"

X2

X2

J

J

X5

(6) 48"

X4

X3

X6 J

X2

X4

J

T

T

@CLG

T

T

J

48"

@CLG

48"

X5X5 30"

T

48"

48"

48"

48"

GFCI

J

CR

CONFERENCE

GW07

GENERAL NOTES: ELEC DEMO PLAN

1. REMOVE ANY REMAINING WHIPS BACK TO

JUNCTION BOXES TYP.

2. EXISTING ACCESS PANELS TO REMAIN

3. REMOVE ALL DATA OUTLETS AND CABLING BACK

TO CLOSET 1W01

4. REMOVE CAMERA & ASSOCIATED

WIRING/CONDUIT BACK TO SOURCE. TURN OVER

TO MC.

5. REMOVE JBOX AND ASSOCIATED WIRING BACK TO

SOURCE

6. ALL EXISTING PHONE LINES TO REMAIN.

7. REMOVE ANY EMPTY CONDUIT.

CR

e e e e e e e 72"

OPEN WORK

GW04

BREAK

GW05A

CONFERENCE

GW07

CONFERENCE

ROOM

GW08

OFFICE

GW09A

OFFICE

GW09

48" 48"

48" 48"

48"

J

J

J

(2) @ 72"

72"

(2) 84"

J

48"

48"

J

J

X4

J

J

J

48"

48"

48"

48"

GFCI

J e e e e e e e 72"

X2

X5

NOTE:

1. ALL ELECTRIC SHOWN IS

EXISTING U.N.O.

2. FURNITURE SHOWN IS

SUGGESTED BASED ON

PROVIDED DESIGN CRITERIA.

FINAL FURNITURE LAYOUT IS

BY CERNER. TBD.

3. ALL DATA IS TO BE INSTALLED

NEW WITH CAT6A CABLING

BACK TO DATA CLOSET IN

GC11.

4. NEW PATCH PANELS

COORDINATED W/ NEWLY

INSTALLED DATA DROPS

PROVIDE AND

INSTALL NEW

QUAD

RECEPTACLE

EXISTING MECH.

WAITING

GW10

PRINTING AREA

PROVIDE POWER

FOR NEW

AUTOMATIC DOOR

OPERATOR AND

OPENER/BUTTON

PROVIDE & INSTALL

NEW WIRELESS

AUTOMATIC DOOR

OPENER

STORAGE

GW04B

PROVIDE AND

INSTALL NEW

QUAD

RECEPTACLE

CORRIDOR

H0011

1. THE HOSPITAL INTENDS TO OCCUPY ADJACENT AREAS OF WORK WITHIN THE REMODEL AREA DURING DEMOLITION. UTILITIES AND SERVICES TO ANY EXISTING FACILITIES NOT BEING REMODELED SHALL NOT BE INTERUPTED WITHOUT THE PROJECT ENGINEER'S APPROVAL AS TO THE TIME AND DURATION.

2. FOR ALL EXISTING ELECTRICAL DEVICES TO BE REMOVED FROM WALLS WHICH REMAIN, CONTRACTOR

SHALL DISCONNECT POWER, REMOVE CONDUCTORS AND REMOVE DEVICE. WHERE FIXTURES,

EQUIPMENT OR DEVICES ARE REMOVED, PATCH THE SURFACE AS REQUIRED TO MATCH THE EXISTING.

SEE FLOOR PLANS FOR ADDITIONAL DETAILS

3. ALL EXISTING ELECTRICAL EQUIPMENT, MISCELLANEOUS CABLES, CONDUITS, WIRING DEVICES, ETC. TO BE REMOVED SHALL BECOME THE PROPERTY OF THE CONTRACTOR, UNLESS OTHERWISE NOTED. THE

CONTRACTOR SHALL REMOVE THESE ITEMS FROM THE PREMISES.

