SPRPA1-20-R-W265.pdf

CAUTION TO OFFERORS - NO CONTRACT WILL BE AWARDED UNDER

THIS SOLICITATION AT GREATER THAN FAIR AND REASONABLE PRICES.

SECTION A - COVER SHEET

(See Section L of the Table of Contents in

You are cautioned to note the "Certification of Non-Segregated Facilities" in the solicitation. Failure to agree to the certification will render your reply nonresponsive to the terms of solicitations involving awards of contracts exceeding $25,000 which are not exempt from the provisions of the Equal Opportunity clause.

"Fill-ins" are provided on the face and reverse of Standard Form 18 and Parts I and IV of Standard Form 33, or other solicitation documents and Sections of Table of Contents in this solicitation and should be examined for applicability.

See the provision of this solicitation entitled "Late Bids, Modifications of Bids or Withdrawal of Bids" or "Late Proposals, Modifications of Proposals and Withdrawals of Proposals."

When submitting your reply,the envelope used must be plainly marked with the Solicitation Number, as shown above and the date and local time set forth for bid opening or receipt of proposals in the solicitation document.

If NO RESPONSE is to be submitted, detach this sheet from the solicitation, complete the information requested on reverse,fold, affix postage, and mail. NO ENVELOPE IS NECESSARY.

Replies must set forth full, accurate, and complete information as required by this solicitation The penalty for making false statements is prescribed in 18 U.S.C.1001.

(X one).

a. SEALED BID

c. NEGOTIATED (RFQ)

INSTRUCTIONS

NOTE THE AFFIRMATIVE ACTION REQUIREMENT OF THE EQUAL OPPORTUNITY CLAUSE WHICH MAY APPLY TO THE CONTRACT

RESULTING FROM THIS SOLICITATION.

3. ISSUING OFFICE

(including attachments).

4. ITEMS TO BE PURCHASED

5 PROCUREMENT INFORMATION

a. THIS PROCUREMENT IS UNRESTRICTED

b. THIS PROCUREMENT IS A ______% SET-ASIDE FOR ONE OF THE FOLLOWING

1. SOLICITATION NUMBER

INFORMATION TO OFFERORS OR QUOTERS

6. ADDITIONAL INFORMATION

(1) Small Business (2) Labor Surplus Area Concerns (3) Combined Small Business/Labor Area Concerns

DD Form 1707, MAR 89 Previous editions are obsolete.

(Brief description)

(Complete mailing address, including Zip Code)

(X one) this solicitation for details of the set-aside.)

(X and complete as applicable)

461/089

2.

b. NEGOTIATED (RFP)

7. POINT OF CONTACT FOR INFORMATION

a. NAME (Last, First, Middle Initial) b. ADDRESS (Include Zip Code)

c. TELEPHONE NUMBER (Include Area Code and Extension) (NO COLLECT CALLS)

SPRPA1-20-R-W265

X 20086-0018

DLA AVIATION AT PHILADELPHIA, PA

DLR PROCUREMENT OPERATIONS (AP)

700 ROBBINS AVENUE BUILDING 1

PHILADELPHIA PA 19111-5098

SEE SCHEDULE

X

R. RAUCHEISEN APAC.26

DLA AVIATION AT PHILADELPHIA, PA

(215) 737-7063 PHILADELPHIA PA 19111-5098

KKKKKKKKKKKKKKKKKKKJ

KKKKKKKKKKKKKKKKKKKJ

e. OTHER

8. REASONS FOR NO RESPONSE

DD Form 1707 Reverse, MAR 89

(1) Typed or Printed Name

d. DO NOT REGULARLY MANUFACTURE OR SELL THE TYPE OF ITEMS INVOLVED

b. CANNOT MEET DELIVERY REQUIREMENT

c. UNABLE TO IDENTIFY THE ITEM(S)

a. CANNOT COMPLY WITH SPECIFICATIONS

9. MAILING LIST INFORMATION

WE DESIRE TO BE RETAINED ON THE MAILING LIST FOR FUTURE PROCUREMENT OF THE TYPE OF ITEM(S) INVOLVEDYES NO

10. RESPONDING FIRM

a. COMPANY NAME b. ADDRESS

c. ACTION OFFICER

(4) Date Signed

AFFIX

STAMP

HERE

(X all that apply)

FROM

DATE (YYMMDD)

SOLICITATION NUMBER

LOCAL TIME TO

(Last, First, Middle Initial) (YYMMDD)

(2) Title (3) Signature

FOLDFOLD

FOLD FOLD

(Specify)

(X one)

(INCLUDE ZIP CODE)

SPRPA1-20-R-W265

2020 MAY 13 02:00 P.M.

or if handcarried, in the depository located in until local time (Date)

9. Sealed offers in original and copies for furnishing the supplies or services in the Schedule will be received at the place specified in Item 8, IV

III

III

INSTRS., CONDS., AND NOTICES TO OFFERORS

21. ACCOUNTING AND APPROPRIATION20. AMOUNT19. ACCEPTED AS TO ITEMS NUMBERED

SOLICITATION

M

M

M

Prescribed by GSA FAR (48 CFR) 53.214(c)

EVALUATION FACTORS FOR AWARD

REPRESENTATIONS, CERTIFICATIONS AND

OTHER STATEMENTS OF OFFERORS

LIST OF ATTACHMENTS

CONTRACT CLAUSES

M L

K

J

I

SEC. DESCRIPTION PAGE(S)

SPECIAL CONTRACT REQUIREMENTS

CONTRACT ADMINISTRATION DATA

DELIVERIES OR PERFORMANCE

INSPECTION AND ACCEPTANCE

H G F E D C B A

PACKAGING AND MARKING

DESCRIPTION/SPECS./WORK STATEMENT

SUPPLIES OR SERVICES AND PRICES/COSTS

SOLICITATION/CONTRACT FORM

14. ACKNOWLEDGMENT OF AMENDMENTS

opposite each item, delivered at the designated point(s), within the time specified in the schedule.

from the date for receipt of offers specified above, to furnish any or all items upon which prices are offered at the price set

(60 calendar days unless a different12. In compliance with the above, the undersigned agrees, if this offer is accepted within ______ calendar days

CODE

(Signature of Contracting Officer)

10. FOR INFORMATION

CALL:

(Type or print)

11. TABLE OF CONTENTS

33-132

(If other than Item 7)24. ADMINISTERED BY

CODE

STANDARD FORM 33

IMPORTANT - Award will be made on this Form, or on Standard Form 26, or by other authorized official written notice.

