Remanufacture of the F100-PW-220/-220E/-229 Carbon Seals
Synopsis for FA8121-19-R-0019 AFSC/PZAAA, 3001 STAFF DR, STE 1AE1/98C, TINKER AFB, OK 73145-3032 Remanufacture of the F100-PW-220/-220E/-229 Carbon Seals 1. Estimated issue date: 13 May 2019 Estimated closing/response date: 12 June 2019 2. PR#: FD2030-19-00011 (USAF) and FD2030-18-34081 (FMS) 3. This is a remanufacturing requirement and will be a Requirements contract with a one (1)-year base and four (4), one (1)-year options. 4. RMC - R1C 5. NSN and Output Part Number(s): (see below) The NSN and part numbers listed below are also applicable to all of the subsequent option years. USAF CLIN 0001 - #1 Carbon Seal, NSN: 2840-00-352-2148NZ P/N: 4031515 (IC), 4031516, 4031517 CLIN 0002-- #2 Carbon Seal (rear), NSN: 2840-00-343-7692NZ P/N: 4033286 (IC), 4033283, 4033284 CLIN 0003-- #2 Carbon Seal (front), NSN 2840-01-282-4202NZ P/N: 4074010 (IC), 4072837, 4072839 CLIN 0004-- #3 Carbon Seal (rear), NSN 2840-00-570-0752NZ P/N: 4036995, 4036993, 4036994 CLIN 0005--#3 Carbon Seal (front), NSN: 2840-00-343-7601NZ P/N: 4018381 (IC), 4012468, 4012501 CLIN 0006--#4 Carbon Seal, NSN: 2840-00-390-1162NZ and 2840-01-386-9284NZ P/N: 4035886 (IC), 4035883, 4035882 CLIN 0007--#5 Carbon Seal, NSN 2840-00-340-7343NZ P/N: 4018382 (IC), 4014756, 4014757 FMS CLIN 0009 - #1 Carbon Seal, NSN: 2840-00-352-2148NZ P/N: 4031515, 4031516, 4031517 CLIN 0010-- #2 Carbon Seal, NSN: 2840-00-343-7692NZ P/N: 4033286, 4033283, 4033284 CLIN 0011-- #2 Carbon Seal, NSN 2840-01-282-4202NZ P/N: 4074010, 4072837, 4072839 CLIN 0012-- #3 Carbon Seal, NSN 2840-00-570-0752NZ P/N: 4036995, 4036993, 4036994 CLIN 0013--#3 Carbon Seal, NSN: 2840-00-343-7601NZ P/N: 4018381, 4012468, 4012501 CLIN 0014--#4 Carbon Seal, NSN: 2840-00-390-1162NZ P/N: 4035886, 4035883, 4035882 CLIN 0015--#5 Carbon Seal, NSN 2840-00-340-7343NZ P/N: 4018382, 4014756, 4014757 6. Part Number(s): (see number 5 above) 7. Description: CLIN 0001: fit on the F100-220/220E engine inlet fan case bearing housing; CLIN 0002: #2 bearing face seal maintains the seal to contain the oil in the #2 and #3 bearing compartment of the core module rear compressor; CLIN 0003: maintains the seal to contain the oil in the compartment; CLIN 0004: a component part of #3 bearing rear seal assembly and support core module rear compressor; CLIN 0005: #3 bearing front face seal maintains the seal to contain the oil in the bearing compartment of core module rear compressor; CLIN 0006: carbon face seal maintains the seal to contain the oil in the #4 bearing area of the core module rear compressor rear hub; CLIN 0007: creates a seal containing that contains the engine oil for supply to the #5 bearing in the Fan Drive Turbine Module 8. Quantity/Delivery: (Best Estimated Quantity and delivery are below) USAF CLIN 0001 - Basic: 60 ea, Option I: 60 ea, Option II: 60 ea, Option III: 60 ea, Option IV: 60 ea, Delivery: 11 ea/month starting 30 days after receipt of order and will continue at that rate until contract is complete CLIN 0002 -Basic: 60 ea, Option I: 60 ea, Option II: 60 ea, Option III: 60 ea, Option IV: 60 ea, Delivery: 8 ea/month starting 30 days after receipt of order and will continue at that rate until contract is complete CLIN 0003 - Basic: 40 ea, Option I: 40 ea, Option II: 40 ea, Option III: 40 ea, Option IV: 40 ea, Delivery: 15 ea/month starting 30 days after receipt of order and will continue at that rate until contract is complete CLIN 0004 - Basic: 75 ea, Option I: 75 ea, Option II: 75 ea, Option III: 75 ea, Option IV: 75 ea, Delivery: 10 ea/month starting 30 days after receipt of order and will continue at that rate until contract is complete CLIN 0005 - Basic: 45 ea, Option I: 45 ea, Option II: 45 ea, Option III: 45 ea, Option IV: 45 ea, Delivery: 8 ea/month starting 30 days after receipt of order and will continue at that rate until contract is complete CLIN 0006 - Basic: 170 ea, Option I: 170 ea, Option II: 170 ea, Option III: 170 ea, Option IV: 170 ea, Delivery: 17 ea/month starting 30 days after receipt of order and will continue at that rate until contract is complete CLIN 0007 - Basic: 45 ea, Option I: 45 ea, Option II: 45 ea, Option III: 45 ea, Option IV: 45 ea, Delivery: 8 ea/month starting 30 