SOW_Redacted.pdf

01 Mar 2020

Statement of Work

SERVICE AND MAINTENANCE FOR STRYKER EQUIPMENT

1. Scope: The contractor shall provide all services, labor, parts, materials, and equipment necessary for the service and maintenance for the government-owned hand piece units as listed on Appendix A, "LABEL FOR APPENDIX" at Naval Medical Center San Diego (NMCSD).

Contractor must be a Stryker authorized distributor and technicians must be OEM certified.

Contractor shall service and maintain the equipment within the original equipment manufacturer's (OEM) specifications, in accordance with the US, State, and Local laws and regulations, US Navy regulations, and Joint Commission requirements.

2. Definitions: As used throughout this work statement, the following terms shall have the meaning set forth below:

2.1. Service and maintenance: (a) any modification, adjustment, or replacement of the equipment that corrects a malfunction and effectively brings the equipment into material conformity with the technical specification for that equipment as designated by the original equipment manufacturer (OEM), (b) a procedure or routine that, when observed in the regular, proper operation of the equipment, avoids the material adverse effect of the applicable nonconformity, (c) any measures performed that assure the continued operation of the equipment or returns the equipment to its designed efficiency and capacity, (d) replacement of a piece of equipment on a one-for-one basis in order to provide a substitute of equal or greater value in lieu of a damaged or defective device for compensation, return, or refund of equipment.

2.2. Contracting Officer (KO): A warranted representative of the federal government who has the express authority to enter into, administer, and/or terminate contracts and make related determinations and findings. The KO is the only person authorized to approve changes to any terms, conditions, or requirements of the contract.

2.3. Technical Representative (TR): A Government employee appointed by the KO and responsible for the inspection, evaluation, and acceptance of products and services provided in accordance with the terms and conditions of the contract.

3. Location:

Places of performance shall be:

Main Operating Room Building One, Second Floor Naval Medical Center San Diego 34800 Bob Wilson Drive

San Diego, CA 92134-5000

SPD

Building One, Ground Floor Naval Medical Center San Diego and/or

Biomedical Repair Department Building One, Ground Floor Naval Medical Center San Diego

4. Requirements:

4.1. General Performance Requirements:

4.1.1. The Contractor shall provide equipment maintenance services to include all periodic planned maintenance and unscheduled repairs in accordance with OEM specifications and in compliance with OEM standards, to include repairs necessitated by operator error.

4.1.2. The Contractor may use third party service vendors not limited to the Original Equipment Manufacturer (OEM), however, these vendors must be approved in advance by the KO and TR.

The Contractor must submit a list of any sub-contractors they intend to use as third party service vendors to the KO and TR for approval. Third party service vendors shall not perform any work under this contract prior to such approval.

4.1.3. Ensure that only fully-qualified field engineers and/or technicians who have gone through OEM service schools for the equipment shall be employed in the performance of any and all work performed under this contract. Service personnel shall have sufficient experience to demonstrate proficiency in maintenance of the product. Upon request, Contractor shall provide written assurance of the competency their personnel as well as a list of credentials for approved field service personnel. The KO and/or TR may authenticate the training requirements and request training certificates or credentials from the service vendors at any time.

4.1.4. Test equipment: Test equipment calibration shall be traceable to National Institutes of Standards and Technology (NIST traceable). Any efforts conducted without equipment within the calibration intervals is not performance in accordance with this contract. Upon request by TR, the Contractor and/or service vendors shall provide a copy of the current calibration certification of all test equipment to be used, or which has been used, on NMCSD equipment.

4.1.5. Field Service Reports: Contractor shall furnish a written or electronic vendor supplied Field Service Report (FSR) to the Duty Staff at NMCSD Biomed. All FSR's shall be submitted within 72 hours of completion of service and shall be sent to the following email address:

The contractor or their representative shall complete the FSR to include, at a minimum, the following information:

1. Contractor Name

2. Technician's printed name, telephone number, and signature

3. Date and Time of Arrival

4. ECN (to be provided by Navy) and Serial Number of Equipment

5. Time Expended Repairing/Service: Labor Hours, Rate, Materials

6. Summary of Work Performed and Accepted by End-User, with Government Representative's Printed name and Signature)

Completed Field Service Reports are required prior to acceptance of any invoice. Failure to submit a Field Service Report to NMCSD Biomed can result in delay of payment or rejection of invoice from Government. It is highly recommended that the contractor attach a copy of the Field Service Report to their Wide Area Workflow Invoice in addition to the required submission to NMCSD Biomed in order to expedite invoicing process.

