36A77618Q9154-003.docx

VA Northern California Health Care System 2000 Concord Avenue Chico, CA 95928

VA Northern California Health Care System Initial Outfitting, Transition & Activation Statement of Work Pharmacy Dispensing & Storage

Approved By:

Date:

VA Northern California Health Care System 2000 Concord Avenue Chico, CA 95928

Statement of Work Pharmacy Dispensing & Storage

Introduction Veteran Affairs Northern California Health Care System (VANCHCS) has a requirement to purchase Pharmacy Dispensing & Storage with an authorized vendor to supply and deliver the item(s) identified in Table 1 below. This requirement is in support of a brand name or equal requirement. See below for salient characteristics. This requirement is in support of the activation of Chico VA Clinic.

Table 1 – Package Items Summary

Table 1 – Package Items Summary (Cont’d)

General Conditions Site Address The address of the VANCHCS Chico VA Clinic is provided below. Further information on delivery is located in section 2.4.

Chico VA Clinic 1601 Concord Avenue

Delivery Schedule Items shall be delivered no earlier than the estimated delivery start date and no later than the delivery end date listed in Table 2 below.

Table 2 – Anticipated Building Outfitting Schedule

Chico VA Clinic

Schedule and Order Management Due to the nature of activation efforts and construction, timelines and dates may vary and shift. Deliver dates need to be flexible. The delivery of items for installation are dependent upon the completion of applicable areas within the building. If there is a delay, the Contractor may be required to adjust the delivery date at no cost to the Government. The Contractor will coordinate with the onsite POC’s before delivery (see 2.4.1) The awardees actual delivery dates will be confirmed by VA upon award.

Post-award, the vendor will coordinate delivery identified in this document with the VANCHCS prior to beginning any work (See Section 2.4). Once the dates have been confirmed, modifications to the schedule are subject to written approval by the CO, COR and the vendor. Schedule changes that are beyond the dates specified in the contract will require approval by the Contracting Officer and a contract modification.

Delivery and Receiving

0. Delivery and receipt of the proposed items is anticipated to be directed to the location identified below. Confirmation of delivery location will be provided post-award. To coordinate delivery, contact Government POC Antonio Homer at (916) 843-7393, Antonio.homer@va.gov and Angela Howard at (217) 274-8933, angela.howard@goenergistics.com or Jack O’Dell at (937) 608-7329, jack.odell@goenergistics.com.

☒ VANCHCS Chico VA Clinic (Direct Delivery to address detailed in paragraph 2.1.1) ☐ IOT&A Contractor-Provided Warehouse Local to the VANCHCS Go Energistics Warehouse: Attn: GoE-VA Project, 13290 Contractor Dr., Chico, CA 95928 The delivery of items identified in this document shall take place during normal business hours which are defined as: 0800 to 1630 (i.e.: 8:00am to 4:30pm Pacific Standard Time), Monday through Friday, and excluding Federal Holidays.

Delivery trucks will not be permitted to remain at the loading dock. Trucks shall be unloaded, moved from the dock, and then brought back to the dock if required to haul out any waste, tools, or excess materials.

Labeling of delivered items shall include the VA facilities contract number and VA purchase order number for identification and reference upon receipt of product.

Use of Warehouse If the vendor requires the use of the Government’s activation contractor’s warehouse to meet the requirements of this contract the vendor must provide a certificate of insurance prior to the delivery and offloading of the item(s). This insurance certificate must be completed and presented to the activation contractor prior to delivery.

The vendor shall communicate through the VA POC any required coordination requirements.

Clean Up and Disposal There are no dumpsters available for vendor use.

The removal of waste and/or excess material shall be conducted through the loading dock area.

Deliverables The vendor shall provide CAD drawings (including shop drawings) and specifications for site prep that is required for their product as well as finish samples if requested below. Please send to:

Christina Pereira-Tequida Engineering & Facilities Management Service 10535 Hospital Way Mather, CA, 95655 Assembly and Installation The vendor is required to manage and coordinate installation at the VANCHCS Chico VA Clinic with the COR.

On-site assembly and installation of items, and performance of services identified in this document shall take place during normal business hours which are defined as: 0800 to 1630 (i.e.: 8:00am to 4:30pm Pacific Standard Time), Monday through Friday, and excluding Federal Holidays.

