SALIENT CHARACTERISTICS.pdf

ITEM DESCRIPTION: ASW/PETROLEUM/OILY WASTE WATER HOSE ASSEMBLY

(1-1/2” ID X 25’ LONG)

Or-Equal Purchase Specification:

Hose, Nonmetallic, Nitrile Tube & Nitrile or Neoprene Cover: Coupled and Fully Assembled.

Application for Intended Use: May be used for Temporary Service Petroleum/Oily Waste Transfer Systems, or Shipboard Seawater / Fresh Water Suction/Discharge Services.

Description:

1. Size: 1-1/2” I.D. by 25’ long.

2. Nominal OD: 2”

3. Vacuum: Full

4. Working Pressure: 250 PSI, minimum.

5. Burst Pressure: 1,000 PSI, minimum.

6. Rated bend radius: 6 inches or less.

7. Rated Continuous Temperature: -20ºF to 180ºF

Construction:

8. Tube: Extruded specially compounded Nitrile synthetic rubber. Must meet Rubber Manufacturers Association (RMA) Class A standard for high oil resistance. Hose shall be wrapped or mandrel type construction with a heavy enough wall construction to allow the use of crimped or swaged couplings with interlocking ferrules.

9. Reinforcement: Multiple braids of textile fabrics with a high-tensile wire helix.

10. Cover: Specially compounded Nitrile, Neoprene or blended synthetic rubber. The cover shall be smooth slick finish, not a cloth wrap impression type and shall meet RMA Class B standards for weather, ozone and limited oil resistance.

11. Cover Color: Black cover with a contrasting colored brand strip down the entire lay line with contrasting lettering.

12. Hose end assembly shall be accomplished in accordance with established National Association for Hose Accessories Distribution

(NAHAD) certification standards.

13. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End; Brass, 1-1/2” Cam & Groove Quick Disconnect Adapter by Hose Shank, PT Coupling Co., Part # 15E, Item # 1200515.

b. 2nd Hose End; Brass, 1-1/2” Female Cam & Groove Quick Disconnect Coupler by Hose Shank, with Stainless Steel Cam Arms, Pins, Pull Rings and Passive Locking Device, PT Coupling Co. , Part # 15CSLII, Item # 1290315L2.

c. End fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co. “Pro-Grip C50SS Crimp Ferrule

Stainless Steel” sized to match the hose and fittings. No hose clamps or bands will be accepted.

14. All end fittings must be meet Commercial Item Description (CID) A-A-59326 and shall have a working pressure of 250 PSI or greater. Any manufacturers hose end coupling offered other than the above referenced part numbers must be approved by PSNS Code 260.41.

15. Branding / Marking: Hose shall be continuously ink-branded, stencil painted, Mylar or stripe branded /marked in ½” lettering (minimum), which must be in a contrasting color to the black outer cover of the hose. The lettering shall state as a minimum:

a. Standard Hose Brand/Line/Model number, Petroleum type, Date of Manufacture etc.

b. PSNS & IMF S/99

16. Price quotes for market survey request will not be accepted without the hose, fitting, and ferrule manufacturer cut sheets or product description sheets attached, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone/fax number and manufacturer point of contact. The market survey price quote must reference the manufacturer’s part numbers for the item quoted.

17. All quoting vendors if requested must submit a five-foot long hose assembly at vendor expense, for destructive testing analysis.

18. All Or-Equal offers must be approved by PSNS & IMF Code 260.41 prior to purchase.

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean water as a test medium, at 275 (+10,-0) PSIG for 10 minutes.

Each hose is to be certified to the requirements of the United States Coast Guard (USCG) for the transfer of oil over water. Each certified hose is to be assigned by the manufacturer a unique serial number, to be permanently stamped or etch marked on the hose ferrule of each hose end.

Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards, also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested & USCG certified (100% of hoses) shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date and must correspond to each unique hose serial number.

(1-1/2” ID X 50’ LONG)

Or-Equal Purchase Specification:

Hose, Nonmetallic, Nitrile Tube & Nitrile or Neoprene Cover: Coupled and Fully Assembled.

Application for Intended Use: May be used for Temporary Service Petroleum/Oily Waste Transfer Systems, or Shipboard Seawater / Fresh Water Suction/Discharge Services.

Description:

1. Size: 1-1/2” I.D. by 50’ long.

2. Nominal OD: 2”

3. Vacuum: Full

4. Working Pressure: 250 PSI minimum.

5. Burst Pressure: 1,000 PSI minimum.

6. Rated Bend Radius: 6 Inches or less.

7. Rated Continuous Temperature: -20ºF to 180ºF

Construction:

8. Tube: Extruded specially compounded Nitrile synthetic rubber. Must meet Rubber Manufacturers Association

(RMA) Class A standard for high oil resistance. Hose shall be wrapped or mandrel type construction with a heavy enough wall construction to allow the use of crimped or swaged couplings with interlocking ferrules.

