CABLE ASSEMBLY
NSN 1H-5995-012683032, TDP VER 028, QTY 20 EA, DELIVERY FOB ORIGIN. This synopsis is for the anticipated PROCUREMENT of 20 each NSN: 5995 012683032in accordance with Reference number 5893731. This NSN will require ISO9001 Higher Level Inspection. This part requires engineering source approval by the design control activity in order to maintain the quality of the part. Existing unique design capability, engineering skills, and manufacturing/repair knowledge by the qualified source(s) require acquisition/repair of the part from the approved source(s). The approved source(s) retain data rights, manufacturing/repair knowledge, or technical data that are not economically available to the Government, and the data or knowledge is essential to maintaining the quality of the part. An alternate source must qualify in accordance with the design control activity's procedures, as approved by the cognizant Government engineering activity. The qualification procedures must be approved by the Government engineering activity having jurisdiction over the part in the intended application.The proposed acquisition is 100% set aside for small business concerns (see FAR clause 52.219-6, Notice of Total Small Business Set-Aside). The specific type of set-aside will be addressed in the solicitation tough inclusion of one of the appropriate clauses listed here: FAR 52.219-3 Notice of HUBZone Set-Aside or Sole Source Award FAR 52.219-27 Notice of Service-Disabled Veteran-Owned Small Business Set-Aside FAR 52.219-29 Notice of Set-Aside for Economically Disadvantaged Women-Owned Small Business Concerns FAR 52.219-30 Notice of Set-Aside for Women-Owned Small Business Concerns Eligible Under the Women-Owned Small Business Program DFARS 252.226-7000 Notice of Historically Black College or University and Minority Institution Set-AsideInterested parties may obtain copies of Military and Federal Specifications and Standards, Qualified Products Lists (QPLs), Qualified Product Databases (QPDs), Military Handbooks, and other standardized documents from the DoD Single Stock Point (DODSSP) at Document Automation and Production Service (DAPS) in Philadelphia, PA. NOTE: Patterns, Drawings, Deviation Lists, Purchase Descriptions, etc. are NOT stocked at DODSSP. Most documents are available in Adobe PDF format from ASSIST-Online at: http://quicksearch.dla.mil/. Users may use ASSIST-Quick Search to search for and download available documents directly using standard browser software. Documents that are not available for downloading from ASSIST-Quick Search can be ordered from the DODSSP website using the ASSIST Shopping Wizard after obtaining a DODSSP Customer Account by following the registration procedures. Users who do not have access to the internet may contact the DODSSP ASSIST Help Desk at 215-697-6396 (DSN: 442-6396), or mail their request to DLA Document Services, Bldg. 4/D, 700 Robbins Avenue, Philadelphia PA 19111-5094. Award will be made only if the offeror, the product/service, or the manufacturer meets the qualification requirement(s) at time of award, in accordance with FAR clause 52.209-1. The solicitation identifies the office where additional information can be obtained concerning qualification requirements and is cited in each individual solicitation.Based upon market research, the Government is not using the policies contained in FAR Part 12, Acquisition of Commercial Items, in its solicitation for the described supplies or services. However, interested persons may identify to the contracting officer their interest and capability to satisfy the Government's requirement with a commercial item within 15 days of this notice.
