A02_W91CRB-17-R-5012_solicitation.pdf

SOLICITATION, OFFER AND AWARD 1. This Contract Is A Rated Order Under

DPAS (15 CFR 700)

Rating Page of Pages

2. Contract Number 3. Solicitation Number 4. Type of Solicitation 5. Date Issued 6. Requisition/Purchase Number Sealed Bid (IFB)

Negotiated (RFP)

7. Issued By Code 8. Address Offer To (If Other Than Item 7)

NOTE: In sealed bid solicitations ‘offer’ and ‘offeror’ mean ‘bid’ and ‘bidder’.

SOLICITATION

9. Sealed offers in original and copies for furnishing the supplies or services in the Schedule will be received at the place specified in item 8, or if handcarried, in the depository located in until (hour) local time (Date).

Caution - Late Submissions, Modifications, and Withdrawals: See Section L, Provision No. 52.214-7 or 52.215-1. All offers are subject to all terms and conditions contained in this solicitation.

10. For Information A. Name B. Telephone (No Collect Calls) C. E-mail Address

Call: Area Code Number Ext.

11. Table Of Contents

(X) Sec. Description Page(s) (X) Sec. Description Page(s)

Part I - The Schedule Part II - Contract Clauses A Solicitation/Contract Form I Contract Clauses

B Supplies or Services and Prices/Costs Part III - List Of Documents, Exhibits, And Other Attach.

C Description/Specs./Work Statement J List of Attachments D Packaging and Marking Part IV - Representations And Instructions E Inspection and Acceptance K Representations, Certifications, and F Deliveries or Performance Other Statements of Offerors G Contract Administration Data L Instrs., Conds., and Notices to Offerors H Special Contract Requirements M Evaluation Factors for Award

OFFER (Must be fully completed by offeror) NOTE: Item 12 does not apply if the solicitation includes the provisions at 52.214-16, Minimum Bid Acceptance Period.

12. In compliance with the above, the undersigned agrees, if this offer is accepted within _____ calendar days (60 calendar days unless a different period is inserted by the offeror) from the date for receipt of offers specified above, to furnish any or all items upon which prices are offered at the price set opposite each item, delivered at the designated point(s), within the time specified in the schedule.

13. Discount For Prompt Payment 10 Calendar Days (%) 20 Calendar Days (%) 30 Calendar Days (%) Calendar Days (%) (See Section I, Clause No. 52.232-8)

14. Acknowledgment of Amendments (The offeror acknowledges Amendment No. Date Amendment No. Date receipt of amendments to the SOLICITATION for offerors and related documents numbered and dated):

15A. Name and Code Facility 16. Name and Title of Person Authorized to Sign Offer Address of (Type or Print) Offeror

15B. Telephone Number 15C. Check if Remittance Address is 17. Signature 18. Offer Date Area Code Number Ext. Different From Above – Enter such

Address In Schedule

AWARD (To be completed by Government)

19. Accepted As To Items Numbered 20. Amount 21. Accounting And Appropriation

22. Authority For Using Other Than Full And Open Competition: 23. Submit Invoices To Address Shown In Item

10 U.S.C. 2304(c)( ) 41 U.S.C. 253(c)( ) (4 copies unless otherwise specified)

24. Administered By (If other than Item 7) Code 25. Payment Will Be Made By Code

26. Name of Contracting Officer (Type or Print) 27. United States Of America 28. Award Date

(Signature of Contracting Officer)

IMPORTANT - Award will be made on this Form, or on Standard Form 26, or by other authorized official written notice.

AUTHORIZED FOR LOCAL REPRODUCTION Standard Form 33 (Rev. 9-97) Previous edition is unusable Prescribed By GSA-FAR (48 CFR) 53.214(c)

W91CRB-17-R-5012

X

NONE

SEE SCHEDULE

W91CRB

W6QK ACC-APG DIVISION D

4118 SUSQUEHANNA AVE

ABERDEEN PROVING GROU MD 21005-5001

SHAWN L. JAMERSON

(410)278-5412

CCAP-SCD

SHAWN.L.JAMERSON.CIV@MAIL.MIL

1 55

X 1

X 3 X 11

X 24

X 29

X 31

X 32

X 38

X 53

X 55

CONTINUATION SHEET

Reference No. of Document Being Continued Page of

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

SECTION A - SUPPLEMENTAL INFORMATION

Buyer Name: SHAWN L. JAMERSON

Buyer Office Symbol/Telephone Number: CCAP-SCD/(410)278-5412

Type of Contract 1: Firm Fixed Price

Kind of Contract: Supply Contracts and Priced Orders

FMS REQUIREMENT

*** End of Narrative A0000 ***

1. This is a firm fixed price solicitation to procure Vector Laser Range Finders per Section B as required under FMS case MD-B-UBN/UBQ, ARMS F20297:

2. Inspection and Acceptance of these items shall be at Origin by cognizant DCMA.

3. Vendor is not to ship items - shipping instructions are in the Deliverable and Performance section of this solicitation/contract.

4. No authorized split shipments. Early deliveries are authorized

5. Preservation and packaging for shipment shall be in accordance with Section D. Packaging/packing shall be in accordance with ASTM D

3951-10, Commercial Packaging and Preservation, Level of Protection (LOP), Level of Pack (LPK): Commercial, Quantity Unit Pack (QUP):

001. Marking shall be in accordance with MIL-STD-129R.

6. All other terms and conditions are contained herein.

*** END OF NARRATIVE A0001 ***

2 55

PIIN/SIIN

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

SECTION B - SUPPLIES OR SERVICES AND PRICES/COSTS

0001 VECTOR IV 3KM LASER RANGE FINDER 3 EA $ $ ________________________________ ______________ __________________

COMMODITY NAME: BINOCULAR LASER RANGEFINDER

CLIN CONTRACT TYPE:

Firm Fixed Price

PRON: J56SAC549C PRON AMD: 01

AMS CD: MDUBN006

FMS COUNTRY/CASE: MD/UBN

CLIN 0001 - See Section

3.1.0.1 of PWS for salient characteristics

(End of narrative B001)

