CO LFX Target Build

This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information included in this notice. The solicitation number is HAAF175AML0104 and is issued as an invitation for bids (IFB), unless otherwise indicated herein. The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2005-101. The associated North American Industrial Classification System (NAICS) code for this procurement is 321992 with a small business size standard of 500.00 employees. This requirement is a [ Small Business ] set-aside and only qualified offerors may submit bids. The solicitation pricing on www.FedBid.com will start on the date this solicitation is posted and will end on 2019-03-14 11:00:00.0 Eastern Time or as otherwise displayed at www.FedBid.com. FOB Destination shall be Fort Campbell, KY 42223
The MICC End User requires the following items, Brand Name or Equal, to the following:
LI 001: Type A Targets See attachment for schematics and supply list for details.
1.Emplace 2 Type A target buildings on Range 42 as specified by a schematic provided to the contractor NLT 05 April 2019.
2.Type A target buildings will be 16’x16’ and will at minmum be constructed from 2x4 with 24 inch spacing on center between Studs, with ¾ inch Plywood sheeting, see provided schematic for windows and doors.
3. Each building will have an exterior breach door that is solid oak., 2, EA;
LI 002: Type B Targets See attachment for schematics and supply list for details.
1. Emplace 1 Type B target building on Range 42 as specified by a schematic provided to the contractor NLT 05 April 2019.
2. Type B target buildings will be 16’x32’ and will at minmum be constructed from 2x4 with 24 inch spacing on center between Studs, with ¾ inch Plywood sheeting, see provided schematic for windows and doors.
3. Each building will have an exterior breach door that is solid oak., 1, EA;
LI 003: Compound Enclosure
1. Install 250 Linear feet of plywood wall in accordance with schematic. Wall will be 8’ high with studs 24 inches on center and supporting beams to the ground every 24 inches. Wall will be anchored to ground with minimum 2 foot stakes every 10 feet.
2. The fence will have 1x 10’ gate that will accommodate vehicle traffic into the compound as specified by the schematic., 250, FT;
LI 004: Breaching Walls
1. Pre-fabricate and deliver 12 breaching walls 4 feet wide, and 8 feet tall.
2. Walls will be framed with ¼ in. steel, bottom of frame will have rectangular steel to to enable movement with forklift.
3. Walls will be filled with 3,000lb concrete from bottom to top frame. Walls should only be reinforced with enough remesh necessary to hold the concrete in place. Walls will only be 3-4 in thick and have smallest gauge remesh possible., 12, EA;
LI 005: 36"x80" 3/4in plywood doors. Doors will have 3 hinges pre-attached. Hinges will be 3-1/2in x 5/8 in nickel hinges., 80, EA;
LI 006: New Dewalt 6-1/2 in. (165 mm) Track Saw Kit
•Includes DWS520K 6-1/2 in. Track Saw, 48-tooth, ultra-fine finishing blade, blade wrench, case
•For use with track saw dual-edged tracks (sold separately) for perfectly straight cuts in both directions
•Straight plunge mechanism for optimal ergonomics
•Continuous anti-kickback mechanism and riving knife prevent kickback when engaged
•Low profile blade guard allows saw to be used in confined spaces
•Universal 1-1/4 in. dust port for 90% efficient dust collection with vacuum
•Cuts through hardwoods, all common woodworking and construction material
•Great for ripping, crosscutting, mitering, inlay work, cutting cabinet openings, door trimming on hinges, cutting multiple pieces at once
•Backed by a 90-day money-back guarantee, full 1-year service contract and 3-year limited warranty
•Click here for more information on Electronic Recycling Programs, 2, EA;
LI 007: New Dewalt 59 in. Track Saw Track
•Dual-edged tracks allow straight cuts in both directions
•Ideal for ripping, cross cutting and mitering sheet goods
•Compact design makes it easily portable
This 59 in. dual-edged TrackSaw from DEWALT makes it easy to perform straight, precise cuts in both directions, a particularly handy instrument when cutting large sheets of wood. Ideal for cabinetry and furniture building, woodworkers can use this device to accurately make plunge cuts, cutting cabinet openings, door trimming on the hinges and gang cutting.
•Zero clearance TrackSaw cutting system delivers precise, straight, splinter-free cuts
•Makes easy work of truing/edge joining
•Great for making cabinets and bookcases
•3-year limited warranty, 2, EA;
LI 008: New DEWALT 48-Teeth Precision Ground Woodworking Blade for TrackSaw System
•Flex resistant laser cut plate â€" for extreme accuracy
•Ultra sharp woodworking grade carbide â€" for superb finish
•Large carbide â€" allows for multiple re-sharpening
•Laser etched graphics â€" provide grind and application information
•20 mm arbor for use with TrackSaw saws
•Made in the USA, 6, EA;
LI 009: New DEWALT 25 ft. x 1-1/4 in. XP Premium Tape Measure
This tape is 25 ft. L with 13 ft. of stand out. With an integrated belt clip and lanyard slot, this tape is always at the ready.
