Pully, Flat

Added: Jan 07, 2016 5:50 pm

Proposed solicitation, SPE7M215R0079, is for NSN 3020-01-461-2737. Item is a Pully, Flat, to be manufactured I/A/W:
ALRE CSI

DWG-80020-627240(REV C)

DWG-80020-524681(REV A)

DWG-80020-626846(REV C)

DWG-80020-627239(REV C)

DWG-80020-TS15575(REV H)

DWG-16236-CN014612737

QAP-16236-SQAP014612737QA

QAP-16236-SQAP014612737CFAT

QAP-80020-CDRL15-12041COQC

QAP-80020-CDRL15-12041FAT

QAP-80020-CDRL15-12041PTI

THD-80020-TDR15-12041(GOVT ONLY)

Surplus is not acceptable for this NSN.

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE

USED NOR INCORPORATED IN ANY ITEMS TO BE

DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION

SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT

DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.

SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR

APPROVAL UNLESS THEY ARE AUTHORIZED BY THE

SPECIFICATION REQUIREMENTS.

REMINDER: THIS IS A CRITICAL ITEM AND ALL

MAJOR AND MINOR WAIVER/DEVIATION REQUESTS MUST

BE FORWARDED TO THE DSCC CONTRACTING OFFICER WHO

WILL COORDINATE THE REVIEW AND APPROVAL THROUGH

THE RESPONSIBLE ENGINEERING SERVICE ACTIVITY.

52.246-11 Higher Level Contract Quality Requirement (Manufacturers)

FAR CLAUSE 52.246-11 APPLIES. A QUALITY MANAGEMENT PROGRAM MEETING THE

REQUIREMENTS OF ISO 9001:2008; A PROGRAM COMPARABLE TO ISO 9001:2008

(EXAMPLE SAE AS 9100), THE FOLLOWING TAILORED VERSION OF ISO 9001:2008;

OR A PROGRAM COMPARABLE TO THE TAILORED VERSION OF ISO 9001:2008

(EXAMPLE SAE AS 9003) IS REQUIRED. MIL-I-45208 AND MIL-Q-9858 ARE

OBSOLETE AND NO LONGER CONSIDERED SUITABLE WHEN HIGHER LEVEL QUALITY IS

REQUIRED. IN THE TAILORED VERSION OF THE ISO 9001:2008, ANY REFERENCES

WHICH CITE THE ENTIRE INTERNATIONAL STANDARD ARE INTERPRETED AS

EXCLUSIONS TO THIS DOCUMENT.

DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:2008

4.1 General requirements, [excluding reference to 1.2 and excluding NOTE

3 c)]

4.2.1 General, [excluding subparagraph a)]

4.2.2 Quality manual, [excluding subparagraph a)]

4.2.3 Control of documents

4.2.4 Control of records

5.1 Management commitment

5.3 Quality policy

6.2.2 Competence, training and awareness

6.4 Work environment

7.1 Planning of product realization, [excluding NOTE 2]

7.2.1 Determination of requirements related to the product

7.2.2 Review of requirements related to the product

7.2.3 Customer communication

7.3.7 Control of design and development changes

7.4.1 Purchasing process

7.4.3 Verification of purchased product

7.5.1 Control of production and service provision

7.5.3 Identification and traceability

7.5.4 Customer property

7.5.5 Preservation of product

7.6 Control of monitoring and measuring equipment

8.1 General, [excluding subparagraph b) and subparagraph c)]

8.2.2 Internal audit

8.2.4 Monitoring and measurement of product

8.3 Control of nonconforming product

8.5.2 Corrective action

8.5.3 Preventive action

THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO

EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA

AND ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED

THROUGH JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE

DEPARTMENTS OF STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO

INTERNATIONAL AGREEMENTS.

TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345, MILITARY

CRITICAL TECHNICAL DATA AGREEMENT<(>,<)> FORM IS AVAILABLE AT THE WORLD

WIDE WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP OR BY WRITING TO:

DLA LOGISTICS INFORMATION SERVICE

FEDERAL CENTER

74 WASHINGTON AVE., NORTH

BATTLE CREEK, MI 49037-3084

TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A

CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCE AGREEMENT,

DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY

THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE OFFER, UNLESS AN

EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 EXEMPTIONS OF

GENERAL APPLICABILITY<(>,<)> AND/OR EAR PART 740 ARE APPLICABLE.

NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL

DATA ARE REQUIRED TO PROVIDE THE CONTRACTING OFFICER WITH AN

APPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO

RECEIVE A COPY OF THE EXPORT CONTROLLED TECHNICAL DATA.

NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO

THEIR DD FORM 2345 CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH DATA

UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY

PERMITTED BY DODD 5230.25.

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL

NOT BE INTENTIONALLY ADDED TO,OR COME IN DIRECT

CONTACT WITH,ANY HARDWARE OR SUPPLIES FURNISHED

UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY

USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED

INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;

AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.

PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS

CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN

A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR

MERCURY COMPOUND. (IAW NAVSEA 5100-003D).

AIRCRAFT LAUNCH AND RECOVERY EQUIPMENT (ALRE)

.

CRITICAL APPLICATION ITEM.

.

ALL REQUESTS FOR WAIVERS OR DEVIATIONS

CLASSIFIED AS CRITICAL, MAJOR, OR MINOR MUST BE

FORWARDED TO THE DSC CONTRACTING OFFICER FOR

REVIEW AND APPROVAL.

.