N0010422QND73 Department of the Navy Naval Supply Systems Command
4/28/22, 7:05 AM CABLE ASSEMBLY
CONTACT INFORMATION|4|N744.11|CFA|717-605-7296|rachel.e.snyder@navy.mil| ITEM UNIQUE IDENTIFICATION AND VALUATION (MAR 2022)|19|||||||||||||||||||| HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (NAVICP REVIEW FEB 1991)(FEB 1999)|1|ISO9001, please reference TDP| INSPECTION OF SUPPLIES--FIXED-PRICE (AUG 1996)|2||| WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (DEC 2018)|16|COMBO INVOICE AND RECEIVING||TBD|N00104|TBD|TBD|See Schedule|TBD|||TBD|||||| NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|1|WSS| EQUAL OPPORTUNITY (SEP 2016)|2||| WARRANTY OF DATA--BASIC (MAR 2014)|2||| FIRST ARTICLE APPROVAL--CONTRACTOR TESTING (SEP 1989)|10|FAT details are included in the drawing|||100|NAVSUP Weapon Systems Support Mech|||||| BUY AMERICAN --FREE TRADE AGREEMENTS--BALANCE OF PAYMENTS PROGRAM - BASIC(DEVIATION 2020-O0019) (MAR 2022))|3|||| NOTICE OF TOTAL SMALL BUSINESS SET-ASIDE (OCT 2020)(DEVIATION 2020-O0008)|1|| ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (NOV 2020)|13|||||||||||||| BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE (DEVIATION 2020-O0019) (JUL 2020))|3|||| BUY AMERICAN-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (NOV 2014)|1|| ANNUAL REPRESENTATIONS AND CERTIFICATIONS (JAN 2022)|13|335931|500|||||||||||| NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PERPARDENESS, AND ENRGY PROGAM USE (APRIL 2008))|2||X| EVALUATION OF FIRST ARTICLE TESTING|3|||X| EVALUATION CRITERIA AND BASIS FOR AWARD-|1|| 1. This solicitation is for the PROCUREMENT of 20 each NSN: 5995 012683032 in accordance with reference number 5893731. 2. Government-Source Inspection and Acceptance (G-S I&A) is required. If the G-S I&A will occur at a different CAGE from the Admin Award CAGE, please provide the procurement facility CAGE and/or packaging CAGE with the quote. 3. Please provide the following information in the procurement quote: Your CAGE (used as the awardee CAGE):___________________ the unit procurement price: $____________________________________ (And whether this price is firm-fixed price (FFP) _____; or not-to-exceed (NTE)______ The procurement CAGE _____________ and packaging CAGE___________ (as described in #2). Procurement Acquisition Time, delivered in _____ days. NOTE TO DISTRIBUTORS/DEALERS: IF YOU ARE A DISTRIBUTOR, YOUR QUOTATION MUST BE ACCOMPANIED WITH A LETTER FROM THE ACTUAL MANUFACTURER INDICATING THAT YOU ARE AN "AUTHORIZED" DISTRIBUTOR. IF YOU ARE A DEALER, YOUR QUOTATION MUST BE ACCOMPANIED WITH A STATEMENT CLEARLY IDENTIFYING YOUR FIRM AS A DEALER ALONG WITH THE OEM'S NAME/CAGE CODE AND P/N THAT YOU INTEND ON PROVIDING. PLEASE NOTE THE FOLLOWING WHEN GENERATING YOUR QUOTE: We are requesting that the quotes validity extend for 8 months from the submittted proposal date. 5. All contractual documents (i.e. contracts, purchase orders, task orders, delivery orders and modifications)related to the instant procurement are considered to be "issued" by the Government when copies are either deposited in the mail, transmitted by facsimile, or sent by other electronic commerce methods, such as email. The Government's acceptance of the contractor's proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein. 6. Please submit a procurement quote to Rachel Snyder via email: RACHEL.E.SNYDER@NAVY.MIL. This is the only submission method authorized. 7. Please direct questions regarding this solicitation to the person listed above (#6). 8. The resultant award of this solicitation will be issued bilaterally, requiring the contractors written acceptance prior to execution. 9. Please note this requirement has First Article Test requirements. 10. Please note this requirement has Production Lot Test requirements. SEE SEC E PARA 4 for FAT and PLT Requirements. Please refer to Form 1423, Data Item A001, which is the First Article Test Report. 1. SCOPE 1.1 This contract/purchase order contains the requirements for manufacture and the contract quality requirements for the CABLE ASSEMBLY . 2. APPLICABLE DOCUMENTS 2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions. 2.1.1 Documents, drawings, and publications supplied are listed under "Drawing Number". These items should be retained until an award is made. 2.1.2 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order. 