9. Reinforcement: Multiple braids of textile fabrics with a high-tensile wire helix.

10. Cover: Specially compounded Nitrile, Neoprene or blended synthetic rubber. The cover shall be smooth, slick finish, not a cloth wrap impression type and shall meet RMA Class B standards for weather, ozone and limited oil resistance.

11. Cover Color: Black cover with a contrasting colored brand strip down the entire lay line with contrasting lettering.

12. Hose end assembly shall be accomplished in accordance with established National Association for Hose

Accessories Distribution (NAHAD) certification standards.

13. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End; Brass, 1-1/2” Cam & Groove Quick Disconnect Adapter by Hose Shank, PT Coupling Co., Part # 15E, Item # 1200515.

b. 2nd Hose End; Brass, 1-1/2” Female Cam & Groove Quick Disconnect Coupler by Hose Shank, with Stainless Steel Passive Locking Device, Cam

Arms, Pins, and Pull Rings, PT Coupling Co., Part # 15CSLII, Item # 1290315L2 .

c. End fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co. “Pro-Grip C50SS Crimp Ferrule Stainless Steel” sized to match the hose and fittings. Hose clamps will not be accepted.

14. All end fittings must be meet Commercial Item Description (CID) A-A-59326.

15. Branding / Marking: Hose shall be continuously ink-branded, stencil painted, or Mylar stripe branded /marked in ½” lettering (minimum), which must be in a contrasting color to the black outer cover of the hose. The lettering shall state as a minimum:

a. Standard Hose Brand/Line/Model number, Petroleum type, Date of Manufacture etc.

b. PSNS & IMF S/99

16. Price quotes for market survey request will not be accepted without the hose, fitting, and ferrule manufacturer cut sheets or product description sheets attached, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone/fax number and manufacturer point of contact. The market survey price quote must reference the manufacturer’s part numbers for the item quoted.

17. All quoting vendors if requested must submit a five-foot long hose assembly at vendor expense, for destructive testing analysis.

18. All Or-Equal offers must be approved by PSNS & IMF Code 260.41 prior to purchase.

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean water as a test medium, at 275 (+10, -0) PSIG for 10 minutes. Each hose is to be certified to the requirements of the United States Coast Guard (USCG) for the transfer of oil over water. Each certified hose is to be assigned by the manufacturer a unique serial number, to be permanently stamped or etch marked on the hose ferrule of each hose end. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards, also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested & USCG certified (100% of hoses) shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date and must correspond to each unique hose serial number.

Applicable regulations: Industrial Process Instruction 0505-904B Ch-3, Codes of Federal Regulations, Title 33, Volume 2, Section 154, and Commercial Item Description (CID) A-A-59326.

CONTRACT ITEM DESCRIPTION: ASW/PETROLEUM / OILY WASTE WATER HOSE ASSEMBLY

2-1/2" ID x 25' Long

Or-Equal Purchase Specification:

Hose, Nonmetallic, Nitrile Tube & Nitrile or Neoprene Cover: Coupled and Fully Assembled.

Application for Intended Use: May be used for Temporary Service Petroleum/Oily Waste Transfer Systems, or Shipboard Seawater / Fresh Water Suction/Discharge Services.

1. Size: 2-1/2” I.D. by 25’ long.

2. Nominal OD: 3”

3. Vacuum: Full

4. Working Pressure: 250 PSI, minimum.

5. Burst Pressure: 1,000 PSI, minimum.

6. Rated bend radius: 10 inches or less.

7. Rated Continuous Temperature: -20ºF to 180ºF

Construction:

1. Tube: Extruded specially compounded Nitrile synthetic rubber. Must meet Rubber Manufacturers Association

(RMA) Class A standard for high oil resistance. Hose shall be wrapped or mandrel type construction with a heavy enough wall construction to allow the use of crimped or swaged couplings with interlocking ferrules.

2. Reinforcement: Multiple braids of textile fabric with a high-tensile wire helix.

3. Cover: Specially compounded Nitrile, Neoprene or blended synthetic rubber. The cover shall be smooth slick finish, not a cloth wrap impression type, and shall meet RMA Class B standards for weather, ozone and limited oil resistance.

4. Cover Color: Black cover with a contrasting Red colored brand strip down the entire lay line with contrasting lettering.

5. Hose end assembly shall be accomplished in accordance with established National Association for Hose Accessories

Distribution (NAHAD) certification standards.

6. Each hose assembly shall have the following components installed at each end:

•1st Hose End; Brass, 2-1/2” Male Cam & Groove Adapter by Hose Shank. PT Coupling Co., Part # 25E, Item # 1200525.

•2nd Hose End; Brass, 2-1/2” Female Cam & Groove Coupler by Hose Shank, with Stainless Steel Cam Arms, Pins, Pull

Rings and Passive Locking Device. PT Coupling Co., Part # 25CSLII, Item # 1290325L2.

•End fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co., “ProGrip" C50SS CRIMP

FERRULE STAINLESS STEEL. Ferrules to be sized to match the hose and fittings.