Packaging and Marking _____________________

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Origin

Deliveries or Performance _________________________

DOC SUPPL

REL CD MILSTRIP ADDR SIG CD MARK FOR TP CD ______ ________ ______ ______ ________ _____

001 BMDA7N62109006 BXXUBN L 2

PROJ CD BRK BLK PT _______ __________

BMDA00

DEL REL CD QUANTITY DAYS AFTER AWARD __________ ______________ ________________

001 3 0090

FOB POINT: Origin

SHIP TO:

(BMDA00) SEE SSI

0002 VECTOR IV LASER RANGEFINDER 2 EA $ $ ___________________________ ______________ __________________

NSN: 6006-00-001-0017

COMMODITY NAME: VECTOR IV SR1 RANGEFINDER

CLIN CONTRACT TYPE:

Firm Fixed Price

PRON: J56SAZ191G PRON AMD: 01

AMS CD: 431100

FMS COUNTRY/CASE: MD/UBQ

3 55

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

CLIN 0002 - See Section

3.1.0.2 of PWS for salient characteristics

(End of narrative B001)

Packaging and Marking _____________________

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Origin

Deliveries or Performance _________________________

DOC SUPPL

REL CD MILSTRIP ADDR SIG CD MARK FOR TP CD ______ ________ ______ ______ ________ _____

001 BMDA7N62099001 BXXUBQ L 2

PROJ CD BRK BLK PT _______ __________

BMDA00

DEL REL CD QUANTITY DAYS AFTER AWARD __________ ______________ ________________

001 2 0090

FOB POINT: Origin

SHIP TO:

(BMDA00) SEE SSI

0003 NITE LASER RANGEFINDER W/ I2T TECH 2 EA $ $ __________________________________ ______________ __________________

COMMODITY NAME: COMMERCIAL VECTOR IV

CLIN CONTRACT TYPE:

Firm Fixed Price

PRON: J56SAZ201G PRON AMD: 01

AMS CD: 431100

FMS COUNTRY/CASE: MD/UBQ

CLIN 0003 - See Section

3.1.0.3 of PWS for salient characteristics

(End of narrative B001)

Packaging and Marking _____________________

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Origin

Deliveries or Performance _________________________

4 55

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

DOC SUPPL

REL CD MILSTRIP ADDR SIG CD MARK FOR TP CD ______ ________ ______ ______ ________ _____

001 BMDA7N62099002 BXXUBQ L 2

PROJ CD BRK BLK PT _______ __________

BMDA00

DEL REL CD QUANTITY DAYS AFTER AWARD __________ ______________ ________________

001 2 0090

FOB POINT: Origin

SHIP TO:

(BMDA00) SEE SSI

0004 VECTOR 21 NITE W/ I2T TECH 10 EA $ $ __________________________ ______________ __________________

NSN: 5855-00-001-0017

COMMODITY NAME: VECTOR-21 NITE RANGEFINDER

CLIN CONTRACT TYPE:

Firm Fixed Price

PRON: J56SAZ211G PRON AMD: 01

AMS CD: 431100

FMS COUNTRY/CASE: MD/UBQ

CLIN 0004 - See Section

3.1.0.4 of PWS for salient characteristics

(End of narrative B001)

Packaging and Marking _____________________

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Origin

Deliveries or Performance _________________________

DOC SUPPL

REL CD MILSTRIP ADDR SIG CD MARK FOR TP CD ______ ________ ______ ______ ________ _____

001 BMDA7N62099003 BXXUBQ L 2

PROJ CD BRK BLK PT _______ __________

BMDA00

DEL REL CD QUANTITY DAYS AFTER AWARD __________ ______________ ________________

001 10 0090

FOB POINT: Origin

SHIP TO:

(BMDA00) SEE SSI

5 55

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

0005 VECTOR 23 ULTIMATE LASER RANGEFINDER 2 EA $ $ ____________________________________ ______________ __________________

NSN: 5855-00-001-0018

COMMODITY NAME: COMMERCIAL VECTOR 23

CLIN CONTRACT TYPE:

Firm Fixed Price

PRON: J56SAZ221G PRON AMD: 01

AMS CD: 431100

FMS COUNTRY/CASE: MD/UBQ

CLIN 0005 - See Section

3.1.0.5 of PWS for salient characteristics

(End of narrative B001)

Packaging and Marking _____________________

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Origin

Deliveries or Performance _________________________

DOC SUPPL

REL CD MILSTRIP ADDR SIG CD MARK FOR TP CD ______ ________ ______ ______ ________ _____

001 BMDA7N62099004 BXXUBQ L 2

PROJ CD BRK BLK PT _______ __________

BMDA00

DEL REL CD QUANTITY DAYS AFTER AWARD __________ ______________ ________________

001 2 0090

FOB POINT: Origin

SHIP TO:

(BMDA00) SEE SSI

0006 VECTOR IV SPARES AND ACCESSORIES KIT 1 EA $ $ ____________________________________ ______________ __________________

COMMODITY NAME: Vector IV Spares (UI

CLIN CONTRACT TYPE:

Firm Fixed Price

PRON: J56SAZ231G PRON AMD: 01

AMS CD: 431100

FMS COUNTRY/CASE: MD/UBQ

CLIN 0006 - See Section

3.1.0.6.1 of PWS for salient characteristics

6 55

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

(End of narrative B001)

Packaging and Marking _____________________

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Origin

Deliveries or Performance _________________________

DOC SUPPL

REL CD MILSTRIP ADDR SIG CD MARK FOR TP CD ______ ________ ______ ______ ________ _____

001 BMDA7N6209D005 BXXUBQ L 2

PROJ CD BRK BLK PT _______ __________

BMDA00

DEL REL CD QUANTITY DAYS AFTER AWARD __________ ______________ ________________

001 1 0090

FOB POINT: Origin

SHIP TO:

(BMDA00) SEE SSI

0007 VECTOR IV NITE SPARES AND ACCESSORIES 1 EA $ $ _____________________________________ ______________ __________________

COMMODITY NAME: VECTOR IV NITE SPARES

CLIN CONTRACT TYPE:

Firm Fixed Price

PRON: J56SAZ251G PRON AMD: 01

AMS CD: 431100

FMS COUNTRY/CASE: MD/UBQ

CLIN 0007 - See Section

3.1.0.6.2 of PWS for salient characteristics

(End of narrative B001)