The vendor is required to define the need for a staging area to accommodate item assembly and installation, if needed. Post-award, this information will be confirmed with the vendor.

The vendor is required to provide tools, labor and materials to complete assembly and installation of the items detailed in this document.

The vendor shall protect all finished spaces and surfaces as required from delivery and installation damage. The vendor shall use covering and protection to the extent necessary to prevent damage to finished spaces. Any damage occurred during delivery and installation is the responsibility of the vendor. The vendor will be responsible for paying for and repairing any damage or noted deficiencies to finished spaces and surfaces that occur as a result of the vendor’s (or associated sub-contractors) installation.

During the entire duration of assembly and installation, the vendor will have a competent representative on-site as the vendor’s contact, and to serve as the interface between the vendor and VANCHCS. On-site representative can be the installer. All instructions provided from COR to the representative will be binding as if given to the vendor’s main contact. The COR may provide specific instructions, however, only the Contracting Officer may change the terms or conditions of the contract.

VA Northern California Health Care System E0609A

Project: Chico VA Clinic

Total Quantity: 1 ☒ Finish Sample Required if Checked ☒ Manufacturer Certified Installation Required if Checked ☐ BMET Training Required if Checked ☐ End User Training Required if Checked

Item Name: Shelf Unit, Pharmacy, Wall Mtd, 84"Hx36"Wx15"D

Please Note: Picture is for reference only to illustrate the general design concept:

Salient Characteristics:

Pharmacy storage shelves used to store pharmaceutical drug containers and other small containers needed throughout the pharmacy. Overall dimensions (including toe kick) 84" high x 36" wide x 15" deep.

Materials:

Core material shall be particle board conforming to CS 236-66 45 pound “B” density, Class 1 of Type 1 Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

Adhesive for laminate shall be urea-formaldehyde resin free.

Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

Shelving shall be 3/4" thick core with laminate on both sides.

Casework shall be fabricated using flush construction methods with modern machinery.

Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable.

Salient Characteristics (Cont’d):

Features Unit shall be securable to the wall via mounting hardware Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick Unit shall have non-adjustable top panel 84" above finished floor.

Unit shall have all edges finished, covered and sealed.

Unit shelves shall be adjustable at 1" increments and can be positioned either flat or slop able Unit shall have a 4" toe kick.

Unit shall have 12 adjustable shelves made from particle board with a high-pressure laminate finish Finishes

· Casing, shelves, end panels-Laminate WilsonArt – Fusion Maple 7909-60 with edge banding to match laminate

· PVC edge banding- to match laminate

· Final finishes to be approved by VA interior design prior to purchase.

VA Northern California Health Care System E0609B

Project: Chico VA Clinic

Total Quantity: 1

☐ BMET Training Required if Checked ☐ End User Training Required if Checked

Item Name: Shelves, Pharmacy Wall Mounted 30"Hx36"Wx15"D

Please Note: Picture is for reference only to illustrate the general design concept:

Salient Characteristics:

Pharmacy storage shelves with laminated countertop used to store pharmaceutical drug containers and other small containers needed throughout the pharmacy. Overall dimensions (including toe kick) 30" high x 36" wide x 15" deep.

Core material shall be particle board conforming to CS 236-66 45 pound “B” density, Class 1 of Type 1 Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

Adhesive for laminate shall be urea-formaldehyde resin free.

Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

Shelving shall be 3/4" thick core with laminate on both sides.

Casework shall be fabricated using flush construction methods with modern machinery.

Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable.

Features Unit shall be securable to the wall via mounting hardware Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick Unit shall have non-adjustable top panel 30" above finished floor.

Unit shall have all edges finished, covered and sealed.

Unit shelves shall be adjustable at 1" increments and can be positioned either flat or slop able Unit shall have a 4" toe kick.

Unit shall have 1 adjustable shelf made from particle board with a high-pressure laminate finish Finishes Countertop-Solid surface Corian or similar- Color Witch Hazel Casing, shelves, end panels-Laminate WilsonArt – Fusion Maple 7909-60 with edge banding to match laminate PVC edge banding- to match laminate Final finishes to be approved by VA interior design prior to purchase

VA Northern California Health Care System E0612A

Project: Chico VA Clinic

Total Quantity: 2

☐ BMET Training Required if Checked ☐ End User Training Required if Checked

Item Name: Shelf Unit, Pharmacy, Wall Mtd, 84"H x 31.5"W x 24"D

Please Note: Picture is for reference only to illustrate the general design concept:

Salient Characteristics:

Pharmacy storage shelves with laminated countertop used to store pharmaceutical drug containers and other small containers needed throughout the pharmacy. Overall dimensions (including toe kick) 84" high x 31.6" wide x 24" deep.