25. PAYMENT WILL BE MADE BY

(If other than Item 7)8. ADDRESS OFFER TO

NSN 7540-01-152-8064

PREVIOUS EDITION NOT USABLE

7. ISSUED BY

RATING PAGE OF

PAGESSOLICITATION, OFFER AND AWARD

2. CONTRACT NO. 5. DATE ISSUED 6. REQUISITION/PURCHASE NO.4. TYPE OF SOLICITATION

A. NAME B. TELEPHONE NO. (Include area code) (NO COLLECT CALLS)

15A. NAME

AND

ADDRESS

OF

OFFEROR

16. NAME AND TITLE OF PERSON AUTHORIZED TO SIGN OFFER

(TYPE OR PRINT)

18. OFFER DATE17. SIGNATURE15B. TELEPHONE NO. (Include areacode) 15C. CHECK IF REMITTANCE ADDRESS

IS DIFFERENT FROM ABOVE - ENTER

SUCH ADDRESS IN SCHEDULE

27. UNITED STATES OF AMERICA 28. AWARD DATE

AWARD

(Hour)

NEGOTIATED (RFP)

CODE CODE

FACILITY

NOTE: Item 12 does not apply if the solicitation includes the provisions at 52.214-16, Minimum Bid Acceptance Period.

26. NAME OF CONTRACTING OFFICER

13. DISCOUNT FOR PROMPT PAYMENT

3. SOLICITATION NO.

period is inserted by the offeror)

(See Section I, Clause No. 52-232-8)

(The offeror acknowledges receipt of amendments to the SOLICITATION for offerors and related doc-uments numbered and dated:

10 CALENDAR DAYS 20 CALENDAR DAYS 30 CALENDAR DAYS CALENDAR DAYS

AMENDMENT NO. DATE AMENDMENT NO. DATE

SEC. PAGE(S)DESCRIPTION

(To be completed by Government)

1. THIS CONTRACT IS A RATED ORDER

UNDER DPAS (15 CFR 350)

SEALED BID (IFB)

NOTE: In sealed bid solicitations "offer" and "offeror": mean "bid" and "bidder".

CAUTION - LATE Submissions, Modifications, and Withdrawals: See Section L, Provision No. 52.214-7 or 52.215-10. All offers are subject to all terms and conditions contained in this solicitation.

(REV. 4-85)

22. AUTHORITY FOR USING OTHER THAN FULL AND OPEN COMPETITION:

M ITEM23. SUBMIT INVOICES TO ADDRESS SHOWN IN(4 copies unless otherwise specified)41 U.S.C. 253(c)( )10 U.S.C. 2304(c)( )

OFFER (Must be fully completed by offeror)

PART - THE SCHEDULE PART - CONTRACT CLAUSES

PART - LIST OF DOCUMENTS, EXHIBITS AND OTHER ATTACH.

PART - REPRESENTATIONS AND INSTRUCTIONS

DO-C9 1 65

SPRPA1-20-R-W265 X 2020 APR 28 20086-0018

SPRPA1

DLA AVIATION AT PHILADELPHIA, PA

DLR PROCUREMENT OPERATIONS (AP)

700 ROBBINS AVENUE BUILDING 1

PHILADELPHIA PA 19111-5098

BLDG 1 ROOM 2223 02:00PM 2020 MAY 13

R. RAUCHEISEN APAC.26 (215) 737-7063

X 1 X 26 X 2 X 3 X 45

X 7 X 17

X 20 X 45 X 23 X 62 X 25 X 64

PAGES

OFPAGEREFERENCE NO. OF DOCUMENT BEING CONTINUED

NAME OF OFFEROR OR CONTRACTOR

CONTINUATION SHEET

ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

SPRPA1-20-R-W265 2 65

0001 NSN 6KH 8145-01-676-8213 YR

BASE,SHIPPING AND S SHELF LIFE 0-00

SEE TECHNICAL REQUIREMENTS IN SECTIONS C, D, E, AND ATTACHMENTS

HM QUP ICQ PMT CD PM WM CUD CT UC LP IC UCL SP MK PACK UNIT PKWT UNIT PKCU OPI

N 001 000 10 1 00 00 00 0 00 A 00 A 00 FFF 0.0 0.000 M

PACKAGING IS IN ACCORDANCE WITH MIL-STD-2073

SHIP TO

0001AA N00383-20-X-1884 W62G2T 25 EA

TP: 3

0001AB FIRST ARTICLE TEST 1 LO NSP

(GOVERNMENT - NON-DESTRUCTIVE)

SOLICITATION NOTES:

Offerors are advised that offers received from sources which are not government-approved sources of supply will be deemed technically unacceptable, and therefore ineligible for award. Any distributors of approved source(s) MUST submit a copy of their authorized distributor letter, on the source's letterhead, to the buyer point of contact indicated on the solicitation via email, at time of proposal submittal.