Packaging and Marking _____________________

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Origin

Deliveries or Performance _________________________

DOC SUPPL

REL CD MILSTRIP ADDR SIG CD MARK FOR TP CD ______ ________ ______ ______ ________ _____

001 BMDA7N6209D105 BXXUBQ L 2

7 55

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

PROJ CD BRK BLK PT _______ __________

BMDA00

DEL REL CD QUANTITY DAYS AFTER AWARD __________ ______________ ________________

001 1 0090

FOB POINT: Origin

SHIP TO:

(BMDA00) SEE SSI

0008 VECTOR 21 SPARES AND ACCESSORIES 1 PK $ $ ________________________________ ______________ __________________

COMMODITY NAME: SPARES FOR VECTOR 21

CLIN CONTRACT TYPE:

Firm Fixed Price

PRON: J57SAA519C PRON AMD: 01

AMS CD: 431100

FMS COUNTRY/CASE: MD/UBQ

CLIN 0008 - See Section

3.1.0.6.3 of PWS for salient characteristics

(End of narrative B001)

Packaging and Marking _____________________

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Origin

Deliveries or Performance _________________________

DOC SUPPL

REL CD MILSTRIP ADDR SIG CD MARK FOR TP CD ______ ________ ______ ______ ________ _____

001 BMDA7N6209D205 BXXUBQ L 2

PROJ CD BRK BLK PT _______ __________

BMDA00

DEL REL CD QUANTITY DAYS AFTER AWARD __________ ______________ ________________

001 1 0090

FOB POINT: Origin

SHIP TO:

(BMDA00) SEE SSI

0009 VECTOR 23 SPARES AND ACCESSORIES 1 PK $ $ ________________________________ ______________ __________________

8 55

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

COMMODITY NAME: SPARES FOR VECTOR 23

CLIN CONTRACT TYPE:

Firm Fixed Price

PRON: J56SAZ261G PRON AMD: 01

AMS CD: 431100

FMS COUNTRY/CASE: MD/UBQ

CLIN 0009 - See Section

3.1.0.6.4 of PWS for salient characteristics

(End of narrative B001)

Packaging and Marking _____________________

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Origin

Deliveries or Performance _________________________

DOC SUPPL

REL CD MILSTRIP ADDR SIG CD MARK FOR TP CD ______ ________ ______ ______ ________ _____

001 BMDA7N6209D305 BXXUBQ L 2

PROJ CD BRK BLK PT _______ __________

BMDA00

DEL REL CD QUANTITY DAYS AFTER AWARD __________ ______________ ________________

001 1 0090

FOB POINT: Origin

SHIP TO:

(BMDA00) SEE SSI

0010 USER TRAINING AND MAINTENANCE 1 LO $ _____________________________ __________________

SERVICE REQUESTED: Maintenance and User

CLIN CONTRACT TYPE:

Firm Fixed Price

PRON: J56SAZ271G PRON AMD: 01

FMS COUNTRY/CASE: MD/UBQ

CLIN 0010 - See Section

3.1.0.7 and 4.0 of PWS for salient characteristics

(End of narrative B001)

9 55

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

Inspection and Acceptance _________________________

INSPECTION: Destination ACCEPTANCE: Destination

DEL REL CD QUANTITY DAYS AFTER AWARD __________ ______________ ________________

001 1 0365

10 55

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

SECTION C - DESCRIPTION/SPECIFICATIONS/WORK STATEMENT

Performance Work Statement

Foreign Military Sales (FMS)

Cases MD-B-UBN Ln 6 MD-B-UBA Lns 1-6

Day and Night Imaging Sensors

18 October 2016

Communications-Electronics Command (CECOM), Security Assistance Management Directorate (SAMD)

Aberdeen Proving Ground, MD 21005

11 55

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

Table of Contents_________________

1.0 Scope _____

2.0 Applicable Documents ____________________

3.0 Requirements ____________

3.1 Products and Services _____________________

3.2 Requirements for Item Unique Item Identification (IUID) ______________________________________________________

3.3 Procurement New Production __________________________

3.4 Requirements for Packaging __________________________

3.5 Requirements for Final Inspection, Test, and Certificate of Completion ______________________________________________________________________

3.6 Requirements for Quality Assurance System _________________________________________

3.7 Safety Engineering __________________

3.8 Program Management __________________

3.9 Procurement Contracting Officer _______________________________

3.10 Certificate of Completion _________________________

4.0 Training __________

5.0 OPSEC and Security Requirements

6.0 Requirements for Travel

12 55

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

Statement of Work

For FMS Case MD-B-UBN/UBQ

1.0 Scope. This document describes the work required to be performed by the contractor to provide imaging sensors and training _____ required under Foreign Military Sales (FMS) cases MD-B-UBN and MD-B-UBQ. The word Government in this document refers to the United

States Government. The word Customer refers to the Government of Moldova.

2.0 Applicable Documents. ____________________

Military Standards

MIL-STD-130N Identification Marking of U.S. Military Property

MIL-STD-129P(4) Military Marking for Shipment and Storage

MIL-STD-882E System Safety 11 May 2012

MIL-STD-2073-1E Standard Practice for Military Packaging May 2008

Commercial Standards

ISPM 15 Regulation of Wood Packaging Material for International Trade (2009)

ASTM D 3951-98 Standard Practice for Commercial Packaging

3.0 Requirements. _____________

3.1 Products and Services _____________________

The contractor shall provide all devices and training specified in this Performance Work Statement (PWS).

3.1.0 Vectronix or equivalent products. If color choices are available, preferred is forest camouflage, second is plain green, third is _________________________________ gray or black.

3.1.0.1 VECTOR IV 3Km Laser Rangefinder or equivalent. Quantity three (3). The contractor shall provide VECTOR IV 3km laser rangefinders _____________________________________________

(day only) or equivalent. Components shall include pouch, neck strap, eyepiece protection cover, and operator manuals. A VECTOR IV laser rangefinder or its equivalent must meet or exceed the following performance characteristics.

Binocular observation

7x magnification

Field of view 120 mil/ 6.75 deg.