Core material shall be particle board conforming to CS 236-66 45 pound “B” density, Class 1 of Type 1 Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

Adhesive for laminate shall be urea-formaldehyde resin free.

Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

Shelving shall be 3/4" thick core with laminate on both sides.

Casework shall be fabricated using flush construction methods with modern machinery.

Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable.

Features Unit shall be securable to the wall via mounting hardware Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick Unit shall have non-adjustable top panel 84" above finished floor.

Unit shall have all edges finished, covered and sealed.

Unit shelves shall be adjustable at 1" increments and can be positioned either flat or slop able Unit shall have a 4" toe kick.

Unit shall have 12 adjustable shelves made from particle board with a high-pressure laminate finish Finishes Casing, shelves, end panels-Laminate WilsonArt – Fusion Maple 7909-60 with edge banding to match laminate

VA Northern California Health Care System E0615A

Project: Chico VA Clinic

Total Quantity: 9

☐ BMET Training Required if Checked ☐ End User Training Required if Checked

Item Name: Shelves, Pharmacy, Wall Mtd, 84"Hx36"Wx12"D

Please Note: Picture is for reference only to illustrate the general design concept:

Salient Characteristics:

Pharmacy storage shelves with laminated countertop used to store pharmaceutical drug containers and other small containers needed throughout the pharmacy. Overall dimensions (including toe kick) 84" high x 36" wide x 12" deep.

Core material shall be particle board conforming to CS 236-66 45 pound “B” density, Class 1 of Type 1 Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

Adhesive for laminate shall be urea-formaldehyde resin free.

Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

Shelving shall be 3/4" thick core with laminate on both sides.

Casework shall be fabricated using flush construction methods with modern machinery.

Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable.

Features Unit shall be securable to the wall via mounting hardware Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick Unit shall have non-adjustable top panel 84" above finished floor.

Unit shall have all edges finished, covered and sealed.

Unit shelves shall be adjustable at 1" increments and can be positioned either flat or slop able Unit shall have a 4" toe kick.

Unit shall have 12 adjustable shelves made from particle board with a high-pressure laminate finish Finishes Casing, shelves, end panels-Laminate WilsonArt – Fusion Maple 7909-60 with edge banding to match laminate

VA Northern California Health Care System E0615B

Project: Chico VA Clinic

Total Quantity: 1

☐ BMET Training Required if Checked ☐ End User Training Required if Checked

Item Name: Shelves, Pharmacy, Wall Mtd, 84"Hx30"Wx12"D

Please Note: Picture is for reference only to illustrate the general design concept:

Salient Characteristics:

Pharmacy storage shelves with laminated countertop used to store pharmaceutical drug containers and other small containers needed throughout the pharmacy. Overall dimensions (including toe kick) 84" high x 30" wide x 12" deep.

Core material shall be particle board conforming to CS 236-66 45 pound “B” density, Class 1 of Type 1 Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

Adhesive for laminate shall be urea-formaldehyde resin free.

Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

Shelving shall be 3/4" thick core with laminate on both sides.

Casework shall be fabricated using flush construction methods with modern machinery.

Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable.

Features Unit shall be securable to the wall via mounting hardware Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick Unit shall have non-adjustable top panel 84" above finished floor.

Unit shall have all edges finished, covered and sealed.

Unit shelves shall be adjustable at 1" increments and can be positioned either flat or slop able Unit shall have a 4" toe kick.

Unit shall have 12 adjustable shelves made from particle board with a high-pressure laminate finish Finishes Casing, shelves, end panels-Laminate WilsonArt – Fusion Maple 7909-60 with edge banding to match laminate

VA Northern California Health Care System E0615C

Project: Chico VA Clinic

Total Quantity: 1

☐ BMET Training Required if Checked ☐ End User Training Required if Checked

Item Name: Shelves, Pharmacy, Wall Mtd, 88"Hx24"Wx12"D

Please Note: Picture is for reference only to illustrate the general design concept:

Salient Characteristics:

Pharmacy storage shelves with laminated countertop used to store pharmaceutical drug containers and other small containers needed throughout the pharmacy. Overall dimensions (including toe kick) 84" high x 24" wide x 12" deep.

