COUPLING_SLEEVE_drawing.pdf

SLEEVE

REFERENCES

NO TITLE DWG NUMBER

1 TAPER GAGES, CPLG NAVSEA 243‐6985878

HOLE TOLERANCES – APPLY TO ALL ROUND

HOLES WITHIN NOMINAL SIZE RANGE

COVERED UNLESS OTHERWISE SPECIFIED

HOLE DIAMETER TOLERANCE

0.0135 TO 0.125 +.005 ‐ ‐.001

0.126 TO 0.250 +.006 ‐ ‐.001

0.251 TO 0.500 +.008 ‐ ‐.002

0.501 TO 0.750 +.009 ‐ ‐.002

0.751 TO 1.000 +.010 ‐ ‐.003

1.001 TO 2.000 +.012 ‐ ‐.004

2.001 TO 3.000 +.015 ‐ ‐.005

FABRICATION TOLERANCES

(UNLESS OTHERWISE SPECIFIED)

DIMENSION TOLERANCE

1PL 2PL 3PL

ABV 0.00 TO 6.00 ± .1 ± .02 ± .005

ABV 6.00 TO 18.00 ± .1 ± .04 ± .010

ABV 18.00 TO 36.00 ± .1 ± .06 ± .015

ABV 36.00 ± .1 ± .08 ± .020

FILLETS & RADII TO BE 0.06 TO 0.14

SURFACE TEXURE SYMBOLS: ANSI Y14.36‐1978

THREADS TO BE IN ACCORDANCE WITH FED‐STD‐H28

ANGULAR: ± .5⁰

PARTS LIST

PART NUMBER PART NAME DESCRIPTION; CAGE/SPECIFICATION

1 SLEEVE NIMOSTL; MIL‐S‐23284 CL‐1

2 SPLIT COLLAR N/A

Note: Sleeve (PN 1) is not a LEVEL I material.

NOTES

1 THE INSIDE DIAMETER TAPER OF THE SLEEVE SHALL BE MACHINED TO GAGES,

REFERENCE 1. THE PLUG GAGE SHALL FIT THE SLEEVE, PN 1, WITH A UNIFORMLY

DISTRIBUTED CONTACT OF AT LEAST 80 PERCENT. SLEEVE, PN 1, SHALL BE MACHINED

TO GAGES, REFERENCE 1.

2 BOLT HOLES IN THE SLEEVE PN 1 SHALL BE IDENTIFIED BY DIE STAMPING NUMERALS ON

THE OUTSIDE DIAMETER OF THE SLEEVE. THE HOLES SHALL BE NUMBERED

CONSECUTIVELY IN A CLOCKWISE DIRECTION LOOKING FORWARD WITH BOLT HOLE

NUMBER 1 LOCATED AS SHOWN.

3 KEYWAYS SHALL BE FINISHED TO 63 MICRO‐INCHES (RMS) AND POLISHED TO REMOVE

SHARP EDGES, BURRS, AND TOOL MARKS.

4 SURFACE FINISHES INDICATED BY THE SYMBOL SHALL BE IN ACCORDANCE WITH

ANSI 846.1

5 MACHINING ‐ UNLESS OTHERWISE SPECIFIED:

a. FINISH 125 RMS

b. BREAK SHARP EDGES 0.015 MAX

c. INSIDE CORNERS R 0.010 MAX

d. SHARP FILLETS R 0.010 MAX

6 ACCEPTABLE PERMANENT METHODS OF MARKING IN ACCORDANCE WITH MIL‐STD‐792

a. DIE STAMPING (ALLOWED WITH ROUND BOTTOM, LOW STRESS TYPE DIES). DEPTH

OF IMPRESSIONS 0.010 MAXIMUM

7 SLEEVE SHALL BE ULTRASONICALLY INSPECTED IN ACCORDANCE WITH THE APPLICABLE

MATERIAL SPECIFICATION. ACCEPTANCE CRITERIA SHALL BE IN ACCORDANCE WITH THE

APPLICABLE MATERIAL SPECIFICATION OR VENDOR DRAWING. ACCEPTED PARTS SHALL

BE LEGIBLY AND PERMANENTLY MARKED “UT” IN THE AREA INDICATED.

8 SLEEVE SHALL BE MAGNETIC PARTICLE INSPECTED (MT) IN ACCORDANCE WITH THE

APPLICABLE MATERIAL SPECIFICATION. ACCEPTANCE CRITERIA SHALL BE IN

ACCORDANCE WITH THE APPLICABLE MATERIAL SPECIFICATION OR VENDOR DRAWING.

MAGNETIC PARTICLE TESTING SHALL BE ACCOMPLISHED AFTER FINAL MACHINING

PRIOR TO ASSEMBLY OR WELD CLADDING. ACCEPTED PARTS SHAL LBE LEGIBLY AND

PERMANENTLY MARKED “MT” IN THE AREA INDICATED.

9 ALL DIMENSIONS SHALL BE MEASURED AT 68 DEGREES FARENHEIT OR CORRECTED TO

68 DEGREES FARENHEIT

10 REFERENCE DIMENSIONS ARE SHOWN IN PARENTHESIS AND PROVIDE INFORMATION

BUT ARE NOT NECESSARY FOR PROPER FABRICATION AND INSTALLATION. THESE

DIMENSIONS WILL HAVE NO TOLERANCE AND ARE NOT SUBJECT TO INSPECTION AND

CERTIFICATION.

11 AFTER FABRICATION OF THE SLEEVE, EXACT LOCATION DIMENSIONS OF THE HOLES,

DEPICTED IN SECTION 1‐B, WILL BE PROVIDED.

5.8

7.38

1.2

Ø.750-10UNC-2B ∅.030 M X Y ZMM

SECTION 1-B

4 PLACES

Ø0.765

Ø1.25

PN 1

PN 2

SEE NOTE 11