No “or equal” bands, hose clamps, or sleeves will be accepted.

7. All end fittings must be made from US virgin brass with a machined finish IAW Commercial Item Description (CID) A-A-59326 and shall have a working pressure of 250 PSI or greater. Any manufacturers hose end coupling offered other than the above referenced part numbers must be approved by PSNS Code 260.41.

8. Branding / Marking: Hose shall be continuously ink-branded, stencil painted, Mylar or stripe branded /marked in ½” lettering (minimum), which must be in a contrasting color to the Red band strip and black outer cover of the hose.

The lettering shall state as a minimum:

a. Standard Hose Brand/Line/Model number, Petroleum type, Date of Manufacture etc.

b. PSNS & IMF S/99

9. Price quotes for market survey request will not be accepted without the hose, fitting, and ferrule manufacturer cut sheets or product description sheets attached, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone/fax number and manufacturer point of contact. The market survey price quote must reference the manufacturer’s part numbers for the item quoted.

10. All quoting vendors if requested must submit a five-foot long hose assembly at vendor expense, for destructive testing analysis.

11. All Or-Equal offers must be approved by PSNS & IMF Code 260.41 prior to purchase.

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean water as a test medium, at 275 (+10, -0) PSIG for 10 minutes. Each hose is to be certified to the requirements of the United States Coast Guard (USCG) for the transfer of oil over water. Each certified hose to be assigned by the manufacturer a unique serial number, to be permanently stamped or etch marked on the hose ferrule of each hose end. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards. Also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested & USCG certified (100% of hoses) shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date and must correspond to each unique hose serial number.

Applicable regulations: NAVSHIPYDPUGET Instruction 10330.11C, Cat III, Industrial Process Instruction 0505-904B Ch-3, Codes of Federal Regulations Title 33, Volume 2, Section 154, Commercial Item Description (CID) A-A-59326.

(2-1/2" ID x 50' Long)

Or-Equal Purchase Specification:

Hose, Nonmetallic, Nitrile Tube & Nitrile or Neoprene Cover: Coupled and Fully Assembled.

Application for Intended Use: May be used for Temporary Service Petroleum/Oily Waste Transfer Systems, or Shipboard Seawater / Fresh Water Suction/Discharge Services.

1. Size: 2-1/2” I.D. by 50’ long.

2. Nominal OD: 3”

3. Vacuum: Full

4. Working Pressure: 250 PSI, minimum.

5. Burst Pressure: 1,000 PSI, minimum.

6. Rated bend radius: 10 inches or less.

7. Rated Continuous Temperature: -20º F to 180º F

Construction:

1. Tube: Extruded specially compounded Nitrile synthetic rubber. Must meet Rubber Manufacturers Association

(RMA) Class A standard for high oil resistance. Hose shall be wrapped or mandrel type construction with a heavy enough wall construction to allow the use of crimped or swaged couplings with interlocking ferrules.

2. Reinforcement: Multiple braids of textile fabric with a high-tensile wire helix.

3. Cover: Specially compounded Nitrile, Neoprene or blended synthetic rubber. The cover shall be smooth slick finish, not a cloth wrap impression type, and shall meet RMA Class B standards for weather, ozone and limited oil resistance.

4. Cover Color: Black cover with a contrasting Red colored brand strip down the entire lay line with contrasting lettering.

5. Hose end assembly shall be accomplished in accordance with established National Association for Hose Accessories

Distribution (NAHAD) certification standards.

6. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End; Brass, 2-1/2” Male Cam & Groove Adapter by Hose Shank. PT Coupling Co., Part # 25E, Item # 1200525.

b. 2nd Hose End; Brass, 2-1/2” Female Cam & Groove Coupler by Hose Shank, with Stainless Steel Cam Arms, Pins, Pull Rings, and Passive Locking Device. PT Coupling Co., Part # 25CSLII, Item # 1290325L2.

c. End fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co. “Pro-Grip" C50SS CRIMP

FERRULE STAINLESS STEEL. Ferrules to be sized to match the hose and fittings.

No “or equal” bands, hose clamps, or sleeves will be accepted.

7. All end fittings must be made from virgin brass, meet Commercial Item Description (CID) A-A-59326 and shall have a working pressure of 250 PSI or greater. Any manufacturers hose end coupling offered other than the above referenced part numbers must be approved by PSNS Code 260.41.

8. Branding / Marking: Hose shall be continuously ink-branded, stencil painted, Mylar or stripe branded /marked in ½” lettering (minimum), which must be in a contrasting color to the Red band strip and black outer cover of the hose?

The lettering shall state as a minimum:

a. Standard Hose Brand/Line/Model number, Petroleum type, Date of Manufacture etc.

b. PSNS & IMF S/99

9. Price quotes for market survey request will not be accepted without the hose, fitting, and ferrule manufacturer cut sheets or product description sheets attached, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone/fax number and manufacturer point of contact. The market survey price quote must reference the manufacturer’s part numbers for the item quoted.

