socket, assembly

Added: Apr 28, 2015 6:54 pm  

Proposed solicitation, SPE7M215R0054 is for NSN 1710-01-599-1835. Item is a Socket, Assembly, to be

manufactured  I/A/W DWG-80020-415788(REV E)

DWG-80020-316400(REV Y)

DWG-80020-323178(REV M)

DWG-80020-324629

DWG-80020-407961(REV AJ)

DWG-16236-CN015991835REVA

QAP-16236-SQAP015991835QA

QAP-16236-SQAP015991835GFAT

QAP-80020-CDRL-15-12019COQC

QAP-80020-CDRL-15-12019FAT

QAP-80020-CDRL-15-12019PTI

BARE ITEM MARKINGS SHALL BE WITH NAWC CAGE (80020) AND NAWC PART NUMBER

(415788-2) AND CONTRACT #

IF THE ITEMS DO NOT MEET THESE BARE MARKING REQUIREMENTS THEY ARE NOT

ACCEPTABLE.

PCO MANDATORY INSPECTION. DURING PRODUCTION,

MANDATORY INSPECTION IS REQUIRED TO BE

ACCOMPLISHED AND DOCUMENTED BY THE CONTRACTOR AS

FOLLOWS:

CRITICAL AND MAJOR CHARACTERISTICS AS IDENTIFIED

IN CLASSIFICATION OF CHARACTERISTICS BLOCK ON

DRAWING(S), TECHNICAL SPECIFICATIONS, SECOND

TIER DOCUMENTS REFERENCED IN THE ACQUISITION

ITEM DESCRIPTION AND SPECIFIED IN THE

PROCUREMENT DOCUMENT, AND CHARACTERISTICS

DEFINED AS:

(A) MATERIAL CERTIFICATIONS

(B) DESTRUCTIVE AND / OR NONDESTRUCTIVE

TEST RESULTS (WHEN APPLICABLE)

(C) ATTRIBUTES FOR PLATING HARDNESS

IMPORTANT MINOR CHARACTERISTICS SHALL BE

DEFINED BY THE CONTRACTOR SUBJECT TO QAR

CONCURRENCE, UNLESS OTHERWISE DEFINED ON

APPLICABLE DRAWING(S), SPECIFICATIONS

AND CHARRACTERISTICS DEFINED AS:

(A) DIAMETRICAL AND LINEAR DIMENSIONS

HAVING A TOLERANCE OF +/- 0.005 INCH OR

LESS

(B) GEOMETRIC FEATURE CONTROLS HAVING A TOTAL

TOLERANCE OF 0.003 INCH OR LESS

(C) SURFACE FINISHES HAVING A 16 VALUE OR LESS

(D) CLASS THREE THREADS

(E) ANGULAR TOLERANCES WITH A TOTAL RANGE LESS

THAN 1 DEGREE

LEVEL OF INSPECTION: ANSI / ASQC Z1.4 FOR SINGLE

SAMPLING USING A GENERAL INSPECTION LEVEL O II

(A) CRITICAL AND MAJOR CHARACTERISTICS: 100%

INSPECTION APPLIES

(B) IMPORTANT MINOR CHARACTERISTICS: AQL OF 1.5.

CERTIFICATION / DATA REPORTS: THE CONTRACTOR IS

RESPONSIBLE FOR PREPARING A CERTIFICATE OF

QUALITY COMPLIANCE (COQC) IN ACCORDANCE WITH THE

DD FORM 1423 CONTRACT DATA REQUIREMENTS LIST

(CDRL). THE COQC CONTENT WILL INCLUDE AS A

MINIMUM THE DATA DESCRIBED IN DLAR CLAUSE

52.246-9000, IN ADDITION TO ALL PCO MANDATORY

INSPECTION RESULTS. THIS COQC REQUIREMENT

APPLIES TO EACH UNIT OF CONTRACT QUANTITY.

IF AQLS ARE LISTED IN THE SPECIFICATION(S)

OR DRAWING(S) THEY MAY BE USED TO ESTABLISH THE

AUTHORIZED SAMPLE SIZE,HOWEVER,THE ACCEPTANCE

NUMBER FOR THIS CONTRACT IS ZERO;I.E.,THIS

CONTRACT REQUIRES A SAMPLING PLAN THAT ACCEPTS

ON ZERO DEFECTS AND REJECTS ON ONE OR MORE

DEFECT(S).

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE

USED NOR INCORPORATED IN ANY ITEMS TO BE

DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION

SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT

DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.

SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR

APPROVAL UNLESS THEY ARE AUTHORIZED BY THE

SPECIFICATION REQUIREMENTS.

THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO

EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA

AND ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED

THROUGH JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE

DEPARTMENTS OF STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO

INTERNATIONAL AGREEMENTS.

TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345, "MILITARY

CRITICAL TECHNICAL DATA AGREEMENT," FORM IS AVAILABLE AT THE WORLD WIDE

WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP OR BY WRITING TO:

DLA LOGISTICS INFORMATION SERVICE

FEDERAL CENTER

74 WASHINGTON AVE., NORTH

BATTLE CREEK, MI 49037-3084

 

TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A

CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCE AGREEMENT,

DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY

THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE OFFER, UNLESS AN

EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 "EXEMPTIONS OF

GENERAL APPLICABILITY," AND/OR EAR PART 740 ARE APPLICABLE.

NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL

DATA ARE REQUIRED TO PROVIDE THE CONTRACTING OFFICER WITH AN

APPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO

RECEIVE A COPY OF THE EXPORT CONTROLLED TECHNICAL DATA.

NOTE:  JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO

THEIR DD FORM 2345 CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH DATA

UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY

PERMITTED BY DODD 5230.25."

52.246-11 Higher Level Contract Quality Requirement (Manufacturers)

FAR CLAUSE 52.246-11 APPLIES.  A QUALITY MANAGEMENT PROGRAM MEETING THE

REQUIREMENTS OF ISO 9001:2008; A PROGRAM COMPARABLE TO ISO 9001:2008

(EXAMPLE SAE AS 9100), THE FOLLOWING TAILORED VERSION OF ISO 9001:2008;

OR A PROGRAM COMPARABLE TO THE TAILORED VERSION OF ISO 9001:2008

(EXAMPLE SAE AS 9003) IS REQUIRED. MIL-I-45208 AND MIL-Q-9858 ARE

OBSOLETE AND NO LONGER CONSIDERED SUITABLE WHEN HIGHER LEVEL QUALITY IS

REQUIRED. IN THE TAILORED VERSION OF THE ISO 9001:2008, ANY REFERENCES

WHICH CITE THE ENTIRE INTERNATIONAL STANDARD ARE INTERPRETED AS

EXCLUSIONS TO THIS DOCUMENT.

DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:2008

4.1 General requirements, [excluding reference to 1.2 and excluding NOTE

3 c)]

4.2.1 General, [excluding subparagraph a)]

4.2.2 Quality manual, [excluding subparagraph a)]

4.2.3 Control of documents

4.2.4 Control of records

5.1 Management commitment

5.3 Quality policy

6.2.2 Competence, training and awareness

6.4 Work environment

7.1 Planning of product realization, [excluding NOTE 2]

7.2.1 Determination of requirements related to the product

7.2.2 Review of requirements related to the product

7.2.3 Customer communication

7.3.7 Control of design and development changes

7.4.1 Purchasing process

7.4.3 Verification of purchased product

7.5.1 Control of production and service provision

7.5.3 Identification and traceability

7.5.4 Customer property

7.5.5 Preservation of product

7.6 Control of monitoring and measuring equipment

8.1 General, [excluding subparagraph b) and subparagraph c)]

8.2.2 Internal audit

8.2.4 Monitoring and measurement of product

8.3 Control of nonconforming product

8.5.2 Corrective action

8.5.3 Preventive action

CLAUSE 52.246-15, CERTIFICATE OF CONFORMANCE, IS

NOT AUTHORIZED FOR THIS NSN.

SOURCE INSPECTION REQUIRED.

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL

NOT BE INTENTIONALLY ADDED TO,OR COME IN DIRECT

CONTACT WITH,ANY HARDWARE OR SUPPLIES FURNISHED

UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY

USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED

INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;

AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.

PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS

CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN

A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR

MERCURY COMPOUND. (IAW NAVSEA 5100-003D).

REMINDER: THIS IS A CRITICAL ITEM AND ALL

MAJOR AND MINOR WAIVER/DEVIATION REQUESTS MUST

BE FORWARDED TO THE DSCC CONTRACTING OFFICER WHO

WILL COORDINATE THE REVIEW AND APPROVAL THROUGH

THE RESPONSIBLE ENGINEERING SERVICE ACTIVITY.

NOTE: THIS IS A RESTRICTED SOURCE ITEM AND

REQUIRES ENGINEERING SOURCE APPROVAL BY THE

GOVERNMENT DESIGN CONTROL ACTIVITY.

"CERTIFICATE OF QUALITY COMPLIANCE IS MANDATORY"

AIRCRAFT LAUNCH AND RECOVERY EQUIPMENT (ALRE).

CRITICAL APPLICATION ITEM..

ALL REQUESTS FOR WAIVERS OR DEVIATIONS

CLASSIFIED AS CRITICAL, MAJOR, OR MINOR MUST BE

FORWARDED TO THE DSC CONTRACTING OFFICER FOR

REVIEW AND APPROVAL..

ALL ITEMS OF SUPPLY SHALL BE MARKED IAW

MIL-STD-129.  IN ADDITION, EACH UNIT PACK WILL

BE MARKED WITH LOT AND SERIAL NUMBER (IF AVAILABLE),

CONTRACTOR'S CAGE CODE, ACTUAL MANUFACTURER'S

CAGE CODE AND PART NUMBER.

SURPLUS IS NOT ACCEPTABLE FOR THIS NSN.