•Reinforced tough case for improved drop durability
•13 ft. of straighter standout for even better user efficiency
•Our new, strongest blade coating for even longer blade life
•9 in. of end hook reinforcement maximizes blade life and reduces blade breakage at the hook
•Integrated lanyard slot and belt clip
•25 ft. tape, 10, EA;
LI 010: New DEWALT 20 oz Hammer
1-piece hammer is designed to be reliable and extremely durable. The weight of this hammer is evenly distributed, providing a strong and comfortable swing.
•Optimal weight distribution for a more controlled swing
•Side nail puller for efficient nail pulling
•Oval shaped strike face makes toe-nailing easier
•A better balanced hammer can help relieve user fatigue and pain, 10, EA;
LI 011: Cubic Yards of Dirt. Cheapest possible soil will be provided., 200, Cubic Yards;
LI 012: 1 in thick RTD plywood sheets 4'x8'. Must be delivered on 25 MAR 2019., 350, EA;
LI 013: 2"x4"x 16' grade 2 lumber. Must be delivered on 25 MAR 2019., 700, EA;
LI 014: 1"x1" x 16' grade 2 lumber. Must be delivered on 25 MAR 2019., 50, EA;
LI 015: 4" x 4"x 16' grade 2 lumber. Must be delivered on 25 MAR 2019., 100, EA;
LI 016: 5" 40D nails. Must be delivered on 25 MAR 2019., 200, EA;
LI 017: 3 in. x 0.131 Plastic 4M Vinyl-Coated Steel Smooth Shank Framing Nail 21 Degree (1,000 per box), 2, BX;
LI 018: 2 in. x 0.113-Gauge Plastic 1M Galvanized Steel Ring Exterior Round Nails (1,000 per Box)
21 Degree, 2, BX;
LI 019: Shipping to Fort Campbell, KY., 1, EA;
LI 020: Removal of all buildings, destroyed doors, and concrete from the walls upon completion of the training. Training will conclude NLT 1200 on 12APR and the debris needs to be removed NLT 16APR19., 1, EA;
Solicitation and Buy Attachments
***Question Submission: Interested offerors must submit any questions concerning the solicitation at the earliest time possible to enable the Buyer to respond. Questions must be submitted by using the 'Submit a Question' feature at www.fedbid.com. Questions not received within a reasonable time prior to close of the solicitation may not be considered.***
For this solicitation, MICC End User intends to conduct an online competitive reverse auction to be facilitated by the third-party reverse auction provider, FedBid, Inc. FedBid has developed an online, anonymous, browser based application to conduct the reverse auction. An Offeror may submit a series of pricing bids, which descend in price during the specified period of time for the aforementioned reverse auction. MICC End User is taking this action in an effort to improve both vendor access and awareness of requests and the agency's ability to gather multiple, competed, real-time bids. All responsible Offerors that respond to this solicitation MUST submit the pricing portion of their bid using the online exchange located at www.FedBid.com. There is no cost to register, review procurement data or make a bid on www.FedBid.com. Offerors that are not currently registered to use www.FedBid.com should proceed to www.FedBid.com to complete their free registration. Offerors that require special considerations or assistance may contact the FedBid Helpdesk at 877-9FEDBID (877-933-3243) or via email at marketplacesupport@unisonglobal.com. Offerors may not artificially manipulate the price of a transaction on www.FedBid.com by any means. It is unacceptable to place bad faith bids, to use decoys in the www.FedBid.com process or to collude with the intent or effect of hampering the competitive www.FedBid.com process. Should offerors require additional clarification, notify the point of contact or FedBid at 877-9FEDBID (877-933-3243) or marketplacesupport@unisonglobal.com.Use of FedBid: Buyers and Sellers agree to conduct this transaction through FedBid in compliance with the FedBid Terms of Use. Failure to comply with the below terms and conditions may result in offer being determined as non-responsive.
The offeror must comply with the following commercial item terms and conditions: FAR 52.252-1, Solicitation. Provisions Incorporated by Reference; FAR 52.212-1, Instructions to Offerors; 52.212-3, Offeror Representations and Certifications; FAR 52.211-6, Brand name or Equal.
The following clauses apply to this solicitation: FAR 52.212-4, Contract Terms and Conditions â€" Commercial Items. The following FAR clauses in paragraph (b) of FAR clause 52.212-5, Contract Terms and Conditions Required To Implement Statutes or Executive Orders-Commercial Items, apply: 52.204-10, Reporting Executive Compensation and First Tier Subcontract Awards; 52.219-6, Notice of Total Small Business Set-Aside; 52.219-28, Post Award Small Business Program Rerepresentation; 52.222-3, Convict Labor; 52.222-19, Child Labor-Cooperation with Authorities and Remedies; 52.222-21, Prohibition of Segregated Facilities; 52.222-26, Equal Opportunity; 52.222-36, Affirmative Action for Workers with Disabilities; 52.225-13, Restrictions on Certain Foreign Purchases; 52.232-33, Payment by Electronic Funds Transfer--System for Award Management. 52.233-4, Applicable Law for Breach of Contract Claim; The following DFARS clauses apply: DFARS 252.04-7004, Alternate A System for Award Management; 252.211-7003, Item Identification and Valuation; 252.225-7002, Qualifying Country Sources as Subcontractors; 252.232-7010, Levies on Contract Payments; 252.203-7000, Requirements Relating to Compensation of Former DoD Officials; 252.225-7001, Buy American Act and Balance Of Payments Program; 252.225-7036, Buy American Act -- Free Trade Agreements -- Balance of Payments Program; 252.232-7003, Electronic Submission of Payment Requests; 252.247-7023, Primary and ALT III, Transportation of Supplies by Sea.
