Tech_Data_PGC_00333_March_2018.docx

PGC00333 Coveralls, Utility, Type I, Class 1, Shade Blue 3329

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

COVERALLS SHALL BE MADE IN ACCORDANCE WITH NCTRF-CID-55095, DATED JANUARY 31, 2017.

PATTERN DATE: 22 February 2017

STANDARD SAMPLE OF CLOTH, TWILL, POLYESTER AND

COTTON, BLUE SHADE 3329, IS APPLICABLE FOR

SHADE, COLORFASTNESS TO LIGHT, LAUNDERING,

WET/DRY CROCKING, AND PERSPIRATION - PIECE

NO. 09280 APPLIES

Standard sample for button Navy shade Dark Blue 501 is available for shade only.

Additional Information for NCTRF-CID-55095:

Page 4, Paragraph 3.2.2, At end of paragraph add: "The cloth shall be products that are authorized by the certifying activity for listing on the applicable source control drawing, NCTRF Drawing 01-NCTRF-17, before contract award (see 7.5). Unless otherwise specified in the contract the certification sample yardage shall be 5 yards. The cloth shall be certified through inspection and examination for the cloth salient characteristics specified in this document when tested as specified in 3.2.3, 3.2.3.1 and Table I. The certification inspection shall be unacceptable if the requirements are not met.".

Page 4, Table I, Row 2, Delete: "7.0" and "8.0" from Type II, Class 1, Color C requirements and replace with: "See drawing 01-NCTRF-17"

Page 5 and 6, Delete Flame Resistance Row 10 entire block and Flame Resistance Row 1 entire block and replace with

Flame Resistance, Initial After Flame, seconds (maximum) After Glow, seconds (maximum) Char Length, inches (maximum)

2.0

2.0

5.0

2.0

25.0

5.0

Flame Resistance, After 25 home launderings After Flame, seconds (maximum) After Glow, seconds (maximum) Char Length, inches (maximum) AATCC-135, 1, V, Ai & ASTM D6413

N/A

2.0

2.0

5.0

2.0

25.0

5.0

Page 17, Paragraph 7.5, At end of paragraph, add new entry:

"f. When certification is required; name and address of certification activity (see 3.1.1 and 4.2.1)"

Page 17, Under "MILITARY INTERESTS" delete and substitute:

"Preparing Activity:

Navy-NU

Custodians:

Navy-NU

DLA-CT"

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE FOLLOWING:

LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A PAPER TAG FOR PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE STANDARD BLEACHED SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT PRINTING. THE TAGS SHALL HAVE A HOLE AND SHALL BE ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND READABLE BY SCANNER. THE BAR CODING ELEMENT SHALL BE A 13 DIGIT NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC) ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE INITIAL "UPC" MUST APPEAR BENEATH THE CODE. THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM TO HIGH DENSITY AND SHALL BE LOCATED SO THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND PACKAGED AS SPECIFIED. THE LABEL'S LOCATION SHALL CAUSE NO DAMAGE TO THE ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE (UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII (PRESSURE SENSTIVE LABEL) OF MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE TYPE VIII (TAG, PAPER) OF MIL-DTL-32075.

MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-20" AND REPLACE "MIL-DTL-32075,".

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION FOR A-A-50198A

THREAD, GIMP, COTTON, BUTTONHOLE

STANDARD SAMPLE FOR COLOR FOLIAGE GREEN 504,

IS MIL-C-44436, ROLL #3728, (THE FOLIAGE GREEN

502 AREA PF THE PATTERN) AND REFERENCE

FOR SHADE ONLY.

AATCC 61 COLORFASTNESS TO LAUNDERING, HOME

. AND COMMERCIAL, ACCELERATED.

AATCC 169 WEATHER RESISTANCE OF TEXTILES:

. XENON LAMP EXPOSURE

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO

AMERICAN SOCIETY FOR TESTING AND MATERIALS,

1916 RACE STREET, PHILADELPHIA, PA 19111-1187.

INTERIM CHANGES TO A-A-55126B,

THE FOLLOWING CHANGES ARE FOR ALL CURRENT, PENDING AND FUTURE PROCUREMENTS OF THE SUBJECT DOCUMENT UNTIL SUCH TIME AS THE DOCUMENT IS AMENDED OR REVISED.