days after receipt of order and will continue at that rate until contract is complete CLIN 0008 - Data not separately priced FMS CLIN 0009 - Basic: 5 ea, Option I: 5 ea, Option II: 5 ea, Option III: 5 ea, Option IV: 5 ea, Delivery: 1 ea/month starting 30 days after receipt of order and will continue at that rate until contract is complete CLIN 0010 - Basic: 2 ea, Option I: 2 ea, Option II: 2 ea, Option III: 2 ea, Option IV: 2 ea, Delivery: 1 ea/month starting 30 days after receipt of order and will continue at that rate until contract is complete CLIN 0011 - Basic: 2 ea, Option I: 2 ea, Option II: 2 ea, Option III: 2 ea, Option IV: 2 ea, Delivery: 1 ea/month starting 30 days after receipt of order and will continue at that rate until contract is complete CLIN 0012 - Basic: 2 ea, Option I: 2 ea, Option II: 2 ea, Option III: 2 ea, Option IV: 2 ea, Delivery: 1 ea/month starting 30 days after receipt of order and will continue at that rate until contract is complete CLIN 0013 - Basic: 2 ea, Option I: 2 ea, Option II: 2 ea, Option III: 2 ea, Option IV: 2 ea, Delivery: 1 ea/month starting 30 days after receipt of order and will continue at that rate until contract is complete CLIN 0014 -Basic: 2 ea, Option I: 2 ea, Option II: 2 ea, Option III: 2 ea, Option IV: 2 ea, Delivery: 1 ea/month starting 30 days after receipt of order and will continue at that rate until contract is complete CLIN 0015 - Basic: 2 ea, Option I: 2 ea, Option II: 2 ea, Option III: 2 ea, Option IV: 2 ea, Delivery: 1 ea/month starting 30 days after receipt of order and will continue at that rate until contract is complete CLIN 0016 - Data not separately priced 9. Application: F100 Engine - remanufacture of the F100-220/229 Carbon Seals 10. Destination: Tinker AFB OK-USAF; To Be Determined-FMS 11. Export Control: Yes 12. UID: If unit price exceeds $5,000 then UID requirements will apply. 13. Qualification Requirements: Sources must be qualified prior to being considered for award. To be eligible for contract award, the offeror must be an approved source IAW FAR 52.209-1, Qualification Requirements. The Government is not required to delay contract award to review pending Source Approval Requests (SARs). Therefore, offerors are encouraged to submit SARs as soon as possible. If the Government has not completed review of a SAR when the contract is awarded, the SAR will be retained and the source will be reviewed as a possible source for future awards 14. Additional Information: 10 U.S.C. 2304 (c) (1), Justification: Supplies (or services) required are available from one or only a limited number of source(s) and no other type of supplies or services will satisfy agency requirements. All responsible sources may submit a capability statement, proposal or quotation, which shall be considered by the agency. Intended source is PAS Technologies. Note: An Ombudsman has been appointed to hear concerns from offerors or potential offerors during the proposal development phase of this acquisition. The purpose of the Ombudsman is not to diminish the authority of the program director or contracting officer, but to communicate contractor concerns, issues, disagreements, and recommendations to the appropriate government personnel. When requested, the Ombudsman will maintain strict confidentiality as to source of the concern. The Ombudsman does not participate in the evaluation of proposals or in the source selection process. Interested parties are invited to call the Ombudsman at (405) 736-3273. DO NOT CALL THIS NUMBER FOR SOLICITATION REQUESTS. The Government is not using the policies contained in Part 12, Acquisition of Commercial Items, in its solicitation for the described supplies or services. However, interested persons may identify to the contracting officer their interest and capability to satisfy the Government's requirement with a commercial item within 15 days of this notice Electronic procedures will be used for this solicitation. Hardcopies of the solicitation will not be sent from this office. The solicitation will be available for download only at www.fedbizopps.gov. 15. This is NOT a small business set-aside. 16. Buyer Name, Phone Number and E-mail Address: Nicole Myers, 405-739-4340, nicole.myers.1@us.af.mil. .