Objective diameter 42mm

Focus may be fixed

Engraved reticle graduation 5 mil

Electronic reticle (red LED square or similar)

Eye relief 18mm

Dioptric setting > + 4 diopter _

1064nm laser protection attenuation factor > 4 Optical Density

Laser rangefinder beam divergence 2 x 2 mil

Units meter/yard/feet

Performance at visibility 20km, 8x8m target, albedo 0.4, detection probability 90% - 3000m

Minimal distance -5m

Range capability 6000m

Laser type 1550 nm

Laser class 1 (eye-safe)

Accuracy (1 sigma) 50-2000m + 2m _

Accuracy (1 sigma) <50m/>2000m + 3m _

False alarm rate < 2%

Distance resolution on display m/yd/ft 1/1/1

Height resolution on display m/yd/ft 1/1/1

Multiple targets in line of sight 3

Min. time per measurement 0.4s

Max. time per measurement 0.9s

Max. repetition rate per minute 12

Digital magnetic compass (azimuth and inclination)

Units 6400,6300, 6000mil / 360 deg. / 400gon

Resolution on display 1mil/1deg./1gon

Azimuth accuracy (1 sigma) + 10mil / + 0.6deg _ _

Azimuth accuracy (1 sigma) with PPS calibration on tripod, typical - + 5mil/ + 0.3deg. _ _

Inclination accuracy (1 sigman) + 3mil/ + 0.2deg. _ _

Maximum inclination angle + 45 deg. _

Declination, adjustable +9999mil/ + 99.9 deg/ +99.9gon _ _ _

13 55

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

Compass calibration menu guided

Battery capacity approx. 5000 measurements (20 deg C)

Protective covering environmentally sealed, impact-resistant rubber armor casing

Operational temperature range -35 to +63 C/ -31 to +145 F

Storage temperature range (w/o battery) -40 to +65 C/ -40 to +185 F

Shock resistance 40g/11ms/xyz axes

Vibration resistance 10 to 500Hz for 10 minutes

Dimensions not to exceed 220x 190 x 90 mm/ 8.5 x 7.5 x 4 in

Tripod bushing thread

Weight (including battery) not to exceed 3kg/5.5 lbs

Interface RS232

3.1.0.2 VECTOR IV Laser Rangefinder Binocular. Quantity two (2). The contractor shall provide VECTOR IV laser rangefinders (day only) or ______________________________________ equivalent. Components shall include pouch, neck strap, eyepiece protection cover, and operator manuals. A VECTOR IV laser rangefinder or its equivalent must meet or exceed the following performance characteristics.

Binocular observation

7x magnification

Field of view 120 mil/ 6.75 deg.

Objective diameter 42mm

Focus may be fixed

Engraved reticle graduation 5 mil

Electronic reticle (red LED square or similar)

Eye relief 18mm

Dioptric setting > + 4 diopter _

1064nm laser protection attenuation factor > 4 Optical Density

Laser rangefinder beam divergence 2 x 2 mil

Units meter/yard/feet

Performance at visibility 20km, 8x8m target, albedo 0.4, detection probability 90% - 4000m

Minimal distance -5m

Range capability 6000m

Laser type 1550 nm

Laser class 1 (eye-safe)

Accuracy (1 sigma) 50-2000m + 2m _

Accuracy (1 sigma) <50m/>2000m + 3m _

False alarm rate < 2%

Distance resolution on display m/yd/ft 1/1/1

Height resolution on display m/yd/ft 1/1/1

Multiple targets in line of sight 3

Min. time per measurement 0.4s

Max. time per measurement 0.9s

Max. repetition rate per minute 12

Digital magnetic compass (azimuth and inclination)

Units 6400,6300, 6000mil / 360 deg. / 400gon

Resolution on display 1mil/1deg./1gon

Azimuth accuracy (1 sigma) + 10mil / + 0.6deg _ _

Azimuth accuracy (1 sigma) with PPS calibration on tripod, typical - + 5mil/ + 0.3deg. _ _

Inclination accuracy (1 sigman) + 3mil/ + 0.2deg. _ _

Maximum inclination angle + 45 deg. _

Declination, adjustable +9999mil/ + 99.9 deg/ +99.9gon _ _ _

Compass calibration menu guided

Battery capacity approx. 5000 measurements (20 deg C)

Protective covering environmentally sealed, impact-resistant rubber armor casing

Operational temperature range -35 to +63 C/ -31 to +145 F

Storage temperature range (w/o battery) -40 to +65 C/ -40 to +185 F

Shock resistance 40g/11ms/xyz axes

Vibration resistance 10 to 500Hz for 10 minutes

Dimensions not to exceed 220x 190 x 90 mm/ 8.5 x 7.5 x 4 in

Tripod bushing thread

Weight (including battery) not to exceed 3kg/5.5 lbs

Interface RS232

3.1.0.3 VECTOR IV Nite Laser Rangefinder Binocular with Image Intensifier Tube Technology. Quantity two (2). The contractor shall _________________________________________________________________________________ provide VECTOR IV Nite Laser Rangefinders. A VECTOR IV Nite laser rangefinder or its equivalent must meet or exceed the following performance characteristics.

14 55

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

Binocular observation

Optics daysight:

7x magnification

Field of view 120 mil/ 6.75 deg.

Objective diameter 42mm

Focus may be fixed

Engraved reticle graduation 5 mil

Electronic reticle (red LED square or similar)

Eye relief 18mm

Dioptric setting > + 4 diopter _

1064nm laser protection attenuation factor > 4 Optical Density

Optics nightsight:

Image intensifier Type DEP XD4

Monocular observation

Magnification 4.5 x

Field of view 125 mil/ 7 deg.

