SPMYM1-18-Q-0001.docx

SPMYM118Q0001

Section SF 1449 - CONTINUATION SHEET

N421587279B192

FFP

CAP SCREW, HEX HEAD,

SEVEN EIGHTS INCH -9UNC-2A X THREE AND FIVE EIGHTS INCHES LONG, MONEL QQ-N-281D, MIL-S-122J

ORDERING DATA

A) GENERAL SPECIFICATIONS FOR STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATION WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; MIL-DTL-1222J; 08 DECEMBER 2000 B) HEX HEAD CAP SWREW, SEVEN EIGHTS INCH -9UNC-2A X THREE AND FIVE EIGHTS INCHES LONG, TYPE I, QQ-N-281, ALLOY TYPE; NICKEL ALLOY GRADE 400 AS FORMED OR STRESS RELIEVED, UNCOATED

C) LATEST REVISION

D) NA

E) NA

F-J) NA

K) LOCKING ELEMENT NOT REQUIRED

L) AS SPECIFIED

NOTE: WHERE HEADED FASTENERS SPECIFICATIONS REQUIRE A YIELD STRENGTH TEST AND A WEDGE TENSILE TEST, A SEPARAATE (NEW, UNTESTED) FASTENER IS REQUIRED FOR EACH OF THE TWO METHODS, AND BOTH OF THESE TESTS SHALL BE REPORTED.

N) NA

O) NA

P) NA

Q) SCREWS TO BE INSPECTED IAW 4.3.2 AND 4.3.2.1

R) ACCEPTANCE CRITERIA IAW 4.3.2 AND 4.3.2.1

S) NODESTRUCTIVE TESTING AND ACCEPTANCE CRITERIA SHALL BE IAW 4.3.3

T) MECHANICAL TEST ARE TO BE DONE AFTER FINAL HEAT TREATMENT

U) IAW 5.1

V) -BB) NA

Certification Requirements:

Provide written verification that the chemical and mechanical properties have been determined and are acceptable as follows.

a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contains a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Test reports for loose MIL-DTL-1222, K-Monel (QQ-N-286), fasteners and for all assemblies which contain MIL-DTL-1222, K-Monel fasteners, shall include a certification statement describing the forming process used to manufacture the fasteners (i.e. hot headed with cold rolled threads, hot headed with machined threads, etc.), the heat treatments performed, and the order in which these actions were performed(i.e. fasteners manufactured and then solution annealed and age hardened, etc.). This action is required to ensure compliance with MIL-DTL-1222, paragraph 3.3.4, which requires fasteners with formed heads (i.e., hot headed, cold headed, etc.) and rolled threads to be solution annealed and age hardened after the manufacturing process.

(e) Certification for QQ-N-286 Rev G materials shall show that slow strain rate tensile (SSRT) test of “start material” has been accomplished per QQ-N-286 Rev G requirements.

(f) Where headed fastener specification require a yield strength test AND a wedge tensile test, a separate (new, untested) fastener is required for each of the two test methods, and both of these test shall be reported.

FOB: Destination

MILSTRIP: N421587279B192

PURCHASE REQUEST NUMBER: N421587279B192

PROJECT: 5T9

NET AMT

N421587279B193

CAP SCREW, HEX HEAD ONE AND ONE QUARTER INCH, 7 UNC-2A X FIVE AND THREE QUARTER INCHES LONG, MONEL, QQ-N-281-D, MIL-S-1222J

ORDERING DATA

A) GENERAL SPECIFICATIONS FOR STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATION WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; MIL-DTL-1222J; 08 DECEMBER 2000 B) HEX HEAD CAP SWREW, ONE AND ONE QUARTER INCH, 7 UNC-2A X FIVE AND THREE QUARTER INCHES LONG, TYPE I, QQ-N-281, ALLOY TYPE; NICKEL ALLOY GRADE 400 AS FORMED OR STRESS RELIEVED, UNCOATED

C) LATEST REVISION

D) NA

E) NA

F-J) NA

K) LOCKING ELEMENT NOT REQUIRED

L) AS SPECIFIED

NOTE: WHERE HEADED FASTENERS SPECIFICATIONS REQUIRE A YIELD STRENGTH TEST AND A WEDGE TENSILE TEST, A SEPARAATE (NEW, UNTESTED) FASTENER IS REQUIRED FOR EACH OF THE TWO METHODS, AND BOTH OF THESE TESTS SHALL BE REPORTED.