Core material shall be particle board conforming to CS 236-66 45 pound “B” density, Class 1 of Type 1 Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

Adhesive for laminate shall be urea-formaldehyde resin free.

Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

Shelving shall be 3/4" thick core with laminate on both sides.

Casework shall be fabricated using flush construction methods with modern machinery.

Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable.

Features Unit shall be securable to the wall via mounting hardware Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick Unit shall have non-adjustable top panel 84" above finished floor.

Unit shall have all edges finished, covered and sealed.

Unit shelves shall be adjustable at 1" increments and can be positioned either flat or slop able Unit shall have a 4" toe kick.

Unit shall have 12 adjustable shelves made from particle board with a high-pressure laminate finish Finishes Casing, shelves, end panels-Laminate WilsonArt – Fusion Maple 7909-60 with edge banding to match laminate

VA Northern California Health Care System E0615E

Project: Chico VA Clinic

Total Quantity: 1

☐ BMET Training Required if Checked ☐ End User Training Required if Checked

Item Name: Shelves, Pharmacy, Wall Mtd, 84"Hx29"Wx12"D

Please Note: Picture is for reference only to illustrate the general design concept:

Salient Characteristics:

Pharmacy storage shelves with laminated countertop used to store pharmaceutical drug containers and other small containers needed throughout the pharmacy. Overall dimensions (including toe kick) 84" high x 29" wide x 12" deep.

Core material shall be particle board conforming to CS 236-66 45 pound “B” density, Class 1 of Type 1 Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

Adhesive for laminate shall be urea-formaldehyde resin free.

Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

Shelving shall be 3/4" thick core with laminate on both sides.

Casework shall be fabricated using flush construction methods with modern machinery.

Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable.

Features Unit shall be securable to the wall via mounting hardware Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick Unit shall have non-adjustable top panel 84" above finished floor.

Unit shall have all edges finished, covered and sealed.

Unit shelves shall be adjustable at 1" increments and can be positioned either flat or slop able Unit shall have a 4" toe kick.

Unit shall have 12 adjustable shelves made from particle board with a high-pressure laminate finish Finishes Casing, shelves, end panels-Laminate WilsonArt – Fusion Maple 7909-60 with edge banding to match laminate

VA Northern California Health Care System E0615F

Project: Chico VA Clinic

Total Quantity: 3

☐ BMET Training Required if Checked ☐ End User Training Required if Checked

Item Name: Shelves, Pharmacy, Wall Mtd, 84"Hx35"Wx12"D

Please Note: Picture is for reference only to illustrate the general design concept:

Salient Characteristics:

Pharmacy storage shelves with laminated countertop used to store pharmaceutical drug containers and other small containers needed throughout the pharmacy. Overall dimensions (including toe kick) 84" high x 35" wide x 12" deep.

Core material shall be particle board conforming to CS 236-66 45 pound “B” density, Class 1 of Type 1 Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

Adhesive for laminate shall be urea-formaldehyde resin free.

Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

Shelving shall be 3/4" thick core with laminate on both sides.

Casework shall be fabricated using flush construction methods with modern machinery.

Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable.

Features Unit shall be securable to the wall via mounting hardware Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick Unit shall have non-adjustable top panel 84" above finished floor.

Unit shall have all edges finished, covered and sealed.

Unit shelves shall be adjustable at 1" increments and can be positioned either flat or slop able Unit shall have a 4" toe kick.

Unit shall have 12 adjustable shelves made from particle board with a high-pressure laminate finish Finishes Casing, shelves, end panels-Laminate WilsonArt – Fusion Maple 7909-60 with edge banding to match laminate

VA Northern California Health Care System E0618A

Project: Chico VA Clinic

Total Quantity: 2

☐ BMET Training Required if Checked ☐ End User Training Required if Checked

Item Name: Shelves, Pharmacy, Wall Mtd, Tall, 84"Hx36"Wx18"D

Please Note: Picture is for reference only to illustrate the general design concept:

Salient Characteristics:

Pharmacy storage shelves with laminated countertop used to store pharmaceutical drug containers and other small containers needed throughout the pharmacy. Overall dimensions (including toe kick) 84" high x 36" wide x 18" deep.