Limit of resolution minimum 2.6 lp/mrad

Limit of resolution typical 3.1 lp/mrad

Laser rangefinder beam divergence 2 x 2 mil

Units meter/yard/feet

Performance at visibility 20km, 8x8m target, albedo 0.4, detection probability 90% - 4000m

Minimal distance -5m

Range capability 6000m

Laser type 1550 nm

Laser class 1 (eye-safe)

Accuracy (1 sigma) 50-2000m + 2m _

Accuracy (1 sigma) <50m/>2000m + 3m _

False alarm rate < 2%

Distance resolution on display m/yd/ft 1/1/1

Height resolution on display m/yd/ft 1/1/1

Multiple targets in line of sight 3

Min. time per measurement 0.4s

Max. time per measurement 0.9s

Max. repetition rate per minute 12

Digital magnetic compass (azimuth and inclination)

Units 6400,6300, 6000mil / 360 deg. / 400gon

Resolution on display 1mil/1deg./1gon

Azimuth accuracy (1 sigma) + 10mil / + 0.6deg _ _

Azimuth accuracy (1 sigma) with PPS calibration on tripod, typical - + 5mil/ + 0.3deg. _ _

Inclination accuracy (1 sigman) + 3mil/ + 0.2deg. _ _

Maximum inclination angle + 45 deg. _

Declination, adjustable +9999mil/ + 99.9 deg/ +99.9gon _ _ _

Compass calibration menu guided

Battery capacity approx. 5000 measurements (20 deg C)

Protective covering environmentally sealed, impact-resistant rubber armor casing

Operational temperature range -35 to +63 C/ -31 to +145 F

Storage temperature range (w/o battery) -40 to +65 C/ -40 to +185 F

Shock resistance 40g/11ms/xyz axes

Vibration resistance 10 to 500Hz for 10 minutes

Dimensions not to exceed 220x 190 x 90 mm/ 8.5 x 7.5 x 4 in

Tripod bushing thread

Weight (including battery) not to exceed 3kg/5.5 lbs

Interface RS232

Each VECTOR IV Nite Rangefinder Binocular or equivalent shall include:

Objective protection cap (2x)

Tripod adapter for VECTOR Nite or equivalent

Eyepiece protection cover

Lithium battery, 6V, 2CRS, or equivalent

Neck strap

Pouch

User manual

Short instruction

15 55

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

Lens tissue

Cardboard box

Button for eye-base adjustment

Eyecup

Protection cap with cord for interface connector

Screw for battery compartment cover

O-ring seal (screw battery compartment cover)

3.1.0.4 VECTOR 21 Nite Laser Rangefinder Binocular with Image Intensifier Tube Technology. Quantity ten (10). A VECTOR 21 Nite laser _________________________________________________________________________________ rangefinder or its equivalent must meet or exceed the following performance characteristics.

Binocular observation

Optics daysight:

7x magnification

Field of view 120 mil/ 6.75 deg.

Objective diameter 42mm

Focus may be fixed

Engraved reticle graduation 5 mil

Electronic reticle (red LED square or similar)

Eye relief 18mm

Dioptric setting > + 4 diopter _

1064nm laser protection attenuation factor > 4 Optical Density

Optics nightsight:

Image intensifier Type DEP XD4

Monocular observation

Magnification 4.5 x

Field of view 125 mil/ 7 deg.

Limit of resolution minimum 2.6 lp/mrad

Limit of resolution typical 3.1 lp/mrad

Laser rangefinder beam divergence 0.4 x 0.7 mil

Units meter/yard/feet

Performance at visibility 10km, 2.3x2.3m target, albedo 0.3, detection probability 90% - 5500m

Minimal distance -5m

Range capability 12000m

Laser type 1550 nm

Laser class 1 (eye-safe)

Accuracy (1 sigma) >500m + 5m _

False alarm rate < 2%

Distance resolution on display m/yd/ft 1/1/1

Height resolution on display m/yd/ft 1/1/1

Multiple targets in line of sight 3

Min. time per measurement 0.4s

Max. time per measurement 0.9s

Max. repetition rate per minute 12

Digital magnetic compass (azimuth and inclination)

Units 6400,6300, 6000mil / 360 deg. / 400gon

Resolution on display 1mil/1deg./1gon

Azimuth accuracy (1 sigma) + 10mil / + 0.6deg _ _

Azimuth accuracy (1 sigma) with PPS calibration on tripod, typical - + 5mil/ + 0.3deg. _ _

Inclination accuracy (1 sigman) + 3mil/ + 0.2deg. _ _

Maximum inclination angle + 45 deg. _

Declination, adjustable +9999mil/ + 99.9 deg/ +99.9gon _ _ _

Compass calibration menu guided

Battery capacity approx. 5000 measurements (20 deg C)

Protective covering environmentally sealed, impact-resistant rubber armor casing

Operational temperature range -35 to +63 C/ -31 to +145 F

Storage temperature range (w/o battery) -40 to +65 C/ -40 to +185 F

Shock resistance 40g/11ms/xyz axes

Vibration resistance 10 to 500Hz for 10 minutes

Dimensions not to exceed 220x 190 x 90 mm/ 8.5 x 7.5 x 4 in

Tripod bushing thread

Weight (including battery) not to exceed 3kg/5.5 lbs

Interface RS232

16 55

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

Each VECTOR 21 Nite Rangefinder Binocular or equivalent shall include:

Battery

Neck strap

Pouch

User manual

Short instruction

Lens tissue

Button for eye-base adjustment

Eyecup

Protection cap with cord for interface connector

Screw for battery compartment cover

O-ring seal (screw battery compartment cover)

3.1.0.5 VECTOR 23 Laser Rangefinder or equivalent. Quantity two (2). Components shall include eyepiece protection cover, battery, pouch, _________________________________________ neck strap, and operator manuals, lens tissue, eyecup, protection cap with cord for interface protection, screw for battery compartment cover, O-ring seal (screw battery compartment cover). A VECTOR 23 laser rangefinder or its equivalent must meet or exceed the following performance characteristics.

Binocular observation

7x magnification

Field of view 120 mil/ 6.75 deg.