INSPECTION AT ORIGIN

ACCEPTANCE AT ORIGIN

POC FAX: (215) 737-7149

POC EMAIL: RACHEL.RAUCHEISEN@DLA.MIL

SPRPA1-20-R-W265 PAGE 3 OF 65

PART I - THE SCHEDULE

SECTION B

SUPPLIES OR SERVICES AND PRICES/COSTS

WSSTERMBZ04

IMPORTANT NOTICE REGARDING HAZARDOUS MATERIAL

FAR clause 52.223-3, Hazardous Material Identification and Material Safety Data, is incorporated by reference in Section I in this solicitation and requires offerors to--

(1) identify and hazardous material (defined in FED STD 313 as an item or chemical which is a "health or physical hazard" per OSHA in 29 CFR 1910.1200) that will be delivered under a resultant contract, and

(2) provide a Material Safety Data Sheet meeting OSHA/FED STD 313 requirements for all hazardous material identified.

While not an all-inclusive listing of hazardous material, at a minimum, any item with a four-digit Federal Supply Code (FSC), which correlates to the first four positions of the National Stock Number (NSN), of 6810, 6820, 6830, 6840, 6850,7930, 8010, 8030, 8040, 9110, 9135, 9140, 9150, or 9160 is considered hazardous material and requires submission of a Material Safety Data Sheet or an appropriate representation that there is no hazardous material contained in theitem.

Failure to provide the required information and documentation may render you ineligible for award. If you have questions about whether a solicited tiem is classified as hazardous, contact the NAVSUP WSS HAZMAT point of contact, NAVSUPWSS Code 0772, at (717) 605-1361. (10-06)

PART I - THE SCHEDULE

SECTION C

DESCRIPTION/SPECIFICATIONS/WORK STATEMENT

CLIN: 0001

NIIN: 016768213 ACTIVITY USE ONLY: TDP VERSION NO.: 002

ITEM NAME: BASE,SHIPPING AND S

1. SCOPE

1.1 PRE-AWARD / POST AWARD REQUIREMENTS:

Due to the critical use of this item and its quality history, a pre-award survey and post-award conference may be required for all new manufacturers. For all previous sources, a post-award conference may be recommended.

1.2 Container shell material is <ALUMINUM> .

1.3 When discrepancies exist between these requirements and those on current manufacturer's drawings,contact code <BUYER ON PAGE 1 OF CONTRACT> or code N241.10

1.4 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with <CONTAINER RESEARCH CORPORATION> drawing number ( <05259> ) <923E001> , Revision <LATEST> and all details and specifications referenced therein.

1.5 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.

1.6 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.

2. APPLICABLE DOCUMENTS

2.1

DRAWING NO. CAGE REV DOC TYPE DISTR CD SHEET NR REV TYPE SIZE

923E001 05259 D

3. REQUIREMENTS

SPRPA1-20-R-W265 PAGE 4 OF 65

3.1 One third (1/3) unit of desiccant (MIL-D-3464, Type II nondusting) per cubic foot of container interior volume shall be placed in desiccant holder of each container at time of shipment.

3.2 Reference to Cadmium plating shall be deleted and the following substituted: "Finish shall be electrodeposited alkaline Zinc-Nickel Alloy in accordance with ASTM B 841 Class 1, Type B, Grade 3." All containers must be affixed with a nameplate that includes a Unique Identification (UID) marking as referenced in the drawing package Drawing <(80132) 15930> and IAW Mil-STD-130 latest revision. The contractor shall contact NAVICP code <BUYER FOUND ON PAGE 1 OF CONTRACT> or code 0771.10 for the alphanumeric sequential serial number group that makes up part of the UID.

The UIDwill be included on the nameplate in data matrix format.

3.3 Surface Finishing. All containers shall be glass bead blasted on exterior surfaces only to provide a uniform matte finish that will hide minor surface imperfections, such as scratches, weld irregularities, etc. Size #8 glass beads per MIL-G-9954 shall be used with direct air pressure ranging from 50 to 70 PSIG. A Separator shall be used to provide a reclaim efficiency of 90%, i.e., a minimum of 90% by weight of the original sized material shall be in the reclaim. The glass bead media shall be maintained in a condition free from contamination with other metals, i.e., The media shall not have been used to blast equipment containing other metals or alloys. Contact code <BUYER ON PAGE 1 OF CONTRACT> or code N241.10 to arrange for First Article Test location When a First Article is required, the contractor shall submit a paper copy of the drawings (size 11" X 17"), contracts and approved ECP's ECO's, deviations waivers, and modifications in the records recepticle or inside the container submitted for the First Article.

3.4 Welding and welder qualifications shall be in accordance with AWS D1.1 for steel, AWS D1.2 or MIL-W-22248,Class 4 for aluminum, AWS D1.3 for sheet steel and AWS D1.6 for stainless steel. Proper controls shall be used to prevent melt through or burn through. For aluminum, filler for welding 6061 alloy shall be 4043: filler for welding 5000 series alloys to themselves or to 6061 shall be 5356 or 5556. In addition,welding and weld inspection shall include:

(1) Visual inspection shall include 5X (5power) magnification when a suspect condition is to be examined beyond the capability of normal vision.

(2) Critical and major welds may be subjected to further non destructive testing (such as dye penetrant inspection)as prescribed by the buying activity.

(3) Proper documentation shall be available for review by Government personnel.

3.5 WORK INSTRUCTIONS. Work instructions shall be posted at theoperator's work station giving procedures to control the welding process, i.e., filler material, weld size, electrical and gas characteristics, including flow rate.

3.6 MATERIALS AND MATERIALS CONTROL. The quality program shall assure that the materials used in fabrication or processing, i.e., base metals and weld filler material, be inspected and conform to the applicable physical, chemical and other technical requirements (supplier's certification is sufficient).

3.7 CONTROLS. Weld filler materials shall be clearly identified and segregated from each other both when in storage and at the work station. Work station environment shall be controlled to prevent conditions adverse to proper gas shielding.