2.2 Order of Precedence - In the event of a conflict between the text of this contract/purchase order and the references and/or drawings cited herein, the text of this contract/purchase order shall take precedence. Nothing in this contract/purchase order, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. DRAWING DATA=WS15252 |53711| G| |D|0001 | |49998|0060922 DRAWING DATA=2507660 |10001| J|FN |D|0001 | J|49998|0087605 DRAWING DATA=2508944 |10001| E|FN |D|0001 | E|49998|0054545 DRAWING DATA=5727489 |53711| R|FN |D|0001 | R|49998|0196266 DRAWING DATA=5727490 |53711| Y|FN |D|0001 | Y|49998|0345813 DRAWING DATA=5893731 |53711| Y| |D|0001 | |49998|0198207 DRAWING DATA=5893731 |53711| V|PL |D|0001 | V|49998|0029568 DRAWING DATA=5894148 |53711| J|DOC|D|0001 | |49998|0213481 DRAWING DATA=5905602 |53711| C|FN |D|0001 | C|49998|0051456 DRAWING DATA=5906219 |53711| B|FN |D|0001 | B|49998|0039695 DRAWING DATA=5906219 |53711| B|FN |D|0002 | B|49998|0021894 DRAWING DATA=5906219 |53711| B|FN |D|0003 | B|49998|0016997 DRAWING DATA=5906555 |53711| G| |D|0001 | |49998|0273301 DRAWING DATA=5906555 |53711| G|FN |D|0001 | |49998|0273323 DRAWING DATA=5906556 |53711| B|FN |D|0001 | B|49998|0052778 DRAWING DATA=6105237 |53711| F|FN |D|0001 | F|49998|0073342 DRAWING DATA=6105242 |53711| D|FN |D|0001 | D|49998|0063201 DRAWING DATA=6105305 |53711| A| |D|0001 | A|49998|0049551 DRAWING DATA=6105305 |53711| B|FN |D|0001 | B|49998|0048369 DRAWING DATA=6105311 |53711| D|FN |D|0001 | |49998|0059804 DRAWING DATA=6105312 |53711| D|FN |D|0001 | |49998|0060032 DRAWING DATA=6105313 |53711| F|FN |D|0001 | |49998|0081939 DRAWING DATA=6105314 |53711| E|FN |D|0001 | |49998|0067116 DRAWING DATA=6105315 |53711| E|FN |D|0001 | |49998|0069468 DRAWING DATA=6105316 |53711| F|FN |D|0001 | |49998|0063173 DRAWING DATA=6105317 |53711| D|FN |D|0001 | |49998|0059789 DRAWING DATA=6105318 |53711| D|FN |D|0001 | |49998|0063558 DRAWING DATA=6105320 |53711| E|FN |D|0001 | |49998|0065444 DRAWING DATA=6105321 |53711| F|FN |D|0001 | |49998|0072768 DRAWING DATA=6105322 |53711| E|FN |D|0001 | |49998|0066748 DRAWING DATA=6105323 |53711| C|FN |D|0001 | C|49998|0060916 DRAWING DATA=6105330 |53711| E|FN |D|0001 | E|49998|0057745 DRAWING DATA=6105361 |53711| D|FN |D|0001 | D|49998|0057842 DRAWING DATA=6105374 |53711| C|FN |D|0001 | C|49998|0052882 DRAWING DATA=6239880 |53711| A| |D|0001 | A|49998|0098129 DRAWING DATA=6239880 |53711| C|FN |D|0001 | C|49998|0181784 DRAWING DATA=6239881 |53711| A|FN |D|0001 | A|49998|0038710 DRAWING DATA=6239881 |53711| A|FN |D|0002 | A|49998|0025455 DRAWING DATA=6239881 |53711| A|FN |D|0003 | A|49998|0029623 DRAWING DATA=6239881 |53711| A|FN |D|0004 | A|49998|0022958 DRAWING DATA=6239881 |53711| A|FN |D|0005 | A|49998|0026582 DRAWING DATA=6239881 |53711| A|FN |D|0006 | A|49998|0025696 DRAWING DATA=6239881 |53711| A|FN |D|0007 | A|49998|0027845 DRAWING DATA=6239881 |53711| A|FN |D|0008 | A|49998|0022382 DRAWING DATA=6239882 |53711| A|FN |D|0001 | A|49998|0038669 DRAWING DATA=6239882 |53711| A|FN |D|0002 | A|49998|0026068 DRAWING DATA=6239882 |53711| A|FN |D|0003 | A|49998|0027259 DRAWING DATA=6239882 |53711| A|FN |D|0004 | A|49998|0029032 DRAWING DATA=6300628 |53711| A|FN |D|0001 | A|49998|0040149 DRAWING DATA=6300628 |53711| A|FN |D|0002 | A|49998|0019192 DRAWING DATA=6300628 |53711| A|FN |D|0003 | A|49998|0021973 DRAWING DATA=6370928 |53711| A|FN |D|0001 | A|49998|0113604 DRAWING DATA=6370928 |53711| A|FN |D|0002 | A|49998|0073756 DRAWING DATA=6370928 |53711| A|FN |D|0003 | A|49998|0087005 DRAWING DATA=6370928 |53711| A|FN |D|0004 | A|49998|0074493 DRAWING DATA=6370928 |53711| A|FN |D|0005 | A|49998|0089297 DRAWING DATA=6370928 |53711| A|FN |D|0006 | A|49998|0085026 DRAWING DATA=6370928 |53711| A|FN |D|0007 | A|49998|0074676 DRAWING DATA=6370928 |53711| A|FN |D|0008 | A|49998|0036940 DRAWING DATA=6657093 |53711| A|FN |D|0001 | A|49998|0071141 DOCUMENT REF DATA=MIL-STD-129 | | |P |041029|A| |03| DOCUMENT REF DATA=ISO9001 | | | |010417|A| | | 3. REQUIREMENTS 3.1 Design, Manufacture, and Performance - Except as modified herein, the CABLE ASSEMBLY furnished under this contract/purchase order shall meet the design, manufacture, and performance requirements specified on drawing ;5893731; cage ;0F1X1 63127 53711; . 3.2 Marking - This item shall be physically identified in accordance with ;MIL-STD-129; . 