N) NA

O) NA

P) NA

Q) SCREWS TO BE INSPECTED IAW 4.3.2 AND 4.3.2.1

R) ACCEPTANCE CRITERIA IAW 4.3.2 AND 4.3.2.1

S) NODESTRUCTIVE TESTING AND ACCEPTANCE CRITERIA SHALL BE IAW 4.3.3

T) MECHANICAL TEST ARE TO BE DONE AFTER FINAL HEAT TREATMENT

U) IAW 5.1

V) -BB) NA

Certification Requirements:

Provide written verification that the chemical and mechanical properties have been determined and are acceptable as follows.

a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contains a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Test reports for loose MIL-DTL-1222, K-Monel (QQ-N-286), fasteners and for all assemblies which contain MIL-DTL-1222, K-Monel fasteners, shall include a certification statement describing the forming process used to manufacture the fasteners (i.e. hot headed with cold rolled threads, hot headed with machined threads, etc.), the heat treatments performed, and the order in which these actions were performed(i.e. fasteners manufactured and then solution annealed and age hardened, etc.). This action is required to ensure compliance with MIL-DTL-1222, paragraph 3.3.4, which requires fasteners with formed heads (i.e., hot headed, cold headed, etc.) and rolled threads to be solution annealed and age hardened after the manufacturing process.

(e) Certification for QQ-N-286 Rev G materials shall show that slow strain rate tensile (SSRT) test of “start material” has been accomplished per QQ-N-286 Rev G requirements.

(f) Where headed fastener specification require a yield strength test AND a wedge tensile test, a separate (new, untested) fastener is required for each of the two test methods, and both of these test shall be report FOB: Destination

MILSTRIP: N421587279B193

NET AMT

N421587279B194

CAP SCREW HEX HEAD, ONE AND ONE QUARTER INCHES, 7-UNC-3A X FIVE AND ONE HALF INCHES LONG, K MONEL, QQ-N-286-G, MIL-S-1222J

ORDERING DATA

A) GENERAL SPECIFICATIONS FOR STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATION WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; MIL-DTL-1222J; 08 DECEMBER 2000 B) HEX HEAD CAP SWREW, ONE AND ONE QUARTER INCH, 7-UNC-3A X FIVE AND ONE HALF INCH LONG, TYPE I, ALLOY TYPE; GRADE 500, ANNEALED AND AGE HARDENED.

C) LATEST REVISION

D) NA

E) NA

F-J) NA

K) LOCKING ELEMENT NOT REQUIRED

L) AS SPECIFIED

N) NA

O) NA

P) NA

Q) SCREWS TO BE INSPECTED IAW 4.3.2 AND 4.3.2.1

R) ACCEPTANCE CRITERIA IAW 4.3.2 AND 4.3.2.1

S) NODESTRUCTIVE TESTING AND ACCEPTANCE CRITERIA SHALL BE IAW 4.3.3

T) MECHANICAL TEST ARE TO BE DONE AFTER FINAL HEAT TREATMENT

U) IAW 5.1

V) -BB) NA

QQ-N-286G

A) NICKEL-COPPER ALUMINUM ALLOY, WROUGHT (uns N05500); QQ-N-286 G, 07 DECEMBER 2000

B) FORM 2, ANNEALED AND AGED HARDENED, COLD DRAWN

C) LATESTREVISION

D) FORGING SKETCH NOT REQUIRED

E) SIZE REQUIRED TO SUIT MFG. OF FASTENER

F) NOT REQUIRED

G) N/A

H) TOLERANCES ARE TO BE AS SPECIFIED

I) NOT REQUIRED

J) NOT REQUIRED

K. TO SUIT MFG OF FASTENER

L) N/A

M) EDGES AS SPECIFIED

N) TO SUIT MFG OF FASTENERS

O) MARKINGS AS SPECIFIED

P) MECHANICAL TEST REQUIED (NOT FOR RE-FORGING)

Q) N/A

R) SOLUTION ANNEALED AND SSRT IAW 4.3.6.2

S) SSRT LABORATORY SHALL BE AN APPROVED FACILITY

Certification Requirements:

Provide written verification that the chemical and mechanical properties have been determined and are acceptable as follows.

a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contains a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Test reports for loose MIL-DTL-1222, K-Monel (QQ-N-286), fasteners and for all assemblies which contain MIL-DTL-1222, K-Monel fasteners, shall include a certification statement describing the forming process used to manufacture the fasteners (i.e. hot headed with cold rolled threads, hot headed with machined threads, etc.), the heat treatments performed, and the order in which these actions were performed(i.e. fasteners manufactured and then solution annealed and age hardened, etc.). This action is required to ensure compliance with MIL-DTL-1222, paragraph 3.3.4, which requires fasteners with formed heads (i.e., hot headed, cold headed, etc.) and rolled threads to be solution annealed and age hardened after the manufacturing process.

