TECHNICAL ORDERING DATA.pdf

MATERIAL ORDERING DATA

MIL-S-1222

IDN: 4523A 4061-8300

ICN: 38J0159644 KO: S05 KOI: 006

Paragraph 6.2 Ordering Data

A. MIL-S-1222H, STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATIONS WHERE A

HIGH DEGREE OF RELIABILITY IS REQUIRED; GENERAL SPECIFICATION FOR; dated 21 OCT 1986. AMENDMENT 3, dated 30 SEP 1994.

B. Type - Studs: Select One:, Nuts: Select One:, Bolts: Select One:, Screws:

Type II - Hex sockets head cap

Style - Studs: Select One:, Nuts: Select One:

Material Grade: QQ-N-286

Heat Treatment or Condition of Fasteners: N/A

(see 1.2, 3.1, 3.2, and Table I, II, III, or IV)

C. Grade 400 should not be cold drawn and stress relieved (see 3.1.2.2). NA

D. Permeability test, if required for annealed corrosion resistant (300 series) steel (see 3.3): NA

E. Decarburization, if other than specified (see 3.6): NA

F. Type of coating, if required (see 3.7): NA

G. Size: .3125"

Length (for studs, bolts and screws) thread series: 2.25"LG, 18UNRC

Class of fit: 3A

(see 3.8.1, 3.8.2.1, 3.8.2.2, 3.8.3, 3.8.4, 3.8.5 and 3.8.6)

H. Bearing surface (see 3.8.3 and 3.8.6): N/A (Bolts/Nuts. Unless otherwise specified, the bearing surface shall be either washer faced or chamfered.)

I. Identification, if other than specified (see table I and 3.9):

J. Whether lot (a) or (b) is required or whether special sampling is required (see 4.2, 4.2.1, 4.3):

K. Government acquistions, Packaging, packing and marking (see 5.1). Fasteners shall be preserved-packaged level A or C packed level A, B, or C as specified, and marked in accordance with PPP-H-1581, except that externally threaded fasteners over 5/6 inch nominal diameter shall be furnished with thread protectors or other suitable cushioning.

L. Test report is required (see 4.5).

Additional Data Requirements:

SCREW, SOCKET CAP, K-500, .3125-18 X 2.25 LG

QQ-N-286, MIL-S-1222 AMN 3

8900127102, C-51-L05-36-UD

CHEMICAL/MECHANICAL CERTS REQUIRED

Prepared By: WAYNE BOOHER

Code: C/127.2

6.2.2 Data Requirements. When this specification is used in an acquisistion and data are required to be delivered, the data requirements identified below shall be developed as specified by an approved Data Item Despcription (DD Form 1664) and elivered in accordance with the papproved Contract Data Requirements List (CDRL), incorporated into the contract. When the provisions of DOD FAR Supplement, Part 27, Sub-Part 27.410-6 (DD Form 1423) are invoked and the DD Form 1423 is not used, the data specified below shall be delivered by the contractor in accordance with the contract or prucahsed order requirements. Deliverable data required by this specification is cited in the following paragraph.

Parahgraph no. Data requiremtns title Applicable DID no. Option

4.5 Reports, test DI-T-2072 ---

4.5 Certification data for non- DI-MISC-80705 nuclear level I material

(Data item decriptions related to this specification, and identified in section 6 will be approved and listed as such in DoD 5010.12-L., Vol. 1, AMSDL. Copies of data item descrptions required by the contractors in connection with specific acquisition functions should be obtained from the Naval Publications and Forms Center or as directed by the contracting officer.)

6.2.2.1 The data requirements of 6.2.2 and any task in sections 3, 4, or 5 of this specification required to be peformed to meet a data requirement may be waived by the contracting/acquisition activity upon certication by the offeror that identical data were submitted by the offeror and accepted by the Government under a previous contract for identical item acquired to this specification. This does not apply to specific data which may be required for each contract regardless of whether an identical item has been supplied previously (for example, test reports).

IDN: 4523A 4061-8310

ICN: 38J0159644 KO: S05 KOI: 005

Paragraph 6.2 Ordering Data

A. MIL-S-1222H, STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATIONS WHERE A

G. Size: .3125"

Length (for studs, bolts and screws) thread series: 1.50"LG, 18UNRC

(Bolts/Nuts. Unless otherwise specified, the bearing surface shall be either washer faced or chamfered.)

SCREW, SOCKET CAP,

K-500, QQ-N-286, MIL-S-1222 AMN 3

.3125-18 X 3A UNRC 1.50 LG

8900127101, C-51-L05-24-UD

approved Data Item Despcription (DD Form 1664) and elivered in accordance with the papproved Contract Data Requirements List (CDRL), incorporated into the contract. When the provisions of DOD FAR Supplement, Part 27, Sub-Part 27.410-6 (DD Form 1423) are invoked and the DD Form 1423 is not used, the data specified below shall be delivered by the contractor in accordance with

(Data item decriptions related to this specification, and identified in section 6 will be approved and contractors in connection with specific acquisition functions should be obtained from the Naval Publications and Forms Center or as directed by the contracting officer.)

6.2.2.1 The data requirements of 6.2.2 and any task in sections 3, 4, or 5 of this specification required to be peformed to meet a data requirement may be waived by the contracting/acquisition activity upon certication by the offeror that identical data were submitted by the offeror and accepted by the Government under a previous contract for identical item acquired to this

IDN: 4523A 4061-8311

ICN: 38J0159644 KO: S05 KOI: 004

Paragraph 6.2 Ordering Data

A. MIL-S-1222H, STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATIONS WHERE A

G. Size: .250"

Length (for studs, bolts and screws) thread series: 1.75"LG, 20UNRC

(Bolts/Nuts. Unless otherwise specified, the bearing surface shall be either washer faced or chamfered.)

SCREW, SOCKET CAP, K-500, .250-20 X3A UNRC 1.75 LG

QQ-N-286, MIL-S-1222 AMN 3

8900151108, C-51-L04-28-UD

approved Data Item Despcription (DD Form 1664) and elivered in accordance with the papproved Contract Data Requirements List (CDRL), incorporated into the contract. When the provisions of DOD FAR Supplement, Part 27, Sub-Part 27.410-6 (DD Form 1423) are invoked and the DD Form 1423 is not used, the data specified below shall be delivered by the contractor in accordance with

(Data item decriptions related to this specification, and identified in section 6 will be approved and contractors in connection with specific acquisition functions should be obtained from the Naval Publications and Forms Center or as directed by the contracting officer.)

6.2.2.1 The data requirements of 6.2.2 and any task in sections 3, 4, or 5 of this specification required to be peformed to meet a data requirement may be waived by the contracting/acquisition activity upon certication by the offeror that identical data were submitted by the offeror and accepted by the Government under a previous contract for identical item acquired to this

IDN: 4523A 4061-8312

ICN: 38J0159644 KO: S05 KOI: 003

Paragraph 6.2 Ordering Data

A. MIL-S-1222H, STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATIONS WHERE A

G. Size: .250"

Length (for studs, bolts and screws) thread series: .88"LG, 20UNRC

(Bolts/Nuts. Unless otherwise specified, the bearing surface shall be either washer faced or chamfered.)

SCREW, SOCKET CAP, K-500, .250-203A UNRC X .88 LG

QQ-N-286, MIL-S-1222 AMN 3

8900151107, C-51-L04-14-UD

approved Data Item Despcription (DD Form 1664) and elivered in accordance with the papproved Contract Data Requirements List (CDRL), incorporated into the contract. When the provisions of DOD FAR Supplement, Part 27, Sub-Part 27.410-6 (DD Form 1423) are invoked and the DD Form 1423 is not used, the data specified below shall be delivered by the contractor in accordance with

(Data item decriptions related to this specification, and identified in section 6 will be approved and contractors in connection with specific acquisition functions should be obtained from the Naval Publications and Forms Center or as directed by the contracting officer.)

6.2.2.1 The data requirements of 6.2.2 and any task in sections 3, 4, or 5 of this specification required to be peformed to meet a data requirement may be waived by the contracting/acquisition activity upon certication by the offeror that identical data were submitted by the offeror and accepted by the Government under a previous contract for identical item acquired to this