10. All quoting vendors if requested must submit a five-foot long hose assembly at vendor expense, for destructive testing analysis.

11. All Or-Equal offers must be approved by PSNS & IMF Code 260.41 prior to purchase.

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean water as a test medium, at 275 (+10, -0) PSIG for 10 minutes. Each hose is to be certified to the requirements of the United States Coast Guard (USCG) for the transfer of oil over water. Each certified hose is to be assigned by the manufacturer a unique serial number, to be permanently stamped or etch marked on the hose ferrule of each hose end. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards, also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested & USCG certified (100% of hoses) shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date and must correspond to each unique hose serial number.

Applicable regulations: NAVSHIPYDPUGET Instruction 10330.11C, Cat III, Industrial Process Instruction 0505-904B. Codes of Federal Regulations, Title 33, Volume 2, Section 154, and Commercial Item Description (CID) A-A-59326.

CONTRACT ITEM DESCRIPTION: PETROLEUM / OILY WASTE WATER / SEAWATER OR FRESHWATER SUCTION/DISCHARGE HOSE ASSEMBLY (4" I.D. x 25' Long)

Or-Equal Purchase Specification:

Hose, Nonmetallic, Nitrile Tube & Nitrile or Neoprene Cover: Coupled and Fully Assembled.

Application or Intended Use: May be used for Temporary Service Petroleum/Oily Waste Transfer Systems, or Shipboard Seawater / Fresh Water Suction/Discharge Services.

1) Size: 4” I.D. by 25’ long.

2) Nominal OD: 4-3/4”

3) Vacuum: Full

4) Working Pressure: 250 PSI, minimum.

5) Burst Pressure: 1,000 PSI, minimum.

6) Rated bend radius: 18 inches or less.

7) Rated Continuous Temperature: -20ºF to 180ºF

Construction:

8) Tube: Extruded specially compounded Nitrile synthetic rubber. Must meet Rubber Manufacturers Association (RMA) Class A standard for high oil resistance. Hose shall be wrapped or mandrel type construction with a heavy enough wall construction to allow the use of crimped or swaged couplings with interlocking ferrules.

9) Reinforcement: Multiple braids of textile fabrics with a high-tensile wire helix.

10) Cover: Specially compounded Nitrile, Neoprene or blended synthetic rubber. The cover shall be smooth, not cloth wrap impression type and shall meet RMA Class B standards for weather, ozone and limited oil resistance.

11) Cover Color: Black cover with a contrasting Red colored brand strip down the entire lay line with contrasting lettering.

12) Hose end assembly shall be accomplished in accordance with established National Association for Hose Accessories Distribution (NAHAD) certification standards.

13) Each hose assembly shall have the following components installed at each end:

A. 1st Hose End; Brass, 4” Heavy Duty Male Cam & Groove Adapter by Hose Shank. PT Coupling Co., Part # 40EHD, Item # 1200540H.

B. 2nd Hose End; Brass, 4” Heavy Duty Female Cam & Groove Coupler by Hose Shank with Stainless Steel Cam Arms, Pins, and Pull

Rings. PT Coupling Co. Part # 40CHD, Item # 1200340H.

C. End Fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co., “Pro-Grip C50SS Stainless Steel

Crimp Ferrule”, sized to match the hose and fittings. No “or equal” hose clamps or bands will be accepted.

14) All end fittings must be made from virgin brass and meet Commercial Item Description (CID) A-A-59326 and shall have a working pressure of 250 PSI or greater. Any manufacturers hose end coupling offered other than the above referenced part numbers must be approved by PSNS Code 260.41.

15) Branding / Marking: Hose shall be continuously ink-branded, stencil painted, Mylar or stripe branded /marked in ½” lettering (minimum), which must be in a contrasting color to the RED band strip and black outer cover of the hose. The lettering shall state as a minimum:

A. Standard Hose Brand/Line/Model number, Petroleum type, Date of Manufacture etc.

B. PSNS & IMF S/99

16) Price quotes for market survey request will not be accepted without the hose, fitting, and ferrule manufacturer cut sheets or product description sheets attached, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone/fax number and manufacturer point of contact. The market survey price quote must reference the manufacturer’s part numbers for the item quoted.

17) All quoting vendors if requested must submit a five-foot long hose assembly at vendor expense, for destructive testing analysis.

18) All Or-Equal offers must be approved by PSNS & IMF Code 260.41 prior to purchase.

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean water as a test medium, at 275 (+10, -0) PSIG for 10 minutes. Each hose is to be certified to the requirements of the United States Coast Guard (USCG) for the transfer of oil over water. Each certified hose is to be assigned by the manufacturer a unique serial number, to be permanently stamped or etch marked on the hose ferrule of each hose end. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards. Also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested & USCG certified (100% of hoses) shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date and must correspond to each unique hose serial number.