3.8 CLEANING. Parts to be welded shall be cleaned to remove surface soils such as oils, waxes, grease, inks, etc.

except that uninhibited alkaline solutions such as sodium hydroxide shall NOT be used.

3.9 DEOXIDIZING. The cleaned parts shall be chemically deoxidized NO MORE THAN 10 DAYS PRIOR TO WELDING to remove thick surface oxide films. (If the material or work is exposed to an outdoor environment, this time limit shall be reduced to a maximum of 3 days, to account for atmospheric effects.) Mechanical cleaning methods shall be applied just prior to the actual start of welding, to remove any reoxidation or residual thin oxide films.

3.9.1 CHEMICAL TREATMENT. An acid deoxidizing treatment shall be applied by either immersion or brushing/wiping.

Deoxidizers acceptable for use shall include nitric acid, sulfuric chromic, phosphoric chromic, or equivalent solutions. Sodium hydroxide solutions shall not be used. Care shall be taken to assure 100% solution coverage of the area to be welded. To allow an adequately sized deoxidized area for good welding, the solution shall be applied to an area extending at least 2 inches from the weld site, or ending at any closer adjacent edge.

3.9.2 MECHANICAL MEANS. Immediately prior to welding, mechanical cleaning methods shall be applied to the weld areas previously chemically treated to assure removal of residual or reformed oxides, if any. Acceptable methods of mechanical cleaning include stainless steel wire brushing, scraping, filing, or sanding. However, abrasives containing iron and its oxides, steel wool and wire, and copper alloy based wire, which may become embedded with galvanically active metals and accelerate corrosion of aluminum alloys shall NOT be used. Mechanical methods shall be vigorous enough to adequately remove any residual oxide films, but gentle enough to avoid forming an excessively rough surface in the comparatively soft metal underneath. Welding and welder qualifications shall meet current AWS D1.2 standards.

Additionally, cleaning preperations shall be in accordance with MIL-C-5541 and the cleaning paragraph located in the welding requirements section of the contract

252.211-7005

SUBSTITUTIONS FOR MILITARY OR FEDERAL SPECIFICATIONS AND STANDARDS (NOV 2005)

SPRPA1-20-R-W265 PAGE 5 OF 65

252.211-7005 (CONT)

SUBSTITUTIONS FOR MILITARY OR FEDERAL SPECIFICATIONS AND STANDARDS (NOV 2005)

(a) Definition.

"SPI process," as used in this clause, means a management or manufacturing process that has been accepted previously by the Department of Defense under the Single Process Initiative (SPI) for use in lieu of a specific military or Federal specification or standard at specific facilities. Under SPI, these processes are reviewed and accepted by a Management Council, which includes representatives of the Contractor, the Defense Contract Management Agency, the Defense Contract Audit Agency, and the military departments.

(b) Offerors are encouraged to propose SPI processes in lieu of military or Federal specifications and standards cited in the solicitation. A listing of SPI processes accepted at specific facilities is available via the Internet at http://guidebook.dcma.mil/20/guidebook_process.htm (paragraph 4.2).

(c) An offeror proposing to use an SPI process in lieu of military or Federal specifications or standards cited in the solicitation shall-

(1) Identify the specific military or Federal specification or standard for which the SPI process has been accepted:

(2) Identify each facility at which the offeror proposes to use the specific SPI process in lieu of military or Federal specifications or standards cited in the solicitation;

(3) Identify the contract line items, subline items, components, or elements affected by the SPI process;

and

(4) If the proposed SPI process has been accepted at the facility at which it is proposed for use, but is not yet listed at the Internet site specified in paragraph (b) of this clause, submit documentation of Department of Defense acceptance of the SPI process.

(d) Absent a determination that an SPI process is not acceptable for this procurement, the Contractor shall use the following SPI processes in lieu of military or Federal specifications or standards:

(Offeror insert information for each SPI process)

SPI Process:_________________________________________________________________

Facility:____________________________________________________________________

Military or Federal Specification or Standard:___________________________________________________

Affected Contract Line Item Number, Subline Item Number, Component, or Element:_______________________________________________________

(e) If a prospective offeror wishes to obtain, prior to the time specifie d for receipt of offers, verification that an SPI process is an acceptable replacement for military or Federal specifications or standards required by the solicitation, the prospective offeror:

(1) May submit the information required by paragraph (d) of this clause to the Contracting Officer prior to submission of an offer; but

(2) Must submit the information to th Contracting Officer at least 10 working days prior to the date specified for receipt of offers.

WSSTERMCZ01

CONFIGURATION MANAGEMENT

(a) The Contractor shall maintain the total baseline configuration of the contract items, including, but not limited to, hardware, software and firmware, in accordance with the configuration management provisions of this contract.

(b) Definitions

(1) Critical Application Item (CAI) - CAI is defined as an item that is essential to weapon system performance or operation, or the preservation of life or safety of operational personnel, as determined by the military services. The subset of CAIs, whose failure could have catastrophic or critical safety consequences (Category I or II as defined by MIL-STD-882), are Critical Safety Items (CSI).

(2) Critical Safety Item (CSI) - CSI is defined as a part, an assembly, installation, or production system with one or more critical or critical safety characteristics that, if missing or not conforming to the design data, quality requirements, or overhaul and maintenance documentation, would result in an unsafe condition that could cause

SPRPA1-20-R-W265 PAGE 6 OF 65

WSSTERMCZ01 (CONT)

CONFIGURATION MANAGEMENT

loss or serious damage to the end item or major components, loss of control, un-commanded engine shutdown, or serious injury or death to personnel and unsafe conditions, which relate to hazard severity categories I and II of MIL-STD-882, System Safety Requirements. CSIs are a subset of CAIs and include, but are not limited to, items determined to be life-limited, fracture critical, or fatigue sensitive. A Critical Safety Item may also be known by terms such as a Flight Safety Critical Aircraft Part, Flight Safety Part, or Flight Safety Critical Part. For purposes of this contract, the term used will be Critical Safety Item.

