Spec_Packaging_instructions_P71021_1revA.pdf

SPECIAL PACKAGING INSTRUCTION (SPI)

DOD SPI INDEX NUMBER

NOMENCLATURE

SPI NUMBER

QUPUI

EA 1

P71021_1

DRAWING/PART NO.

UNIT PACK AND MILITARY PRESERVATION REQUIREMENTS

NATIONAL STOCK NUMBER

AP15290599

71021MASK CARRIER

8465---01---529---0599

ITEM WEIGHT---

APPROVAL REVISION DATE

0.40 lbs.

21 SEPT 2010PAGE NUMBER NUMBEROF PAGES

275---0024---003 ---

DISTRIBUTION STATEMENT A: Approved for public release

KJR

STEPS SPECIFICATION STYLE TYPE GRADE CLASS SIZE AND REMARKS (INCHES)

UNIT PACK LOGISTICS DATA (Approximate unit pack weight and size)

WEIGHT (POUNDS) CUBE (CUBIC FEET)

INTERMEDIATE PACKAGING

MARKING

REMARKS

(B)(C) 1 Heat Seal or TapeClosure (C)(D) 2

QUALITY PERFORMANCE & TESTING REQUIREMENTS

MIL---DTL---117

IAWMIL---STD---2073---1

As specified hereon.

IAWMIL---STD---129

As specified hereon.

IAWMIL---STD---2073---1

As specified hereon. SEE NOTE (G)

0.41 lbs.

X ( )

( )X

( )X

X

0.303 cu. ft.

SIZE (EXTERIOR INCHES)

20.80 x 16.80 x 1.50

UNIT PACKMATERIALS

Clean and dry using any applicable method that is not injurious to the item

Container (Bag)

Methods of Preservation (MOP) --- 10

2 III B 20 x 16

LEVEL OF PACK (EXTERIOR PACKAGING)

IAWMIL---STD---2073---1 & Contract As specified hereon.( ) SEE NOTE (E)X

( )X

The current revision to each of the specifications, standards, and drawings listed on this SPI in effect on the date of invitation for bid constitute a mandatory part of this Instruction. Unless otherwise specified, materials will be minimum size IAWMIL---STD---2073---1 or material specifications. Tolerances shall be IAWmaterial specifications.

(A) --- This SPI is not applicable for Interplant shipments. Packaging andmarking for interplant shipments are for supplies and materials that do not directly enter the military supply system. Typical interplant shipments are shipments from a vendor to a subcontractor or a prime contractor, or between contractors and subcontractors, or from a vendor or contractor to a military arsenal, plant, or other activity for evaluation, immediate use, or further processing as specified in the applicable contract.

(B) --- Bag material shall conform to A---A---3174 and have a minimum thickness of 4 mils. A commercially equivalent bag with a minimum thickness of 4 mils is acceptable.

(C) --- Place Mask Carrier into the specified container (step 1) and close (step 2).

ITEM SIZE ---

ITEM SI

275---0065---001 A 1 APR 2015

Original Preparer:

KJM

Revised by:

11 1/2 x 11 1/2 x

ITEM SIZE ---

ITEM CODE ---

ITEM DATA

R. Hazleton DAAD13---00C---0021 Karyn Merson

1 1/2 inches

(APPROX)

Date: 11 MAR 2015

ITEM CODE ---

Date: 18 AUG 2004

ECBC 81361

NOMENCLATURE

SPI NUMBER

P71021_1

PAGE NUMBER

DRAWING/PART NO.

