Tech_Data_Mechanics_Coverall_PGC_00022.pdf

Coverall, Mechanics, Operational Camouflage Print, Type IV PGC 00022

Size NSN UPC

SML 8415-01-664-3139 718020746968

MED 8415-01-664-3140 718020990200

LARGE 8415-01-664-3142 718020846859

XLG 8415-01-664-3143 718020907406

XXLG 8415-01-664-3145 718020673066

SECTION C- DESCRIPTION/SPECIFICATION

COVERALLS, MECHANIC, Operational Camouflage Pattern

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY

REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL

TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS

FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR

SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE

DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND

NON-MANUFACTURERS)

Coveralls shall be made in accordance with MIL-DTL-32082A dated 16 FEB

PATTERN DATE: AUGUST 14, 2009

Standard Sample for Class 3, Operation Camouflage Pattern (OCP) is available for shade only under roll number 3930.

**Applicable for all Class 3, Operational Camouflage Pattern (OCP) shade evaluations only. Current shade evaluation process remains unchanged for Class 2 Operation Enduring Freedom Camouflage Pattern

(OEF-CP):

Sampling: Notwithstanding any current provisions of the fabric specification, solicitation or contract, the following shade evaluation shall apply. Fabric pieces will be cut by the Contractor from those rolls of fabric selected by the Government Quality Assurance Representative (QAR) in accordance with the table below.

Pieces shall be 24 inches by full width for Operation Camouflage Pattern cloth.

Lot Size No. of rolls to be Sampled 1 to 8 rolls Each roll 9 to 25 rolls 8 rolls 26 to 90 rolls 20 rolls 91 to 160 rolls 32 rolls over 160 rolls 1 out of every 5 rolls

The Government representative shall ensure that each fabric piece is cut in half. Each half piece shall be identified with the roll number from which it was cut. A half piece is sent to Natick for evaluation and shall be no smaller than 24" x 30" for OCP. Each piece shall have identifier tags securely attached and a tally list of all the rolls being evaluated shall be included. All DD1222s shall include the contract number in block 3 and vendor email addresses in Box 4 and/or

17. The remaining pieces shall be retained at the Mill for use by the QAR. The Contractor shall send the pieces to be evaluated for shade along with a completed DD1222 to:

US Army Natick Soldier RD&E Center ATTN: Melanie King/Rachel Matuszek 15 Kansas St Natick, MA 01760 Bldg 5 RM 122 RDNS-SEW-EWC 2 December 2014 SUBJECT: Sampling of Fabric for Shade Evaluation Operational Camouflage Pattern (OCP)

Sampling of Fabric for Shade Evaluation Operational Camouflage Pattern(OCP)

Completed DD1222s shall be emailed in a Microsoft Word document to Natick at the following email addresses:

melanie.a.king14.civ@mail.mil;

rachel.l.matuszek.civ@mail.mil

Shade Uniformity: When Section 3 of the fabric specification contains a specific requirement for uniformity of shade and when the standard sample is referenced for uniformity of shade, the pieces submitted in accordance with sampling procedure above shall also be evaluated for uniformity of shade.

Shade Evaluation: If one or more of the shade pieces submitted are found unacceptable, the entire lot shall be rejected. A lot that was rejected for shade may be screened and all rolls in the lot which were found unacceptable for shade shall be removed before such a lot is resubmitted. Resubmitted lots shall again be subjected to the sampling and shade evaluation prescribed herein. This requirement does not negate the Contractor's responsibility to perform shade evaluation prior to submittal of a lot to the Government. Each roll of fabric acceptable for shade from which a shade piece has been removed shall be cut by the Contractor from selvage to selvage so that there will be no evidence of the shade piece cut-out. The portion removed shall not be included in the yardage indicated on the piece ticket. If the Contractor reworks and resubmits rolls originally rejected for shade or finish, it shall not combine the rejected rolls with other lots or with lots rejected for other causes. Such rejected rolls shall be combined to form one resubmitted lot. Each piece shall retain its original piece number, suffixed with an "X". The lot number shall also be suffixed with an "X".

Approval: The Prime Contractor shall not cut the fabric until the fabric has been approved for shade conformance via a DD 1222, or when a lot has failed that it has been accepted under a waiver via a completed DD3440.

