Fuel_Bags-_Item_Description_-3658.docx

NSN: 5430-01-237-3658

LINER, BERM, TANK, FABRICATION

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB

AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR

SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ006: QUALITY CONFORMANCE INSPECTION REQUIREMENTS

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

MILITARY SPECIFICATION MIL-B-53081

P/N M53081-1

USED IN INLAND PETROLEUM DISTRIBUTION SYSTEM, 3K FABRIC BAG.

SPEC CHG #001 AS FOLLOWS:

HOSE LENGTHS AS IDENTIFIED IN PARA. 3.8 OF MIL-B-53081 WILL BE 10 FEET

I/L/O 20 FEET.

HANDLES REPLACE PARAGRAPH 3.6 OF MIL-B-53081 WITH NOTED PARAGRAPH 3.6 OF

LETTER CHANGE.

MIL-B-53081 NOTES:

FIGURE 1 OF MIL-B-53081 SHOULD NOT BE USED TO LOCATE THE HANDLES,

DIMENSION "B" IS FOR THE DRAIN LOCATION.

DISREGARD CURE DATE REQUIREMENT IN ABOVE TABLE. USE MFG'D DATE.

EXCEPTIONS TO MIL-B-53081(ME) PER (81349) MIL-B-53081 IDENTIFIED AS

LETTER CHANGE TO MIL-B-53081, DATED 17 JAN 1995:

4.7.2.2 SAMPLING: MIL-STD-105 CANCELLED USE MIL-STD-1916 OR ANSI/ASQ

Z1.4

5.2.7 BERM LINER: CALLS FOR DUSTING USING TALC OR ANTI-STICKING

COMPOUND. EXCEPTION TO DUSTING IS ACCEPTABLE IF THE MATERIAL USED IS

SPECIFICALLY DESIGNED NOT TO BLOCK AND EXCEEDS THE REQUIREMENTS

SPECIFIED PER MIL-B-53081.

MARKINGS: STENCILING IS ACCEPTABLE IN ACCORDANCE WITH IDENTIFICATION

MARKING PARAGRAPH 3.10 OF MIL-B-53081. THE BERM LINER SHALL BE

PERMANENTLY MARKED IN ACCORDANCE WITH MIL-STD-130 AND APPLIED DIRECTLY

TO THE BERM LINER SURFACE. THE FOLLOWING INFORMATION SHALL BE STENCILED,

USING 0.50 INCH (MINIMUM) LETTERS.

REFERENCE: IDENTIFICATION LABEL INFORMATION PER PARAGRAPH 3.10,

MIL-B-53081.

QAP EQ003 APPLIES

CRITICAL ITEM - SOURCE INSPECTION REQUIRED.

TYPE I 144 MONTHS (12 YEAR) SHELF LIFE ITEM:

MATERIAL FURNISHED UNDER THIS CONTRACT/ORDER SHALL

HAVE AT LEAST 85% OF THE SHELF LIFE

REMAINING AT TIME OF DELIVERY. SHELF LIFE

MARKINGS (CURE AND EXPIRATION DATES) SHALL

BE IN ACCORDANCE WITH MIL-STD-129, LATEST

REVISION, AND SHALL BE SHOWN IN

CALENDAR QUARTER AND YEAR. EXPIRATION DATE SHALL

BE 12 YEARS FROM CURE DATE.

THE DRAWING(S) LISTED BELOW ARE AVAILABLE AT

DLA DURING *OPEN SOLICITATION ONLY*.

TO RECEIVE A COPY OF THE DRAWING(S),

FOR EBS SOLICITATIONS USE URL

HTTPS://WWW.DIBBS.BSM.DLA.MIL/RFQ/

CRITICAL APPLICATION ITEM

IAW BASIC SPEC NR MIL-B-53081 NOT 1

REVISION NR DTD 09/25/1998

PART PIECE NUMBER: M53081-1

IAW REFERENCE DRAWING NR 81349 MIL-B-53081

REVISION NR DTD 09/14/2006

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 MIL-B-53081

REVISION NR DTD 09/25/1998

PART PIECE NUMBER:

IAW REFERENCE QAP 14153 QAP-EQ003

REVISION NR B DTD 05/16/2013

PART PIECE NUMBER:

IAW REFERENCE STD NR MIL-STD-129R

REVISION NR R DTD 02/18/2014

PART PIECE NUMBER:

PKGING DATA-QUP:001

SHALL BE PACKAGED IN ACCORDANCE WITH HAZARDOUS

MATERIALS PACKAGING REQUIREMENTS.

