Exhibit A -Technical Requirements Document.pdf

Exhibit A SPRBL1-20-Q-0011 Page 1 of 7 Issue: 03 June 2019

TECHNICAL REQUIREMENTS DOCUMENT

Power Supply

NSN 6130-01-565-4895, P/N NG2602-T

Exhibit A SPRBL1-20-Q-0011 Page 2 of 7

TABLE OF CONTENTS

APPLICABLE DOCUMENTS

CONFIGURATION BASELINE

CHEMICAL AGENT RESISTANT COATING (CARC)

Paint Colors

Special Instructions

PACKAGING

Wood Packing Material

Military Packaging

CONTRACT DATA REQUIREMENT LIST (CDRL) DD 1423-1

CDRL List

Individual CDRLs

Exhibit A SPRBL1-20-Q-0011 Page 3 of 7

APPLICABLE DOCUMENTS

Military and Federal Standards MIL-STD-130N Identification Marking of U.S. Military Property

Military and Federal Specifications

Other Documents

DI-MISC-80711A Scientific and Technical Reports

Commercial Documents ASTM D3951-15 Standard Practice for Commercial Packaging.

Security Documents

CONFIGURATION BASELINE

The NG2602 power supply is used in the AN/TSQ-232 family of Command Post Platforms (CPPs). AN/TSQ- 232 CPPs are mobile command posts, which contain various configurations of communications equipment.

Critical pieces of CPP communications equipment run on 28 Volt Direct Current (VDC) power; however, primary external power for the CPP is supplied as 208 Volt Alternating Current (VAC). The NG2602 Power Supply converts externally supplied 208 VAC into usable 28 VDC for the internal communications equipment. Proper function of the NG2602 power supply is therefore critical to effective operation of the AN/TSQ-232 family of Command Post Platforms.

The applicable Configuration Baselines (CB), for the listed Configuration Item (CI) and/or Computer Software Configuration Item (CSCI), are as listed in the table below.

NSN Nomenclature Part Numbers/Drawings 6130-01-565-4895 Power Supply NG2602

Exhibit A SPRBL1-20-Q-0011 Page 4 of 7

CHEMICAL AGENT RESISTANT COATING (CARC)

Stencil “CARC” in CARC paint in close proximity to the nameplate using a contrasting color, or use plates or embossed lettering. Marking shall be durable enough to withstand all environmental conditions during field use.

Paint Colors

Applicable Location Color

Color No.

FED-STD 595

X Exterior Tan 686A 33446

Special Instructions:

IUID Marking

New items: The contractor shall provide IUID, or DoD recognized equivalent, for all items delivered with an acquisition cost of $5000 or more. For long term contracts, any items that have range quantity prices established, that will exceed the $5000 unit price shall have IUID markings from the beginning of the contract.

IUID markings shall be IAW MIL-STD-130N.

Commercial Markings. All other items shall have acceptable commercial markings that meet the guidelines in Department of Defense (DoD) Guide to Uniquely Identifying Items http://www.acq.osd.mil/dpap/pdi/uid/index.html.

Permanency and Legibility. The IUID marking and identification plates, tags, etching, or labels when used on equipment, parts, assemblies, subassemblies, units, sets, groups, or kits shall be as permanent as the normal life expectancy of the item and be capable of withstanding the environment, test, cleaning, repair, and rebuild procedures specified for the item. Legibility shall be as required and verified for ready readability per MIL-

STD-130N

Deleterious Effect. Marking of items shall be accomplished in a manner that will not adversely affect the life and utility of the item. Marking materials creating hazardous conditions shall not be used. Placement and choice of the marking shall not create hazardous conditions.

IUID Coding. IUID markings and readability requirements shall comply with MIL-STD-130N.

Symbology markings and the order of priority for marking the hardware shall be in accordance with MIL-STD 130N. First priority is the 2D data matrix symbol (machine readable) IUID is the minimum requirement when http://www.acq.osd.mil/dpap/pdi/uid/index.html

Exhibit A SPRBL1-20-Q-0011 Page 5 of 7 there are severe space limitations. The second priority is the human readable characters. The third priority is the Linear Bar Code.

If the technical data has not specified the marking location, markings shall be located such that they are visible during item use, provided that sufficient space is available, and does not interfere with equipment operations.

If items are not described by Government Product Technical Data (i.e. Commercial Items), the contractor shall submit diagrams showing placement and description of the IUID marking and applicable installation and processing instructions for government review and approval IAW with CDRL A001 for DI-MISC-80711A and this TRD.

Per the Department of Defense, Item Unique Identification of Government Property Guidebook, Reporting Government Property In the Possession of the Contractor (PIPC), Guidance for: Defense Federal Acquisition Regulation (DFARS) 252.211-7007, Item Unique Identification of Government Property, Version 1.0, September 21, 2007

For new contracts issued after September 13, 2007, DoD will include an Interim Rule, DFARS 252.211-7007, Item Unique Identification of Government Property (DFARS Case 2005-D015), which permanently revises requirements for reporting of PIPC. The interim rule permanently replaces the DD Form 1662 reporting requirements with requirements for DoD contractors to electronically submit, to the IUID registry, the IUID data applicable to PIPC.