Core material shall be particle board conforming to CS 236-66 45 pound “B” density, Class 1 of Type 1 Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

Adhesive for laminate shall be urea-formaldehyde resin free.

Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

Shelving shall be 3/4" thick core with laminate on both sides.

Casework shall be fabricated using flush construction methods with modern machinery.

Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable.

Features Unit shall be securable to the wall via mounting hardware Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick Unit shall have non-adjustable top panel 84" above finished floor.

Unit shall have all edges finished, covered and sealed.

Unit shelves shall be adjustable at 1" increments and can be positioned either flat or slop able Unit shall have a 4" toe kick.

Unit shall have 12 adjustable shelves made from particle board with a high-pressure laminate finish Finishes Casing, shelves, end panels-Laminate WilsonArt – Fusion Maple 7909-60 with edge banding to match laminate

VA Northern California Health Care System E0618B

Project: Chico VA Clinic

Total Quantity: 2

☐ BMET Training Required if Checked ☐ End User Training Required if Checked

Item Name: Shelves, Pharmacy, Free Standing, Tall, 88"Hx36"Wx18"D

Please Note: Picture is for reference only to illustrate the general design concept:

Salient Characteristics:

Pharmacy storage shelves with laminated countertop used to store pharmaceutical drug containers and other small containers needed throughout the pharmacy. Overall dimensions (including toe kick) 84" high x 36" wide x 18" deep.

Core material shall be particle board conforming to CS 236-66 45 pound “B” density, Class 1 of Type 1 Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

Adhesive for laminate shall be urea-formaldehyde resin free.

Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

Shelving shall be 3/4" thick core with laminate on both sides.

Casework shall be fabricated using flush construction methods with modern machinery.

Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable.

Features Unit shall be securable to the wall via mounting hardware Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick Unit shall have non-adjustable top panel 84" above finished floor.

Unit shall have all edges finished, covered and sealed.

Unit shelves shall be adjustable at 1" increments and can be positioned either flat or slop able Unit shall have a 4" toe kick.

Unit shall have 12 adjustable shelves made from particle board with a high-pressure laminate finish Finishes Casing, shelves, end panels-Laminate WilsonArt – Fusion Maple 7909-60 with edge banding to match laminate

VA Northern California Health Care System E0665A

Project: Chico VA Clinic

Total Quantity: 1

☐ BMET Training Required if Checked ☐ End User Training Required if Checked

Item Name: Pharmacy Bulk Storage Low Volume, Narcotic Room

Please Note: Picture is for reference only to illustrate the general design concept:

Salient Characteristics:

Pharmacy storage and workstation. Unit is designed to have a working countertop with 32 3/4" open cabinetry below for the storage of large items such as trash cans and pharmaceutical waste containers. 24" of space will be dedicated for a set of 3 gravity drawers. Unit is designed with 2 sets of end panels a back panel and solid surface countertop. Unit will also include modular hospital grade duplex receptacle. Overall Dimensions: 4' 9 3/4" wide x 39" high x 24" deep Materials and construction

· Core material shall be particle board conforming to CS 236-66 45 pound “B” density, Class 1 of Type 1

· Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type.

· All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

· Adhesive for laminate shall be urea-formaldehyde resin free.

· Laminated plastic finish shall be finely textured.

· Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

· Doors and drawer fronts shall be a minimum of 13/16" thick with composed out of the same material as the cabinetry finished with high pressure laminate.

· Unit shall have self-closing drawer slides with nylon rollers

· Countertop shall run the length of the end panels and be composed out of a solid surface material. Core shall be 1-1/8" thick with 1/16" laminate finish.

· Unit shall have a 4" toe kick.

· Casework shall be fabricated using flush construction methods with modern machinery.

· Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable.

Hardware

· Hinges shall be concealed, self-closing and 3 way adjustable. They shall be constructed out of nickel plated steel with 110-degree opening

· Locks shall be multi-tumbler chrome plated brass with brass slide bolt.

Drawers

· Shall have sides that are ¾” thick. All inserts for drawers shall be interchangeable between units and self-contained. Drawers shall have full travel extension, movement on steel ball bearings with positive stop and lock in closed position.