4.2. NMCSD Preventive Maintenance Requirements:

4.2.1. Preventive maintenance shall be performed in a manner which will minimize corrective maintenance and will include but is not limited to: calibration, adjustment, lubrication, updating software for security, safety, or system functionality issues, testing required to maintain a safe environment of care, electrical safety testing, output testing, replacement of batteries and other shelf life components on a scheduled basis (which becomes corrective maintenance if the component fails due to lack of preventive maintenance).

4.2.2. Make repairs to the extent necessary, as determined by inspection tests or disassembly, to ensure a functional system that will efficiently serve its intended purpose and the technical specification for that equipment as designated by the original equipment manufacturer.

4.2.3. Installation of system update changes to resolve specific product reliability problems.

Hardware and software upgrades, defined as those changes that enhance or add product features, are not included.

4.2.4. Preventive Maintenance shall be performed at a minimum of 3 times per year, with the exception for chamber cleaning at 4 times per year, with these scheduled preventive maintenance actions to be coordinated with NMCSD BIOMED after contract award.

4.2.5. Preventive Maintenance Completion: Contractor must insure that 95% or more of all periodic maintenance is performed within 30 days of due date, and that 100% of periodic maintenance is performed within 60 days of the due date.

4.2.6. Equipment in Use: If, for reasons beyond the Contractor’s control, equipment is not made available for maintenance for the entire 30 days before the maintenance due date, and 60 days following due date, the Contractor shall immediately notify the COR.

4.2.7. Equipment Unable to Locate (UTL): If the Contractor is unable to locate an item within the maintenance window specified, the Contractor shall immediately notify the TR. The TR may determine that the property has been disposed of or otherwise inactive or unavailable for use and may adjust the equipment covered under this Statement of Work accordingly.

4.2.8. 100% Preventive Maintenance: Under the circumstances of 4.2.6. and/or 4.2.7., the TR and Contractor shall arrange a means of complying with the requirements for preventive maintenance at no additional cost to the government. Equipment determined missing, lost, or stolen shall be exempt from maintenance.

4.2.9. Uptime Rate: The Contractor shall maintain an overall uptime rate of 95% or better for all equipment covered by this effort. Individual uptime rate for specific equipment, if required, will be as specified on Appendix A.

4.2.10. Uptime Calculation: Uptime is calculated on a rolling 6 month basis. Until the Contractor has at least 6 months of performance history with NMCSD, the uptime shall be calculated cumulatively for the entire duration of the contract.

4.3. NMCSD Corrective Maintenance Requirements:

4.3.1. Correct inoperable condition in a timely manner. Contractor shall respond no later than two (2) hours after telephone notification from BIOMED, Monday-Friday, between the hours of 0800-1600.

4.3.2. Provide only the work necessary to restore the equipment to a properly serviceable/operating condition by adjustments, replacement parts, or minor repairs when it is determined that extensive repairs and parts are not necessary.

4.3.3. Equipment improvements/modifications shall be made only upon BIOMED written approval and direction. This includes software updates to the device. All updates/improvements/modifications performed shall be notated on the field service report or equivalent.

4.3.4. Notify BIOMED immediately upon receipt of OEM safety recall notices or upon receipt of recall notices pertaining to any parts or materials utilized by contractor on the equipment.

4.3.5. Ensure that the original design and functional capabilities shall not be changed, modified, or altered without express written authorization from BIOMED.

4.3.6. Provide suitable OEM recommended repair equipment/tools required for the satisfactory execution of all repairs made.

4.3.7. Furnish OEM approved lubricants and lubricate wear points within the equipment in accordance with OEM guidelines.

4.3.8. Replacement parts shall be covered by the contractor for the duration of the contract.

Extend to the Government all commercial warranties on replacement parts. All replacement parts or supplies utilized shall be new parts or OEM refurbished parts. OEM refurbished parts shall only be accepted upon written request from the contractor to NMCSD Biomed and shall only be utilized/installed upon written approval from NMCSD Biomed to the contractor.