**End of Class 3, Operational Camouflage Pattern (OCP) shade evaluation direction.

INTERIM CHANGES FOR MIL-DTL-32082A:

1.2.1 Types, Add Type IV - Operational Camouflage Pattern Comment Suggestion box: line 5: Delete "https://assist.daps.dla.mil/" and replace with "https://assist.dla.mil"

2.2.1 Specifications, standards, and handbooks: Delete in its entirety: "(Copies of these documents are available online at https://assist.daps.dla.mil/guicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111- 5094.)" and replace with:

"(Copies of these documents are available online at https://assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)"

3.4.1 Basic material: Delete in its entirety: "3.4.l Basic material.

The basic cloth shall be a Woodland Camouflage printed cotton/nylon twill cloth conforming to Class 5 ofMlL-DTL-44031 for Type 1, Desert Camouflage printed cotton/nylon twill cloth conforming to Class 3C ofMlL-C-44034 for Type II, and Universal Camouflage printed cotton/nylon twill cloth conforming to Class 3 ofMlL-DTL-44031 for Type III. Use of fabric seconds or ground shade cloth is acceptable for inside the waistband and front side pass thru reinforcement pieces only." and replace with: "3.4.1 Basic material. The basic cloth shall be a printed cotton/nylon twill. Cloth for the Type I coverall shall conform to Class 5 ofMIL-DTL-44031. Cloth for the Type II coverall shall conform to Class 3C of MIL-C-44034. Cloth for the Type III coverall shall conform to Class 3 of MIL-DTL- 44031 and the cloth for the Type N Coverall shall conform to Class 11 ofMIL-DTL-44031. Use of fabric seconds or ground shade cloth is acceptable for inside the waistband and front side pass thru reinforcement pieces only."

3.4.2 Thread: Delete in its entirety: "3.4.2 Thread. The color for Type I shall be Camouflage Green 483, approximating color chip 34094, Type II shall be Khaki P-1, C. A. 66019 and Type III shall be Foliage Green 504." and replace with: "3.4.2 Thread. The color for Type I shall be Camouflage Green 483, Type II shall be Khaki P-1, C. A.

66019, Type III shall be Foliage Green 504 and Type IV shall be Tan 499."

3.4.3 Fastener tape: Delete in its entirety: "3.4.3 Fastener tape. The hook and loop tape conforming to A-A-55126 shall be Camouflage Green 483 for Type I , Tan 380 for Type II or Foliage Green 504 for Type III." and replace with: "3.4.3. Fastener tape. The hook and loop tape conforming to A-A-55126 shall be Camouflage Green 483 for Type I, Tan 380 for Type II, Foliage Green 504 for Type III and Tan 499 for Type

IV."

3.4.6 Zipper thong: Line 3, Delete in its entirety: "The color of the thong shall be Black 357 or Camouflage Green 483 for Type I, Tan 380 for Type II or Foliage Green 504 for Type III." and replace with the following: "The color of the thong shall be Black 357 or Camouflage Green 483 for Type I, Tan 380 for Type II, Foliage Green 504 for Type III and Tan 499 for Type IV"

Section 6 NOTES: Delete in its entirety: "(This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.)" and replace with the following: "(This section contains information of a general or explanatory nature that may be helpful, but is not mandatory or contractually binding.)"

6.5 Subject term (key word) listing: Delete in its entirety: "Cloth, printed Dese1t Camouflage Fastener tape, Hook and loop Universal Camouflage Webbing, Elastic Woodland Camouflage Zipper, Zipper thong" and replace with: "Cloth, printed Desert Camouflage Pattern Fastener tape, Hook and loop Operational Camouflage Pattern (OCP) Universal Camouflage Pattern (UCP) Webbing, Elastic Woodland Camouflage Pattern Zipper, Zipper thong"

Delete in its entirety: "https://assist.daps.dla.mil/": and replace with: "https://assist.dla.mil/"

MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-

20" AND REPLACE "MIL-DTL-32075,".

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION FOR A-A-55634A, 23 MARCH 2004:

SPECIAL NOTE!! ALL SLIDE FASTENERS USED ARE TO BE MEASURED FROM "STOP

TO STOP". RECOMMEND THAT THIS MEASUREMENT BE TAKEN RANDOMLY BEFORE

SLIDE FASTENERS ARE SEWN TO THE ITEMS, COVERALL, OR ANY ITEM REFERRED

TO IN THE SOLICITATION. "THE QAR WILL REJECT ANY SLIDE THAT IS NOT

LAYING FLAT AFTER IT IS SEWN INTO/ONTO AN ITEM." SPECIAL INFO ON

ITEMS THAT UTILIZE SLIDE FASTENERS IS GIVEN BY "ALL USING MILITARY

PERSONNEL".