(e) Certification for QQ-N-286 Rev G materials shall show that slow strain rate tensile (SSRT) test of “start material” has been accomplished per QQ-N-286 Rev G requirements.

(f) Where headed fastener specification require a yield strength test AND a wedge tensile test, a separate (new,untested) fastener is required for each of the two test methods, and both of these test shall be report

FOB: Destination

MILSTRIP: N421587279B194

NET AMT

N421587279B195

CAP SCREW HEX HEAD, ONE AND ONE EIGTHS INCHES, 7-UNC-2A X FOUR AND ONE QUARTER INCHES LONG, K MONEL, QQ-N-286-G, MIL-S-1222J

ORDERING DATA

A) GENERAL SPECIFICATIONS FOR STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATION WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; MIL-DTL-1222J; 08 DECEMBER 2000 B) HEX HEAD CAP SWREW, ONE AND ONE EIGTHS INCHES, 7-UNC-2A X FOUR AND ONE QUARTER INCHES LONG, TYPE I, ALLOY TYPE; GRADE 500, ANNEALED AND AGE HARDENED.

C) LATEST REVISION

D) NA

E) NA

F-J) NA

K) LOCKING ELEMENT NOT REQUIRED

L) AS SPECIFIED

N) NA

O) NA

P) NA

Q) SCREWS TO BE INSPECTED IAW 4.3.2 AND 4.3.2.1

R) ACCEPTANCE CRITERIA IAW 4.3.2 AND 4.3.2.1

S) NODESTRUCTIVE TESTING AND ACCEPTANCE CRITERIA SHALL BE IAW 4.3.3

T) MECHANICAL TEST ARE TO BE DONE AFTER FINAL HEAT TREATMENT

U) IAW 5.1

V) -BB) NA

QQ-N-286G

A) NICKEL-COPPER ALUMINUM ALLOY, WROUGHT (uns N05500); QQ-N-286 G, 07 DECEMBER 2000

B) FORM 2, ANNEALED AND AGED HARDENED, COLD DRAWN

C) LATESTREVISION

D) FORGING SKETCH NOT REQUIRED

E) SIZE REQUIRED TO SUIT MFG. OF FASTENER

F) NOT REQUIRED

G) N/A

H) TOLERANCES ARE TO BE AS SPECIFIED

I) NOT REQUIRED

J) NOT REQUIRED

K. TO SUIT MFG OF FASTENER

L) N/A

M) EDGES AS SPECIFIED

N) TO SUIT MFG OF FASTENERS

O) MARKINGS AS SPECIFIED

P) MECHANICAL TEST REQUIED (NOT FOR RE-FORGING)

Q) N/A

R) SOLUTION ANNEALED AND SSRT IAW 4.3.6.2

S) SSRT LABORATORY SHALL BE AN APPROVED FACILITY

Certification Requirements:

Provide written verification that the chemical and mechanical properties have been determined and are acceptable as follows.

a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contains a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Test reports for loose MIL-DTL-1222, K-Monel (QQ-N-286), fasteners and for all assemblies which contain MIL-DTL-1222, K-Monel fasteners, shall include a certification statement describing the forming process used to manufacture the fasteners (i.e. hot headed with cold rolled threads, hot headed with machined threads, etc.), the heat treatments performed, and the order in which these actions were performed(i.e. fasteners manufactured and then solution annealed and age hardened, etc.). This action is required to ensure compliance with MIL-DTL-1222, paragraph 3.3.4, which requires fasteners with formed heads (i.e., hot headed, cold headed, etc.) and rolled threads to be solution annealed and age hardened after the manufacturing process.

(e) Certification for QQ-N-286 Rev G materials shall show that slow strain rate tensile (SSRT) test of “start material” has been accomplished per QQ-N-286 Rev G requirements.