Objective diameter 42mm

Focus may be fixed

Engraved reticle graduation 5 mil

Electronic reticle (red LED square or similar)

Eye relief 18mm

Dioptric setting > + 4 diopter _

1064nm laser protection attenuation factor > 4 Optical Density

Laser rangefinder beam divergence <0.3 mil

Units meter/yard/feet

Performance at visibility 20km, 2.3 x 2.3m target, albedo 0.3, detection probability 90% - 10,200m

Minimal distance - 25m

Range capability 25,000m

Laser type 1550 nm

Laser class 1 (eye-safe)

Accuracy (1 sigma) >500m + 5m _

False alarm rate < 2%

Distance resolution on display m/yd/ft 1/1/1

Height resolution on display m/yd/ft 1/1/1

Multiple targets in line of sight 3

Min. time per measurement 0.4s

Max. time per measurement 0.9s

Max. repetition rate per minute 12

Digital magnetic compass (azimuth and inclination)

Units 6400,6300, 6000mil / 360 deg. / 400gon

Resolution on display 1mil/1deg./1gon

Azimuth accuracy (1 sigma) + 10mil / + 0.6deg _ _

Azimuth accuracy (1 sigma) with PPS calibration on tripod, typical - + 5mil/ + 0.3deg. _ _

Inclination accuracy (1 sigman) + 3mil/ + 0.2deg. _ _

Maximum inclination angle + 45 deg. _

Declination, adjustable +9999mil/ + 99.9 deg/ +99.9gon _ _ _

Compass calibration menu guided

Battery capacity approx. 5000 measurements (20 deg C)

Protective covering environmentally sealed, impact-resistant rubber armor casing

Operational temperature range -35 to +63 C/ -31 to +145 F

Storage temperature range (w/o battery) -40 to +65 C/ -40 to +185 F

Shock resistance 40g/11ms/xyz axes

Vibration resistance 10 to 500Hz for 10 minutes

Dimensions not to exceed 220x 190 x 90 mm/ 8.5 x 7.5 x 4 in

Tripod bushing thread

Weight (including battery) not to exceed 3kg/5.5 lbs

Interface RS232

3.1.0.6 Vector Night Vision Device Spares and Accessories. Offers of VECTOR devices must provide the following extra parts. Offers of _________________________________________________

VECTOR-equivalent items must provide equivalent items in the same quantities.

17 55

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

3.1.0.6.1 VECTOR IV parts. The contractor shall provide 1 package of VECTOR IV parts as follows: _______________

Description Quantity

Lithium battery 6V 20

Neck strap 20

User manual 20

Short instruction 20

Lens tissue 20

Objective cap 8

Focusing knob 2

Eyecup 40

Eyecup protection cover 2

Protection cap with interface cord 10

Screw for battery compartment cover 10

O-ring seal 10

Battery cover assembly 2

3.1.0.6.2 VECTOR IV Nite parts. The contractor shall provide 1 package of VECTOR IV Nite parts as follows: ____________________

Description Quantity

Lithium battery 6V 5

Neck strap 5

User manual 5

Short instruction 5

Lens tissue 5

Objective cap 2

Focusing knob 1

Eyecup 10

Eyecup protection cover 1

Protection cap with interface cord 5

Screw for battery compartment cover 5

O-ring seal 5

Battery cover assembly 5

3.1.0.6.3 VECTOR 21 Nite parts. The contractor shall provide 1 package of VECTOR 21 Nite parts as follows: ____________________

Description Quantity

Lithium battery 6V 10

Neck strap 10

User manual 10

Short instruction 10

Lens tissue 10

Objective cap 4

Focusing knob 1

Eyecup 20

Eyecup protection cover 1

Protection cap with interface cord 5

Screw for battery compartment cover 5

O-ring seal 5

Battery cover assembly 1

3.1.0.6.4 VECTOR 23 parts. The contractor shall provide 1 package of VECTOR 23 parts as follows: _______________

Description Quantity

Lithium battery 6V 10

Neck strap 10

User manual 10

Short instruction 10

Lens tissue 10

Objective cap 4

Focusing knob 1

Eyecup 20

Eyecup protection cover 1

Protection cap with interface cord 5

18 55

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

Screw for battery compartment cover 5

O-ring seal 5

Battery cover assembly 1

3.1.0.7 Services Training. The contractor shall provide OCONUS maintenance training. Training will be for 2 days with a maximum of 10 ___________________ students at a suitable facility of the customer countrys choosing. Classes will be taught in English. If an interpreter is required it will be the countrys responsibility to provide one. The training shall cover parts and accessories removal and replacement, based on the spares/accessories packages of paragraph 3.1.0.6.

3.2 Requirements for Item Unique Identification (IUID). The contractor shall mark all contract deliverables In Accordance With (IAW) __________________________________________________

DFARS clause 252.211-7003 in Section I of this contract and the following requirements.

3.2.1 IUID Marking.

3.2.1.1. New items: The contractor shall provide IUID, or DoD recognized equivalent, for all items delivered with an acquisition unit cost of $5000 or more. For long term contracts, any items that have range quantity prices established that will exceed the $5000 unit price shall have IUID markings from the beginning of the contract. IUID markings shall be IAW MIL-STD-130N.

3.2.1.2. Repair items: The contractor shall mark those items as identified by the Government. Items received for repair shall be inspected for IUID markings. Those items where the marking is damaged or missing the contractor shall mark the equipment. When marking requirements are not clearly specified then the contractor shall advise the Procurement Contracts Officer (PCO). For previously acquired items where the IUID markings were not required the contractor shall follow the procedures as if the item was a new item.

3.2.1.3 Commercial Markings. All other items shall have acceptable commercial markings that meet the guidelines in Department of

Defense (DoD) Guide to Uniquely Identifying Items: http://www.acq.osd.mil/dpap/pdi/uid/index.html.

3.2.1.4 Permanency and Legibility. The IUID marking and identification plates, tags, etching, or labels when used on equipment, parts, assemblies, subassemblies, units, sets, groups, or kits shall be as permanent as the normal life expectancy of the item and be capable of withstanding the environment, test, cleaning, repair, and rebuild procedures specified for the item. Legibility shall be as required and verified for ready readability per MIL-STD-130N.

3.2.1.5 Deleterious Effect. Marking of items shall be accomplished in a manner that will not adversely affect the life and utility of the item. Marking materials creating hazardous conditions shall not be used. Placement and choice of the marking shall not create hazardous conditions.

3.2.2 IUID Coding. IUID markings and readability requirements shall comply with MIL-STD-130N.

3.2.2.1 Symbology markings and the order of priority for marking the hardware shall be in accordance with MIL-STD-130N. First priority is the 2D data matrix symbol (machine readable) IUID is the minimum requirement when there are severe space limitations. The second priority is the human readable characters. The third priority is the Linear Bar Code.