INTERIM CHANGES TO A-A-55126B,

THE FOLLOWING CHANGES ARE FOR ALL CURRENT, PENDING AND FUTURE

PROCUREMENTS OF THE SUBJECT DOCUMENT UNTIL SUCH TIME AS THE DOCUMENT

IS AMENDED OR REVISED.

PAGE 4. TABLE I, PHYSICAL REQUIREMENTS, CHARACTERISTIC, SHEAR

STRENGTH,DELETE LBS/SQ INCH (MIN), ADD SHEAR STRENGTH, LBS/2 SQ INCH

(MIN).

PAGE 5 TABLE II, PHYSICAL REQUIREMENTS; CHARACTERISTIC, LENGTH

DIMENSIONAL STABILITY, % (MAX); LOOP, ALL CLASSES DELETE .0; ADD ALL

CLASSES 4.0.

PAGE 7, Paragraph 3.10.2, Change the following title of paragraph from: "Fray resistance of Universal Camouflage Shades" and replace with "Fray resistance of Camouflage Prints"

PAGE 14, Paragraph 7.3.4 Change the following title of paragraph from:

Fray resistance for Universal Camouflage Shades." and replace with "Fray resistance for Camouflage Prints."

ADDITIONAL INFORMATION FOR A-A-55243:

PAGE 1, SALIENT CHARACTERISTICS, LINE 2 AFTER

CAMOUFLAGE GREEN 483. ADD INTERIM STANDARD

SAMPLE FOR FOLIAGE GREEN 504 IS MIL-C-44436

ROLL #3729 (THE FOLIAGE GREEN 502 AREA OF THE

PATTERN), AND REFERENCED FOR SHADE ONLY.

FOLIAGE GREEN 504 IS TO BE USED AS SPECIFIED

BY CONTRACT.

ADDITIONAL INFORMATION FOR MIL-C-44031:

STANDARD SAMPLE:

FOR CLASS 1, ROLL NO. CF-2 APPLIES FOR

COLORFASTNESS ONLY. ROLL NO. 3530 APPLIES FOR

SHADE AND APPEARANCE ONLY.

FOR CLASS 2, ROLL NO. 3280 APPLIES FOR

SHADE, APPEARANCE AND COLORFASTNESS.

STANDARD SAMPLE FOR UNIVERSAL CAMOUFLAGE

IS MIL-C-44436, ROLL # 3729 AND IS REFERENCED

FOR SHADE ONLY.

THE MULTICAM® CAMOUFLAGE PATTERN SHALL BE EVALUATED FOR COLOR AS

FOLLOWS:

ALL COLOR EVALUATIONS TO INCLUDE VISUAL, SPECTRAL REFLECTANCE, AND

COLORFASTNESS SHALL BE PERFORMED ON THE SOLID COLOR AREA AND NOT THE

TONAL AREA."THIS CHANGE APPLIES TO ALL PRINTED FABRICS WITH MULTICAM®.

INTERIM CHANGES TO MIL-C-44031D:

PAGE 1,PARAGRAPH 1.2, AFTER "CLASS 2" ADD "CLASS 3 - UNIVERSAL

CAMOUFLAGE PRINTED".

PAGE 4, PARAGRAPH 3.3.3 YARNS: DELETE IN IT'S

ENTIRETY AND SUBSTITUTE THE FOLLOWING: "3.3.3

STATIC DISSIPATION FIBER. THE FIBER SHALL HAVE A

CARBON CORE AND NYLON SHEATH AND SHALL BE 3

DENIER PER FILAMENT, AND 1-1/2 TO 2 INCHES IN

STAPLE LENGTH (SEE 6.21)".

PAGE 4, AFTER PARAGRAPH 3.3.3 ADD THE FOLLOWING:

"3.3.4 YARNS. THE WARP AND FILLING YARN SHALL BE

SINGLES MADE FROM A BLEND OF 50 +- 5 PERCENT

NYLON AND THE REMAINING PERCENTAGE COTTON, BASED

ON THE DRY WEIGHT OF THE DESIZED CLOTH WHEN

TESTED AS SPECIFIED IN 4.4.4. THE YARN FOR THE

CLASS 1 AND 3 CLOTH SHALL CONTAIN 2 PERCENT MINIMUM

STATIC DISSIPATIVE FIBER".