Applicable regulations: PSNS&IMFINST 10330.11E, PSNS&IMFINST 11300.10K, Industrial Process Instruction 0505- 904B CH-3, Code of Federal Regulations Title 33, Volume 2, Section 154, and Commercial Item Description (CID) A-A- 59326.

P:\PME\4200.08 Contract Files\Quist, Denise\BREMERTON\FY24\FY24 SOLICITATIONS\24Q0262 32966421 HOSE FLEX\A. Pre-Solicitation\A1.

Requirements\SALIENT CHARACTERISTICS\32966427 CHT Hose Assy.doc Last revised 06/11/2011

CONTRACT ITEM DESCRIPTION: 2-1/2” SEWAGE (CHT) DISCHARGE HOSE ASSEMBLY

(2-1/2” ID X 25’ LONG)

(COMMERICALLY CALLED “SEWAGE TRANSFER” HOSE

Or Equal Purchase Specification: Coupled and fully assembled.

Hose, Nonmetallic, Multiple Tube & Cover with helix wire construction; Coupled and Fully Assembled,

1. Size: 2-1/2” I.D. by 25’ Long.

2. Application: Temporary Marine (CHT) Ship to Shore Sewage Discharge Services.

3. Working Pressure: 150 PSI, minimum.

4. Burst Pressure: 600 PSI, minimum.

5. Vacuum Rating: 29 Hg

6. Rated bend radius: 9” inches or less.

7. Rated Continuous Temperature: -25º F to +180º F.

8. If requested all bidding vendors must submit: a hose, end fitting, and ferrule manufacturer cut sheet or product description sheet attachments, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone, fax number and manufacturer point of contact.

9. All quoting vendors if requested must submit a five-foot long hose assembly to Shop 99 at vendor’s expense, for destructive testing analysis prior to PSNS & IMF Engineering Code 270TS approval to purchase.

10. PSNS & IMF Engineering Code 270TS must approve all exceptions and Or-Equal offer’s prior to purchase.

Construction:

1. Tube: Black, Nitrile, must meet Rubber Manufacturers Association (RMA) Class A standards for oil resistance.

Hose shall be wrapped or mandrel type construction.

2. Reinforcement: Multiple spiral plied fabric helix construction.

3. Cover: Smooth Cover, Black synthetic rubber, Neoprene or blend, must meet minimum of RMA Class C standards for limited oil resistance.

4. Cover Color: Black (No continuous yellow accepted).

5. Hose end assembly shall be accomplished in accordance with established National Association for Hose &

Accessories Distribution (NAHAD) certification standards.

6. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End; Brass, 2-1/2” Male Cam & Groove Adapter by Hose Shank, PT Coupling Co., Part # 25E, Item # 1200525.

b. 2nd Hose End; Brass, 2-1/2” Female Cam & Groove Coupler by Hose Shank with Stainless Steel, Cam Arms, Pins, Pull Rings and Passive Locking Device, PT Coupling Co., Part # 25CSLII, Item # 1290325L2.

c. Hose end fittings to comply with COMMERCIAL ITEM DESCRIPTION (CID) A-A-59326/2 and A-A-59326/6.

d. End Fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co., “ProGrip”

C50SS Stainless Steel Crimp Ferrule or equal, sized to match the hose. End fittings shall meet a working pressure of 150 PSI or greater. (“Or equal” must be interlocking ferrule type system, no hose clamps, bands, or sleeves will be accepted).

7. Branding / Marking: Hose shall be continuously ink-branded, stencil painted, Mylar or stripe branded, marked in 1-1/2” lettering (minimum), which must be in a contrasting color or background to the black outer cover of the hose.

The lettering shall state as a minimum:

a. Hose Brand/Line/Model Number, Date of Manufacture.

b. PSNS S/99 CHT SEWAGE

c. 150 PSI MAX

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean (Potable) water as a test medium, at 225 (+20, -0) PSIG for 10 minutes. Each hose to be certified to the testing procedures of the United States Coast Guard (USCG) regulations 33 C.F.R & 154.500 hose assemblies. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards. Also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested & USCG certified (100% of hoses) shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date.

P:\PME\4200.08 Contract Files\Quist, Denise\BREMERTON\FY24\FY24 SOLICITATIONS\24Q0262 32966421 HOSE FLEX\A. Pre-Solicitation\A1.

Requirements\SALIENT CHARACTERISTICS\32966428 CHT Hose Assy.doc Last revised 06/11/2011

CONTRACT ITEM DESCRIPTION: 2-1/2” SEWAGE (CHT) DISCHARGE HOSE ASSEMBLY

(2-1/2” ID X 50’ LONG)

(COMMERICALLY CALLED “SEWAGE TRANSFER” HOSE

Or Equal Purchase Specification: Coupled and fully assembled.