(3) Engineering Change Proposal (ECP) - An ECP is the documentation by which an engineering change and its implementation for items to be delivered under this contract is proposed, justified and submitted to the appropriate authority for approval or disapproval. Class I and Class II ECPs will be classified as follows:

(i) Class I ECP. An engineering change will be classified as Class I if:

(A) it affects any physical or functional requirement in approved functional or configuration documentation, or

(B) it affects any approved functional, allocated or product configuration documentation, cost to the

Government, warranties or contract milestones, or

(C) it affects approved product configuration documentation and one or more of the following:

Government furnished equipment (including Government test equipment and associated programs such as Test Program Sets/Software); safety; compatibility, interoperability, or logistic support; delivered technical manuals for which changes are not funded; will require retrofit of delivered units; preset adjustments or schedules affecting operating limits or performance to the extent a new identification number is required; interchangeability, substitutability, or replacement of any item down to non-repairable assemblies, sources on a source control drawing; or skills manning, training, biomedical factors or human engineering design.

(ii) Class II ECP. An engineering change is Class II if it does not impact any of the Class I factors specified above.

(4) Deviation - A deviation is the specific written authorization to depart from a particular requirement of the item's configuration for a specific number of units or for a specific amount of time. It is also a specific written authorization to accept items, which are found to depart from specified requirements, but which nevertheless is considered suitable for use "as is" or after correction by a specified method. The term deviation encompasses what previously had been defined as both a deviation and waiver, and therefore includes requests to depart from a known requirement before, during or after manufacture. Deviations will be classified as follows:

(i) Major. A deviation is major when it involves a departure from requirements or specifications involving: health, performance, interchangeability, reliability, survivability, maintainability or durability of the item or parts, effective use or operation of the item or system, weight or size, and appearance (when a factor).

(ii) Critical. A deviation is critical when the deviation involves or impacts safety.

(iii) Minor. A deviation is minor when the deviation does not involve factors listed above for either critical or major deviations.

(c) Configuration Management/ECPs

(1) The Government will maintain configuration control and change authority for all modifications or changes affecting form, fit, function, or interface parameters of the contract items and sub-assemblies. Guidelines for preparing Class I and Class II ECPs may be found in MIL-HDBK-61A, Configuration Management Guidance and ANSI/EIA-649, National Consensus Standard for Configuration Management. The Contractor will maintain configuration of the items in accordance with the requirements of this contract.

(2) The Contractor shall submit an Engineering Change Proposal (ECP) for any Class I or II changes that impact the items covered by this contract. An ECP shall be designated Class I or Class II, as defined in this contract.

(i) If the Contractor has an ECP pending with another Government activity, has an approved ECP that the Contractor proposes to incorporate under this contract, or has an ECP pending or approved under a production contract, the Contractor will notify the PCO of the status of the ECP and provide a copy of the ECP submission. Any such Class I ECPs, however, will be incorporated only by modification to the contract.

(ii) A properly documented ECP submitted under this contract shall be processed as follows:

(A) Any Class I ECP must be submitted to the contracting officer for approval/disapproval. A Class I change will be not be implemented until a contract modification is issued by the contracting officer.

(B) Any Class II ECP involving a non-critical item or a CAI shall be submitted to the cognizant

Defense Contract Management Agency (DCMA) for concurrence in classification and may be implemented only upon receiving DCMA concurrence. Any Class II ECP involving a CSI must be clearly identified as involving a CSI, must be submitted to the contracting officer for review by the contracting officer and the Navy's Basic Design Engineer, and may be implemented only upon the approval of the contracting officer. If, however, authorized in writing by the contracting officer or if the Naval Air Systems Command has delegated authority in writing to the DCMA to concur in Class II ECPs involving CSIs for the Contractor (which is specific to the Contractor's location and CAGE code), a Class II ECP involving a CSI may be submitted to the DCMA and implemented upon DCMA's concurrence with classification. If the affected Class II ECP item or items have not been identified as CAI, CSI or as non-critical by the Government, the Contractor will contact the contracting officer to obtain a classification for the affected items. The Government will not be responsible for any contract delay or disruption or any increased costs of performance of the contractor due to a misclassification of an ECP by the contractor, including those costs associated with replacement of delivered items resulting from such a misclassification. Class II changes shall be made at no additional cost to the Government.

(iii) The Contractor shall coordinate with the cognizant NAVAIR PMA office prior to any ECP submission.

The Contractor will provide copies of configuration changes affecting FMS customers to NAVICP FMS, Code P751.

(iv) Under this contract, a Class I ECP may be prepared in the contractor's format but in a medium compatible with Government information management systems. In addition, a Class I ECP shall provide all information

SPRPA1-20-R-W265 PAGE 7 OF 65

WSSTERMCZ01 (CONT)

CONFIGURATION MANAGEMENT

required by DI-CMAN-80639C - Engineering Change Proposal. A Class II ECP may be prepared in the contractor's format.

The minimum required data is: name and part number of item affected; name and part number of next higher assembly;

description of the engineering change; need and reason for the change; all government contract numbers for which the change applies; and the change document number. Justification codes are not required for Class II ECPs.

(v) The contractor is not entitled to any equitable adjustment to the contract price or terms based on the Government's disapproval of a Class I or Class II ECP.

(d) Configuration Management/Deviations

(1) The Contractor shall not manufacture any item for acceptance by the Government that incorporates a known departure from technical or contractual requirements unless a request for a deviation has been approved. Authorized deviations are a temporary departure from the requirements only and do not authorize a change to the item's configuration baseline.

(2) Deviation requests shall be prepared in accordance with DI-CMAN-80640C - Request for Deviation.