PAGE 4, PARA. 3.4. AT THE BEGINNING OF THE FIRST

SENTENCE, AFTER COLOR. INSERT "FOR TYPES I AND II," AND AT THE END OF

THE PARAGRAPH ADD: "RESIN BONDED PIGMENTS ARE NOT

PERMITTED. WHEN SPECIFIED THE COLOR SHALL BE

UNIVERSAL CAMOUFLAGE.".

PAGE 4, PARA 3.4.2.1, AFTER INSTRUMENTAL MATCH.,

ADD NEW SENTENCE: "AS AN ALTERNATE TO VISUAL

COLOR MATCHING THE FOLLOWING INSTRUMENTAL COLOR

MATCHING REQUIREMENT MAY BE USED."

PAGE 4, PARA 3.4.2.1, LINE 7, DELETE "4.4.4" AND

SUBSTITUTE "4.5.2".

PAGE 6, PARA. 3.7, LINE 2, DELETE THE WORDS

"SINGED AND "MERCERIZED."

PAGE 7, AFTER 3.16 ADD THE FOLLOWING PARAGRAPH:

"3.17 ELECTROSTATIC DECAY. THE FINISHED CLASS 1 AND 3

CLOTH SHALL, WHEN CHARGED TOWARD '+5000' VOLTS AND

-5000 VOLTS, REACH A MINIMUM LEVEL OF '+4000'

AND -4000 VOLTS RESPECTIVELY AND SHALL DISSIPATE

90 PERCENT OF THIS CHARGE IN LESS THAN OR EQUAL

TO 1/2 SECOND. THE AVERAGE WARP RESULTS AND

AVERAGE FILLING RESULTS SHALL MEET THESE

REQUIREMENTS BEFORE AND AFTER FIVE LAUNDERINGS

WHEN TESTED AS SPECIFIED IN 4.4.4".

PARAGRAPH 4.4.3.1. YARD-BY-YARD EXAMINATION

LINE 14, DELETE "30" AND SUBSTITUTE "20"

LINE 15, DELETE "45" AND SUBSTITUTE "30"

LINE 16, DELETE "45" AND SUBSTITUTE "30"

LINE 18, DELETE "45" AND SUBSTITUTE "30"

PAGE 10, PARA . 4.4.3.3, DELETE AND SUBSTITUTE:

SHADE SWATHING EVALUATION REQUIREMENTS

(A) SAMPLING: A 12 INCH BY FULL WIDTH SWATCH

(HEADER) WILL BE CUT BY THE CONTRACTOR FROM

EACH PIECE OR ROLL IN THE LOT. THE HEADER WILL

BE CUT IN HALF TO FORM SET A AND SET B. THE

GOVERNMENT REPRESENTATIVE WILL SELECT SAMPLES IN

ACCORDANCE WITH THE FOLLOWING TABLE:

LOT SIZE (PIECES) PIECES TO BE SAMPLED

1 TO 5 EACH PIECE

6 TO 25 5

26 TO 90 10

91 TO 160 16

OVER 160 PIECES 1 OF EVERY 10 PIECES

(B) THE SWATCHES SHALL BE IDENTIFIED AND

SUBMITTED TO THE DLA TROOP SUPPORT LABORATORY FOR SHADE

EVALUATION. IF ONE OR MORE OF THE SHADE

SWATCHES ARE FOUND UNACCEPTABLE,

THE ENTIRE LOT SHALL BE REJECTED.

ANY END ITEMS MADE FROM THE COMPONENT

LOT SHALL ALSO BE REJECTED. A LOT THAT WAS

REJECTED FOR SHADE SHALL, WITHOUT COST TO

THE GOVERNMENT, BE SCREENED AND ALL DEFECTIVE

PIECES IN THE LOT SHALL BE REMOVED BEFORE SUCH A

LOT IS RESUBMITTED. RESUBMITTED LOTS SHALL AGAIN

BE SUBJECTED TO THE SAMPLING AND SHADE EVALU-

ATION PRESCRIBED HEREIN. THIS REQUIREMENT DOES

NOT NEGATE THE CONTRACTOR'S RESPONSIBILITY

TO PERFORM SHADE EVALUATION PRIOR TO THE

SUBMITTAL OF A LOT TO THE GOVERNMENT.