3.2.2.1.1 The vendor who is supporting an FMS purchase shall adhere to MIL-STD-130N during the application of serial numbers on all systems. The system serial numbers shall be provided to Communications-Electronics Command (CECOM) Security Assistance Management

Directorate (SAMD) point of contact Contract Officers Representative (COR) in electronic format prior to delivery of all hardware items to country or country freight forwarder.

3.2.2.2 If the technical data has not specified the marking location, markings shall be located such that they are visible during item use, provided that sufficient space is available, and does not interfere with equipment operations.

3.2.2.3. The contractor shall maintain an accurate, current list of IUIDs for all manufactured items on this contract. Dates of manufacture, substitutions, shop changes, etc. shall be included on this list. The list shall be available for inspection by the

Procurement Contracts Officer (PCO) or other Government representative at any time during the life of this contract. The contractor shall provide this list to the government at the end of the contract.

3.2.3 Correction of Noncompliant Equipment and Technical Data.

3.2.3.1 If this contract contains configuration control requirements, the contractor shall initiate the appropriate configuration control document to correct all affected drawings/specifications which conflict with or omit the marking requirements stipulated above.

3.2.3.2 If the item on order is defined by existing Government technical documentation and such documentation is in conflict with the requirements of this PWS, production of equipment with revised markings shall not proceed until Government approval is received.

3.2.4 Pricing of IUID Requirements. All efforts required by this PWS and contract, including, but not limited to, the preparation of

Engineering Change Proposals (ECPs) or notification of marking deficiencies, Property In the Possession of the Contractor (PIPC) reporting, serial number data reporting at end of contract and the actual marking of hardware, will be included in the base contract

19 55

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

price.

3.3. Procurement New Production. All hardware shall be supplied from new production and shall be the latest configuration at time of ____________________________ production.

3.4. Requirements for Packaging: Packaging/packing shall be in accordance with ASTM D3951-98, Standard Practice for Commercial __________________________

Packaging, Level of Protection (LOP); Commercial, Level of Pack (LPK); Commercial, Quantity Unit Pack (QUP); 001. Marking shall be in accordance with MIL-STD-129P. Radio Frequency Identification (RFID) Requirements shall be IAW Section F clause. DFARS 252.211-7006, of the contract. MIL-STD-129P is applicable.

3.4.1 Wood Packaging Material (WPM) shall meet the following requirements:

3.4.1.1. Wood packaging material (WPM) includes but is not limited to pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. This requirement excludes materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and Oriented Stranded Board (OSB).

3.4.1.2. All WPM shall meet the requirements of International Standards for Phytosanitary Measures (ISPM) Number 15, Regulation of Wood

Packaging Material for International Trade (2009). DoD shipments inside and outside of the United States shall meet the requirements of

ISPM 15 whenever WPM is used to ship DoD cargo.

3.4.1.3. All WPM shall comply with the official quality control program for heat treatment (HT) or kiln dried heat treatment (KD HT)

(IAW) American Lumber Standard Committee (ALSC), Incorporated, Wood Packaging Material Program and WPM Enforcement Regulations (see

://www.alsc.org/).

3.4.1.4. All WPM shall include certification/quality markings IAW the ALSC standard. Markings shall be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides of the pallet and be contrasting and clearly visible. All containers shall be marked on a side other than the top or bottom, contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ASLC approved DUNNAGE stamp.

3.4.1.5. Failure to comply with these requirements may result in refusal, destruction, or treatment of materials at the point of entry.

The Government reserves the right to recoup from the contractor any remediation costs incurred by the Government.

3.4.2. Handling, Storage, Preservation, Packaging and Shipping. The Contractor shall establish, maintain, control and be responsible for the handling, storage, preservation, packaging and shipping to protect the quality of the materials and to prevent damage from loss, deterioration, degradation, or substitution of products.

3.5 Requirements for Final Inspection, Test, and Certification of Completion. The contractor shall comply with the following ________________________________________________________________________ requirements:

3.5.1. Sites for Inspection, Testing and Acceptance. Inspection, testing and acceptance of Products listed in paragraphs 3.1.0 and 3.1.5 ____________________________________________ specify shall be at origin. Inspection and testing shall be performed by the contractor. Acceptance shall be by a DCMA Quality

Assurance Representative (QAR) verifying Part Description and count, via Wide Area Work Flow (WAWF).

3.5.2 Inspection and Testing. The contractor shall assure that all necessary inspections and tests are performed on completed products, ______________________ and this shall include all inspections and tests which are normally performed for the equipment on order. The contractor shall as a minimum perform any inspections and tests (including visual/mechanical inspections and functional tests) required to satisfy the form, fit, and function requirements of the contract. The form, fit, and function requirements are defined by the contractors drawings and literature (specification sheets, brochures, technical manuals, etc).

3.5.3 Certificate of Completion. Acceptance of Services (Services paragraphs 3.1.1, 3.1.2, 3.1.3, and 3.1.4). The contractor shall __________________________ attach a completed Certificate of Completion to each DD Form 250 submitted for services in the WAWF system in accordance with CDRL A001 for DI-MISC-80711A and this PWS. The report shall present data as described below:

a. As a minimum, the contractor shall provide the following using the template below:

1) Contractor Information. Contract information, to include but not limited to:

a. Contract number

b. Delivery Order Number (if applicable)

c. Contract CLIN

d. FMS Case designator

e. Service being invoiced

f. Class roster (for training services)

g. Contractor Point of contact for certificate of completion to include, printed name, position/title/rank, phone number, email and signature certifying completion.

20 55

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

2) Verifying persons information that can verify the services have been completed to include but not limited to Country/customer/US

Government Personnel, point of contact for certificate of completion to include, printed name, position/title/rank, phone number, email address and signature verifying completion.

Failure to provide all the information as indicated in this paragraph could result in payment delays.

Certificate of Completion Template

Company letterhead.