· Drawers shall be positioned for gravity feed and include organizational inserts

· Drawer set is 3 identically sized drawers Electrical

· Raceways for electrical and communication services lines to be included where electrical and data coordination is required. Lines shall be 2” wide rib construction with 1/8” Masonite glued to both sides of ribs. Ribs shall be able to be screwed to cabinetry.

· Electrical fixtures shall be 20-amp 120 volt, 3-wire polarized grounded duplex receptacle. Fixtures shall be UL listed hospital grade receptacles.

· All fixtures, conduit or fittings shall be compliant with NFPA and NEC.

Finishes

· Countertop-Solid surface Corian or similar- Color Witch Hazel

· Casing, shelves, end panels-Laminate WilsonArt – Fusion Maple 7909-60 with edge banding to match laminate

· PVC edge banding- to match laminate

· Final finishes to be approved by VA interior design prior to purchase Unit components from left to right:

· 32 3/4" wide open space with back panel and end supports.

· 24" wide gravity drawers that are lockable.

· Solid surface countertop that runs the length of the unit and connects with E0667A Grommets for electrical cords are to be cut on-site once equipment is installed.

VA Northern California Health Care System E0665B

Project: Chico VA Clinic

Total Quantity: 1

☐ BMET Training Required if Checked ☐ End User Training Required if Checked

Item Name: Pharmacy Bulk Storage Low Volume, Island

Please Note: Picture is for reference only to illustrate the general design concept:

Salient Characteristics:

Pharmacy storage and work island. Unit is designed to have a working solid surface countertop with 24" open cabinetry below with 2 adjustable shelves and finished back. 24" of space will be dedicated for an 84" high back to back shelving unit. Each side has 12 adjustable shelves and be 12" deep. Overall Dimensions: 4' wide x 39" / 84" high x 24" deep

Core material shall be particle board conforming to CS 236-66 45 pound “B” density, Class 1 of Type 1 Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

Adhesive for laminate shall be urea-formaldehyde resin free.

Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

Countertop shall run the length of the end panels and be composed out of a solid surface material. Core shall be 1-1/8" thick with 1/16" laminate finish.

Shelving shall be 3/4" thick core with laminate on both sides.

Casework shall be fabricated using flush construction methods with modern machinery.

Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable.

Unit components from left to right:

South Side 24" open shelving with back panel and end supports. Unit has 2 adjustable shelves with solid surface countertop 24" wide slop able double-sided shelving unit. Unit contains 12 adjustable shelves 4" high toe kick North Side 24" wide slop able double-sided shelving unit. Unit contains 12 adjustable shelves Finished back panel with 39" solid surface countertop.

4" high toe kick Grommets for electrical cords are to be cut on-site once equipment is installed.

Finishes Countertop-Solid surface Corian or similar- Color Witch Hazel Casing, shelves, end panels-Laminate WilsonArt – Fusion Maple 7909-60 with edge banding to match laminate

VA Northern California Health Care System E0666A

Project: Chico VA Clinic

Total Quantity: 1

☐ BMET Training Required if Checked ☐ End User Training Required if Checked

Item Name: Workstation Prep/Pack Island

Please Note: Picture is for reference only to illustrate the general design concept:

Salient Characteristics:

Pharmacy storage and workstation. Unit is designed to have a working countertop with cabinetry below and above providing storage and space to hold equipment and supplies. Unit is a free standing two-sided island with upper counter mounted shelving, countertops and lower storage and finished end panels. Unit is designed with the following components: Secured suspended upper-case support system with adjustable and plexiglass shelving, tasking lighting, solid surface countertop, counter mounted dual monitor mounts, open under counter storage, pull out printer shelves, knee space with back panel and CPU holder, open adjustable shelving, lockable file drawers, gravity drawers and modular hospital grade duplex outlets. Cabinetry shall have 2 counter mounted finished end panels that is 50" high 30" deep x 3/4" wide. Panel to be constructed out of same material as cabinetry with matching laminate finish. Overall Dimensions: 129 3/4" wide x 84 " high x 60" deep

Core material shall be particle board conforming to CS 236-66 45 pound “B” density, Class 1 of Type 1 Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type.

All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

Adhesive for laminate shall be urea-formaldehyde resin free.

Laminated plastic finish shall be finely textured.

Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

Doors and drawer fronts shall be a minimum of 13/16" thick with composed out of the same material as the cabinetry finished with high pressure laminate.