NATIONAL STOCK NUMBER

AP15290599

71021MASK CARRIER

8465---01---529---0599

(D)--- Closure shall be accomplished by heat sealing or taping as follows: Heat sealed closures (step 2) shall be accomplished in accordance with the barrier bag or barrier material supplier’s recommendations for dwell, pressure and temperature requirements. The volume of trapped air within the bag (step 1) shall be kept to a minimum by compressing the bag around the contents, or carefully drawing a vacuum inside the bag, prior to final heat sealing. Caution shall be taken to prevent damage to the item or rupture of bag. Taped closures shall be accomplished by folding the excess material at the opening of the bag over onto the body of the bag and secure with tape conforming to ASTMD5486, Type I, Class 2, Size As Required. For taped closures, the volume of trapped air within the bag (step

1) shall be kept to a minimum by compressing the bag around the contents.

(E) - Packing. Level of pack shall be as specified in the contract or order.

(F) --- Palletization andUnitization. The shipping container, whennot requiring skids, shall beplacedon the pallet IAWMIL---STD---147 and ANSI MH1 when:

---Shipments of identical items packed in shipping container(s) exceed the total of 50 cubic feet per destination and do not exceed the size or weight limitations for palletized loads.

---The total number of containers, not having identical items going to the samedestination, weighs250 pounds or greater (excluding pallet), or has a volume of 20 cubic feet or greater and does not exceed the size or weight limitations for palletized loads.

(G) --- PACKAGING QUALITY ASSURANCE PROVISIONS

This section outlines the requirements for conducting appropriate quality conformance inspections, examinations, tests and acceptance for packaging and shall be required as specified in the contract.

1. Classification of inspections. The inspection requirements for the packaged item described herein are conducted during First Article Testing and Production Lot Testing (Conformance).

2. First Article Testing. The first article inspection and approval (if FAT is required by the contract) consists of the contractor inspection of items prior to regular production. The first article testing shall be conducted as follows:

a. Sampling. The first article packaging sample shall consist of not less than three unit pack containers and their contents, and when heat seal seam testing is required, three empty barrier bags.

Also, if applicable, packaged samples shall be taken from the quantity of first article sample items specified. Packaged samples shall be produced using the samemethods, materials and equipment as will be used during regular production.

b. Visual Examination and Tests. Shall be as specified in MIL---STD---2073---1, Appendix G, and:

(1). Packaged samples shall be examined IAW the preservation examinations to determine compliance IAW Table G---I of MIL---STD---2073---1.

NOMENCLATURE

SPI NUMBER

P71021_1

PAGE NUMBER

DRAWING/PART NO.

NATIONAL STOCK NUMBER

AP15290599

71021MASK CARRIER

8465---01---529---0599

(2). Leakage and heat seal seam tests are required for sealed containers as specified in Table G---II of MIL---STD---2073---1. Note: Method of Preservation 10 does NOT require tests.

(3). Compliant wood requirements shall be IAW the contract. Examination shall include review and acceptance of wood packaging material, containers, pallets and dunnage.

(4). The level of pack shall be as specified in the contract. The exterior shipping configuration shall include examination to verify compliance with MIL---STD---2073---1 guidelines for intermediate and shipping containers for the level of pack specified.

(5). Packaged samples shall be marked IAWMIL---STD---129.

c. Certificate of Compliance. Certification shall be required for ALL packaging materials, containers, palletization materials, and marking specified in this SPI. Format shall be IAW the contract and shall include, at a minimum, the contractor’s name, address, phone number), contract number, item name, part number and/or national stock number, a statement specifying what it complies with (i.e. material, size, specification, standard), dated, printed name and title of certifying official, and shall be signed.

d. Acceptance criteria. Samples that fail to comply with any of the applicable requirements shall be rejected.

3. Production Lot Testing (Conformance).

a. Sampling. Sampling size shall be IAW the Attributes Sampling Plan Table of MIL---STD---1916 for visual examination. Verification Level I shall be used. If required, three samples from the sampling size shall be selected for destructive testing (leakage and heat seal seam tests). Existing sampling plans in item specifications or quality assurance provisions shall take precedence.

b. Visual Examinations and Tests. Shall be conducted IAW 2.b above. If applicable, destructive testing will be conducted after visual examination.

c. Certificate of Compliance. Shall be prepared IAW 2.c above.