CRITICAL APPLICATION ITEM

J. M. T. MACHINE COMPANY DBA 2A832 P/N 415788-2

L.R.G. CORPORATION DBA 75783 P/N 415788-2

PIONEER MACHINE & TOOLING CO DBA 47347 P/N 415788-2

IAW REFERENCE DRAWING NR 80020 316400

REVISION NR Y   DTD 07/07/2006

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 80020 415788

REVISION NR E   DTD 03/07/2011

PART PIECE NUMBER: 415788-2

IAW REFERENCE DRAWING NR 80020 324629

REVISION NR     DTD 04/27/2010

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 80020 407961

REVISION NR AJ  DTD 02/22/2012

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 80020 323178

REVISION NR M   DTD 02/06/2013

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 80020 323148

REVISION NR M   DTD 05/12/2013

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 16236 CN015991835

REVISION NR A   DTD 03/23/2015

PART PIECE NUMBER:

IAW REFERENCE QAP 16236 SQAP015991835GFAT

REVISION NR     DTD 03/23/2015

PART PIECE NUMBER:

IAW REFERENCE QAP 16236 SQAP015991835QA

REVISION NR     DTD 03/23/2015

PART PIECE NUMBER:

IAW REFERENCE QAP 80020 CDRL-15-12019FAT

REVISION NR     DTD 03/02/2015

PART PIECE NUMBER:

IAW REFERENCE QAP 80020 CDRL-15-12019PTI

REVISION NR     DTD 03/02/2015

PART PIECE NUMBER:

IAW REFERENCE QAP 80020 CDRL-15-12019COQC

REVISION NR     DTD 03/02/2015

PART PIECE NUMBER:

PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999

QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00

WRAP MAT:00 CUSH/DUNN MAT:NA CUSH/DUNN THKNESS:F

UNIT CONT:D3 OPI:M

INTRMDTE CONT:DO INTRMDTE CONT QTY:AAA

PACK CODE:U

MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.

SPECIAL MARKING CODE:00 -

PALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY 01, 2008

EACH UNIT PACKAGE WILL BE MARKED WITH THE NSN,

CONTRACT NUMBER, LOT NUMBER, CONTRACTOR CAGE

CODE, MANUFACTURER CAGE CODE, AND PART NUMBER.

PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999

QUP:001  PRES MTHD:41  CLNG/DRY:1  PRESV MAT:00

WRAP MAT:00  CUSH/DUNN MAT:NA  CUSH/DUNN THKNESS:F

UNIT CONT:D3  OPI:M

INTRMDTE CONT:DO  INTRMDTE CONT QTY:AAA

PACK CODE:U

MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.

SPECIAL MARKING CODE:00 -00 No special marking

PALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY 01, 2008

EACH UNIT PACKAGE WILL BE MARKED WITH THE NSN,

CONTRACT NUMBER, LOT NUMBER, CONTRACTOR CAGE

CODE, MANUFACTURER CAGE CODE, AND PART NUMBER.

The proposed solicitation will require FOB Destination and Inspection at Destination.  Proposed solicitation is for a total quantity of 210 each to be shipped to New Cumberland PA 17070.  Required delivery is 210 days for sources waived for FAT.  Additional days for non-waived sources will be granted and will be spelled out in the solicitation.  This item requires engineering source approval by the design control activity in order to maintain the quality of the part.  All responsible sources may submit an offer which shall be considered.  Proposed solicitation is set aside for small businesses.  Based on market research, the Government is not using the policies contained in Part 12, Acquisition of Commercial Items, in its solicitation for the described supplies or services.  However, interested persons may identify to the contracting officer their interest and capability to satisfy the Government's requirement with a commercial item within 15 days of this notice.  One or more of the items under this acquisition may be subject to Agreement on Government Procurement approved and implemented in the United States by the Trade Agreements Act of 1979. All offers shall be in the English language and in U.S. Dollars. All interested suppliers may submit an offer. This solicitation will be made available on its issue date.at HTTPS://WWW.DIBBS.BSM.DLA.MIL/ PLEASE NOTE: THE SOLICITATION WILL NOT BE AVAILABLE UNTIL THE ISSUE DATE. While price may be a significant factor in the evaluation of offers, the final award decision will be based upon a combination of price, delivery, past performance and other evaluation factors as described in the solicitation. A written offer is required and is to be returned to the bid room at Defense Supply Center Columbus, PO Box 3990, Columbus, OH 43218- 3990, or can be faxed to 614-692-4275. "Submission of proposal by

electronic commerce (e-mail) is allowed. Submit e-mailed proposals to the Bid and Abstract Room at:

ContractorProposalDLALandandMaritime@dla.mil Emailed proposals cannot exceed 15 MB." NO OFFERS

SHOULD BE EMAILED OR FAXED TO THE BUYER. Notice: This solicitation will contain DLAD provision 52.215-

9023 for Reverse Auction (RA). The Government reserves the right to activate this provision after timely offers

have been received and evaluated.