4.4. End-User Requirements:

4.4.1. Service shall be performed on all devices included under contract, regardless of the nature of the cause warranting service/maintenance. Contractor shall not refuse any device under this contract submitted for services. Contractor will perform an official inspection of the device, make an estimate for the services/parts required and the time required for the repairs and an official determination of the cause of the issue, and will provide the required parts and labor in order to restore the equipment to function within the OEM specifications.

4.4.2. Services shall be unlimited for the devices under the contract for the term of the agreement. There shall be no cap or limit placed upon the number of repairs/replacements on any individual unit, or on the facility.

4.4.3. Contractor shall perform preventive maintenance on the (1) Stryker units at least times per year, with a minimum of 6 months between preventive maintenance inspections. Chamber cleaning shall be performed at least 4 times per year. Contractor shall perform preventive maintenance as per the schedule on Appendix A.

4.4.4. Contractor shall keep department personnel informed as to the status/condition of equipment during PM and the repair status/condition when equipment is down or out for repair.

Points of contact for the department are: Biomedical Repair Contracts team at

CATASTROPHIC DAMAGE CLAUSE

4.4.5. If equipment is received and is irreparably damaged, the department requires a written report as to the extensiveness of the damage and the suspected cause or type of maltreatment necessary to cause such damage (e.g., dropped, crushed mechanically, overloaded, etc.). The field service report may serve in this regard if comprehensive.

4.5. Response Time and Labor:

4.5.1. Contractor shall use commercially reasonable efforts to respond by telephone to any report of a malfunction requiring repair within two (2) hours of notification from NMCSD Biomed, Monday through Friday, 0800-1600, Pacific Standard Time. The Contractor shall also provide telephone consulting services, twenty-four (24) hours per day, seven (7) days a week. This consulting service shall be provided to avoid delays in contract service coverage during after-hours and weekend/holiday periods as applicable. Under no circumstances shall the Contractor assume an inquiry, via telephone or any other means, is authorization to provide services not specifically covered by the terms of the contract.

4.5.2. Contractor shall use commercially reasonable efforts to provide on-site support within two

(2) business days from notification by NMCSD Biomed, unless otherwise noted in Section 4.4.

4.5.3. Work required in the performance of this contract shall be performed between the hours of 0800 and 1700, Pacific Standard Time. All compensation for labor from the hours of 0800 to 1700 Pacific Standard Time is provided for in this contract and included in the contract price.

Contractor may be permitted to arrange for the performance outside of these hours via coordination with NMCSD Biomed at no additional-cost-to-the-government.

4.5.4. Any work that would require overtime must be approved, in writing, in advance by the

KO.

5. Travel and Related Expenses: Contractor shall be responsible for its service related trip expenses, including round trip travel, mileage, and overnight living expenses.

6. Shipment: The contractor shall not exceed two (2) business days for shipment of all equipment coming from and/or going to NMCSD Biomed minus exceptions or conditions as previously noted in this Statement of Work. All shipping expenses/costs are provided for in this contract and included in the contract price.

7. Liability:

7.1. The contractor shall not be liable for any loss, damage, or delay due to any cause beyond their reasonable control, including but not limited to fire, explosion, theft, flood, riot, civil commotion, war, malicious acts of mischief, or other circumstances outside of human control.

7.2. NMCSD Employees will not perform maintenance or attempt repairs to equipment covered under this contract while such equipment is under the purview of this contract without express, written concurrence from contractor.

7.3. Insurance: Contractor shall be required to have liability insurance to cover any actions on the part of the Contractor or their sub-contractors which result in injury or death to patients, staff, visitors, or other Contractors. Coverage shall be of at least $500,000 per occurrence.

Additionally, Contractor is required to have property damage liability insurance of at least $500,000. Liability insurance shall meet the requirements set forth in FAR 28.307-2.

8. Utilities, Facilities, and Equipment Access:

8.1. The contractor may use Government utilities (e.g., electrical power, compressed air, water) that are available and required for any service performed under this contract while at Government facilities. The facilities engineer however must approve of any contractor equipment which would connect to these utilities in order to ensure compatibility with NMCSD utilities.

8.2. Any outages required in order to perform services must be approved by NMCSD Facilities Management prior to initiation of work and shall be performed per Facilities' instruction.