(C) WHEN SECTION 3 OF THE FABRIC SPECIFICATION

CONTAINS A SPECIFIC REQUIREMENT FOR UNIFORMITY

OF SHADE, THE SWATCHES SUBMITTED IN ACCORDANCE

WITH (A) ABOVE SHALL ALSO BE EVALUATED FOR

UNIFORMITY OF SHADE.

(D) IF THE CONTRACTOR REWORKS AND RESUBMITS

PIECES ORIGINALLY REJECTED FOR SHADE OR FINISH,

THE CONTRACTOR SHALL NOT COMBINE THE REJECTED

PIECES WITH NORMAL PRODUCTION OR WITH LOTS

REJECTED FOR OTHER CAUSES. SUCH PIECES SHALL BE

COMBINED TO FORM ONE RESUBMITTED LOT. EACH PIECE

SHALL RETAIN IT ORIGINAL PIECE NUMBER, SUFFIXED

WITH AN "X". THE LOT NUMBER SHALL ALSO BE

SUFFIXED WITH AN "X'.

(E) SHADE SAMPLING PROCEDURES ARE DETAILED

FURTHER IN DLA TROOP SUPPORT MANUAL, QUALITY REQUIREMENTS,

DPSCM 4155.3, PART 1, WHICH IS INCORPORATED BY

REFERENCE.

THE SWATCHES SHALL BE SUBMITTED TO :

COMMANDER

DLA TESTING CENTER

NAVAL SUPPORT STATION PHILA

700 ROBBINS AVE

BUILDING 5 D

PHILA. PA. 19111-5098

PAGE 4 AND 13, DELETE INSTRUMENTAL MATCH

3.4.2.1 4.5.2".

PAGE 12, ADD THE FOLLOWING TEST METHODS TO TABLE

IV: AFTER SEAM EFFICIENCY UNDER THE APPROPRIATE

COLUMN ADD THE FOLLOWING:

"ELECTROSTATIC DECAY. (CLASS 1 AND 3):

INITIAL 3.17 5931

AFTER FIVE LAUNDERINGS 3.17 AATCC96,VIc, A _1/, AND 5931

_1/ THE LAST WASH CYCLE SHALL BE PERFORMED WITHOUT THE USE OF

DETERGENT. SPECIMENS SHALL BE DRIED AFTER EACH LAUNDERING."

PAGE 21, AFTER 6.20 ADD THE FOLLOWING PARAGRAPH:

"6.21" " STATIC DISSIPATIVE FIBER. THE STATIC

DISSIPATIVE FIBER, ALSO KNOWN AS P-140, IS

AVAILABLE PREMIXED IN BALE FORM IN A 96/4 PERCENT

NYLON/P140 BLEND FROM INVISTA, WILMINGTON, DE."

THE FOLLOWING ADDITIONAL CHANGES ARE APPLICABLE

TO THIS MILITARY DOCUMENT FOR THE PURPOSE

OF INCORPORATING THE UNIVERSAL CAMOUFLAGE

PATTERN:

1. IN APPLICABLE DOCUMENTS SECTION, SECTION 2,

ADD THE FOLLOWING DRAWINGS:

DRAWINGS

U.S. ARMY SOLDIER SYSTEMS CENTER

2-1-2519 - UNIVERSAL CAMOUFLAGE PATTERN,

60-INCHES

2-1-2519-1 - ARPAT CAMOUFLAGE PATTERN DESERT

SAND 500

2-1-2519-2 - ARPAT CAMOUFLAGE PATTERN URBAN

GRAY 501

2-1-2519-3 - ARPAT CAMOUFLAGE PATTERN FOLIAGE

GREEN 502

(COPIES OF DRAWINGS ARE AVAILABLE FROM THE

U.S. ARMY NATICK SOLDIER CENTER, ATTN:

AMSRD-NSC-IP-E, NATICK, MA 01760-5019.)