(f) Where headed fastener specification require a yield strength test AND a wedge tensile test, a separate (new,untested) fastener is required for each of the two test methods, and both of these test shall be report FOB: Destination

MILSTRIP: N421587279B195

NET AMT

N421587279B196

CAP SCREW, HEX HEAD, ONE AND ONE QUARTER INCHES 7-UNC-3A X FOUR AND THREE QUARTERS INCHES LONG, MONEL, QQ-N-281D, MIL-S-1222J

ORDERING DATA

A) GENERAL SPECIFICATIONS FOR STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATION WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; MIL-DTL-1222J; 08 DECEMBER 2000 B) CAP SCREW, HEX HEAD, ONE AND ONE QUARTER INCHES 7-UNC-3A X FOUR AND THREE QUARTERS INCHES LONG, TYPE I, QQ-N-281D, ALLOY TYPE; NICKEL, ALLOY GRADE 400 AS FORMED OR STRESS RELIEVED, UNCOUADED

C) LATEST REVISION

D) NA

E) NA

F-J) NA

K) LOCKING ELEMENT NOT REQUIRED

L) AS SPECIFIED

NOTE: WHERE HEADED FASTENERS SPECIFICATIONS REQUIRE A YIELD STRENGTH TEST AND A WEDGE TENSILE TEST, A SEPARAATE (NEW, UNTESTED) FASTENER IS REQUIRED FOR EACH OF THE TWO METHODS, AND BOTH OF THESE TESTS SHALL BE REPORTED.

N) NA

O) NA

P) NA

Q) SCREWS TO BE INSPECTED IAW 4.3.2 AND 4.3.2.1

R) ACCEPTANCE CRITERIA IAW 4.3.2 AND 4.3.2.1

S) NODESTRUCTIVE TESTING AND ACCEPTANCE CRITERIA SHALL BE IAW 4.3.3

T) MECHANICAL TEST ARE TO BE DONE AFTER FINAL HEAT TREATMENT

U) IAW 5.1

V) -BB) NA

Certification Requirements:

Provide written verification that the chemical and mechanical properties have been determined and are acceptable as follows.

a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Test reports for loose MIL-DTL-1222, K-Monel (QQ-N-286), fasteners and for all assemblies which contain MIL-DTL-1222, K-Monel fasteners, shall include a certification statement describing the forming process used to manufacture the fasteners (i.e. hot headed with cold rolled threads, hot headed with machined threads, etc.), the heat treatments performed, and the order in which these actions were performed(i.e. fasteners manufactured and then solution annealed and age hardened, etc.). This action is required to ensure compliance with MIL-DTL-1222, paragraph 3.3.4, which requires fasteners with formed heads (i.e., hot headed, cold headed, etc.) and rolled threads to be solution annealed and age hardened after the manufacturing process.

(e) Certification for QQ-N-286 Rev G materials shall show that slow strain rate tensile (SSRT) test of “start material” has been accomplished per QQ-N-286 Rev G requirements.

(f) Where headed fastener specification require a yield strength test AND a wedge tensile test, a separate (new, untested) fastener is required for each of the two test methods, and both of these test shall be reported.

FOB: Destination

MILSTRIP: N421587279B196

NET AMT

N421587279B197

CAP SCREW, HEX HEAD, ONE AND ONE QUARTER INCHES, 7-UNC-2A X FOUR AND ONE HALF INCES LONGE, MONEL, QQ-N-281D, MIL-S-1222J

ORDERING DATA

A) GENERAL SPECIFICATIONS FOR STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATION WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; MIL-DTL-1222J; 08 DECEMBER 2000 B) CAP SCREW, HEX HEAD, ONE AND ONE QUARTER INCHES, 7-UNC-2A X FOUR AND ONE HALF INCES LONGE, , TYPE I, QQ-N-281, ALLOY TYPE; NICKEL ALLOY GRADE 400 AS FORMED OR STRESS RELIEVED, UNCOATED

C) LATEST REVISION

D) NA

E) NA

F-J) NA

K) LOCKING ELEMENT NOT REQUIRED

L) AS SPECIFIED

NOTE: WHERE HEADED FASTENERS SPECIFICATIONS REQUIRE A YIELD STRENGTH TEST AND A WEDGE TENSILE TEST, A SEPARAATE (NEW, UNTESTED) FASTENER IS REQUIRED FOR EACH OF THE TWO METHODS, AND BOTH OF THESE TESTS SHALL BE REPORTED.

N) NA

O) NA

P) NA

Q) SCREWS TO BE INSPECTED IAW 4.3.2 AND 4.3.2.1

R) ACCEPTANCE CRITERIA IAW 4.3.2 AND 4.3.2.1

S) NODESTRUCTIVE TESTING AND ACCEPTANCE CRITERIA SHALL BE IAW 4.3.3

T) MECHANICAL TEST ARE TO BE DONE AFTER FINAL HEAT TREATMENT

U) IAW 5.1

V) -BB) NA

Certification Requirements:

Provide written verification that the chemical and mechanical properties have been determined and are acceptable as follows.

a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Test reports for loose MIL-DTL-1222, K-Monel (QQ-N-286), fasteners and for all assemblies which contain MIL-DTL-1222, K-Monel fasteners, shall include a certification statement describing the forming process used to manufacture the fasteners (i.e. hot headed with cold rolled threads, hot headed with machined threads, etc.), the heat treatments performed, and the order in which these actions were performed(i.e. fasteners manufactured and then solution annealed and age hardened, etc.). This action is required to ensure compliance with MIL-DTL-1222, paragraph 3.3.4, which requires fasteners with formed heads (i.e., hot headed, cold headed, etc.) and rolled threads to be solution annealed and age hardened after the manufacturing process.