4. ALL WIRING FOR A CIRCUIT WHICH IS TO BE REMOVED SHALL BE REMOVED BY THE CONTRACTOR BACK

TO THE PANEL WHICH SUPPLIED THE CIRCUIT U.N.O.

5. PROVIDE DEDICATED CIRCUIT FOR EACH WORKSTATION IN TELEHEALTH, A115.

6. WHERE LIGHTS ARE RELOCATED, MOVE ASSOCIATED OCCUPANCY SENSOR.

7. CONTRACTOR SHALL PROVIDE BOXES, CONDUIT, WIRE, AND RECONNECTIONS AS REQUIRED TO

RECONNECT ANY AND ALL EXISTING LIGHT FIXTURES, RECEPTACLES, OR DEVICES REMAINING IN USE.

REMOVAL OF ANY ELECTRICAL EQUIPMENT SHALL NOT AFFECT THE OPERATION OF EQUIPMENT

REMAINING IN USE.

8. A GREEN GROUND SHALL BE RUN WITH ALL FEEDERS AND WITH ALL CIRCUITS TO RECEPTACLES, MOTORS, FIXED EQUIPMENT, AND APPLIANCES.

9. PANELBOARDS AND CIRCUIT BREAKERS SHALL HAVE THE FOLLOWING MINIMUM INTERRUPTING RATINGS:

120/208 - 22,000 AMPERES SYMMETRICAL.

10. CONTINUITY OF ALL SERVICES TO AND FROM THE FACILITIES IN THE EXISTING BUILDING SHALL BE MAINTAINED WITHOUT INTERRUPTION, EXCEPT FOR SUCH PERIODS OF TIME WHICH THE V.A. MAY DESIGNATE. IF TEMPORARY CONNECTIONS, ETC. ARE NECESSARY TO ASSURE THE CONTINUITY OF SERVICE, THEY SHALL BE FURNISHED WITHOUT ADDITIONAL CHARGE TO THE V.A. AND SHALL BE

REMOVED WHEN NO LONGER NECESSARY.

11. ALL INSTALLATIONS AND EQUIPMENT SHALL FOLLOW THE GUIDELINES ESTABLISHED BY THE CURRENT

NATIONAL ELECTRIC CODE.

12. LOCATIONS OF EXISTING DUCTWORK, ELECTRICAL, MECHANICAL, PIPING, CABLE TRAYS, ETC., ARE NOT NECESSARILY SHOWN ACCURATELY ON THE DRAWINGS. FIELD VERIFY THE LOCATIONS OF EXISTING EQUIPMENT, DUCTWORK, PIPING, ETC. AFFECTING THE PERFORMANCE OF THE WORK. NOTIFY THE

CONTRACTING OFFICER'S REPRESENTATIVE IMMEDIATELY IF SIGNIFICANT DISCREPANCIES OR

OMISSIONS ARE DISCOVERED THAT AFFECT PERFORMANCE OF THE WORK.

13. CONTRACTOR SHALL NOT INSTALL CONDUIT, PIPING, LIGHTING, OR OTHER OBSTRUCTIONS UNDER OR ADJACENT TO HVAC EQUIPMENT THAT WILL ELIMINATE OR OBSTRUCT ACCESS TO COILS, MOTORS, VALVES, SWITCHES, PANELS, ETC.

14. EXISTING CIRCUITRY (CONDUIT, BOXES, WIRE, ETC.) MAY BE REUSED AT THE CONTRACTOR'S OPTION AS LONG AS IT MEETS THE SAME SPECIFICATIONS REQUIRED FOR NEW CIRCUITRY. ALL WORK, NEW AND

EXISTING, SHALL COMPLY WITH THE LATEST NEC CODE.

15. DRAWINGS ARE DIAGRAMMATIC AND SHOW THE GENERAL ARRANGEMENT OF EACH SYSTEM. BECAUSE OF THE SMALL SCALE OF DRAWINGS IT IS NOT POSSIBLE TO SHOW OR INDICATE ALL BRANCHES, OFFSETS, FITTINGS, BOXES, AND ACCESSORIES WHICH MAY BE REQUIRED.