Hose, Nonmetallic, Multiple Tube & Cover with helix wire construction; Coupled and Fully Assembled,

1. Size: 2-1/2” I.D. by 50’ Long.

2. Application: Temporary Marine (CHT) Ship to Shore Sewage Discharge Services.

3. Working Pressure: 150 PSI, minimum.

4. Burst Pressure: 600 PSI, minimum.

5. Vacuum Rating: 29 Hg

6. Rated bend radius: 9” inches or less.

7. Rated Continuous Temperature: -25º F to +180º F.

8. If requested all bidding vendors must submit: a hose, end fitting, and ferrule manufacturer cut sheet or product description sheet attachments, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone, fax number and manufacturer point of contact.

9. All quoting vendors if requested must submit a five-foot long hose assembly to Shop 99 at vendor’s expense, for destructive testing analysis prior to PSNS & IMF Engineering Code 270TS approval to purchase.

10. PSNS & IMF Engineering Code 270TS must approve all exceptions and Or-Equal offer’s prior to purchase.

Construction:

1. Tube: Black, Nitrile, must meet Rubber Manufacturers Association (RMA) Class A standards for oil resistance.

Hose shall be wrapped or mandrel type construction.

2. Reinforcement: Multiple spiral plied fabric helix construction.

3. Cover: Smooth Cover, Black synthetic rubber, Neoprene or blend, must meet minimum of RMA Class C standards for limited oil resistance.

4. Cover Color: Black (No continuous yellow accepted).

5. Hose end assembly shall be accomplished in accordance with established National Association for Hose &

Accessories Distribution (NAHAD) certification standards.

6. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End; Brass, 2-1/2” Male Cam & Groove Adapter by Hose Shank, PT Coupling Co., Part # 25E, Item # 1200525.

b. 2nd Hose End; Brass, 2-1/2” Female Cam & Groove Coupler by Hose Shank with Stainless Steel, Cam Arms, Pins, Pull Rings and Passive Locking Device, PT Coupling Co., Part # 25CSLII, Item # 1290325L2.

c. Hose end fittings to comply with COMMERCIAL ITEM DESCRIPTION (CID) A-A-59326/2 and A-A-59326/6.

d. End Fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co., “ProGrip”

C50SS Stainless Steel Crimp Ferrule or equal, sized to match the hose. End fittings shall meet a working pressure of 150 PSI or greater. (“Or equal” must be interlocking ferrule type system, no hose clamps, bands, or sleeves will be accepted).

7. Branding / Marking: Hose shall be continuously ink-branded, stencil painted, Mylar or stripe branded, marked in 1-1/2” lettering (minimum), which must be in a contrasting color or background to the black outer cover of the hose.

The lettering shall state as a minimum:

a. Hose Brand/Line/Model Number, Date of Manufacture.

b. PSNS S/99 CHT SEWAGE

c. 150 PSI MAX

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean (Potable) water as a test medium, at 225 (+20, -0) PSIG for 10 minutes. Each hose to be certified to the testing procedures of the United States Coast Guard (USCG) regulations 33 C.F.R & 154.500 hose assemblies. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards. Also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested & USCG certified (100% of hoses) shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date.

P:\PME\4200.08 Contract Files\Quist, Denise\BREMERTON\FY24\FY24 SOLICITATIONS\24Q0262 32966421 HOSE FLEX\A. Pre-Solicitation\A1. Requirements\SALIENT CHARACTERISTICS\32966426 ASW - Petroleum Hose Assy Description.doc Last revised 04/18/2011

CONTRACT ITEM DESCRIPTION: PETROLEUM / OILY WASTE WATER / SEAWATER OR FRESHWATER SUCTION/DISCHARGE HOSE ASSEMBLY (4" I.D. x 50' Long)

Or-Equal Purchase Specification:

Hose, Nonmetallic, Nitrile Tube & Nitrile or Neoprene Cover: Coupled and Fully Assembled.

Application or Intended Use: May be used for Temporary Service Petroleum/Oily Waste Transfer Systems, or Shipboard Seawater / Fresh Water Suction/Discharge Services.

1. Size: 4” I.D. by 50’ long.

2. Nominal OD: 4-3/4”

3. Vacuum: Full

4. Working Pressure: 250 PSI, minimum.

5. Burst Pressure: 1,000 PSI, minimum.

6. Rated bend radius: 18 inches or less.

7. Rated Continuous Temperature: -20ºF to 180ºF

Construction:

8. Tube: Extruded specially compounded Nitrile synthetic rubber. Must meet Rubber Manufacturers Association (RMA) Class A standard for high oil resistance. Hose shall be wrapped or mandrel type construction with a heavy enough wall construction to allow the use of crimped or swaged couplings with interlocking ferrules.

9. Reinforcement: Multiple braids of textile fabrics with a high-tensile wire helix.

10. Cover: Specially compounded Nitrile, Neoprene or blended synthetic rubber. The cover shall be smooth, not cloth wrap impression type and shall meet RMA Class B standards for weather, ozone and limited oil resistance.

11. Cover Color: Black cover with a contrasting Red colored brand strip down the entire lay line with contrasting lettering.