(e) Certification for QQ-N-286 Rev G materials shall show that slow strain rate tensile (SSRT) test of “start material” has been accomplished per QQ-N-286 Rev G requirements.

(f) Where headed fastener specification require a yield strength test AND a wedge tensile test, a separate (new, untested) fastener is required for each of the two test methods, and both of these test shall be reported.

FOB: Destination

MILSTRIP: N421587279B197

NET AMT

N421587279B198

CAP SREW HEX HEAD, ONE AND ONE EIGHTS INCHES, 7-UNC-2A X THREE AND THREE QUARTERS INCHES LONG, MONEL, QQ-N-281D, MIL-S-1222J

ORDERING DATA

A) GENERAL SPECIFICATIONS FOR STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATION WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; MIL-DTL-1222J; 08 DECEMBER 2000 B) CAP SREW HEX HEAD, ONE AND ONE EIGHTS INCHES 7-UNC-2A X THREE AND THREE QUARTERS INCHES LONG, TYPE I, QQ-N-281, ALLOY TYPE; NICKEL ALLOY GRADE 400, AS FORMED OR STRESS RELIED, UNCOATED.

C) LATEST REVISION

D) NA

E) NA

F-J) NA

K) LOCKING ELEMENT NOT REQUIRED

L) AS SPECIFIED

NOTE: WHERE HEADED FASTENERS SPECIFICATIONS REQUIRE A YIELD STRENGTH TEST AND A WEDGE TENSILE TEST, A SEPARAATE (NEW, UNTESTED) FASTENER IS REQUIRED FOR EACH OF THE TWO METHODS, AND BOTH OF THESE TESTS SHALL BE REPORTED.

N) NA

O) NA

P) NA

Q) SCREWS TO BE INSPECTED IAW 4.3.2 AND 4.3.2.1

R) ACCEPTANCE CRITERIA IAW 4.3.2 AND 4.3.2.1

S) NODESTRUCTIVE TESTING AND ACCEPTANCE CRITERIA SHALL BE IAW 4.3.3

T) MECHANICAL TEST ARE TO BE DONE AFTER FINAL HEAT TREATMENT

U) IAW 5.1

V) -BB) NA

Certification Requirements:

Provide written verification that the chemical and mechanical properties have been determined and are acceptable as follows.

a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Test reports for loose MIL-DTL-1222, K-Monel (QQ-N-286), fasteners and for all assemblies which contain MIL-DTL-1222, K-Monel fasteners, shall include a certification statement describing the forming process used to manufacture the fasteners (i.e. hot headed with cold rolled threads, hot headed with machined threads, etc.), the heat treatments performed, and the order in which these actions were performed(i.e. fasteners manufactured and then solution annealed and age hardened, etc.). This action is required to ensure compliance with MIL-DTL-1222, paragraph 3.3.4, which requires fasteners with formed heads (i.e., hot headed, cold headed, etc.) and rolled threads to be solution annealed and age hardened after the manufacturing process.

(e) Certification for QQ-N-286 Rev G materials shall show that slow strain rate tensile (SSRT) test of “start material” has been accomplished per QQ-N-286 Rev G requirements.

(f) Where headed fastener specification require a yield strength test AND a wedge tensile test, a separate (new, untested) fastener is required for each of the two test methods, and both of these test shall be reported.

FOB: Destination

MILSTRIP: N421587279B198

NET AMT

N421587279B241

CAP SREW HEX HEAD, ONE AND ONE QUARTER INCHES, 7-UNC-3A X FIVE AND ONE HALF INCHES LONG, K MONEL, QQ-N-286G, MIL-S-1222J

ORDERING DATA

A) GENERAL SPECIFICATIONS FOR STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATION WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; MIL-DTL-1222J; 08 DECEMBER 2000 B) CAP SREW HEX HEAD, ONE AND ONE QUARTER INCHES, 7-UNC-3A X FIVE AND ONE HALF INCHES LONG, TYPEI ALLOY TYPE; Grade 500, annealed and age hardened.