16. LOCATIONS OF NEW EQUIPMENT, PIPING, AND ASSOCIATED ITEMS ARE SHOWN ON THE DRAWINGS. THE CONTRACTOR SHALL FIELD COORDINATE LOCATIONS AND ELEVATIONS FOR THE WORK, INCLUDING CONNECTIONS TO EXISTING WORK. REQUIRED OFFSETS, FITTINGS, TRANSITIONS, EXTENSIONS, ETC. TO HAVE A COMPLETE AND FUNCTIONAL SYSTEM ARE INCLUDED IN THE SCOPE OF THE WORK. NOTIFY THE

CONTRACTING OFFICER'S REPRESENTATIVE IMMEDIATELY IF SIGNIFICANT DISCREPANCIES OR

OMISSIONS ARE DISCOVERED THAT AFFECT PERFORMANCE OF THE WORK.

17. ALL RECEPTACLES, OUTLETS, JUNCTION BOXES FOR EQUIPMENT CONNECTIONS, ETC., SHALL BE

MOUNTED 18" ABOVE FINISHED FLOOR UNLESS NOTED OTHERWISE.

18. WORK THAT REQUIRES A UTILITY OR SYSTEM SHUTDOWN; OR THAT MUST BE COMPLETED IN OCCUPIED

AREAS OF THE MEDICAL CENTER MUST BE DONE DURING TIMES OTHER THAN NORMAL WORKING

HOURS. WORK MUST BE SCHEDULED WITH THE VA PROJECT ENGINEER.

19. SEVERE NOISE PRODUCING WORK WILL NOT BE ALLOWED DURING NORMAL WORKING HOURS AND

MUST BE SCHEDULED WITH THE VA PROJECT ENGINEER FOR OTHER TIMES. THIS INCLUDES

JACKHAMMERING CONCRETE, SAWCUTTING CONCRETE, FREQUENT HAMMER DRILLING OF CONCRETE, ETC.

20. CONTRACTOR SHALL PROVIDE AND INSTALL ELECTRIC DISCONNECT SWITCHES FOR ALL EQUIPMENT

REQUIRING DISCONNECT SWITCHES BY THE NATIONAL ELECTRIC CODE WHETHER OR NOT THE

DISCONNECT SWITCH IS SPECIFICALLY SHOWN ON THE DRAWINGS. SWITCHES SHALL BE SIZED FOR THE

SERVICE AND SHALL BE VISIBLE TO THE EQUIPMENT PER THE N.E.C.

21. DUPLEX POWER OUTLETS SHALL BE SPACED AT 10' (TEN FEET) MAX IN FINISHED SPACES UNLESS

OTHERWISE NOTED. MINIMUM 1 (ONE) PER WALL.

22. CONTRACTOR TO COORDINATE ALL POWER RUN ROUTINGS AND CIRCUIT LOCATIONS WITH ANTICIPATED

LOADS IN EACH SPACE.

23. ELECTRICAL LIGHTING SHALL BE COORDINATED IN THE FIELD WITH C.O.R. AT A MINIMUM, INSTALL NUMBER OF FIXTURES DEPICTED ON REFLECTED CEILING PLANS. ALL SPACES INSIDE THE BUILDING, FINISHED AND UNFINISHED SPACES SHALL HAVE CEILING AND LIGHTING.

24. ALL LIGHTING SHALL BE 2X4 L.E.D. FIXTURES, UNLESS NOTED OTHERWISE. COORDINATE TYPE WITH C.O.R. (SIMILAR TO B2 AT JOHN COCHRAN IN RECENTLY RENOVATED SPACE.) SEE REFLECTED CEILING

PLANS FOR APPROXIMATE LOCATIONS.