2. IN SECTION 3, ADD THE FOLLOWING REQUIREMENTS:

COLOR. THE COLOR SHALL BE THE UNIVERSAL

PATTERN. THE CLOTH SHALL BE DYED TO A

GROUND SHADE EITHER MATCHING OR APPROXIMATING

DESERT SAND 500 AND THEN OVERPRINTED WITH

THE CAMOUFLAGE PATTERN BY ROLLER OR SCREEN

PRINTING. WHEN THE GROUND SHADE IS DYED TO MATCH

DESERT SAND 500, THE REMAINING COLORS SHALL BE

OBTAINED BY SUBSEQUENT PRINTING USING TWO

ROLLERS OR ROTARY SCREENS AS APPROPRIATE FOR

THE URBAN GRAY 501 AND FOLIAGE GREEN 502

AREAS OF THE PATTERN. WHEN THE GROUND SHADE

IS DYED TO APPROXIMATE DESERT SAND 500,

ALL THREE COLORS OF THE CAMOUFLAGE PATTERN

SHALL BE OBTAINED BY SUBSEQUENT PRINTING USING

THREE ROLLERS OR ROTARY SCREENS TO MATCH ALL

THREE COLORS. RESIN BONDED PIGMENTS ARE NOT

PERMITTED.

COLORFASTNESS. THE UNIVERSAL CAMOUFLAGE PRINTED

FINISHED CLOTH SHALL SHOW FASTNESS TO LAUNDERING

(AFTER 3 CYCLES), LIGHT (AFTER 40 STANDARD

FADING HOURS OR 170 KILOJOULES), AND

PERSPIRATION EQUAL TO OR BETTER

THAN THE STANDARD SAMPLE OR EQUAL

TO OR BETTER THAN A RATING OF "GOOD") OR

3-4 OF THE AATCC GRAY SCALE FOR COLOR

CHANGE AND COLOR TRANSFER FOR EACH OF THE

PATTERN AREAS, EXCEPT FASTNESS TO LIGHT SHALL BE

EQUAL TO OR BETTER THAN A RATING OF 3 FOR COLOR

CHANGE. THE FINISHED CLOTH SHALL SHOW FASTNESS

TO CROCKING EQUAL TO OR BETTER THAN THE STANDARD

SAMPLE OR SHALL HAVE AN AATCC CHROMATIC

TRANSFERENCE SCALE RATING OF NOT LOWER THAN

3.5 FOR ALL THE PATTERN AREAS. TESTING SHALL

BE AS SPECIFIED IN SECTION 4 OF THIS DOCUMENT.

PATTERN EXECUTION. THE PATTERN ON THE FINISHED

CLOTH SHALL MATCH THE STANDARD SAMPLE WITH

RESPECT TO DESIGN, COLORS AND REGISTRATION OF

THE RESPECTIVE AREAS. EACH PATTERN AREA

SHALL SHOW SOLID COVERAGE. SKITTERINESS

EXCEEDING THAT SHOWN BY THE STANDARD

SAMPLE WILL NOT BE ACCEPTABLE.

THE WARPWISE PATTERN REPEAT OF THE FINISHED

CLOTH SHALL BE 36 +1.25 -2.50 INCHES. WHEN THE

STANDARD SAMPLE IS NOT REFERENCED FOR PATTERN

EXECUTION, A PATTERN DRAWING SHALL BE PROVIDED

AND SHALL MATCH THAT OF DRAWING 2-1-2519

(SEE DRAWINGS & SEE ACQUISITION REQUIREMENTS).

SPECTRAL REFLECTANCE UNIVERSAL CAMOUFLAGE

PATTERN. THE SPECTRAL REFLECTANCE VALUES FOR

EACH COLOR IN THE UNIVERSAL CAMOUFLAGE PRINTED

CLOTH SHALL CONFORM TO THE REQUIREMENTS

SPECIFIED IN TABLE IV WHEN TESTED AS

SPECIFIED IN SECTION 4 OF THIS DOCUMENT.

SPECTRAL REFLECTANCE TABLE FOR UNIVERSAL

CAMOUFLAGE PATTERN.

SPECTRAL REFLECTANCE REQUIREMENTS

REFLECTANCE VALUES (PERCENT)

WAVELENGTH, DESERT URBAN FOLIAGE

NANOMETERS(NM) SAND 500 GRAY 501 GREEN 502

--------MIN.MAX. MIN.MAX. MIN.MAX.