It should be understood that in accordance with DFARS 211.274-5, Contract clauses, the clause at DFARS 252.211-7003, Item Identification and Valuation, must be included in any contract that incorporates the clause at DFARS 252.211-7007, Item Unique Identification of Government Property. This is essential to assure there is no ambiguity in the requirements for assigning, registering, reporting and marking PIPC.

The contractor shall maintain an accurate, current list of IUIDs for all manufactured items on this contract.

Dates of manufacture, substitutions, shop changes, etc. shall be included on this list. The list shall be available for inspection by the PCO or other Government representative at any time during the life of this contract. The contractor shall provide this list to the government at the end of the contract.

Pricing of IUID Requirements. All efforts required by this SOW and contract, including, but not limited to, the preparation of ECPs or notification of marking deficiencies, PIPC reporting, serial number data reporting at end of contract and the actual marking of hardware, will be included in the base contract pricePACKAGING

Wood Packing Material Wood packing material includes pallets. See DLAD 52.247-9012 Requirements for Treatment of Wood Packaging Material (WPM).

Military Packaging DS7029 and/or DS7033 Preservation, Packing and Marking Instructions

Exhibit A SPRBL1-20-Q-0011 Page 6 of 7

DS7029 - DS7033 LEGEND

Qty Quantity Prot Req Protection Required PKG-REF Packaging Reference (Military/Federal Specification or Standard) SPI Special Packaging Instruction LPK Level of Packing QUP Quantity per Unit Pack ICQ Intermediate Container Quantity Pkg Reqmt Codes Packaging Requirement Codes when PKG-REF cites MIL-STD-2073 The below codes are for special markings:

PC Project Code WG Warranty/Guarantee SL Shelf Life BC Bar Code FMS Foreign Military Sales

DS7029 - DS7033

NSN Prot Req PKG-REF or SPI LPK QUP ICQ Special Markings

Pkg J. J J J J J J J J J

Reqmt I. II. III. IV. V. VI. VII.

V

II

.a IX X

Codes

(MP

) (CD)

(PM

(WM

) (CD) (CT) (UC)

(I C

(P

K) (SM)

6130-01-565-4895 Military ASTM D3951-15 B 001 - n/a n/a n/a n/a n/a n/a n/a n/ a n/a n/a BC

CONTRACT DATA REQUIREMENT LIST (CDRL) DD 1423-1

CDRL List

CDRL

Data Line No. DID Identification Title

A001 DI-MISC- 80711A Scientific and Technical Reports – IUID Markings & Inst.

Exhibit A SPRBL1-20-Q-0011 Page 7 of 7

Individual CDRLs

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item) Form Approved OMB No. 0704-0188

Public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA. 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project (0704-0188), Washington, DC 20503. Please DO NOT RETURN your form to either of these addresses. Send completed form to the Government Issuing Contracting Officer for Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO. B. EXHIBIT C. CATEGORY:

TDP TM OTHER MISC

D. SYSTEM/ITEM F. CONTRACTOR

NG2602 Power Supply

E. CONTRACT/PR NO.

SPRBL120Q0011

1. DATA ITEM NO. 2. TITLE OF DATA ITEM

A001 Scientific and Technical Reports IUID Marking Diagram/Instructions

4. AUTHORITY (Data Acquisition Document No.) 5. CONTRACT REFERENCE 6. REQUIRING OFFICE

DI-MISC-80711A FCDD-ISP-TR

7. DD 250 REQ 9.DIST STATEMENT

REQUIRED

10. FREQUENCY 12. DATE OF FIRST

SUBMISSION 14. DISTRIBUTION

LT ASREQ 120DAC b. COPIES

8. APP CODE N/A 11. AS OF DATE 13. DATE OF SUBSEQUENT

SUBMISSION

a. ADDRESSEE Draft

Final

N/A SEE ITEM 16 Reg Repro

16. REMARKS:

BLK 4: Delete block 10.2 of Data Item Description (DID) and prepare in accordance with CDRL and the statement of work..

BLK 12: The Government has 30 days to review and comment.

BLK 13: Delivery of final shall be 30 days after receipt of Government comments. Government has 60 days to determine acceptance. Contractor to submit DD250 IAW WAWF of UID Marking Diagram/Instructions

Block 14 All digital files will be provided both by electronic submission, e.g., e-mail, FTP, etc., as arranged with the requiring office, and also by CD ROM, readable by computers running Microsoft Windows

FCDD-ISP-TR 1 1 0

15. TOTAL 1 1 0

G. PREPARED BY H. DATE I. APPROVED BY J. DATE

Brian Bomar

FCDD-ISP-TR

05/31/2019 Daniel Webster

FCDD-ISP-TR