3.3 Configuration Control - MIL-STD-973 entitled "Configuration Management", Paragraph 5.4.8, Configuration Control (Short Form Procedure), is hereby incorporated. The Contractor shall submit all Engineering Change Proposals in accordance with MIL-STD-973, Paragraph 5.4.8.2 and Appendix D. Requests for Deviations shall be processed in accordance with MIL-STD-973, Paragraph 5.4.8.3 and Appendix E. Requests for Waivers shall be processed in accordance with MIL-STD-973, Paragraph 5.4.8.4 and Appendix E. (Original and two copies shall be submitted to Contracting Officer, NAVICP-MECH, P. O. Box 2020, Mechanicsburg Pa. 17055-0788.) 3.3.1 Configuration Control - When the Contractor has received authorization on a prior contract for the same NSN for the use of a drawing of a later revision status, that authorization is hereby extended to all succeeding contracts/purchase orders until another drawing revision is approved. The Contractor will notify the PCO of this occurrence in each instance, in the response to the solicitation. Such notification shall be in writing setting forth the contract under which the prior authorization was granted, the date of the granting of the authorization, and the name of the granting authority. Contractors shall also refer technical inquiries (other than those covered by MIL-STD-973) on company letterhead signed by a responsible company official, with copies distributed as stated below. The original and two copies of all Contractor generated correspondence regarding configuration shall be submitted to Contracting Officer, NAVICP-MECH, P.O. Box 2020, Mechanicsburg, PA 17055-0788. Contractors are cautioned that implementing engineering changes, waivers, deviations or technical inquiries into the contract/purchase order without approval of the Contracting Officer will be at the sole risk of the Contractor. 3.4 Mercury Free - The material supplied under this contract/purchase order is intended for use on submarines/surface ships and therefore shall contain no metallic mercury and shall be free from mercury contamination. Mercury contamination of the material will be cause for rejection. If the inclusion of metallic mercury is required as a functional part of the material furnished under this contract, the Contractor shall obtain written approval from the Procurement Contracting Officer before proceeding with manufacture. The contractor's request shall explain in detail the requirements for mercury, identify specifically the parts to contain mercury, and explain the method of protection against mercury escape. Such a request will be forwarded directly to the Procurement Contracting Officer with a copy to the applicable Government Inspector. Upon approval by the Contracting Officer, the vendor will provide a "Warning Plate" stating that metallic mercury is a functional part of the item and will include name and location of that part. The use of mercury, mercury compounds, or mercury-bearing instruments and/or equipment in a manner which might cause contamination in the manufacture, assembly, or test of material on this contract is prohibited. The most probable causes of contamination are direct-connected manometers, mercury vacuum pumps, mercury seals, or the handling of mercury in the immediate vicinity. Mercury switches, mercury in glass thermometers, standard cells and other items containing mercury may be used if they are located so as not to constitute a contamination hazard. If external contamination by metallic mercury occurs or is suspected, the following test may be used to determine whether contamination by metallic mercury exists or whether corrective cleaning measures have been effective. Enclose the equipment in a polyethylene bag or close-fitting airtight container for eight hours at room temperature (70 degrees F minimum).Sample the trapped air and if mercury vapor concentration is 0.01 mg/cu meter or more, the material is mercury contaminated insofar as the requirements of this contract are concerned. These requirements shall be included in any subcontract or purchase order hereunder and the Contractor shall insure SubContractor compliance with these requirements. Technical questions pertaining to these requirements shall be referred to the Procurement Contracting Officer via the cognizant Administrative Contracting Officer. For background, the following information is provided: Mercury is corrosive to gold, silver, nickel, stainless steels, aluminum and copper alloys. Stainless steels, nickel, and copper alloys are widely used in reactor plants and other submarine/surface ship systems. Accidental trapping of mercury in a component could cause serious damage to vital parts. Mercury is also toxic if inhaled, ingested, or absorbed tough the skin. It is evident that grave consequences could result from small amounts of mercury vapor present in an unreplenished submarine/surface ship atmosphere. 