600----------- 28 40 12 26 8 18 620----------- 30 42 14 26 8 18 640----------- 34 48 14 28 8 20 660----------- 38 56 14 30 10 26 680-------------44 60 18 34 10 26

700-------------46 66 24 38 12 28 720------------ 48 68 26 42 16 30 740-------------48 72 30 46 16 30 760-------------50 74 32 48 18 32 780-------------54 76 34 48 18 34 800-------------54 76 34 50 20 36 820-------------54 76 36 54 22 38 840-------------56 78 38 54 24 40 860-------------56 78 40 56 26 42

IN ACQUISITION REQUIREMENTS SECTION ADD:

UNIVERSAL CAMOUFLAGE PATTERN DRAWINGS

IF REQUIRED (SEE PATTERN EXECUTION ABOVE).

3/10/09.

ADDITIONAL INFORMATION FOR MIL-C-44034:

STANDARD SAMPLE FOR CLASS 2 DESERT NIGHT

CAMOUFLAGE IS IDENTIFIED AS ROLL NO. 3171,

REFERENCED FOR SHADE, FINISH APPEARANCE AND

COLORFASTNESS.

STANDARD SAMPLE FOR CLASS 1 DAYTIME DESERT

CAMOUFLAGE IS IDENTIFIED AS ROLL NO. 3264,

REFERENCED FOR SHADE, FINISH APPEARANCE AND

COLORFASTNESS.

STANDARD SAMPLE FOR CLASS 3 DAYTIME DESERT

CAMOUFLAGE IS ROLL NO. 3462, REFERENCED FOR

SHADE, FINISH APPEARANCE AND COLORFASTNESS.

N0TE: WHEN ROLL NO. 3462 IS DEPLETED, ROLL NO.

3477 WILL BE USED AS THE STANDARD SAMPLE.

INTERIM SPEC CHANGES TO MIL-C-44034D:

PAGE 4, AFTER PARAGRAPH 3.3.3 ADD THE FOLLOWING:

"3.3.4 YARNS. THE WARP AND FILLING YARN SHALL BE

SINGLES MADE FROM A BLEND OF 50+- 5 PERCENT

NYLON AND THE REMAINING PERCENTAGE COTTON, BASED

ON THE DRY WEIGHT OF THE DESIZED CLOTH WHEN

TESTED AS SPECIFIED IN 4.4.3.

PAGE 7, PARA 3.8, DELETE "SINGED"

PAGE 7, PARA 3.8, DELETE "MERCERIZED"

EXAMINATION. LINE 14, DELETE "30" AND SUBSTITUTE

"20". LINE 16, DELETE "45" AND SUBSTITUTE "30"

(TWICE). LINE 19, DELETE "45" AND SUBSTITUTE

"30".

PAGE 11, AFTER PARA. 4.4.2.3, ADD:

"EXAMINATION FOR SHADE. AN 8 INCH BY ONE

HALF THE WIDTH SHADE SWATCH SHALL BE CUT BY THE

CONTRACTOR FROM THOSE PIECES SELECTED BY THE

GOVERNMENT IN ACCORDANCE WITH THE FOLLOWING

TABLE:

LOT SIZE (PIECES) SAMPLE SIZE (PIECES)

1 T0 5 EACH PIECE

6 T0 25 5

26 TO 90 10

91 T0 160 15

0VER 160 1 OF 10

THE SWATCHES SHALL BE IDENTIFIED AND SUBMITTED

TO: DLA TESTING CENTER

. NAVAL SUPPORT STATION PHILA

. BUILDING 5 D

. 700 ROBBINS AVE.

. PHILA., PA 19111-5098

FOR SHADE EVALUATION, IF ONE OR

MORE OF THE SHADE SWATCHES SUBMITTED ARE

FOUND UNACCEPTABLE THE ENTIRE LOT SHALL BE

REJECTED. A LOT THAT WAS REJECTED FOR SHADE

SHALL BE SCREENED AND ALL PIECES IN THE LOT

DEFECTIVE FOR SHADE SHALL BE REMOVED BEFORE

SUCH A LOT IS RESUBMITTED. RESUBMITTED LOTS

SHALL BE AGAIN SUBJECTED TO THE SAMPLING

AND SHADE EVALUATION PRESCRIBED HERE IN.

THIS REQUIREMENT DOES NOT NEGATE THE

CONTRACTOR'S RESPONSIBILITY TO PERFORM

SHADE EVALUATION PRIOR TO SUBMITTAL OF A

LOT TO THE GOVERNMENT.

INTERIM SPECIFICATION CHANGES TO MIL-W-5664D:

PARA. 3.3.1 - DELETE IN ITS ENTIRETY AND SUBSTITUTE: "3.3.1 WEAVE

CONSTRUCTION. THE WEAVE FOR ALL TYPES AND CLASSES MAY BE SUPPLIED IN

EITHER SHUTTLE OR SHUTTLELESS LOOM CONSTRUCTION.