FA8121-19-R-0019 Department of the Air Force Materiel Command Lifecycle Management Center Tinker Air Force Base
4/26/19, 3:21 PM Remanufacture of F100-PW 229 Aircraft Carbon Seals
The Air Force Sustainment Center (AFSC) located at Tinker AFB, Oklahoma City, OK, intends to procure the Remanufacture of the items listed below on a FFP Requirements contract that will include a Basic year and four 1-yr Options. This is a Sole Source acquisition. 1. Solicitation #: FA8121-19-R-0019 2 The estimated issue/closing date for the solicitation: 9 August 2019, closes 9 September 2019 at 12 PM (CST). 3. Item: F100-PW-229 Aircraft Carbon Seals 4. RMC/RMSC: R1/C 5. Application: F100-PW-229 Engine 6. Qualification Requirements: Sources must be qualified prior to being considered for award. To be eligible for contract award, the offeror must be an approved source IAW FAR 52.209-1, Qualification Requirements. The Government is not required to delay contract award to review pending Source Approval Requests (SARs). Therefore, offerors are encouraged to submit SARs as soon as possible. If the Government has not completed review of a SAR when the contract is awarded, the SAR will be retained and the source will be reviewed as a possible source for future awards. 7. Export Control: Yes 8. Destination: USAF: Tinker AFB, OK; FMS: To Be Determined 9. Mandatory Language: NA 10. Set-aside status: Not Set-aside 11. Additional Information: Based upon market research, the Government is using the policies contained in FAR Part 15, Contract by Negotiation in it's solicitation for the described remanufacture. Authority: 10 U.S.C. 2304 (c)(1), Justification: Supplies (or services) required are available from one or a limited number of source(s) and no type of supplies or services will satisfy agency requirements. All responsible sources may submit a capability statement, proposal or quotation, which shall be considered by the agency. The current source is PAS Technologies, CAGE 4GMJ6 who is an approved source. NOTE - An Ombudsman has been appointed to hear concerns from Offerors or potential Offerors during the proposal development phase of this acquisition. The purpose of the Ombudsman is not to diminish the authority of the program director or Contracting Officer, but to communicate contractor concerns, issues, disagreements, and recommendations to the appropriate government personnel. When requested, the Ombudsman will maintain strict confidentiality as to source of concern. The Ombudsman does not participate in the evaluation of proposals or in the source selection process. Interested parties are invited to call the Ombudsman at (405) 736-3273. DO NOT CALL THIS NUMBER FOR SOLICITATION REQUESTS. 12. UID: If the unit price exceeds $5,000.00, then UID requirements will apply 13. Contracting office address: 3001 Staff DR STE 1AF1 98C, Tinker AFB, OK 73145 14. Buyer name, phone # email address: Nicole Myers 405-734-4340, nicole.myers.1@us.af.mil. Electronic procedures will be used for this solicitation. Hard copies of the solicitation will not be sent from this office. The solicitation will be available for download only at fedbizopps.gov after the solicitation is issued..
FA812119R0019 Department of the Air Force Materiel Command Lifecycle Management Center Tinker Air Force Base
8/9/19, 11:31 AM