Unit shall have self-closing drawer slides with nylon rollers Countertop shall run the length of the end panels and be composed out of a solid surface material. Core shall be 1-1/8" thick with 1/16" laminate finish.

Unit shall have a 4" toe kick.

Casework shall be fabricated using flush construction methods with modern machinery.

Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable.

Hardware Hinges shall be concealed, self-closing and 3 way adjustable. They shall be constructed out of nickel plated steel with 110 degree opening Locks shall be multi-tumbler chrome plated brass with brass slide bolt.

Shelving Suspended upper case support system adjustable shelving shall consist of 3 sections of shelving; 2 sets of plexiglass shelves and 1 set of adjustable slop able shelving.

Shelving to be constructed out of high performance particle board core with a high-pressure plastic laminate finish.

Shelves shall be ¾” thick solid core panels with reversible retainer lips Drawers Shall have sides that are ¾” thick. All inserts for drawers shall be interchangeable between units and self-contained. Drawers shall have full travel extension, movement on steel ball bearings with positive stop and lock in closed position.

Gravity Drawers Drawers shall be positioned for gravity feed and include organizational inserts Drawer set is 3 identically sized drawers Electrical Raceways for electrical and communication services lines to be included where electrical and data coordination is required. Lines shall be 2” wide rib construction with 1/8” Masonite glued to both sides of ribs. Ribs shall be able to be screwed to cabinetry.

Electrical fixtures shall be 20-amp 120 volt, 3-wire polarized grounded duplex receptacle. Fixtures shall be UL listed hospital grade receptacles.

All fixtures, conduit or fittings shall be compliant with NFPA and NEC.

Task Lighting Task light shall include mounting brackets Cabinet shall be designed with components in order from left to right:

EAST SIDE

48" wide counter mounted adjustable shelving that is 29" high and 30" deep, double sided. Shelving has adjustable 12" shelving at 1" increments. Shelving can be sloped for gravity pull s system. Unit shall include 4 adjustable shelves. Supports are mounted to the countertop, and shelving starts at 21" above the counter and are 27" high and 30" deep. Each side of the adjustable shelving has 12" wide plexiglass shelving. Plexi shelving is counter mounted and has 7 integrated shelving units. Top of suspended counter shelving system has a reveal that is 74.5" wide.

Shelving mounted to counter mounted supports that are 1 1/7" wide and constructed out of the same material as cabinetry and has the same laminate finish.

Mounted to the shelving is a 36" wide task light Pass through spacing of 21" high shall be allowed from the bottom of the task light to the top of the solid surface countertop. Countertop shall be 39" above finished floor

Below the countertop shall be a 18" wide set of file drawers. Cabinets shall be 18" wide 38" high x 26" deep. Bottom 2 drawers are file cabinets and the top drawer is smaller for supplies.

Unit shall have a 14 1/4" wide open cabinet with adjustable shelves. Cabinet shall be open facing with shelves that are adjustable at 1" increments and slop able. Unit shall be supplied with two shelves and finished back panel.

Unit shall have open space that is 15" wide for the storage of trash containers or other equipment. Space shall have leg braces and include a removable back panel. Panel shall be finished and allow for the incorporation of electrical and data drops.

Unit shall have a 27" wide cabinet with a pull-out printer drawer and a back panel. Unit will also contain an adjustable shelf. Back panel shall allow for of electrical duplex and data jack for printer hookup.

A counter mounted dual monitor mount shall be attached to the solid surface countertop. Mount shall allow for the adjustment of each monitor separately while firmly securing to the countertop.

Below the counter shall be a knee space 21 5/8"" wide with a back panel and adjustable shelf. Attached to the knee space side panel shall be a CPU holder that can accommodate 2 CPUs. Electrical duplex and data shall be accessible via the back panel.

Below the counter shall be a knee space 25 5/8"" wide with a back panel and adjustable shelf. Electrical duplex and data shall be accessible via the back panel.

WEST SIDE

48" wide counter mounted adjustable shelving that is 29" high and 30" deep, double sided. Shelving has adjustable 12" shelving at 1" increments. Shelving can be sloped for gravity pull s system. Unit shall include 4 adjustable shelves. Supports are mounted to the countertop, and shelving starts at 21" above the counter and are 27" high and 30" deep. Each side of the adjustable shelving has 12" wide plexiglass shelving. Plexi shelving is counter mounted and has 7 integrated shelving units. Top of suspended counter shelving system has a reveal that is 74.5" wide.