Date:______________________

Subject:______________________________

Customer:________________________________

Contract Number:_____________________________

Delivery Order Number:___________________________

FMS Case Designator:_______________________

Contract CLIN:________________________________________________

Period and service invoiced:____________________________________________________

If Applicable, Include Class Roster:___________________________________________

IF Applicable (check one) __ less than 80% __between 80-90% __ above 90% of students successfully completed training

Customer Comments:

Contractor Representative Customer/Government Representative

Printed Name:________________________ Printed Name:________________________

Title:________________________________ Title:________________________________

Email: _______________________________ Email: _____________________________

Date:________________________________ Date:________________________________

Signature Signature

3.5.4 Responsibility. The requirements of this PWS do not relieve the contractor of the responsibility to perform any additional tests ______________ or inspections required to assure product quality and compliance with drawings and specification requirements.

3.6 Requirements for Quality Assurance System. The contractor shall implement and maintain a Quality Assurance System for commercial __________________________________________ items that meets or exceeds commercial best practices. These established commercial quality requirements shall be commonly accepted practices employed by industry in both national and international manufacturing environments. The contractor shall comply with the following requirements in addition to their best practice commercial quality assurance system.

3.6.1 Quality System. The contractor shall establish/maintain a system for the final inspection and test of all purchased items to ______________ comply with contract or order requirements.

3.6.2 Records. The contractor shall maintain adequate records of inspections and tests to demonstrate that the final product satisfies _______ contract requirements. These records shall be made available to the government upon request.

3.6.3 Measuring, Testing, and Inspection Equipment. The contractor shall provide and maintain gages (including production tooling used ____________________________________________ for inspection purposes) and other measuring and testing equipment to assure that finished products conform to contract requirements.

These devices shall be calibrated against certified measurement standards, which are traceable back to national/international standards.

3.6.4 Nonconforming Material . The contractor shall maintain controls for material, which does not satisfy contract or order ______________________ requirements, including procedures for the identification, segregation, and disposition (rework/repair, scrap, etc.).

3.6.5 Corrective Action . The contractor shall promptly act to correct nonconforming materials and conditions to satisfy contract or _________________ order requirements and prevent the recurrence of this problem. 3.6.6 Handling, Storage, Preservation, Packaging, and Shipping . The ________________________________________________________ contractor shall control the handling, storage, preservation, packaging, and shipping to protect the quality of finished products.

3.6.7 Government Quality Assurance. Any in-process inspections performed by the Government shall be conducted in a manner consistent ______________________________ with contractors commercial practices.

3.7 Safety Engineering. The contractor shall identify all real and potential hazards associated with the equipment ordered on this ___________________ contract. This shall include any toxic substance exposure concerns to personnel during operation or maintenance to include transportation or resulting from damage to the equipment. The contractor shall also identify any special disposal procedures. The identified hazards and special disposal procedures shall be described either in the applicable Technical Manual shipped with each hardware item, or alternatively as a separate insert (in English) included with each hardware item if no Technical Manual is available for the item. All hazards that cannot be eliminated shall be reduced to lowest risk possible. Those hazards that cannot be eliminated

21 55

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

must be presented to the contracting officer, providing as a minimum the post and pre-fix hazard severity and hazard probability levels, corrective action and status, prior to government acceptance of the equipment. MIL-STD-882D shall be used in assessing system safety.

The contractor shall affix applicable safety/hazardous precautionary warnings on hardware in English.

3.8 Program Management. The contractor shall designate a program manager who will have overall responsibility for the control and ___________________ coordination of all work performed. The program manager will act as the single point of contact within the contractors activity for all required program status information.

3.9 Procurement Contracting Officer The Aberdeen Proving Ground (APG) Army Contracting Center (ACC) Procurement Contracting Officer _______________________________

(PCO) is the single point of contact within the government for funds and program direction. Only the PCO can approve or direct changes or additions to the contract.

4.0 Training. Training shall be provided per the requirements of paragraphs 3.1.0.7. _________

4.1 Training Materials. Student courseware materials shall be provided for each student and shall consist of Course Evaluation Forms , ___________________ a student guide, performance tests, overhead presentation transparencies (and/or electronic media), and pertinent equipment manual. All student courseware material shall be provided in the language of instruction. One (1) copy of the training plan and the student courseware material, in English, shall be provided at least 30 days prior to the training in accordance with Contract Data Requirement

List (CDRL) B001 for DI-SESS-81523B and this PWS.

4.2 Student Evaluation Report. The contractor shall submit a Student Evaluation Report, in accordance with CDRL B002 for DI-SESS-81523B _________________________ and this PWS. This report shall detail the effectiveness of training in terms of test scores and other methods employed in the contractors standard course materials. Course Evaluation Forms shall be submitted.

5. Security and OPSEC Requirements.___________________________________

5.1 Foreign subcontractor participation will be handled in accordance with AR 380-10 (Technology Transfer, Disclosure of Information &

Contacts with Foreign Representatives); Department of Defense Manual Number 5220.22, Volume 3 April 17, 2014 (National Industrial

Security Program: Procedures for Government Activities Relating to Foreign Ownership, Control, or Influence (FOCI)); DoD Directive

5230.11 (Disclosure of Classified Military Information to Foreign Governments and International Organizations.)

5.2 Anti-terrorism (AT). ____________________

5.2.1 All contractor employees, to include subcontractor employees, requiring access Army installations, facilities and controlled access areas shall complete AT Level I awareness training within 30 calendar days after contract start date or effective date of incorporation of this requirement into the contract, whichever is applicable. The contractor shall submit certificates of completion for each affected contractor employee and subcontractor employee, to the COR or to the contracting officer, if a COR is not assigned, within

30 calendar days after completion of training by all employees and subcontractor personnel. AT level I awareness training is available at the following website: https://jkodirect.jten.mil/ for CAC holders. Non-CAC-holders may go to:

http://jko.jten.mil/courses/atl1/launch.html.

5.2.2 AT Awareness Training for US Based Contractors Traveling Overseas. All US based contractor and sub-contractor employees required to travel overseas to receive government provided area of responsibility (AOR) specific AT awareness training as directed by AR 525-13.

Specific AOR training content is directed by the combatant commander with the unit Anti-Terrorism Officer (ATO) being the local point of contact.