Guidelines for preparing deviations may also be found in MIL-HDBK-61A, Configuration Management Guidance and ANSI/EIA-649, National Consensus Standard for Configuration Management.

(3) Major, critical and minor deviations are classified in accordance with the definitions in this contract.

(4) A Request for Deviation shall be processed as follows upon submission of a properly documented request:

(i) For items involving a major or critical deviation, delivery and/or shipment of such items under this contract is not permitted until authorized in writing by the contracting officer.

(ii) For any such non-critical item or CAI involving a minor deviation, delivery and/or shipment of such items under this contract is not permitted until authorized by the cognizant DCMA. Minor deviations affecting CSI must be identified as involving a CSI, must be submitted to the contracting officer for review by the contracting officer and the Navy's Basic Design Engineer, and may be delivered only upon the approval of the contracting officer. If, however, authorized in writing by the contracting officer or if the Naval Air Systems Command has delegated authority in writing to the DCMA to approve minor deviations involving CSIs for the Contractor (which is specific to the Contractor's location and CAGE code), a minor deviation affecting a CSI may be reviewed by the DCMA and may be delivered if authorization from DCMA is received. If the affected item or items have not been identified as CAI, CSI or as non-critical by the Government, the Contractor will contact the contracting officer to obtain a classification for the affected items.

(5) Recurring deviations are discouraged and shall be minimized. The contractor is not entitled to any equitable adjustment to the contract price or terms based on the Government's disapproval of a major/critical or minor deviation. In addition, the Government may be entitled consideration from the contractor if a deviation is approved. (10-04)

PART I - THE SCHEDULE

SECTION D

PACKAGING AND MARKING

CLIN: 0001

NIIN: 016768213 ACTIVITY USE ONLY: TDP VERSION NO.: 002

ITEM NAME: BASE,SHIPPING AND S

5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE

252.211-7003

ITEM UNIQUE IDENTIFICATION AND VALUATION (MAR 2016)

(a) Definitions. As used in this clause --

"Automatic identification device" means a device, such as a reader or interrogator, used to retrieve data encoded on machine-readable media.

"Concatenated unique item identifier" Means --

(1) For items that are serialized within the enterprise identifier,the linking together of the unique identifier data elements in order of the issuing agency code, enterprise identifier, and unique serial number within the enterprise identifier; or

(2) For items that are serialized within the original part, lot, orbatch number, the linking together of the unique identifier data elements in order of the issuing agencycode; enterprise identifier; original part, lot, or batch number; and serial number within the original part, lot, or batch number

"Data matrix" means a two-dimensional matrix symbology, which is made up of square or, in some cases, round modules arranged within a perimeter finder pattern and uses the Error Checking and Correction 200 (ECC200) specification found within International Standards Organization (ISO)/International Electrotechnical Commission (IEC) 16022.

SPRPA1-20-R-W265 PAGE 8 OF 65

252.211-7003 (CONT)

ITEM UNIQUE IDENTIFICATION AND VALUATION (MAR 2016)

"Data qualifier" means a specified character (or string of characters) that immediately precedes a data field that defines the general category or intended use of the data that follows.

"DoD recognized unique identification equivalent" means a unique identiification method that is in commercial use and has been recognized byDoD. All DoD recognized unique identification equivalents are listed at http://www.acq.osd.mil/dpap/pdi/uid/iuid_equivalents.html.

"DoD item unique identification" means a system of marking items deliveered to

DoD with unique item identifiers that have machine-readable data elements to distinguish an item from all other like and unlike items. For items that are serialized within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier and a unique serial number. For items that are serialized within the part, lot, or batch number within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier; the original part, lot, or batch number; and the serial number.

"Enterprise" means the entity (e.g., a manufacturer or vendor) responsible for assigning unique item identifiers to items.

"Enterprise identifier" means a code that is uniquely assigned to an enterprise by an issuing agency.

"Governments unit acquisition cost" means --

(1) For fixed-price type line, subline, or exhibit line items, the unit price identified in the contract at the time of delivery;

(2) For cost-type or undefinitized line, subline, or exhibit line items, the Contractors estimated fully burdened unit cost to thee Government at the time of delivery; and

(3) For items produced under a time-and-materials contract, the Contractors estimated fully burdened unit cost to the Government at the time of delivery.

"Issuing agency" means an organization responsible for assigning a globally unique identifier to an enterprise, as indicated in the Register of Issuing Agency Codes for ISO/IEC 15459, located at http://www.aimglobal.org/?Reg_Authority15459.

"Item" means a single hardware article or a single unit formed by a grouping of subassemblies, components, or constituent parts.

"Lot or batch number" means an identifying number assigned by the enterprise to a designated group of items, usually referred to as either a lot or a batch, all of which were manufactured under identical conditions.

"Machine-readable" means an automatic identification technology media, such as bar codes, contact memory buttons, radio frequency identification, or optical memory cards.

"Original part number" means a combination of numbers or letters assigned by the enterprise at item creation to a class of items with the same form, fit, function, and interface.

"Parent item" means the item assembly, intermediate component, or subasssembly that has an embedded item with a unique item identifier or DoD recognized unique identification equivalent.

"Serial number within the enterprise identifier" means a combination off numbers, letters, or symbols assigned by the enterprise to an item that provides for the differentiation of that item from any other like and unlike item and is never used again within the enterprise.

"Serial number within the part, lot, or batch number" means a combinatiion of numbers or letters assigned by the enterprise to an item that provides for the differentiation of that item from any other like item within a part, lot, or batch number assignment.

"Serialization within the enterprise identifier" means each item produced is assigned a serial number that

SPRPA1-20-R-W265 PAGE 9 OF 65

ITEM UNIQUE IDENTIFICATION AND VALUATION (MAR 2016)

is unique among all the tangible items produced by the enterprise and is never used again. The enterprise is responsible for ensuring unique serialization within the enterprise identifier.