12. Hose end assembly shall be accomplished in accordance with established National Association for Hose Accessories Distribution (NAHAD) certification standards.

13. Each hose assembly shall have the following components installed at each end:

A. 1st Hose End; Brass, 4” Heavy Duty Male Cam & Groove Adapter by Hose Shank, PT Coupling Co., Part # 40EHD, Item # 1200540H.

B. 2nd Hose End; Brass, 4” Heavy Duty Female Cam & Groove Coupler by Hose Shank with 316 Stainless Steel Cam Arms, Pins, Pull Rings, and Passive

Locking Device. PT Coupling Co., Part # 40CHD, Item # 1200340H.

C. End fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co., “Pro-Grip C50SS” Stainless Steel Crimp Ferrules sized to match the hose. No “or equal” hose clamps accepted.

14. All end fittings must be made from US virgin brass with a machined finish IAW Commercial Item Description (CID) A-A-59326 and shall have a working pressure of 250 PSI or greater. Any manufacturers hose end couplings offered other than the above referenced part numbers must be approved by PSNS Code 260.41.

15. Branding / Marking: Hose shall be continuously Ink Branded, stencil painted, Mylar, or Stripe Branded, marked in ½” lettering (minimum), which must be in a contrasting color to the RED band strip and black outer cover of the hose. The lettering shall state as a minimum:

A. Standard Hose Brand/Line/Model Number, Petroleum type, Date of Manufacture etc.

B. PSNS & IMF S/99

16. Price quotes for market survey request will not be accepted without the hose, fitting, and ferrule manufacturer cut sheets or product description sheets attached, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone/fax number and manufacturer point of contact. The market survey price quote must reference the manufacturer’s part numbers for the item quoted.

17. All quoting vendors if requested must submit a five-foot long hose assembly at government expense, for destructive testing analysis.

18. All Or-Equal offers must be approved by PSNS & IMF Code 260.41 prior to purchase.

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean water as a test medium, at 275 (+10,-0) PSIG for 10 minutes. Each hose is to be certified to the requirements of the United States Coast Guard (USCG) for the transfer of oil over water. Each certified hose is to be assigned by the manufacturer a unique serial number, to be permanently stamped or etch marked on the hose ferrule of each hose end. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards, also that the hose does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested & USCG certified (100% of hoses) shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date and must correspond to each unique hose serial number.

Applicable regulations: PSNS&IMFINST 10330.11E, PSNS&IMFINST 11300.10K, Industrial Process Instruction 0505- 904B CH-3, Codes of Federal Regulations Title 33, Volume 2, Section 154, and Commercial Item (CID) A-A- 59326.

P:\PME\4200.08 Contract Files\Quist, Denise\BREMERTON\FY24\FY24 SOLICITATIONS\24Q0262 32966421 HOSE FLEX\A. Pre-Solicitation\A1.

Requirements\SALIENT CHARACTERISTICS\32966429 CHT Hose Assy.doc

Last revised 06/11/2011

CONTRACT ITEM DESCRIPTION: 4” SEWAGE (CHT) DISCHARGE HOSE ASSEMBLY

(4” ID X 25’ LONG)

(COMMERICALLY CALLED “SEWAGE TRANSFER” HOSE

Or Equal Purchase Specification: Coupled and fully assembled.

Hose, Nonmetallic, Multiple Tube & Cover with helix wire construction; Coupled and Fully Assembled,

1. Size: 4” I.D. by 25’ long.

2. Application: Temporary Marine (CHT) Ship to Shore Sewage Discharge Services.

3. Working Pressure: 150 PSI, minimum.

4. Burst Pressure: 600 PSI, minimum.

5. Vacuum Rating: 29 Hg

6. Rated bend radius: 12” inches or less.

7. Rated Continuous Temperature: -25º F to 180º F.

8. If requested all bidding vendors must submit: a hose, end fitting, and ferrule manufacturer cut sheet or product description sheet attachments, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone, fax number and manufacturer point of contact.

9. All quoting vendors if requested must submit a five-foot long hose assembly to Shop 99 at vendor’s expense, for destructive testing analysis prior to PSNS & IMF Engineering Code 270TS approval to purchase.

10. PSNS & IMF Engineering Code 270TS must approve all exceptions and Or-Equal offer’s prior to purchase.

Construction:

1. Tube: Black Nitrile, must meet Rubber Manufacturers Association (RMA) Class A standards for oil resistance.

Hose shall be wrapped or mandrel type construction.

2. Reinforcement: Multiple spiral piled fabric helix construction.

3. Cover: Smooth (corrugated cover is not acceptable), Black synthetic rubber, Neoprene or blend, must meet RMA

Class C standards for limited oil resistance.

4. Cover Color: Black (No continuous yellow accepted).

5. Hose end assembly shall be accomplished in accordance with established Association for Hose & Accessories

Distribution (NAHAD) certification standards.

6. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End; Brass, 4” Male Cam & Groove Quick Disconnect Adapter by Hose Shank, PT Coupling Co., Part # 40E, Item # 1200540.

b. 2nd Hose End; Brass, 4” Female Cam & Groove Quick Disconnect Coupler by Hose Shank with Stainless Steel Cam Arms, Pins, Pull Rings, and Passive Locking Device, PT Coupling Co., Part # 40CHD, Item # 1200340H.

c. Hose end fittings to comply with COMMERCIAL ITEM DESCRIPTION (CID) A-A-59326/2 and A-A-59326/6.

d. End Fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co., “ProGrip”

C50SS Stainless Steel Crimp Ferrule sized to match the hose and fittings. End fittings shall meet a working pressure of 150 PSI or greater. Must be interlocking ferrule type system, no hose clamps or bands will be accepted.

7. Branding / Marking: Hose shall be continuously ink-branded, stencil painted, Mylar or stripe branded /marked in 1-1/2” lettering (minimum), which must be in a contrasting color or background to the black outer cover of the hose.

The lettering shall state as a minimum:

a. Hose Brand/Line/Model number, Date of Manufacture.

b. PSNS S/99 CHT SEWAGE

c. 150 PSI MAX

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean water as a test medium, at 225 (+20, -0) PSIG for 10 minutes. Each hose is to be certified to the testing procedures of the United States Coast Guard (USCG) regulations 33 C.F.R & 154.500 hose assemblies. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards. Also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested & USCG certified (100% of hoses) shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date.

CONTRACT ITEM DESCRIPTION: 4” SEWAGE (CHT) DISCHARGE HOSE ASSEMBLY

(4” ID X 50’ LONG)

(COMMERICALLY CALLED “SEWAGE TRANSFER” HOSE

Or Equal Purchase Specification: Coupled and fully assembled.

Hose, Nonmetallic, Multiple Tube & Cover with helix wire construction; Coupled and Fully Assembled,

1. Size: 4” I.D. by 50’ long.

2. Application: Temporary Marine (CHT) Ship to Shore Sewage Discharge Services.

3. Working Pressure: 150 PSI, minimum.

4. Burst Pressure: 600 PSI, minimum.

5. Vacuum Rating: 29 Hg

6. Rated bend radius: 12” inches or less.

7. Rated Continuous Temperature: -25º F to 180º F.

8. If requested all bidding vendors must submit: a hose, end fitting, and ferrule manufacturer cut sheet or product description sheet attachments, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone, fax number and manufacturer point of contact.

9. All quoting vendors if requested must submit a five-foot long hose assembly to Shop 99 at vendor’s expense, for destructive testing analysis prior to PSNS & IMF Engineering Code 270TS approval to purchase.

10. PSNS & IMF Engineering Code 270TS must approve all exceptions and Or-Equal offer’s prior to purchase.

Construction:

1. Tube: Black, Nitrile, must meet Rubber Manufacturers Association (RMA) Class A standards for oil resistance.

Hose shall be wrapped or mandrel type construction.

2. Reinforcement: Multiple spiral plied fabric helix construction.

3. Cover: Smooth (corrugated cover is not acceptable), Black synthetic rubber, Neoprene or blend, must meet RMA

Class C standards for limited oil resistance.

4. Cover Color: Black (No continuous yellow accepted).

5. Hose end assembly shall be accomplished in accordance with established National Association for Hose &

Accessories Distribution (NAHAD) certification standards.

6. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End; Brass, 4” Male Cam & Groove Quick Disconnect Adapter by Hose Shank, PT Coupling Co., Part # 40E, Item # 1200540.

b. 2nd Hose End; Brass, 4” Heavy Duty Female Cam & Groove Quick Disconnect Coupler by Hose Shank with Stainless Steel Passive Locking Cam Arms and Pins, PT Coupling Co., Part # 40CHD, Item # 1200340H.

c. Hose end fittings to comply with COMMERCIAL ITEM DESCRIPTION (CID) A-A-59326/2 and A-A-59326/6.

d. End Fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co., “ProGrip”

C50SS Stainless Steel Crimp Ferrule, sized to match the hose. End fittings shall meet a working pressure of 150 PSI or greater. Must be interlocking ferrule type system, no hose clamps, bands or sleeves will be accepted.

7. Branding / Marking: Hose shall be continuously ink-branded, stencil painted, Mylar or stripe branded, marked in 1-1/2” lettering (minimum), which must be in a contrasting color or background to the black outer cover of the hose.

The lettering shall state as a minimum:

a. Hose Brand/Line/Model Number, Date of Manufacture.

b. PSNS S/99 CHT SEWAGE

c. 150 PSI MAX

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean water as a test medium, at 225 (+20, -0) PSIG for 10 minutes. Each hose is to be certified to the testing procedures of the United States Coast Guard (USCG) regulations 33 C.F.R & 154.500 hose assemblies. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards, also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested & USCG certified (100% of hoses) shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date.