3.5 First Article Approval (Contractor Testing) - First Article Test (FAT) and approval is required. 3.6 Serialization - The supplier shall mark a serial number on each CABLE ASSEMBLY in accordance with ;IWA DWG 5893731 REV. "W" NOTE 24 contracts is prohibited unless authorized by the NAVUNSEAWARCENDIV.; . Actual serial numbers will be assigned ;Obtain serial number from Commander Naval Undersea Warfare Center. Send request to NUWC_NPT_SerialNumbers@navy.mil; . 3.7 Production Lot Approval (Contractor Testing) - Production Lot Test and approval is required. 3.8 Marking - This assembly and its piece parts shall be physically identified in accordance with MIL-STD-130. 3.9 ;Referenced in the fabrication specification 5894148 Rev J, is drawing 5759651 that requires a DD254.; 3.10 ;Shock/Vibration test is required IAW DWG 5894148 rev J.Sections 3.2.3.1 and 3.2.3.2. ; 3.11 ;IAW DWG 6105323 CABLE JACKETS ALL TYPE II CABLE ASSEMBLIES SHALL BE PROVIDED WITH JACKETS OVER THE LENGTH OF THE CABLE FOR PROTECTION AGAINST THE ENVIRONMENTAL CONDITIONS IMPOSED. THE JACKETING COMPOUND SHALL BE AN EXTRUDED POL YOLEFIN MATERIAL FORMULATED TO MEET PROPERTIES.; 4. QUALITY ASSURANCE 4.1 Responsibility for Inspection - Unless otherwise specified in the contract/purchase order, the Contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract/purchase order, the Contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 Inspection System Requirements - The supplier shall provide and maintain an inspection system acceptable to the Governmnet. The inspection system requirements shall be in accordance with MIL-I-45208. 4.3 Responsibility for Compliance - All items must meet all requirements of this contract/purchase order. The inspection set forth in this specification shall become a part of the Contractor's overall inspection system or quality program. The absence of any inspection requirements shall not relieve the Contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract/purchase order. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, not does it commit the Government to acceptance of defective material. 4.4 Records of Inspection - (This requirement is not applicable to Government Purchase Orders) Records of all inspection work performed by the Contractor, as referenced elsewhere in this contract, shall be kept complete and available to the Government during the performance of the contract and for a period of four years after final delivery of supplies. 4.5 First Article Test/Inspection (Contractor) - The Contractor shall conduct ;The Contractor shall conduct pressure/temperature operating requirements.; First Article Test/Inspection on ;10; unit(s) in accordance with requirements ;IAW DWG 5894148 Rev "J" paragraph 3.2.1.1. The Type II Interface Cable Assemblies shall withstand exposure to a pressure/temperature combination of the proof pressure of NAVSEA Drawing 5759651; . 4.6 Production Lot Test (Contractor) - The Contractor shall perform Production Lot Testing in accordance with ;Production Lot Testing is required IAW DWG 5894148 Rev J. paragraph 3.4.1 and 4.2.1.1; . 4.7 Quality Conformance Inspection - The contractor is responsible for conducting a Quality Conformance Inspection in accordance with ;IAW DWG 5894148 rev. "J" 4.2 ; , paragraph ;All production units submitted for acceptance will be subjected to the inspections and performance tests of Figure 1 to assure conformance to the requirements. Dimensions, soldering, workmanship, and identification markings shall be verified in accordance with acceptance criteria as defined in drawings, specifications, and other requirement documents. Quality conformance tests and procedures specified for production unit acceptance are described in the following paragraphs 4.2.1 THRU 4.2.5.6. ; and preparing an inspection report in accordance with the Contract Data Requirements List, DD Form 1423. 