IAW 52.204-7 System for Award Management (SAM) Registration (July 2013), the offeror must be registered in SAM and fully input their Representations and Certifications for a complete record. Information can be found at http://www.sam.gov or by calling 866-606-8220, or 334-206-7828 for international calls. 52.204-13 - System for Award Management Maintenance
Shipping is FOB Destination CONUS (CONtinental U.S.).
New Equipment ONLY. NO USED OR REMANUFACTURED PRODUCTS WILL BE ACCEPTED.
Submitted Quotes will be valid for 45 days after the auction closing.
This solicitation is issued as a Request for Quotation (RFQ), not an invitation for bid (IFB).).
IAW FAR 52.252-2 Clauses Incorporated by Reference, the full text of FAR and DFARS Clauses may be accessed electronically at http://farsite.hill.af.mil; and are current to the most recent revision dates posted on this site.
The associated North American Industrial Classification System (NAICS) code
for this procurement can be found. The small business size
standard for that NAICS code can be found at https://www.sba.gov/sites/default/files/files/Size_Standards_Table.pdf
"AMC-Level Protest Program If you have complaints about this procurement, it is preferable that you first attempt to resolve those concerns with the responsible contracting officer. However, you can also protest to Headquarters (HQ), Army Materiel Command (AMC). The HQ AMC-Level Protest Program is intended to encourage interested parties to seek resolution of their concerns within AMC as an Alternative Dispute Resolution forum, rather than filing a protest with the Government Accountability Office (GAO) or other external forum. Contract award or performance is suspended during the protest to the same extent, and within the same time periods, as if filed at the GAO. The AMC protest decision goal is to resolve protests within 20 working days from filing. To be timely, protests must be filed within the periods specified in FAR 33.103. If you want to file a protest under the HQ AMC-Level Protest Program, the protest must request resolution under that program and be sent to the address below. All other agency-level protests should be sent to the contracting officer for resolution. Headquarters U.S. Army Materiel Command
Office of Command Counsel
4400 Martin Road
Rm: A6SE040.001
Redstone Arsenal, AL 35898-5000
Fax: (256) 450-8840
Packages sent by FedEx or UPS should be addressed to:
Headquarters U.S. Army Materiel Command
Office of Command Counsel
4400 Martin Road
Rm: A6SE040.001
Redstone Arsenal, AL 35898-5000
Fax: (256) 450-8840 The AMC-Level Protest procedures are found at: http://www.amc.army.mil/pa/COMMANDCOUNSEL.asp.
If internet access is not available, contact the contracting officer or HQ, AMC to obtain the HQ AMC-Level Protest Procedures."
"52.204-9, Personal Identity Verification of Contractor Personnel; 52.204-10,
Reporting Executive Compensation and First-Tier Subcontract Awards; 52.222-41, Service Contract Act; 52.237-2, Protection of Government
Buildings, Equipment and Vegetation; 252.201-7000, COR Clause; 252.223-7006,
Prohibition On Storage And Disposal Of Toxic And Hazardous Materials;
252.243-7001, Pricing of Contract Modifications; 252.246-7000, Material
inspection and receiving report"
Representation by Corporations Regarding an Unpaid Tax Liability or a Felony Conviction under any Federal Law.
Wide Area WorkFlow Payment Instructions
252.204-7012 Safeguarding of Unclassified Controlled Technical Information
All deliveries shall be palletized when the material exceeds 250 lbs. (excluding the pallet), or exceeds 20 cubic feet, to comply with the requirements of Department of the Army Pamphlet 700-32 and MIL-STD-147E.
This is currently an unfunded requirement with a high expectation that funds will be available. When and if funds become available a contract will be awarded at that time.
IAW FAR 52.212-2; Evaluation - Commercial Items, the following factor shall be used to evaluate offers: technical capability of the item offered to meet the Government requirement and price. Technical capability is more important than price.
No multiple awards will be made. Quotes received through Unison Marketplace will be evaluated and awarded on an Â"all-or-nothingÂ" basis.
Wide Area WorkFlow Payment Instructions
Please address your questions through the Unison Marketplace buy. If your questions are not being answered in a timely manner, please send your question to the S2P2 Contracting Officer - usarmy.drum.acc-micc.mbx.micc@mail.mil or call 315-772-5582.
.