"Serialization within the part, lot, or batch number" means each item of a particular part, lot, or batch number is assigned a unique serial number within that part, lot, or batch number assignment. The enterprise is responsible for ensuring unique serialization within the part, lot, or batch number within the enterprise identifier.

"Type designation" means a combination of letters and numerals assignedd by the Government to a major end item, assembly or subassembly, as appropriate, to provide a convenient means of differentiating betweenitems having the same basic name and to indicate modifications and changes thereto.

"Unique item identifier" means a set of data elements marked on items tthat is globally unique and unambiguous. The term includes a concatenated unique item identifier or a DoD recognized unique identificationequivalent.

"Unique item identifier type" means a designator to indicate which method of uniquely identifying a part has been used. The current list ofaccepted unique item identifier types is maintained at http://www.acq.osd.mil/dpap/pdi/uid/uii_types.html.

(b) The Contractor shall deliver all items under a contract line, subline, or exhibit line item.

(c) Unique item identifier.

(1) The Contractor shall provide a unique item identifier for the following:

(i) Delivered items for which the Governments unit acquisition cost is $5,000 or more, except for the following line items:

Contract Line, Subline, or Exhibit Line Item Number Item Description

(ii) Items for which the Governments unit acquisition cost is less than $5,000 that are identified in the Schedule or the following table:

Contract Line, Subline, or Exhibit Line Item Number Item Description

(If items are idenified in the Schedule, insert "See Schedule" in this table.)

(iii) Subassemblies, components, and parts embedded within delivered items, items with warranty requirements, DoD serially managed reparables and DoD serially managed nonreparables as specified in Attachment Number < > .

(iv) Any item of special tooling or special test equipment as defined in FAR 2.101 that have been designated for preservation and storage for a Major Defense Acquisition Program as specified in Attachment Number < >

(v) Any item not included in (i), (ii), (iii), or (iv) for which the contractor creates and marks a unique item identifier for traceability.

(2) The unique item identifier assignment and its component data element combination shall not be duplicated on any other item marked or registered in the DoD Item Unique Identification Registry by the contractor.

SPRPA1-20-R-W265 PAGE 10 OF 65

ITEM UNIQUE IDENTIFICATION AND VALUATION (MAR 2016)

(3) The unique item identifier component data elements shall be marked onan item using two dimensional data matrix symbology that complies with ISO/IEC International Standard 16022, Information technology Interrnational symbology specification Data matrix; ECC200 data matrix sppecification.

(4) Data syntax and semantics of unique item identifiers. The Contractor shall ensure that --

(i) The data elements (except issuing agency code) of the unique item identifier are encoded within the data matrix symbol that is marked on the item using one of the following three types of data qualifiers, as determined by the Contractor:

(A) Application Identifiers (AIs) (Format Indicator 05 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology EAN/UCC Appliccation Identifiers and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier Standard.

(B) Data Identifiers (DIs) (Format Indicator 06 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology EAN/UCC Application Ideentifiers and Fact Data Identifiers and Maintenance and ANSI MH10.8.2 Data Identifier and Application Identifier Standard.

(ii) The encoded data elements of the unique item identifier conform to the transfer structure, syntax, and coding of messages and dataformats specified for Format Indicators 05, 06, and 12 in ISO/IECInternational Standard 15434, Information Technology Transfer Syyntax for High Capacity Automatic Data Capture Media.

(5) Unique item identifier.

(i) The Contractor Shall --

(A) Determine whether to --

(1) Serialize within the enterprise identifier;

(2) Serialize within the part, lot, or batch number; or

(3) Use a DoD recognized unique identification equivalent (e.g. Vehicle Identification Number); and

(B) Place the data elements of the unique item identifier (enterprise identifier; serial number;

DoDrecognized unique identification equivalent; and for serialization within the part, lot, or batch number only:

original part, lot, or batch number) on items requiring marking by paragraph (c)(1) of this clause, based on the criteria provided in MIL-STD-130, Identification Marking of U.S. Military Property, latest version;

(C) Label shipments, storage containers and packages that contain uniquely identified items in accordance with the requirements ofMIL-STD-129, Military Marking for Shipment and Storage, latest version; and

(D) Verify that the marks on items and labels on shipments, storagecontainers, and packages are machine readable and conform to the applicable standards. The contractor shall use an automatic identification technology device for this verification that has been programmed to the requirements of Appendix A, MIL-STD-130,latest version.

(ii) The issuing agency code --

(A) Shall not be placed on the item; and

(B) Shall be derived from the data qualifier for the enterprise identifier.

(d) For each item that requires item unique identification under paragraph (c)(1)(i), (ii), or (iv) of this clause or when item unique identification is provided under paragraph (c)(1)(v), in addition to the information provided as part of the Material Inspection and Receiving Report specified elsewhere in this contract, the Contractor shall report at the time of delivery, as part of the Material Inspection and Receiving Report, thefollowing information:

(1) Unique item identifier.

(2) Unique item identifier type.

(3) Issuing agency code (if concatenated unique item identifier is used)

(4) Enterprise identifier (if concatenated unique item identifier is used).

(5) Original part number (if there is serialization within the original part number).

(6) Lot or batch number (if there is serialization within the lot or batch number).

(7) Current part number (optional and only if not the same as the original part number).

(8) Current part number effective date (optional and only if current part number is used).

(9) Serial number (if concatenated unique item identifier is used).

(10) Governments unit acquisition cost.

(11) Unit of measure.

(12) Type designation of the item as specified in the contract schedule, if any.

(13) Whether the item is an item of Special Tooling or Special Test Equipment.

(14) Whether the item is covered by a warranty.