4.8 Quality System Requirements - The supplier shall provide and maintain a quality system acceptable to the Government. The quality system requirements shall be in accordance with ISO 9001. 5. PACKAGING 5.1 Preservation, Packaging, Packing and Marking - Preservation, Packaging, Packing and Marking shall be in accordance with the Contract/Purchase Order Schedule and as specified below. MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE 6. NOTES 6.1 Ordering Information for Document References - The Department of Defense Single Stock Point (DODSSP), Website http://www.dsp.dla.mil/, provides product information for the Department Of Defense Index Of Specifications and Standards (DODISS) (i.e.Military/Federal Specifications and Standards), Data Item Descriptions (DIDs), and other DODSSP Products. A. Availability of Cancelled Documents - The DODSSP offers cancelled documents that are required by private industry in fulfillment of contractual obligations in paper format. Documents can be requested by phoning the Subscription Services Desk. B. Commercial Specifications, Standards, and Descriptions - These specifications, standards and descriptions are not available from Government sources. They may be obtained from the publishers of the applicable societies. C. Ordnance Standards (OS), Weapons Specifications (WS), and NAVORD OSTD 600 Pages - These type publications may be obtained by submitting a request to: Commander, Indian Head Division, Naval Surface Warfare Center Code 8410P, 101 Strauss Avenue Indian Head, MD 20640-5035 D. On post-award actions, requests for "Official Use Only" and "NOFORN" (Not Releasable To Foreign Nationals) documents must identify the Government Contract Number, and must be submitted via the cognizant Defense Contract Management Command (DCMC) for certification of need for the document. On pre-award actions such requests must be submitted to the PCO for certification of need for the document. E. NOFORN Military Specifications and Standards (including Amendments, Change Notices and Supplements, but NOT interim Changes) to be ordered from: Contracting Officer NAVICP-MECH Code 87321 5450 Carlisle Pike P.O. Box 2020 Mechanicsburg, Pa. 17055-0788 F. Nuclear Reactor Publications Assigned NAVSEA Documents and Identification Numbers (i.e. NAVSEA Welding Standard, NAVSEA 250-1500-1) are to be ordered from: Commanding Officer NAVICP-MECH Code 009 5450 Carlisle Pike P.O. Box 2020 Mechanicsburg, Pa. 17055-0788 G. Technical Manuals Assigned NAVSEA Identification Numbers (i.e. NAVSEA Welding And Brazing Procedure, NAVSEA S9074-AQ-GIB-010/248) are to be ordered from: Naval Inventory Control Point Code 1 Support Branch 700 Robbins Avenue Phildelphia, Pa. 19111-5094 H. Interim Changes and Classified Specifications shall be obtained by submitting a request on DD Form 1425 to NAVICP-MECH. 6.2 ;CONTRACTING CAN FIND QUALITY ASSURANCE PROVISIONS (QAPs) FOR 53711-5893731 ON DRIVE S: MECH NAVICP ICPM WSS General Shares N97 General Shares N9713 Technical Torpedo (QAPs) QUALITY ASSURANCE PROVISIONS QAP Final; DATE OF FIRST SUBMISSION=030 DAC ;Perform preproduction sampling IAW DWG 5894148 rev J section 3.4 ; DATE OF FIRST SUBMISSION=030 DAC ;Certificates of Quality Compliance for the following CableAssembly requirements shall be delivered to the government viaContract Data Requirements List (CDRL). Electrical Bulk Cable Supplier QA Program Plan. Test data and certificate of test conformance toverify that the Bulk Cable components, materialsand construction have been tested and that allrelated requirements have been met (53711-5906555). Notarized Certificate of Compliance for each lot ofdelivered Molding Compound material (53711-6105323)certifying that the material meets the specified requirements. Preproduction sample inspection and test data. Production Quality Conformance inspection and test data. Periodic Quality Conformance inspection and test data. Copies of the Certificate of Quality Compliance CDRLsshall be delivered to the Engineering Support Activity,NUWC Newport: NWPT.NUWC_8554_QAPCDRL@navy.mil james.c.ferguson1.civ@us.navy.mil richard.d.penfold2.civ@us.navy.mil patrick.r.faerber.civ@us.navy.mil Recommend a Post Award Conference be conducted withthe contractor/supplier to review the item Key Features.The government Engineering Support Activity, NUWC Newport,would like to participate in the conference if one isscheduled.;
N0010422QND73 Department of the Navy Naval Supply Systems Command
5/1/22, 9:38 AM