PAGE 4. TABLE I, PHYSICAL REQUIREMENTS, CHARACTERISTIC, SHEAR STRENGTH,DELETE LBS/SQ INCH (MIN), ADD SHEAR STRENGTH, LBS/2 SQ INCH (MIN).

PAGE 5 TABLE II, PHYSICAL REQUIREMENTS; CHARACTERISTIC, LENGTH

DIMENSIONAL STABILITY, % (MAX); LOOP, ALL CLASSES DELETE .0; ADD ALL CLASSES 4.0.

PAGE 7, Paragraph 3.10.2, Change the following title of paragraph from: "Fray resistance of Universal Camouflage Shades" and replace with "Fray resistance of Camouflage Prints"

PAGE 14, Paragraph 7.3.4 Change the following title of paragraph from: Fray resistance for Universal Camouflage Shades." and replace with "Fray resistance for Camouflage Prints."

ADDITIONAL INFORMATION FOR MIL-STD-1668:

INTERIM CHANGES TO MIL-STD-1668B ARE AS FOLLOWS:

PAGE III, IN THE FORWARD ADD TO THE BOTTOM OF

THE LIST OF SPECIFICATIONS THAT WILL REFERENCE

THIS STANDARD:"MIL-C-24945 - COVERALLS, FLAME

RESISTANT (COTTON FRONT)"

PAGE 12, TABLE II, CLASSIFICATION OF DEFECTS,

TABLE XIII, LABEL(S) AND SYMBOL(S), DELETE

THE TITLE AND SUBSTITUTE "LABELS/BAR CODE".

AND ADD THE FOLLOWING NEW DEFECTS;

"E. BAR CODE LABEL:

LABEL/TAG

BAR CODE OMITTED OR NOT READABLE BY

SCANNER 1

HUMAN READABLE INTERPRETATION (HRI)

OMITTED OR ILLEGIBLE 1

NOT VISIBLE ON FOLDED, PACKAGED ITEM 1

CAUSES DAMAGE TO THE ITEM 3

ASTM D 3776 MASS PER UNIT AREA (WEIGHT)

. OF WOVEN FABRIC

. 3 OCTOBER 1994.

AATCC 8 CHROMATIC TRANSFERENCE SCALE

AATCC 15 COLORFASTNESS TO PERSPIRATION

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

(Ref. T0795 - May 17, 2006)

ADDITIONAL INFORMATION FOR COMMERCIAL AQL'S:

AQL'S FOR COMMERCIAL ITEM DESCRIPTIONS (CID'S):

VISUAL - GENERAL INSPECTION LEVEL II, AQL - 1.0

DIMENSIONAL - SPECIAL INSPECTION LEVEL S-2, AQL - 2.5

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE USE

OF "SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES", ANSI/ASQC Z1.4

PACKAGING

Case Lot is 30 Coveralls, of one size only, packed in each carton.

As a minimum item shall be packed in a snug fitting fiberboard shipping container conforming to ASTM-D-5118, Type CF, Style RSC, Grade 275, variety SW, Class domestic, with a double wall liner. Any commercial closure method cited in ASTM-D-1974 is acceptable except stapling.

Packaging shall be as per ASTM-D-3951, MIL-STD-129 with change notice 4, MIL-STD-147. Lot numbering shall be in accordance with MIL-STD-129 AND DSCP-4155.3

Packaging examination. The fully packaged end item shall be examined for the defects listed below. The lot size shall be expressed in units of shipping containers. The sample unit shall be one shipping container fully packaged. The Inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5.

Examine Defect

Marking Omitted; incorrect; illegible, of (exterior) improper size, location, sequence & Unit Pack, or method of application.

Materials Any component missing, damaged or not as specified.

Workmanship Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling. Bulged or distorted container.

Contents Number of intermediate containers per shipping container is more or less than required.

Number of items per container is more or less than required.

Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load, fully packaged.

The Inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5.

Examine Defect

Finished Length, width or height exceeds Dimensions specified maximum requirement.

Palleti- Pallet pattern not as specified.

zation Interlocking of loads not as specified. Load not bonded with required straps as specified.

Weight Exceeds maximum load limits.

Marking Omitted; incorrect; illegible;

of improper size, location, sequence or method of appli-cation.

MIL-STD-129R - DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED 18 FEBRUARY 2014

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147E

w/CHANGE 1 23 December 2013

SUPERSEDING

MIL-STD-147E

16 May 2008

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS