Tech Data.pdf

DISASTER BLANKET

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL

AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

7210-00-119-5335

ITEM DESCRIPTION - BLANKET, DISASTER

REQUIREMENTS

DESCRIPTION - THIS ITEM COVERS BLANKETS INTENDED

FOR USE IN OR BY INSTITUTIONS FOR DISASTER RELIEF

PURPOSE WHERE WARMTH AND COMFORT ARE DESIRABLE

CHARACTERISTICS. THE BLANKET CAN BE ANY COLOR

THAT DOES NOT SHOW DIRT OR STAINS WELL

AND SHALL BE MADE FROM 100% ACRYLIC OR 30%

(PLUS OR MINUS 5%) WOOL AND THE REMAINDER 70%

(PLUS OR MINUS 5%) MAN-MADE FIBER, ACETATE FIBER,

WOVEN OR NON-WOVEN MUST BE NAPPED IN ORDER TO

PROVIDE A WARM, COMFORT SOFT-FEEL. THE BLANKET

SHALL MEASURE NOT LESS THAN 66 INCHES WIDE AND 90

INCHES LONG AND WEIGH NOT LESS THAN 2.5 POUNDS

(TOTAL WEIGHT PER BLANKET). ALL EDGES OF THE

BLANKET THAT DO NOT HAVE A SELVEDGE SHALL BE

FINISHED WITH A 1/4(+/-1/16) INCH OVER-EDGE STITCHED

HEM WITH NOT LESS THAN 10 STITCHES PER INCH.

EITHER COTTON, COTTON- BLENDED OR SYNTHETIC

THREAD MAY BE USED FOR ALL STITCHING. THE ENDS

OF THE OVER-EDGE STITCHING MUST NOT UNRAVEL.

REGULATORY REQUIREMENTS - THE CONTRACTOR IS

ENCOURAGED TO USED RECOVERED MATERIAL IN

ACCORDANCE WITH PUBLIC LAW

94-580 TO THE MAXIMUM EXTENT PRACTICABLE.

LABEL - EACH BLANKET MUST BE LABELED IN

ACCORDANCE WITH APPLICABLE RULES AND

REGULATION UNDER THE TEXTILE FIBER PRODUCT

ACT, WOOL PRODUCTS LABELING ACT AND CARE

LABEL ACT. THE LABEL MUST CONTAIN THE

FOLLOWING: BLANKET, DISASTER, (ACRYLIC

CONTENT, WOOL CONTENT, NON-ACRYLIC CONTENT,

EXPRESSED AS PERCENTAGES)CONTRACTOR'S NAME,

CONTRACT NUMBER, NATIONAL STOCK NUMBER (NSN)

AND THE FOLLOWING STATEMENT: "THIS BLANKET

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

CONTAINS NO DDT. DO NOT DRY CLEAN OR

LAUNDER". SEE EXAMPLE.

WORKMANSHIP - AFTER COMPLETION, THE FINISHED

BLANKET SHALL NOT BE COMPOSED OF MORE THAN

ONE PIECE, SHALL BE CLEAN, AND ALL LOOSE THREAD,

LINT, AND FOREIGN MATTER REMOVED. THE

FINISHED BLANKET SHALL BE EXAMINED FOR

COMMERCIAL DEFECTS LISTED BELOW.

EXAMINATION - BLANKET LOTS SHALL BE

INSPECTED IN ACCORDANCE WITH "SAMPLING

PROCEDURES AND TABLES FOR INSPECTION BY

ATTRIBUTES", ANSI/ASQC Z1.4 PUBLISHED BY

THE AMERICAN SOCIETY FOR QUALITY CONTROL.

COMMERCIAL DEFECTS - ANY SPOT OR STAIN

CLEARLY VISIBLE AT NORMAL INSPECTION

DISTANCE ( APPROXIMATELY 3 FEET); ANY

RANCID OR OBJECTIONABLE ODOR; ANY HOLE,

CUT OR TEAR; ANY

ABRASION OR THIN PLACE; SMASH OR MEND;

BROKEN OR MISSING

YARN; UNEVENLY NAPPED; EDGES FOLDED,

ROLLED OR SCALLOPED

RAW EDGE; SKIPPED STITCHED OR TIGHT

OR LOOSE STITCHES.

LABEL - EACH BLANKET MUST BE LABELED IN

ACCORDANCE WITH APPLICABLE RULE AND REGULATION

UNDER THE TEXTILE FIBER PRODUCT ACT, WOOL

PRODUCTS LABELING ACT AND CARE LABEL ACT.

THE LABEL MUST CONTAIN THE FOLLOWING:

BLANKET, DISASTER, (ACRYLIC CONTENT, WOOL

CONTENT, NON-ACRYLIC CONTENT, EXPRESSED AS PERCENTAGES)CONTRACTOR'S NAME, CONTRACT

NUMBER, NATIONAL STOCK NUMBER (NSN) AND THE

FOLLOWING STATEMENT: "THIS BLANKET CONTAINS NO DDT.

DO NOT DRY CLEAN OR LAUNDER". SEE EXAMPLE.

NUMBER, NATIONAL STOCK NUMBER (NSN) AND THE

FOLLOWING STATEMENT:

LABEL EXAMPLE:

DISASTER BLANKET

60 % ACRYLIC 10% WOOL 30% REPROCESSED

CONTRACTOR'S NAME

CONTRACT NUMBER

7210-00-119-5335

THIS BLANKET CONTAINS NO DDT

DO NOT DRY CLEAN OR LAUNDER

PACKAGING, PACKING, PALLETIZATION AND MARKING-

EACH BLANKET SHALL BE PACKAGED IN A CLEAR

POLYETHYLENE FILM BAG AND PACKED EIGHT BLANKETS

PER CARTON IN ACCORDANCE WITH ASTM D-3951,

AS SPECIFIED FOR THE DEPARTMENT OF THE DEFENSE.

SHIPPING CONTAINERS SHALL BE UNITIZED IN

ACCORDANCE WITH ASTM-D- 3951 TO INCLUDE A

FOUR WAY ENTRY WING TYPE PALLET MEASURING

40 INCHES LONG BY 48 INCHES WIDE, WITH LOAD

NOT TO EXCEED 54 INCHES IN HEIGHT, PALLET

INCLUDED. SHIPPING CONTAINERS SHALL BE

SNUG-FITTING WITH A BOX LINER CONFORMING

TO TYPE CF, CLASS DOMESTIC VARIETY DW,

GRADE 275. THE FLUTE OF THE LINER SHALL BE

PERPENDICULAR TO THE TIP OF THE BOX.

UNITIZED LOAD SHALL BE SECURED TO PALLET BY

MEANS OF SHRINK OR STRETCH WRAP.

UNITS(EACH POLY BAGGED BLANKET), SHIPPING

CONTAINER, AND UNITIZED LOADS SHALL BE MARKED

IN ACCORDANCE WITH MIL-STD-129.

INSPECTION OF SUPPLIES SHALL BE IN ACCORDANCE WITH FAR PART 52.246-2 STANDARD

INSPECTION.

ADDITIONAL INFORMATION FOR MIL-STD-105E:

MIL-STD-105E, dated 10 May 1989, is hereby canceled.

Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product," or ANSI/ASQ Z1.4, "Sampling Procedures and Tables for Inspection by Attributes."

Users are cautioned to evaluate these documents for their particular application before citing it as a replacement document.

(Copies of MIL-STD-1916 are available online at http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

(Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207-6028.)

MIL-STD-129R - DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED 18 FEBRUARY 2014

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL

BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS,

REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS

"PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147E

w/CHANGE 1 23 December 2013

SUPERSEDING

MIL-STD-147E

16 May 2008

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

ADDITIONAL INFORMATION: FED-STD-751 HAS BEEN

CANCELLED AND REPLACED BY ASTM-D-6193, 4/98

STANDARD PRACTICES FOR STITCHES AND SEAMS.

THIS STANDARD SHOULD BE USED IN PREFERENCE

http://assist.daps.dla.mil/ http://www.asq.org/

TO FED-STD-751.

(ref. T0216 - May 18, 2006)

This device or drug is regulated by the FDA.

Note to Buyer: The Government contracting official shall submit a pre-award survey request, through email, to product specialist.

FIVE EACH FIRST ARTICLE

SAMPLES OF THE END ITEM(S) BE SUBMITTED TO THIS

CENTER FOR VISUAL AND DIMENSIONAL EXAMINATIONS.