C) LATEST REVISION

D) NA

E) NA

F-J) NA

K) LOCKING ELEMENT NOT REQUIRED

L) AS SPECIFIED

N) NA

O) NA

P) NA

Q) SCREWS TO BE INSPECTED IAW 4.3.2 AND 4.3.2.1

R) ACCEPTANCE CRITERIA IAW 4.3.2 AND 4.3.2.1

S) NODESTRUCTIVE TESTING AND ACCEPTANCE CRITERIA SHALL BE IAW 4.3.3

T) MECHANICAL TEST ARE TO BE DONE AFTER FINAL HEAT TREATMENT

U) IAW 5.1

V) -BB) NA

QQ-N-286G

A) NICKEL-COPPER ALUMINUM ALLOY, WROUGHT (UNS N05500); QQ-N-286 G, 07 DECEMBER 2000

B) FORM 2, ANNEALED AND AGED HARDENED, COLD DRAWN

C) LATESTREVISION

D) FORGING SKETCH NOT REQUIRED

E) SIZE REQUIRED TO SUIT MFG. OF FASTENER

F) NOT REQUIRED

G) N/A

H) TOLERANCES ARE TO BE AS SPECIFIED

I) NOT REQUIRED

J) NOT REQUIRED

K. TO SUIT MFG OF FASTENER

L) N/A

M) EDGES AS SPECIFIED

N) TO SUIT MFG OF FASTENERS

O) MARKINGS AS SPECIFIED

P) MECHANICAL TEST REQUIED (NOT FOR RE-FORGING)

Q) N/A

R) SOLUTION ANNEALED AND SSRT IAW 4.3.6.2

S) SSRT LABORATORY SHALL BE AN APPROVED FACILITY

Certification Requirements:

Provide written verification that the chemical and mechanical properties have been determined and are acceptable as follows.

a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Test reports for loose MIL-DTL-1222, K-Monel (QQ-N-286), fasteners and for all assemblies which contain MIL-DTL-1222, K-Monel fasteners, shall include a certification statement describing the forming process used to manufacture the fasteners (i.e. hot headed with cold rolled threads, hot headed with machined threads, etc.), the heat treatments performed, and the order in which these actions were performed(i.e. fasteners manufactured and then solution annealed and age hardened, etc.). This action is required to ensure compliance with MIL-DTL-1222, paragraph 3.3.4, which requires fasteners with formed heads (i.e., hot headed, cold headed, etc.) and rolled threads to be solution annealed and age hardened after the manufacturing process.

(e) Certification for QQ-N-286 Rev G materials shall show that slow strain rate tensile (SSRT) test of “start material” has been accomplished per QQ-N-286 Rev G requirements.

(f) Where headed fastener specification require a yield strength test AND a wedge tensile test, a separate (new, untested) fastener is required for each of the two test methods, and both of these test shall be report FOB: Destination

MILSTRIP: N421587279B241

NET AMT

N421587279B242

CAP SREW HEX HEAD, ONE AND ONE QUARTER INCHES 7 UNC-2A X FIVE AND THREE QUARTERS INCHES LONG, MONEL, QQ-N-281D, MIL-S-1222J

ORDERING DATA

A) GENERAL SPECIFICATIONS FOR STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATION WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; MIL-DTL-1222J; 08 DECEMBER 2000 B) CAP SREW HEX HEAD, ONE AND ONE QUARTER 7 UNC-2A X FIVE AND THREE QUARTER INCHES LONG, TYPE I, QQ-N-281, ALLOY TYPE; NICKLE ALLOY GRADE 400 AS FORMED OR STRESS RELIEVED, UNCOATED.

C) LATEST REVISION

D) NA

E) NA

F-J) NA

K) LOCKING ELEMENT NOT REQUIRED

L) AS SPECIFIED

NOTE: WHERE HEADED FASTENERS SPECIFICATIONS REQUIRE A YIELD STRENGTH TEST AND A WEDGE TENSILE TEST, A SEPARAATE (NEW, UNTESTED) FASTENER IS REQUIRED FOR EACH OF THE TWO METHODS, AND BOTH OF THESE TESTS SHALL BE REPORTED.