Shelving mounted to counter mounted supports that are 1 1/7" wide and constructed out of the same material as cabinetry and has the same laminate finish.

Mounted to the shelving is a 36" wide task light Pass through spacing of 21" high shall be allowed from the bottom of the task light to the top of the solid surface countertop. Countertop shall be 39" above finished floor Below the countertop shall be a 18" wide set of 3 gravity drawers. Cabinets shall be 18" wide 38" high x 26" deep. Drawers are of equal size and can be sloped to provide gravity pull system. Drawers will include organizational inserts.

Unit shall have a 24 1/8" wide open cabinet with adjustable shelves. Cabinet shall be open facing with shelves that are adjustable at 1" increments and slop able. Unit shall be supplied with two shelves. Unit includes back panel.

Unit shall have open space that is 15" wide for the storage of trash containers or other equipment. Space shall have leg braces and include a removable back panel. Panel shall be finished and allow for the incorporation of electrical and data drops.

Unit shall have a 27" wide cabinet with a pull-out printer drawer and a back panel. Unit will also contain an adjustable shelf. Back panel shall allow for addition of electrical and databox for printer hookup.

A counter mounted dual monitor mount shall be attached to the solid surface countertop. Mount shall allow for the adjustment of each monitor separately while firmly securing to the countertop.

Below the counter shall be a knee space 21 3/4"" wide with a back panel and adjustable shelf. Attached to the knee space side panel shall be a CPU holder that can accommodate 2 CPUs. Electrical duplex and data shall be accessible via the back panel.

Below the countertop shall be a 18" wide set of 3 gravity drawers. Cabinets shall be 18" wide 38" high x 30" deep. Drawers are of equal size and can be sloped to provide gravity pull system. Drawers will include organizational inserts.

Unit shall have a toe kick except for the location of the knee space and open storage. Countertop shall be 39" above finished floor. Solid surface countertop shall run the length of the unit to the base end panels. The counter shall be the length of the island and 60" wide, the width of the island Grommet holes to be drilled on site after installation of equipment for proper coordination Finishes Countertop-Solid surface Corian or similar- Color Witch Hazel Casing, shelves, end panels-Laminate WilsonArt – Fusion Maple 7909-60 with edge banding to match laminate

VA Northern California Health Care System E0666B

Project: Chico VA Clinic

Total Quantity: 1

☐ BMET Training Required if Checked ☐ End User Training Required if Checked

Item Name: Workstation, Pharmacist, Triple

Please Note: Picture is for reference only to illustrate the general design concept:

Salient Characteristics:

Pharmacy workstation for 3 people. Unit is designed to have a working height countertop with cabinetry below and above providing storage and space to hold equipment and supplies. Unit is designed with the following components: Lockable wall mounted cabinets with doors, tasking lighting, solid surface countertop, counter mounted dual monitor mount, knee space with back panel and CPU holder and a set of lockable file drawers. Unit also includes Hospital grade electrical duplex outlets. Overall Dimensions: 12' wide x 84 " high x 28" deep

Core material shall be particle board conforming to CS 236-66 45 pound “B” density, Class 1 of Type 1 Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type.

All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

Adhesive for laminate shall be urea-formaldehyde resin free.

Laminated plastic finish shall be finely textured.

Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

Doors and drawer fronts shall be a minimum of 13/16" thick with composed out of the same material as the cabinetry finished with high pressure laminate.

Unit shall have self-closing drawer slides with nylon rollers Countertop shall run the length of the end panels and be composed out of a solid surface material. Core shall be 1-1/8" thick with 1/16" laminate finish.

Unit shall have a 4" toe kick.

Casework shall be fabricated using flush construction methods with modern machinery.

Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable Hardware Hinges shall be concealed, self-closing and 3 way adjustable. They shall be constructed out of nickel plated steel with 110 degree opening Locks shall be multi-tumbler chrome plated brass with brass slide bolt.

Shelving Shelves shall be ¾” thick solid core panels with reversible retainer lips Wall mounted adjustable shelving shall consists of 3 sections of shelving with each set having 1 adjustable and removable…