ALL ITEMS OF SUPPLY SHALL BE MARKED IAW

MIL-STD-129. IN ADDITION, EACH UNIT PACK WILL

BE MARKED WITH LOT AND SERIAL NUMBER (IF AVAILABLE),

CONTRACTOR'S CAGE CODE, ACTUAL MANUFACTURER'S

CAGE CODE AND PART NUMBER.

THIS MATERIAL MUST MEET NAVAIR AIRCRAFT LAUNCH &

RECOVERY EQUIPMENT TRACEABILITY REQUIREMENTS. BARE

ITEM MARKINGS SHALL BE IAW THE TECHNICAL DATA

DRAWINGS PROVIDED.

BARE ITEM MATERIAL SHALL BE MARKED WITH CONTRACT

NUMBER, NAWC CAGE, AND PART NUMBER UNLESS OTHERWISE

SPECIFICIED ON ASSOCIATED DRAWING. IF A CONFLICT

EXISTS WITH MARKING REQUIREMENTS OF THIS 82N ALRE/SE

ITEM, THE ASSOCIATED DRAWING REQUIREMENTS SHALL APPLY.

CRITICAL APPLICATION ITEM

ADVANCE DEVELOPMENT & 05201 P/N 627240-1

IAW REFERENCE DRAWING NR 80020 524681

REVISION NR DTD 05/03/1997

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 80020 TS15575

REVISION NR H DTD 03/02/2006

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 80020 627239

REVISION NR C DTD 08/13/2008

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 80020 627240

REVISION NR C DTD 10/30/2002

PART PIECE NUMBER: 627240-1

IAW REFERENCE DRAWING NR 80020 626846

REVISION NR C DTD 07/23/2014

PART PIECE NUMBER:

IAW REFERENCE NON GOVT STD NAS1352

REVISION NR 12 DTD 05/13/2014

PART PIECE NUMBER:

IAW REFERENCE NON GOVT STD NASM16555

REVISION NR 2 DTD 04/21/2014

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 16236 CN014612737

REVISION NR DTD 06/02/2015

PART PIECE NUMBER:

IAW REFERENCE QAP 16236 SQAP014612737QA

REVISION NR DTD 06/02/2015

PART PIECE NUMBER:

IAW REFERENCE QAP 16236 SQAP014612737CFAT

REVISION NR DTD 06/02/2015

PART PIECE NUMBER:

IAW REFERENCE QAP 80020 CDRL15-12041COQC

REVISION NR DTD 04/08/2015

PART PIECE NUMBER:

IAW REFERENCE QAP 80020 CDRL15-12041FAT

REVISION NR DTD 04/08/2015

PART PIECE NUMBER:

IAW REFERENCE QAP 80020 CDRL15-12041PTI

REVISION NR DTD 04/08/2015

PART PIECE NUMBER:

 

Packaging shall be I/A/W: 

PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999

QUP:001 PRES MTHD:33 CLNG/DRY:1 PRESV MAT:09

WRAP MAT:GB CUSH/DUNN MAT:AD CUSH/DUNN THKNESS:F

UNIT CONT:FO OPI:O

PACK CODE:U

MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.

SPECIAL MARKING CODE:ZZ -ZZ Special Requirements

PALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY 01, 2008

EACH UNIT PACKAGE WILL BE MARKED WITH THE NSN,

CONTRACT NUMBER, LOT NUMBER, CONTRACTOR CAGE

CODE, MANUFACTURER CAGE CODE, AND PART NUMBER.

 

The proposed solicitation will require FOB origin, inspection at source, acceptance at destination.  Proposed solicitation is for a total quantity of 260 each, to be shipped to New Cumberland PA 17070-5002.  Required delivery is 390 days for sources waived for FAT. Additional days for non-waived sources will be granted and will be spelled out in the solicitation. This item requires engineering source approval by the design control activity in order to maintain the quality of the part.  Only Advance Development and Manufacturing (cage 05201) is currently listed as an approved source.  All responsible sources may submit an offer which shall be considered. Proposed solicitation is unrestricted. Based on market research, the Government is not using the policies contained in Part 12, Acquisition of Commercial Items, in its solicitation for the described supplies or services. However, interested persons may identify to the contracting officer their interest and capability to satisfy the Government's requirement with a commercial item within 15 days of this notice. One or more of the items under this acquisition may be subject to Agreement on Government Procurement approved and implemented in the United States by the Trade Agreements Act of 1979. All offers shall be in the English language and in U.S. Dollars. All interested suppliers may submit an offer. This solicitation will be made available on its issue date of approximately 1/29/16 at HTTPS://WWW.DIBBS.BSM.DLA.MIL/ PLEASE NOTE: THE SOLICITATION WILL NOT BE AVAILABLE UNTIL THE ISSUE DATE. While price may be a significant factor in the evaluation of offers, the final award decision will be based upon a combination of price, delivery, past performance and other evaluation factors as described in the solicitation. A written offer is required and is to be returned to the bid room at Defense Supply Center Columbus, PO Box 3990, Columbus, OH 43218- 3990, or can be faxed to 614-692-4275. "Submission of proposal by electronic commerce (e-mail) is allowed. Submit e-mailed proposals to the Bid and Abstract Room at: ContractorProposalDLALandandMaritime@dla.mil Emailed proposals cannot exceed 15 MB." NO OFFERS SHOULD BE EMAILED OR FAXED TO THE BUYER. Notice: This solicitation contains DLAD provision 52.215-9023 for Reverse Auction (RA). The Government reserves the right to activate this provision after timely offers have been received and evaluated.