(e) For embedded subassemblies, components, and parts that require DoD item unique identification under paragraph (c)(1)(iii) of this clause or whenitem unique identification is provided under paragraph (c)(1)(v), the Contractor shall report as part of the Material Inspection and Receiving Report specified elsewhere in this contract, the following information:

(1) Unique item identifier of the parent item under paragraph (c)(1) of this clause that contains the embedded subassembly, component, or part.

(2) Unique item identifier of the embedded subassembly, component, or part.

(3) Unique item identifier type.

(4) Issuing agency code (if concatenated unique item identifier is used).

(5) Enterprise identifier (if concatenated unique item identifier is used).

SPRPA1-20-R-W265 PAGE 11 OF 65

ITEM UNIQUE IDENTIFICATION AND VALUATION (MAR 2016)

(6) Original part number (if there is serialization within the original part number).

(7) Lot or batch number (if there is serialization within the lot or batch number).

(8) Current part number (optional and only if not the same as the original part number).

(9) Current part number effective date (optional and only if current part number is used).

(10) Serial number (if concatenated unique item identifier is used).

(11) Description.

Once per item.

(f) The Contractor shall submit the information required by paragraphs (d) and (e) of this clause as follows:

(1) End items shall be reported using the receiving report capability in Wide Area WorkFlow (WAWF) in accordance with the clause at 252.232-7003. If WAWF is not required by this contract, and the contractor is not using WAWF, follow the procedures at http://dodprocurementtoolbox.com/site/uidregistry/.

(2) Embedded items shall be reported by one of the following methods --

(i) Use of the embedded items capability in WAWF;

(ii) Direct data submission to the IUID Registry following the procedures and formats at http://dodprocurementtoolbox.com/site/uidregistry/; or

(iii) Via WAWF as a deliverable attachment for exhibit line item number < > , Unique Item Identifier Report for Embedded Items, Contract Data Requirements List, DD Form 1423.

(g) Subcontracts. If the Contractor acquires by subcontract, any item(s) for which item unique identification is required in accordance with paragraph (c)(1) of this clause, the Contractor shall include this clause, including this paragraph (g), in the applicable subcontract(s), including subcontracts for commercial items.

252.211-7006

PASSIVE RADIO FREQUENCY IDENTIFICATION (DEC 2019)

(a) Definitions. As used in this clause --

"Advance shipment notice" means an electronic notification used to list the contetents of a shipment of goods as well as additional information relating to the shipment, such as passive radio frequency identification (RFID) or item unique identification (IUID) information, order information, product description, physical characteristics, type of packaging, marking, carrier information, and configuration of goods within the transportation equipment.

"Bulk commodities" means the following commodities, when shipped in rail tank cars, tanker trucks, trailers, other bulk wheeled conveyances, or pipelines:

(1) Sand.

(2) Gravel.

(3) Bulk liquids (water, chemicals, or petroleum products.)

(4) Ready-mix concrete or similar construction materials.

(5) Coal or combustibles such as firewood.

(6) Agricultural products such as seeds, grains, or animal feed.

"Case" means either a MIL-STD-129 defined exterior container within a palletized unit load or a MIL-STD-129 defined individual shipping container.

"Electronic Product Code (EPC)" means an identification scheme for universally identifying physical objects via RFID tags and other means. The standardized EPC data consists of an EPC (or EPC identifier) that uniquely identifies an individual object, as well as an optional filter value when judged to be necessary to enable effective and efficient reading of the EPC tags. In addition to this standardized data, certain classes of EPC tags will allow user-defined data. The EPC Tag Data Standards will define the length and position of this data, without defining its content.

"EPCglobal" means a subscriber-driven organization comprised of industry leadersrs and organizations focused on creating global standards for the adoption of passive RFID technology.

"Exterior container" means a MIL-STD-129 defined container, bundle, or assembly that is sufficient by reason of material, design, and construction to protect unit packs and intermediate containers and their contents during shipment and storage. It can be a unit pack or a container with a combination of unit packs or intermediate containers. An exterior container may or may not be used as a shipping container.

"Palletized unit load" means a MIL-STD-129 defined quantity of items, packed or unpacked, arranged on a pallet in a specified manner and secured, strapped, or fastened on the pallet so that the whole palletized load is handled as a single unit. A palletized or skidded load is not considered to be a shipping container. A loaded 463L System pallet is not considered to be a palletized unit load. Refer to the Defense Transportation Regulation, DoD 4500.9-R, Part

SPRPA1-20-R-W265 PAGE 12 OF 65

252.211-7006 (CONT)

PASSIVE RADIO FREQUENCY IDENTIFICATION (DEC 2019)

II, Chapter 203, for marking of 463L System pallets.

"Passive RFID tag" means a tag that reflects energy from the reader/interrogator or that receives and temporarily stores a small amount of energy from the reader/interrogator signal in order to generate the tag response. The only acceptable tags are EPC Class 1 passive RFID tags that meet the EPCglobal Class 1 Generation 2 standard.

"Radio frequency identification (RFID)" means an automatic identification and data capture technology comprising one or more reader/interrogators and one or more radio frequency transponders in which data transfer is achieved by means of suitably modulated inductive or radiating electromagnetic carriers.

"Shipping container" means a MIL-STD-129 defined exterior container that meets carrier regulations and is of sufficient strength, by reason of material, design, and construction, to be shipped safely without further packing (e.g., woodenboxes or crates, fiber and metal drums, and corrugated and solid fiberboard boxes).

(b)(1) Except as provided in paragraph (b)(2) of this clause, the Contractor shall affix passive RFID tags, at the case- and palletized-unit-load packaging levels, for shipments of items that --

(i) Are in any of the following classes of supply, as defined in DoD Manual 4140.01, Volume 6, DoD Supply Chain Materiel Management Procedures: Materiel Returns, Retention, and Disposition:

(A) Subclass of Class I - Packaged operational rations.

(B) Class II - Clothing,…