DMMAVE35-15-PD-13MAY16.pdf

13 May 2016

NRL 5524

PURCHASE DESCRIPTION

MULTIMETER, DIGITAL

Amendment

GMG: DMMAVE35-15

SCAT: 4245 / TAMCN: H7030

Solicitation No: SPRMM116RYK34

1.0 GENERAL This procurement requires a hand-held 3-1/2 digit digital multimeter.

2.0 CLASSIFICATION The multimeter shall meet the requirements of MIL-PRF-28800F

Class 3 for Navy shipboard, submarine, shore and Marine Corps applications.

3.0 OPERATIONAL REQUIREMENTS The specifications provided below are the minimum requirements and accuracies that will meet the Government's need. The multimeter shall at least meet these requirements and accuracies and may provide better performance. The multimeter shall be provided with auto-ranging capabilities and a memory function, which captures and holds a reading for display.

3.1 DC Voltage

3.1.1 Range: 1 mV to 1 kV

3.1.2 Accuracy: ±(0.3% of reading + 1 digit)

3.2 AC Voltage (The meter shall be average responding and RMS indicating)

3.2.1 Range: 1 mV to 1 kV

3.2.2 Frequency range: 45 Hz to 500 Hz: 1 mV to 3.2 V; 45 Hz to 1 kHz: 3.2 V to 1 kV

3.2.3 Accuracy: ±(2% of reading + 2 digits)

3.2.4 Input RC: 10 MOhm or greater shunted by 100 pF or less

3.3 DC Current

3.3.1 Range: 10 µA to 10 A

3.3.2 Accuracy: ±(1.5% of reading + 2 digits)

3.4 AC Current

3.4.1 Range: 10 µA to 10 A from 45 Hz to 1 kHz

3.4.2 Accuracy: ±(2.5% of reading + 2 digits)

3.5 Resistance

3.5.1 Range: 0.1 Ohm to 50 MOhm

3.5.2 Accuracy: ±(0.5% of reading + 2 digits) up to 600 Ohm, ±(0.5% of reading + 1digit) up to 3.2 MOhm, ±(2% of reading + 1 digit) 3.2 MOhm to 50 MOhm

3.6 Continuity and Diode Tests The meter shall be provided with the capabilities for continuity and diode tests. An audible signal shall be activated to indicate continuity.

An audible or visual signal shall be provided to indicate a good/bad diode.

3.7 Overload Protection

3.7.1 Voltage protection: The meter shall be rated as 600V CAT IV and 1000V CAT III device per IEC-1010-1 2nd ed. Agency approvals shall include either UL 61010 or CSA C22.2 No 1010-1-92.

3.7.2 Current protection: Both the mA and Amp current input jacks should be protected by fuses which are rated to withstand the maximum current input for the appropriate input jack.

3.7.3 Resistance protection: 1000 Vdc or AC

3.8 Display A 3-1/2 digit LCD display according to MIL-PRF-28800F shall be provided. A bar graph or analog indicator shall be provided for peak or null interpretation.

3.8.1 Backlight: A backlight shall be provided.

3.9 Damage Protection The meter shall have an elastomeric case to absorb mechanical impacts in field operation.

4.0 GENERAL REQUIREMENTS

4.1 Temperature

4.1.1 Operating temperature: -10°C to +50°C

4.1.2 Non-operating temperature: -40°C to +60°C

4.2 Power Source

4.2.1 Internal DC battery: Internal power source requirements according to MIL-PRF-

28800F are invoked. The batteries shall be a commercially available type and have a life span of at least 400 hours.

4.3 Weight 0.55kg maximum

4.4 Size 20cm H, 10cm W, 6cm D, nominal

4.5 Accessories The equipment shall be provided with safety-designed test leads in accordance with MIL-PRF-28800F.

4.6 Wireless Connectivity Any capability of the equipment to communicate wirelessly, including but not limited to Wi-Fi and Bluetooth, shall be disabled.

4.7 Battery Restrictions Per MIL-PRF-28800F, Lithium and Mercury batteries are prohibited without prior authorization. A request for approval for the use of Lithium and Mercury batteries shall be submitted with production lot delivery, after contract award. Approval shall apply only to the specific model proposed.

Exceptions: Per Naval Ordnance Safety and Security Activity (NOSSA), the use of Lithium primary (non-rechargeable) coin cell batteries meeting the following criteria is authorized for Naval personnel and on Naval activities, surface ships, submarines, and aircrafts:

- Commercially available coin cell batteries, unmodified, and used in the device recommended by the application manufacturer.

- Coin cell batteries shall only be used in single cell configurations.

- Coin cell batteries shall not be rated for more than 3 volts (maximum nominal output voltage).

- Coin cell batteries shall not be rated for more than 1 Ampere-Hour nameplate capacity.

The coin cell manufacturer and model identification/part number shall be provided at the time of submission of proposals.

4.8 Calibration Interval The calibration interval shall be 24 months minimum. At the end of this interval a minimum of 85% of the unit shall remain in tolerance.

4.9 Calibration Procedure The procedure, software, and special interfaces/adapters that are needed for the equipment calibration shall be provided.

4.10 Transit Case The equipment shall be provided with a protective soft transit case.

The transit case shall have provisions for stowage of the equipment, accessories, and operator’s manual.

4.11 Technical Manual The maintenance philosophy for this unit shall be level 1 (per MIL-

PRF-28800F) and require operational verification of the unit. The technical manual shall conform to the level 1 maintenance philosophy. A Use and Installation manual (Operator’s Manual) shall be provided. Maintenance and servicing instructions (Service Manual) shall be to the unit operational verification level. Operator’s and Service Manual may be combined in a single manual. Information required for performance verification shall include:

• Instructions to verify equipment performance,

• List the equipment required for verification tests,

• Simple troubleshooting and maintenance only,

• Step-by-step instructions for test connections,

• Acceptable result criteria,

• Calibration information, and, if applicable,

• Self-test routines.

The technical manual shall be provided in both printed and electronic formats. The printed format shall be otherwise normally provided. The electronic format shall be in Portable Document Format (PDF) - ISO 32000-1:2008. A single CD/DVD containing the Operator’s and Service Manuals is required.

The statement of copyright release:

“REPRODUCTION AND DISTRIBUTION OF THIS TECHNICAL MANUAL IS

AUTHORIZED FOR U.S. GOVERNMENT PURPOSES.”

shall be printed in the first two pages of each technical manual and on the surface of the CD/DVD supplied.

4.12 Training Materials Training materials that demonstrate the features, detailed operations and procedures with step-by-step instructions for using the equipment shall be provided. The training material shall be delivered in technical manual or interactive CD-ROM formats.

4.13 Additional Requirements

4.13.1 Human Readable Identification Labeling:

4.13.1.1 Equipment: Per MIL-PRF-28800F, a human readable label shall be provided for all production lot units conforming with MIL-STD-130N and permanently affixed on the equipment in an easily readable location. Required fields on the label are; CAGE, part number, and serial number. Size of the label shall conform to the size of the equipment.

4.13.1.2 Case: Soft carrying case shall be provided for the unit and accessories.

4.13.2 Shipping container: For production lot units the package or carton containing the equipment for shipment shall be marked per MIL-STD-129P.

4.13.3 Other Additional Requirements: Shall be specified in the CDRL of the solicitation.