Attachment 1 - Statement of Work.pdf

Statement of Work (SOW) Up Cut Saws (5) each.

Background:

a. Requiring Organization Defense Distribution Depot Oklahoma City (DDOO)

b. History Saws are required to replace outdated machines that are maintenance intensive and lack necessary safety equipment required to meet OSHA standards.

c. Purpose of the Statement of Work (SOW):

Purchase new Up Cut Saws five (5) ea.

1. Scope of Work to be Performed by Contractor:

The contractor shall provide all necessary labor and material to construct, deliver and place into operation five (5) new up cut saws. All equipment furnished shall be new from the manufacturer’s most current production. The saws shall be in compliance with all OSHA, federal, state, and local codes and regulations and shall conform to the best quality of materials and workmanship. Accessories not specifically mentioned herein, but necessary to furnish complete systems ready for use, shall also be included and named. All transportation/shipping of the purchased saws shall be provided by the contractor.

The machines must be equivalent to the below listed up cut saws.

1ea 20’ NON-MITER Up Cut Saw.

Saws to be located in: Building Box Factory

Salient Characteristics:

• 230 volt, 3 phase, 60 cycle electrical operation

• 20” diameter carbide tipped blade

• 10hp TEFC arbor drive motor

• 24VDC control for pushbutton operation

• Synchronous belt arbor drive

• VFD soft start and electronic braking of saw motor

• Saw access door with safety switch

• Automatic clamping of material before cutting

• Left side feed

• In-feed table 72” long X 20” wide solid 7 gauge steel with 6” fence rail including machine mounting brackets

• Out-feed table 72” long X 20” wide solid 7 gauge steel with 3” fence rail and ¾’ high tape rule inlaid on front face including machine mounting brackets

• Remote operated Air Operated swing down material stop with control valve and integrated tape measure

• Air Supply prep package with filter, regulator and shut off valve

1ea 24” Miter Capable Up Cut Saw.

Saws to be located in: Building 1 Box Factory

• 24” diameter carbide tipped blade

• 10hp TEFC arbor drive motor

• 24VDC control for pushbutton operation via PLC

• Automatic angle set up programmable for minimum of 12 consecutive angle cuts with minimum of 8 programmable preset buttons for quick access to most used cuts

• Capable of cuts up to 75 degrees from left or right side of 0 degrees

• High resolution step motor and planetary gear drive for power table

PLC controlled

• Synchronous belt arbor drive

• VFD soft start and electronic braking of saw motor

• Saw access door with safety switch

• Automatic clamping of material before cutting

• Left side feed

• In-feed table 120” long X 12” wide galvanized roller conveyor with rollers on 6” center with 3” fence rail including machine mounting brackets

• Out-feed table 72” long X 12” wide galvanized roller conveyor with rollers on 6” center with 3” fence rail including machine mounting brackets

• Remote operated Air Operated swing down material stop with control valve and integrated tape measure

• Air Supply prep package with filter, regulator

• Measurement device on out-feed table

1ea 20” Miter Capable Up Cut Saw

Saw to be located in: Building 506

• 10hp TEFC arbor drive motor

• 24VDC control for pushbutton operation via PLC

• Automatic angle set up programmable for minimum of 12 consecutive angle cuts with minimum of 8 programmable preset buttons for quick access to most used cuts

• Capable of cuts up to 75 degrees from left or right side of 0 degrees

• High resolution step motor and planetary gear drive for power table

PLC controlled

• Synchronous belt arbor drive

• VFD soft start and electronic braking of saw motor

• Saw access door with safety switch

• Automatic clamping of material before cutting

• Left side feed

• In-feed table 96” long X 12” wide galvanized roller conveyor with rollers on 6” center with 3” fence rail including machine mounting brackets

• Out-feed table 72” long X 12” wide galvanized roller conveyor with rollers on 6” center with 3” fence rail including machine mounting brackets