N) NA

O) NA

P) NA

Q) SCREWS TO BE INSPECTED IAW 4.3.2 AND 4.3.2.1

R) ACCEPTANCE CRITERIA IAW 4.3.2 AND 4.3.2.1

S) NODESTRUCTIVE TESTING AND ACCEPTANCE CRITERIA SHALL BE IAW 4.3.3

T) MECHANICAL TEST ARE TO BE DONE AFTER FINAL HEAT TREATMENT

U) IAW 5.1

V) -BB) NA

Certification Requirements:

Provide written verification that the chemical and mechanical properties have been determined and are acceptable as follows.

a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Test reports for loose MIL-DTL-1222, K-Monel (QQ-N-286), fasteners and for all assemblies which contain MIL-DTL-1222, K-Monel fasteners, shall include a certification statement describing the forming process used to manufacture the fasteners (i.e. hot headed with cold rolled threads, hot headed with machined threads, etc.), the heat treatments performed, and the order in which these actions were performed(i.e. fasteners manufactured and then solution annealed and age hardened, etc.). This action is required to ensure compliance with MIL-DTL-1222, paragraph 3.3.4, which requires fasteners with formed heads (i.e., hot headed, cold headed, etc.) and rolled threads to be solution annealed and age hardened after the manufacturing process.

(e) Certification for QQ-N-286 Rev G materials shall show that slow strain rate tensile (SSRT) test of “start material” has been accomplished per QQ-N-286 Rev G requirements.

(f) Where headed fastener specification require a yield strength test AND a wedge tensile test, a separate (new, untested) fastener is required for each of the two test methods, and both of these test shall be reported FOB: Destination

MILSTRIP: N421587279B242

NET AMT

N421587279B243

CAP SREW HEX HEAD, ONE AND ONE QUARTER INCHES 7-UNC-3A X FOUR AND THREE QUARTER INCHES LONG, MONEL, QQ-N-281D, MIL-S-1222J

ORDERING DATA

A) GENERAL SPECIFICATIONS FOR STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATION WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; MIL-DTL-1222J; 08 DECEMBER 2000 B) CAP SREW HEX HEAD ONE AND ONE QUARTER INCHES 7-UNC-3A X FOUR AND THREE QUARTER INCHES LONG, Type, QQ-N-N-281D, ALLOY TYPE ,NICKEL ALLOY GRADE 400 AS FORMED OR STRESS RELIEVED, UNCOATED

C) LATEST REVISION

D) NA

E) NA

F-J) NA

K) LOCKING ELEMENT NOT REQUIRED

L) AS SPECIFIED

NOTE: WHERE HEADED FASTENERS SPECIFICATIONS REQUIRE A YIELD STRENGTH TEST AND A WEDGE TENSILE TEST, A SEPARAATE (NEW, UNTESTED) FASTENER IS REQUIRED FOR EACH OF THE TWO METHODS, AND BOTH OF THESE TESTS SHALL BE REPORTED.

N) NA

O) NA

P) NA

Q) SCREWS TO BE INSPECTED IAW 4.3.2 AND 4.3.2.1

R) ACCEPTANCE CRITERIA IAW 4.3.2 AND 4.3.2.1

S) NODESTRUCTIVE TESTING AND ACCEPTANCE CRITERIA SHALL BE IAW 4.3.3

T) MECHANICAL TEST ARE TO BE DONE AFTER FINAL HEAT TREATMENT

U) IAW 5.1

V) -BB) NA

Certification Requirements:

Provide written verification that the chemical and mechanical properties have been determined and are acceptable as follows.

a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Test reports for loose MIL-DTL-1222, K-Monel (QQ-N-286), fasteners and for all assemblies which contain MIL-DTL-1222, K-Monel fasteners, shall include a certification statement describing the forming process used to manufacture the fasteners (i.e. hot headed with cold rolled threads, hot headed with machined threads, etc.), the heat treatments performed, and the order in which these actions were performed(i.e. fasteners manufactured and then solution annealed and age hardened, etc.). This action is required to ensure compliance with MIL-DTL-1222, paragraph 3.3.4, which requires fasteners with formed heads (i.e., hot headed, cold headed, etc.) and rolled threads to be solution annealed and age hardened after the manufacturing process.

(e) Certification for QQ-N-286 Rev G materials shall show that slow strain rate tensile (SSRT) test of “start material” has been accomplished per QQ-N-286 Rev G requirements.

(f) Where headed fastener specification require a yield strength test AND a wedge tensile test, a separate (new, untested) fastener is required for each of the two test methods, and both of these test shall be reported FOB: Destination

MILSTRIP: N421587279B243

NET AMT

N421587279B244

CAP SREW HEX HEAD, ONE AND ONE EIGHTS INCHES 7 UNC-2A X FOUR AND ONE QUARTER INCHES LONG, K MONEL, QQ-N-286G, MIL-S-1222J

ORDERING DATA

A) GENERAL SPECIFICATIONS FOR STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATION WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; MIL-DTL-1222J; 08 DECEMBER 2000 B) CAP SREW HEX HEAD, ONE AND ONE EIGHTS INCHES 7 UNC-2A X FOUR AND ONE QUARTER INCHES LONG, TYPE I, ALLOY TYPE GRADE 500, ANNEALED AND AGE HARDENED

C) LATEST REVISION

D) NA

E) NA

F-J) NA

K) LOCKING ELEMENT NOT REQUIRED

L) AS SPECIFIED

N) NA

O) NA

P) NA

Q) SCREWS TO BE INSPECTED IAW 4.3.2 AND 4.3.2.1

R) ACCEPTANCE CRITERIA IAW 4.3.2 AND 4.3.2.1

S) NODESTRUCTIVE TESTING AND ACCEPTANCE CRITERIA SHALL BE IAW 4.3.3

T) MECHANICAL TEST ARE TO BE DONE AFTER FINAL HEAT TREATMENT

U) IAW 5.1

V) -BB) NA

QQ-N-286G

A) NICKEL-COPPER ALUMINUM ALLOY, WROUGHT (uns N05500); QQ-N-286 G, 07 DECEMBER 2000

B) FORM 2, ANNEALED AND AGED HARDENED, COLD DRAWN

C) LATESTREVISION

D) FORGING SKETCH NOT REQUIRED

E) SIZE REQUIRED TO SUIT MFG. OF FASTENER

F) NOT REQUIRED

G) N/A

H) TOLERANCES ARE TO BE AS SPECIFIED

I) NOT REQUIRED

J) NOT REQUIRED

K. TO SUIT MFG OF FASTENER

L) N/A

M) EDGES AS SPECIFIED

N) TO SUIT MFG OF FASTENERS

O) MARKINGS AS SPECIFIED

P) MECHANICAL TEST REQUIED (NOT FOR RE-FORGING)

Q) N/A

R) SOLUTION ANNEALED AND SSRT IAW 4.3.6.2

S) SSRT LABORATORY SHALL BE AN APPROVED FACILITY

Certification Requirements:

Provide written verification that the chemical and mechanical properties have been determined and are acceptable as follows.

a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Test reports for loose MIL-DTL-1222, K-Monel (QQ-N-286), fasteners and for all assemblies which contain MIL-DTL-1222, K-Monel fasteners, shall include a certification statement describing the forming process used to manufacture the fasteners (i.e. hot headed with cold rolled threads, hot headed with machined threads, etc.), the heat treatments performed, and the order in which these actions were performed(i.e. fasteners manufactured and then solution annealed and age hardened, etc.). This action is required to ensure compliance with MIL-DTL-1222, paragraph 3.3.4, which requires fasteners with formed heads (i.e., hot headed, cold headed, etc.) and rolled threads to be solution annealed and age hardened after the manufacturing process.

(e) Certification for QQ-N-286 Rev G materials shall show that slow strain rate tensile (SSRT) test of “start material” has been accomplished per QQ-N-286 Rev G requirements.

(f) Where headed fastener specification require a yield strength test AND a wedge tensile test, a separate (new, untested) fastener is required for each of the two test methods, and both of these test shall be reported FOB: Destination

MILSTRIP: N421587279B244

NET AMT

N421587279B245

CAP SREW HEX HEAD, ONE AND ONE EIGHTS INCEHS 7 UNC-2A X THREE AND THREE QUARTERS INCHES LONG, MONEL, QQ-N-281D, MIL-S-1222J

ORDERING DATA

A) GENERAL SPECIFICATIONS FOR STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATION WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; MIL-DTL-1222J; 08 DECEMBER 2000 B) CAP SREW HEX HEAD, ONE AND ONE EIGHTS INCEHS 7 UNC-2A X THREE AND THREE QUARTERS INCHES LONG, TYPE I, QQ-N-281, ALLOY TYPE; NECKEL ALLOY GRADE 400 AS FORMED OR STRESS RELIEVED, UNCOATED

C) LATEST REVISION

D) NA

E) NA

F-J) NA

K) LOCKING ELEMENT NOT REQUIRED

L) AS SPECIFIED

NOTE: WHERE HEADED FASTENERS SPECIFICATIONS REQUIRE A YIELD STRENGTH TEST AND A WEDGE TENSILE TEST, A SEPARAATE (NEW, UNTESTED) FASTENER IS REQUIRED FOR EACH OF THE TWO METHODS, AND BOTH OF THESE TESTS SHALL BE REPORTED.

N) NA

O) NA

P)…