PARA. 3.7, SENTENCE 2, DELETE IN ITS ENTIRETY AND SUBSTITUTE "TYPE II

SHALL BE CAMOUFLAGE GREEN 483.

PARA. 4.6.1.1 YARD-BY-YARD EXAMINATION, CONTINUED ON PAGE 6, LINE 2,

DELETE "2.5" AND SUBSTITUTE "1.5.". LINE 3, DELETE "6.5" AND

SUBSTITUTE "4.0"

TABLE II - DELETE THE DEFECT FOR "YARNS (FILLING)" ENTIRELY.

PARA. 4.6.3 - DELETE IN ITS ENTIRETY.

STANDARD SAMPLE FOR FOLIAGE GREEN 504, WEBBING, TEXTILE, ELASTIC, IS

IDENTIFIED AS ROLL NO. 3743, REFERENCED FOR SHADE ONLY.

STANDARD SAMPLE FOR CAMOUFLAGE GREEN 483 IS IDENTIFIED AS ROLL NO.

3523, REFERENCED FOR SHADE ONLY.

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

(Ref. T0795 - May 17, 2006)

ADDITIONAL INFORMATION: FED-STD-751 HAS BEEN

CANCELLED AND REPLACED BY ASTM-D-6193, 4/98

STANDARD PRACTICES FOR STITCHES AND SEAMS.

THIS STANDARD SHOULD BE USED IN PREFERENCE

TO FED-STD-751.

(ref. T0216 - May 18, 2006)

Section D: Inspection Text

PREPARATION FOR DELIVERY

CASE LOT QUANTITY IS 20 COVERALLS PRESERVED AS FOLLOWS:

EACH INDIVIDUAL COVERALL SHALL BE PACKAGED IN A COMMERCIALLY

ACCEPTABLE POLYBAG WITH A REVERSE FLAP CLOSURE.

THE COVERALLS SHALL BE PACKED IN A SNUG FITTING FIBERBOARD SHIPPING

CONTAINER CONFORMING TO STYLE RSC-L, TYPE CF (VARIETY SW) OR SF, CLASS

DOMESTIC, GRADE 275 WITH A DOUBLE WALL LINER.

Packaging shall be as per ASTM-D-3951, MIL-STD-129 and MIL-HDBK-774 apply. Lot numbering shall be in accordance with MIL-STD-129 and DSCP- 4155.3

MIL-STD-147E

w/CHANGE 1 23 December 2013

SUPERSEDING

MIL-STD-147E

16 May 2008

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

MIL-STD-129R - DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED 18 FEBRUARY 2014

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE

MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF

DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING

CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING

CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE

LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST

HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-731 IS HEREBY CANCELLED, NOTICE 2 DATED 12/5/95. ASTM-D-6199

- "STANDARD PRACTICE FOR QUALITY OF WOOD MEMBERS

OF CONTAINERS AND PALLETS" HAS BEEN ADOPTED AS A REPLACEMENT

AS OF 7/29/98.

(ref. T0340 - May 18, 2006)

Packaging examination. The fully packaged end item shall be examined for the defects listed below. The lot size shall be expressed in units of shipping containers. The sample unit shall be one shipping container fully packaged. The Inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5.

Examine Defect

Marking Omitted; incorrect; illegible, of (exterior) improper size, location, sequence & Unit Pack, or method of application.

Materials Any component missing, damaged or not as specified.

Workmanship Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling. Bulged or distorted container.

Contents Number of intermediate containers per shipping container is more or less than required.

Number of items per container is more or less than required.

Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load, fully packaged.

The Inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5.

Examine Defect

Finished Length, width or height exceeds Dimensions specified maximum requirement.

Palleti- Pallet pattern not as specified.

zation Interlocking of loads not as specified. Load not bonded with required straps as specified.

Weight Exceeds maximum load limits.

Marking Omitted; incorrect; illegible;

of improper size, location, sequence or method of appli-cation.

ADDITIONAL INFORMATION FOR MIL-PRF-121: BARRIER MATERIAL,

GREASEPROOFED, WATERPROOFED, FLEXIBLE, 4/30/01.

NO ADDITIONAL INFORMATION FOLLOWS.