PACKAGING: PACKAGING FOR HAZARDOUS MATERIALS

SHALL COMPLY WITH APPLICABLE REGULATIONS, I.E.,

TITLE 49 CODE OF FEDERAL REGULATIONS,

INTERNATIONAL CIVIL AVIATION ORGANIZATION (ICAO)

TECHNICAL INSTUCTIONS (EXCLUDING PARAGRAPH 1.4

OF CHAPTERS 1 AND 3), AND INTERNATIONAL MARITIME

DANGEROUS GOODS CODE (IMDG). BOTH ICAO AND IMDG

COMPLY WITH UNITED NATIONS (UN) RECOMMENDATIONS

ON TRANSPORT OF DANGEROUS GOODS. WHEN A);

CONTRACT/ORDER FOR HAZARDOUS MATERIALS REQUIRES

SHIPMENT THROUGH A MILITARY AERIAL PORT FOR

TRANSPORT VIA MILITARY AIRCRAFT, PACKAGING SHALL

COMPLY WITH DLAI 4145.3, PREPARING HAZARDOUS

MATERIALS FOR MILITARY AIR SHIPMENT.

LABELING AND MARKING: ALL INTERIOR AND EXTERIOR

CONTAINERS SHALL BE LABELED AND MARKED AS

SPECIFIED IN THE REFERENCED PRODUCT

SPECIFICATION, AND/OR AS SPECIFIED IN SECTION D

OF THE CONTRACT OR ORDER. IN ADDITION, ALL

LABELING AND MARKING SHALL COMPLY WITH THE

REQUIREMENTS OF MIL-STD-129, 49 CFR, 29 CFR,

AND, AS APPLICABLE, ICAO TECHNICAL INSTRUCTIONS,

IMDG ANNEX 1, AND/OR DLAI 4145.3.

CERTIFICATION: ALL PACKAGING PERFORMANCE TEST

REQUIREMENTS SHALL BE SUPPORTED BY CERTIFICATES

AND REPORTS ATTESTING TO DATE OF TESTING AND

DATA RESULTS OBTAINED FROM TESTING. THE

CONTRACTOR'S SIGNED CERTIFICATION THAT PACKAGE

CONFIGURATION MEETS 49 CFR, AND, AS APPLICABLE,

ICAO, IMDG AND/OR DLAI 4145.3 REQUIREMENTS,

SHALL BE INCLUDED ON THE DD FORM 250 (MATERIAL

INSPECTION AND RECEIVING REPORT), OR ANY

SUITABLE ALTERNATE COMMERCIAL PACKING LIST. ALL

CERTIFICATES/REPORTS SHALL BE AVAILABLE FOR

INSPECTION BY AUTHORIZED U. S. GOVERNMENT

REPRESENTATIVES FOR A PERIOD OF NOT LESS THAN 3

YEARS FROM THE DATE OF SHIPMENT.

IF THE MATERIAL IS NOT CONSIDERED HAZARDOUS,

IN ACCORDANCE WITH FED-STD-313, THE MATERIAL

SHALL BE COMMERCIALLY PACKAGED IN ACCORDANCE

WITH "ASTM D3951."

Markings Paragraph When ASTM D3951, Commercial Packaging is specified, the following apply:

•,,All Section “D” Packaging and Marking Clauses take precedence over

ASTM D3951.

•,,In addition to requirements in MIL-STD-129, when Commercial Packaging is used, the Method of Preservation for all MIL-STD-129 marking and labeling shall be “CP” Commercial Pack.

•,,The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) as specified in the contract take precedence over QUP in ASTM D3951.