25. PROVIDE BATTERY-BACKUP L.E.D. LAY-IN 2X4 FIXTURES TO PROVIDE ADEQUATE EGRESS LIGHTING.

26. LIGHT SWITCHES LOCATED AT DOORWAYS TO SPACE UNLESS OTHERWISE NOTED.

27. INSTALL NEW DEVICES IN EXISTING OUTLET BOXES RETAINED IN DEMO. IF NOT FEASABLE TO USE

EXISTING CONTRACTOR SHALL INSTALL NEW SURFACE MOUNTED DEVICES.

28. ROUTE ALL NEW DATA CABLING TO EXISTING DATA ROOM.

29. ROUTE ALL TELEPHONE CABLING TO TELEPHONE CLOSET. CONTRACTOR SHALL PROVIDE NEW PUNCH

DOWN BLOCKS, SIZED TO MATCH FUTURE NEEDS OF BUILDING.

30. CONTRACTOR SHALL INSTALL 1 INCH CONDUITS FROM PANEL LOCATIONS TO EVERY ROOM IN BUILDING

6 AND 6A. (TO INCLUDE FINISHED SPACES AND UNFINISHED SPACES) JUNSTION BOXES SHALL BE

INSTALLED IN ROOM SIDE OF LINE ALONG WITH PULL STRINGS.

31. CONTRACTOR SHALL COORDINATE DATA AND TELEPHONE ROUTINGS FROM DEPICTED LOCATIONS TO

DATA AND TELEPHONE CLOSETS.

32. EACH DATA / TELEPHONE LOCATION SHALL CONSIST OF 2 DATA AND 1 TELEPHONE JACK.

33. CONTRACTOR MAY USE EXISTING CABLE TRAY AND “J”HOOKS IF USABLE. IF NO SUPPORTS ARE

PRESSENT CONTRACTOR SHALL INSTALL AS NECESSARY.

34. ALL ROOMS SHALL HAVE OCCUPANCY SENSORS. PLACEMENT TO BE COORDINATED IN THE FIELD.

35. CONTRACTOR TO PROVIDE ELECTRONIC AS-BUILT DRAWINGS SAVED IN AUTOCAD AND PDF FORMATS.

ELECTRICAL GENERAL NOTES

DUPLEX RECEPTACLE - MOUNT 18"AFF, UNO

DUPLEX RECEPTACLE - EMERGENCY POWER

QUADRUPLEX OUTLET - MOUNT 18" AFF, UNO

DATA OUTLET - FOUR JACKS PER OUTLET - MOUNT 18"AFF, UNO

(REMOVE ALL EXISTING OUTLETS AND CABLING) - NOTE ALL NEW

CABLING TO BE CAT6A CONNECTED BACK TO

EXISTING DATA OUTLET - ALL EXISTING DATA AND ASSOCIATED

CABLEING TO BE REMOVED BACK TO 1W01

PHONE

EXIT LIGHT - CEILING MOUNTED

ELECTRICAL SYMBOLS LEGEND

DATA DATA

PHONEBLANK

ALL DATA DROPS TO

MIMIC TYPICAL DETAIL

ABOVE. ALL CABLING TO

BE CAT 6A. PHONES TO

BE VOIP SYSTEM

TYPICAL DATA DROP

th re e in c h e s o n e fo o t o n e a n d o n e h a lf in c h e s o n e fo o t o n e in c h o n e fo o t th re e q u a rt e rs in c h o n e fo o t o n e h a lf in c h o n e fo o t th re e e ig h th s in c h o n e fo o t o n e q u a rt e r in c h o n e fo o t o n e e ig h th in c h o n e fo o t

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

Veterans Health

Administration

VA FORM 08-6231

Drawing Title Project Title

Location

Date Checked Drawn

Project Number

Building Number

Drawing Number

CONSULTANTS:

Drawing # of

EHRM CERNER ADMIN SPACE

VA Health Care System Approval:

Revision: Date:

ARCHITECT/ENGINEER:

U.S. DEPARTMENT OF VETERANS AFFAIRS

VA ST. LOUIS HEALTH CARE SYSTEM

FACILITIES & ENGINEERING SERVICE

JEFFERSON BARRACKS

1 JEFFERSON BARRACKS DRIVE - ST. LOUIS, MO 63125

UNITED STATES OF AMERICA

/2

/2

:5 :1

P

M

01-E-100

ELECTRICAL PLAN

HT

CM04/22/21

657-21-711JB

CONSTRUCTION DOCUMENTS

1/8" = 1'-0"

ELEC DEMO PLAN

1/8" = 1'-0"

POWER AND DATA PLAN

01-AE-100 5

OPEN WORK

GW04

BREAK

GW05A

CONFERENCE

GW07

CONFERENCE

ROOM

GW08

OFFICE

GW09A

OFFICE

GW09

STORAGE

GW04B

FINISH SCHEDULE ABBREVIATIONS

FLOORS:

CPT CARPET

E EXISTING

LVT LUXURY VINYL TILE

BASE: (4" UNLESS NOTED OTHERWISE)

E EXISTING

RB RUBBER BASE

WALLS:

E EXISTING

GYP GYPSUM BOARD

PT PAINT

CEILING:

ACT ACOUSTICAL CEILING TILE

E EXISTING

X EXPOSED

PT PAINT

CASEWORK:

PLAM PLASTIC LAMINATE

PAINT

PT1

MFR: SHERWIN-

WILLIAMS

TYPE: PROMAR 200

COLOR; SW7008

ALABASTER

FINISH: EGGSHELL

PT2

MFR: SHERWIN-

WILLIAMS

TYPE: PROMAR 200

COLOR; SW9145

SLEEPY HOLLOW

FINISH: EGGSHELL

PT3

MFR: SHERWIN-

WILLIAMS

TYPE: PROMAR 200

COLOR; SW7757

HIGH REFLECTIVE

WHITE

FINISH: FLAT

MATERIAL LEGEND

CEILING TILE

ACT1

ARMSTRONG

FINE FISSURED

24"X48"

BASE

WALLS CEILINGS

RUBBER BASE

RB1

MFR: ROPPE

COLOR: BLACK

TYPE: 4" COVE

DOOR PAINTS

PT4 (HM FRAMES)

MFR: SHERWIN-

WILIAMS

TYPE: PRE-

WATERBASE

EPOXY

COLOR: MATCH

ADJACENT WALL

COLOR

FINISH: SATIN

MISCELLANEOUS

LUXURY VINYL TILE

LVT1

MFR: MOHAWK

GROUP

TYPE: 36" SQ. TILE

PATTERN: BOLDER

COLOR: PEBBLE

C0010/925

E

EXISTING

MATERIAL TO

REMAIN

FLOOR

CASEWORK

PLASTIC LAMINATE

PL1 (CABINETS)

MADE OF MARINE

GRADE PLYWOOD

MFR: NEVAMAR

COLOR: CLEAR

MAPLE WM8340-T

SOLID SURFACE

SS (COUNTERTOPS)

MFR: CORIAN

COLOR:

ARROWROOT

FLOORS

F1. ALL FLOORING MATERIALS TO EXTEND TO WALL UNDER OPEN CASEWORK.

MISC.

M1. ALL HOLLOW METAL DOOR FRAMES WILL BE PAINTED PT3 UNLESS OTHERWISE

NOTED.

M2. PROVIDE TRANSITION STRIP AT ALL FLOORING MATERIAL JUNCTURES. CENTER OF

TRANSITION STRIP TO BE LOCATED UNDER CENTER OF DOOR.

INTERIOR FINISH NOTES

01-AE-100 5

OPEN WORK

GW04

BREAK

GW05A

CONFERENCE

GW07

CONFERENCE

ROOM

GW08

OFFICE

GW09A

OFFICE

GW09

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2

P2 P2

P2

EXISTING MECH.

