SPMYM2-20-Q-2900 (SALIENT CHARACTERISTICS) GIANT HYDRO BLASTER.pdf

Salient Characteristics for a 10,000 PSI Hydro Blaster

Project # 011-340

14 Aug 20

1. One (1) 10,000 PSI Hydro Blaster (Bens Cleaner Sales Inc., Giant Hydro Blaster, 10 GPM @

10,000 PSI) This 10,000 PSI Hydro Blaster shall be a “Turn-Key and a Stand-Alone” system, and shall include the following minimum (or equal) features:

a. 10 GPM @ 10,000 PSI

b. Giant GP7122 Pump

c. 13 GPM @ 15,000 PSI Unloader

d. 75 HP Baldor Motor, 1780 RPM, 460 Volt, 3 Phase

e. Control Panel Mounted to Frame w/ On/Off Switch, E-Stop & Soft Start

f. Painted Steel Frame with Forklift Slots

g. Electric Driven Boost Pump

h. Pressure Gauge

i. Oil Drain Kit

j. Float Tank – 100 Gallon

k. NRTL Certified (see paragraph 4)

2. No Asbestos – No asbestos products/materials shall be used in any components (i.e. gaskets, etc.) of the equipment, or in any of the options/consumables and other accessories. The equipment shall be asbestos free.

3. Three (3) Hard Copies of Operator Manuals – Which shall include detailed instructions on how to operate the software, etc. Operator / Maintenance / Repair Manuals - The equipment shall be furnished with three (3) [NOTE: Or specify number of copies] hard copies of the manufacturer’s standard

Operation, Maintenance, and Repair Manual(s), bound in durable three ring binder(s). The manuals shall include all mechanical and electrical schematics showing discrete components/block diagrams/wiring diagrams with inputs and outputs identified/system electrical interface documents and drawings for the specific model of all machine equipment/drives/controls supplied. The information contained in the manual(s) shall reflect the unit and its components in the “as built” configuration. The information contained in the manual(s) shall be adequate to permit trouble shooting and repair of the equipment by journeymen level personnel. The information contained in the manual(s) shall be in the English language. The information contained in the manual(s) shall be in imperial units of measure. The vendor shall provide a “no asbestos used” statement, certifying that all products/materials (i.e. gaskets, etc.) used in the components of the equipment does not contain asbestos, as outlined in paragraph 2f. The contractor shall provide a list of recommended consumable spare parts and possible sources for procurement.

4. NRTL Certification Report - This includes the equipment and its component parts shall be in compliance with applicable Code of Electrical Regulations (CFR) Title 29, Part 1910. By definition, any equipment will be deemed acceptable and approved by TRF, Bangor, if it meets specific Occupational

Safety and Health Administration (OSHA) conditions outlined in CFR Title 29, Part 1910; Subparts "O" and "S". Specifically, equipment will be "Accepted" by TRF, Bangor, if it has been inspected and found by a Nationally Recognized Testing Laboratory (NRTL) to conform to specified plans or procedures of applicable codes. The equipment (as a whole system) shall be Nationally Recognized Testing Laboratory

(NRTL) inspected and certified (by an OSHA authorized third party). One (1) “hard” copy of the NRTL certification report shall be provided. If the equipment type/model has already been NRTL inspected and certified, a certification report (one (1) ”hard” copy) or documentation mounted on the equipment, (which acknowledges it is NRTL certified), shall be provided.

5. Warranty - The warranty period shall be for one year. Supplies and services furnished shall be covered by warranty from defects in design, materials and workmanship. The warranty shall be the manufacturer’s standard commercial warranty, which shall conform to all the requirements of the contract. Acceptance of the manufacturer’s standard commercial warranty shall not minimize the rights of the government under clauses in the contract, and in any conflict that arises between the terms and conditions of the contract and manufacturer’s warranty, the terms and conditions of the contract shall take precedence. The warranty period shall commence from the date of acceptance. All warranty work shall be provided by a factory authorized distributer.