• Remote operated Air Operated swing down material stop with control valve and integrated tape measure

• Air Supply prep package with filter, regulator

1ea 20” Miter Capable Up Cut Saw

Saw to be located in: Building 1022 Reclamation

• 10hp TEFC arbor drive motor

• 24VDC control for pushbutton operation via PLC

• Automatic angle set up programmable for minimum of 12 consecutive angle cuts with minimum of 8 programmable preset buttons for quick access to most used cuts

• Capable of cuts up to 75 degrees from left or right side of 0 degrees

• High resolution step motor and planetary gear drive for power table

PLC controlled

• Synchronous belt arbor drive

• VFD soft start and electronic braking of saw motor

• Saw access door with safety switch

• Automatic clamping of material before cutting

• Left side feed

• In-feed table 96” long X 12” wide galvanized roller conveyor with rollers on 6” center with 3” fence rail including machine mounting brackets

• Out-feed table 48” long X 12” wide galvanized roller conveyor with rollers on 6” center with 3” fence rail including machine mounting brackets

• Remote operated Air Operated swing down material stop with control valve and integrated tape measure

• Air Supply prep package with filter, regulator

1ea 24” Miter Capable Up Cut Saw

Saw to be located in: Building 1 Box Factory

• 24” diameter carbide tipped blade

• 10hp TEFC arbor drive motor

• 24VDC control for pushbutton operation via PLC

• Automatic angle set up programmable for minimum of 12 consecutive angle cuts with minimum of 8 programmable preset buttons for quick access to most used cuts

• Capable of cuts up to 75 degrees from left or right side of 0 degrees

• High resolution step motor and planetary gear drive for power table

PLC controlled

• Synchronous belt arbor drive

• VFD soft start and electronic braking of saw motor

• Saw access door with safety switch

• Automatic clamping of material before cutting

• Left side feed

• In-feed table 120” long X 12” wide galvanized roller conveyor with rollers on 6” center with 3” fence rail including machine mounting brackets

• Out-feed table 180” long X 12” wide galvanized roller conveyor with rollers on 6” center with 3” fence rail including machine mounting brackets

• Remote operated Air Operated swing down material stop with control valve and integrated tape measure

• Air Supply prep package with filter, regulator

Exterior color – Manufacturer’s standard.

Warranty Coverage - Warranty coverage shall be manufacturer’s standard warranty but not less than one year parts and labor.

Operator, Parts and Service Manual(s) and Training – The contractor shall provide with delivery, one (1) complete set of manuals with each machine.

2. Definitions of Terms and Abbreviations:

a. DDOO: Defense Distribution Depot Oklahoma City

b. OSHA: Occupational Safety Health Administration

3. Description of Contractor’s Tasks:

Task 1: Fabricate and Deliver of five (5) each Up Cut Saws to be connected to existing electrical connections, no requirement for additional electrical work is required. Saws to be connected to existing ventilation system, no additional ventilation system modification is required.

Task 2: connections are in place that are required for the installation and operation of the Up Cut Sws prior to scheduling the installation.

Task 3: Install five (5) Up Cut Saws in locations identified in section 1.

Task 4: Provide one (1) 8 hour period of training instruction on the safe operation and preventative maintenance procedures of the installed Up Cut Saws. Training to be conducted at one location to be identified by personnel at the receiving location on the day of delivery and installation.

4. Certification and Acceptance:

Final acceptance of the Up Cut Saws will be performed by personnel at the receiving location.

5. Project Management Approach:

6. Performance and/or Delivery Schedule:

The contractor shall coordinate the delivery to the locations listed below with the POC listed below. Delivery of all 5 completed saws at one time is required.

7. Shipping Location

QTY: 5EA

Defense Logistics Agency

Defense Distribution Depot Oklahoma City, OK 3420 D Ave. BLDG 1, Door 80 Tinker AFB, OK 73145 POC: Tambren Ghoram @ 405-855-3822