STORAGE

GW04B

PAINT EXISTING

DOOR & FRAME

PT-4

A. PROVIDE INTERIOR ROOM IDENTIFICATION AND WAYFINDING SIGNAGE THROUGHOUT THE RENEWED

AREAS. COORDINATE REQUIREMENTS W/ OWNER'S REPRESENTATIVE.

B. DISCONNECT ALL ABANDONED WIRING OF ALL TYPES AT THE OVER-CURRENT PROJECTION DEVICE.

COMPLETELY REMOVE ALL ABANDONED WIRING.

C. ALL FURNITURE SHALL BE PROVIDED AND INSTALLED BY OTHERS.

D. PAINT ALL WALLS P1 U.N.O.

GENERAL FINISH PLAN NOTES

th re e in c h e s o n e fo o t o n e a n d o n e h a lf in c h e s o n e fo o t o n e in c h o n e fo o t th re e q u a rt e rs in c h o n e fo o t o n e h a lf in c h o n e fo o t th re e e ig h th s in c h o n e fo o t o n e q u a rt e r in c h o n e fo o t o n e e ig h th in c h o n e fo o t

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

1 2 3 4 5 6 7 8 9

A

B

C

D

E

F

Veterans Health

Administration

VA FORM 08-6231

Drawing Title Project Title

Location

Date Checked Drawn

Project Number

Building Number

Drawing Number

CONSULTANTS:

Drawing # of

EHRM CERNER ADMIN SPACE

VA Health Care System Approval:

Revision: Date:

ARCHITECT/ENGINEER:

U.S. DEPARTMENT OF VETERANS AFFAIRS

VA ST. LOUIS HEALTH CARE SYSTEM

FACILITIES & ENGINEERING SERVICE

JEFFERSON BARRACKS

1 JEFFERSON BARRACKS DRIVE - ST. LOUIS, MO 63125

UNITED STATES OF AMERICA

/2

/2

:5 :1

P

M

01-AI-100

FURNITURE & FINISHES

HT

CM04/22/21

657-21-711JB

CONSTRUCTION DOCUMENTS

1/8" = 1'-0"

FFE PLAN

Finish Schedule

Number Name Floor Finish

Base Finis h East

Finish North Finish

South Finish

West Finish Ceiling Type

Ceiling Finish

GW04 OPEN WORK LVT1 RB1 SEE

PLAN

SEE

PLAN

SEE

PLAN

SEE

PLAN

ACT1 ACT1

GW08 CONFERENCE ROOM LVT1 RB1 PT1 PT1 PT1 PT2 EXIST GYP PT-3

GW09A OFFICE LVT1 RB1 PT1 PT1 PT1 PT1 ACT1 ACT1

GW09 OFFICE LVT1 RB1 PT1 PT1 PT1 PT1 ACT1 ACT1

GW05A BREAK LVT1 RB1 PT2 PT2 PT2 PT1 ACT1 ACT1

GW07 CONFERENCE LVT1 RB1 PT1 PT1 PT1 PT1 ACT1 ACT1

GW10 WAITING LVT1 RB1 PT1 PT1 PT1 PT1 ACT1 ACT1

GW04A STORAGE LVT1 RB1 PT1 PT1 PT1 PT1 EXIST GYP PT-3

H0011 CORRIDOR LVT1 RB1 PT1 PT1 PT1 PT1 ACT1 ACT1

Equipment Schedule

Item Responsible

1 MICROWAVE VV

2 REFRIGERATOR VC

3 EXHAUST FAN CC

4 PRINTERS VV

5 PHONES VV

6 FURN - SYSTEM VV-CERNER

7 FURN- BREAKROOM VV-CERNER

8 FURN-CONFERENCE VV-CERNER

1/8" = 1'-0"

FINISH PLAN

VV- PROVIDED AND INSTALLED BY VA

VV-CERNER - PROVIDED AND INSTALLED BY CERNER

CC -PROVIDED AND INSTALLED BY CONTRACTOR