A2_-_SOW_-_70hp_Outboard_Motors_&_Rigging.pdf

SCOPE OF WORK

Service to Replace Twin 70hp Outboard Motors & Rigging/Steering

Snagboat SNELL July 18, 2018

1. GENERAL: The Contractor shall furnish all Labor, Materials, and Services, to provide the U.S. Army Corps of Engineers, Wilmington District, Snagboat SNELL with (1) set of Twin 70hp Outboard Motors, to include the Rigging/Steering components, Labor for installation, and Delivery to the Engineer Repair Yard.

2. SPECIFICATIONS: The engines & rigging shall meet the specifications listed below:

TWIN OUTBOARD MOTORS

• 70hp Twin 4-Stroke Outboard Motors

• 16-valve, single overhead camshaft (SOHC), in-line 4 cylinder engine

• Electric Start & PT

• Multi-point Fuel Injection

• On-engine Fuel / Water Separator

• additional exterior 10-Micron Fuel / Water separating filter (2)

• 20’ shafts

• NTE 275 lbs each / 550 lbs both engines (dry weight)

• Fresh water flushing connection

• (2) Stainless Steel Propellers

• 3yr Government Warranty

RIGGING

• 6YC Display w/ Mechanical Twin Engine Binnacle Control

• 20’ Main Bus Harness, Rear Hub to Front Hub

• 3’ Pigtail Harness, Front Hub to Gauges

• Shift & Throttle Cables (4)

• Front mount Hydraulic Steering Ram w/ all stainless fittings necessary to install

• New Hydraulic Hoses to go to the existing Helm

• Tie Bar Kit for Twin Engine Application

The Vessel will be delivered to the contractors’ facility by a Corps of Engineers employee.

Upon completing the installation of the Twin Outboards & Rigging/Steering components listed above, the contractor shall deliver the vessel to the Wilmington District, Engineer Repair Yard (sec. 4).

CLIN# DESCRIPTION UNIT QTY TOTAL COST

Purchase & Install Twin 70hp Outboard Motors with compatible Rigging/Steering components, plus Labor for Installation, and delivery.

JOB 1

Quote should be all inclusive

Figure 1: Vessel to be installed on.

Figure 2: Vessel to be installed on. (Stern)

3. CONTRACT / TECHNICAL POC: U.S. Army Corps of Engineers

Wilmington District

ATTN: SCOTT AIKEN

69 Darlington Avenue Wilmington, NC 28403-1343

4. DELIVERY: U.S. Army Corps of Engineers Wilmington District Engineer Repair Yard Attn: KEN BAILEY or Assignee 232 Battleship Road Wilmington, NC 28401

5. PERIOD of PERFORMANCE: 30 days from Contract Award Date

6. INVOICING: Invoices shall be submitted via email to: michael.s.aiken@usace.army.mil

INVOICES ONLY

OR through the United States Postal Service (USPS) to the Contract / Technical POC (sec. 3)

THE CONTRACTOR SHALL ALSO ENSURE THAT THE FOLLOWING ITEMS ARE INCLUDED ON THE INVOICE:

• CONTRACT #

• INVOICE #

• COMPANY NAME (MUST MATCH THE NAME ON THE CONTRACT DOCUMENT)

• INVOICED LINE ITEM(S) MUST MATCH THE CONTRACT LINE ITEMS (E.G. 0001, 0002, ETC.)

• SMALL BUSINESS, VETERAN OWNED, OR 8A (INDICATE ON INVOICE, IF APPLICABLE)

7. AT-OPSEC REFERENCE:

15. Pre-screen candidates using E-Verify Program. Proposed language: "The Contractor must pre-screen Candidates using the E-verify Program (http://www.uscis.gov/e-verify) website to meet the established employment eligibility requirements. The Vendor must ensure that the Candidate has two valid forms of Government issued identification prior to enrollment to ensure the correct information is entered into the E-verify system. An initial list of verified/eligible Candidates must be provided to the COR no later than 3 business days after the initial contract award." *When contracts are with individuals, the individuals will be required to complete a Form I-9, Employment Eligibility Verification, with the designated Government representative.

This Form will be provided to the Contracting Officer and shall become part of the official contract file.

mailto:michael.s.aiken@usace.army.mil