CDRL.pdf

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

Form Approved 0MB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarSing this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports 0701-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of am no oerson shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid 0MB control number. Please DO NOT RE1URN your form to the above address. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No.

listed in Block E.

A. CONTRACT LINE ITEM NO. B. EXHIBIT

A

C. CATEGORY: NDTI

TOP TM OTHER

D. SYSTEM/ITEM (OMAN) (GUB-18-073)

PARTS KIT, FUSELAGE

E. CONTRACT/PR NO.

FD2020-18-01783

F. CONTRACTOR

1. DATA ITEM NO.

A00 1

2. TITLE OF DATA ITEM

Test/Inspection Report

3. SUBTITLE

4. AUTHORITY (Data Acquisition Document No.)

DI-NDTI-80809B/T

5. CONTRACT REFERENCE

CLIN for Data

6. REQUIRING OFFICE

416 SCMS/GUEAA

7. DO 250 REQ

DD

9. 01ST STATEMENT

REQUIRED

r.

I 10. FREQUENCY

OTIME

12. DATE OF FIRST SUBMISSION

SEE BLK 16

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

8. APP CODE

A riAS OF DATE

SEE BLK 16

13. DATE OF SUBSEQUENT

SUBMISSION

SEE BLK 16

Draft

Final

Ileg Repro

16. REMARKS

NOTE: Changes to office symbols and/or e-mail addresses, when necessary shall be made by letter through the CO/ACO without further revision to this CDRL.

1. BLK 4: Contractors format is acceptable. Paragraph 10.2 of DI-NDTI-80809B is clarified as follows:

a. All dimensions and tolerances specified on the manufacturing data shall be listed in one column, with the actual corresponding reading obtained from the inspection of the part listed in another column. .

b. Materials utilized in the manufacture of 'First Article" item shall be identified and certified along with a copy of material purchase requests as conforming to applicable data requirements.

c. Material processing, including finish requirements (plating, heat treatment, welding, inspecting, anodize, painting, etc.) utilized in the manufacture of "First Article" item shall be identified and certified as conforming to applicable requirements. A copy of the purchase order certifiing the process accomplished at other than contractor facility shall be included.

d. Other requirements as called out on Engineering Data Requirement (OO-ALC Form 462).

2. The Distribution Statement, Export Control Warning and Destruction Notice shall be placed on the first sheet of each document and located in a conspicuous location.

BLK 9: DISTRIBUTION STATEMENT "B" Distribution authorized to U.S.

Government agencies only. (Test & Evaluation) (20 September 2018). Other requests for this document shall be referred to (416 SCMS/GUEAA, Hill AFB, UT 84056-5826).

EXPORT CONTROL WARNiNG: All technical documents/data (printed, digital/electronic) that are determined to contain export-controlled technical data, shall be marked with the following statement:

EXPORT CONTROL WARNiNG: This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.) or the Export Administration Act of 1979 (Title 50, U.S.C., App. 2401 et seq.), as amended. Violations of these export laws are subject to severe criminal penalties. Disseminate lAW provisions of DoD Directive 5230.25.

416 SCMS/ 1

GUEAA

6071 Gum LN Bldg. 1223

Hill AFB, UT 84056-5826

SEE BLK 16

15.TOTAL 0

G. PREPARED BY '/ Q

Nila Dagsen (Contractor Data ana er

H. DATE

20 Sep 2018

I. APPROVED BY

William Garcia (Engineer)

J.DATE

20 Sep 2018

17. PRICE GROUP

18. ESTIMATED

TOTAL PRICE

DD FORM 1423-1, FEB 2001 PREVIOUS EDITION MAY BE USED. Page 1 of 2 PageS

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

A. CONTRACT UNE ITEM NO. B. EXHIBIT C. CATEGORY:

A TOP TM OTHER NDTI

D. SYSTEM/ITEM (OMAN) (GUB-18-073) E. CONTRACT/PR NO. F. CONTRACTOR

PARTS KIT, FUSELAGE FD2020- 18-01783

16. REMARKS (Continued)

DESTRUCTION NOTICE: For classified documents, follow the procedures in DoD 5220.22-M, National Industrial Security Program Operating Manual (NISPOM), Section 5-705, or DoD 5200.1-R, Information Security Program Chapter VI. For unclassified, limited documents, destroy by any method that will prevent disclosure of contents or reconstruction of the document.

3. BLKs 10, 11, 12, 13, 14:

a. For Contractor Testing - submit JAW the current delivery schedule.

b. For Government Testing - Report to assist in "First Article" testing by the Air Force shall be submitted concurrently with the "First Article" item either in the packaging of the shipping container or separately if the report whl not fit within the container packaging unfolded. When shipped in the "First Article" container, the report shall be enclosed in a paper or plastic envelope.

c. SHIP TO: Non-Accountable Bay Transportation Officer Building 849 West Hill AFB, UT 84056-5999

MARK FOR: 809 MXSS/MXDEB

7278 4th Street (Bldg. 100, Bay D) Hill AFB, UT 84056-5205

NOTE: If report is shipped separate from "First Article" item, send report to "MARK FOR" address listed above.

d. Contractor shall deliver the Test/Inspection Report via e-mail to the following e-mail address: william.garciaus.af.mil

DD FORM 1423-1, FEB2001 Page 2 of 2 Pages