Contractor may request Facilities assistance in performing these outages if required.

8.3. Ensure that all use, storage, transport of any materials regulated by OSHA as "hazardous", required for the performance of this contract, is in in compliance with all federal, state, and local regulations. Contractor shall have available MSDS's for any such materials on-site.

8.4. The Contractor shall protect all facilities from damage caused by the Contractor and shall repair, at no additional cost to the Government, all damages caused by the Contractor's activities.

During performance of services, Contractor shall keep the site safe, neat, clean and orderly.

Contractor shall be responsible for all means, methods, techniques, sequences, and procedures of the services

8.5. Access to Equipment: Contractor shall be provided reasonable access to all equipment that is to be serviced and utility outlets required to do the service. The contractor shall be free to start/stop all primary equipment incidentals to the operation of the maintained equipment after permission is received from on-duty personnel responsible for such equipment.

9. Security and Safety Requirements:

9.1. The Contractor is required to submit/complete Naval Base San Diego Base access requirements for access to NMCSD. Contractor shall contact Naval Base San Diego Security Department at 619-556-1653/5336 or at https://www.cnic.navy.mil/regions/cnrsw/installations/navbase_san_diego/om/force_protection/p ass_and_decal.html in order to obtain the necessary clearances to perform this contract. All costs for completing the requirements for access are the responsibility of the contractor.

While waiting for authorized access, contractor shall, at a minimum, contact NMCSD Biomed not later than 1400 on the day prior to a scheduled visit to submit the required information to complete the NMCSD Temporary Security Pass. In case of emergent repairs or service, the contractor shall wait at the NMCSD Main Gate for escort from Biomed personnel.

9.2. Identification, Parking, and Smoking Regulations at NMCSD: Field service personnel shall wear visible photo identification at all times while on the premises of NMCSD. It is the responsibility of the field service personnel to park in the appropriate designated parking areas.

Information on parking is available from NMCSD Security personnel. Smoking is prohibited inside any buildings of NMCSD and is restricted to designated smoking locations only.

Possession of weapons, alcohol, or pharmaceuticals that are not over the counter and not prescribed to the individual/family is prohibited on the premises. Enclosed containers, including tool kits, are subject to search. Violations of regulations may result in citation answerable in the United States (Federal) District Court. Violation of any policy which results in lost time for Contractor or his sub-contractors is the sole responsibility of the Contractor, and shall not be charged to the government. Contractor employees shall demonstrate appropriate behavior and dress at all times.

9.3. Contractor Check-In/Check-Out: Contractor is required to report to Material Management Department, Biomedical Repair Division at Building One (1), Ground Floor, Room GD-18H1 at NMCSD prior to and upon completion of any services or repair work performed.

9.4. General Safety Requirements: The Contractor shall exercise safety precautions as the TR may determine to be reasonably necessary to protect the lives and health of occupants of buildings in which work is being performed. NMCSD will notify the Contractor of any non-compliance with the foregoing conditions and the action(s) to be taken. Service vendors shall, after receipt of such notice, immediately correct the conditions to which attention has been directed. If field service engineer refuses to comply promptly, the TR may issue an order stopping all or any part of the work. Under such circumstances, the KO and hold the service vendor in contract default. Nothing in this section will be construed so as to limit the Contractor or his sub-contractors responsibilities to comply with any existing law, nor to switch jurisdictions.

9.5. Government Right of Refusal: NMCSD reserves the right to reject any of the contractor's personnel and refuse them permission to enter the premises or work on NMCSD equipment. This right may be exercised at any time. The reasons for rejections may include: lack of training and experience, but may also include but not be limited to: behavior, attire, security concerns, immigration status.

10. Compliance with Applicable Laws: Contractor shall be knowledgeable of and comply with all applicable Federal, State, and local laws, regulations, and requirements regarding the conduct of his business. The Contractors personnel shall comply with the DoD Information Assurance Policies applicable. Contractors are required to maintain a Drug Free Workplace, as well as to require any sub-contractor to do the same. Contract shall require wage determinations and comply with applicable Federal and State worker's compensation and occupational disease statutes.

11. Modifications to Contract: Only the KO has the authority to obligate the government, and then only in writing. No modification or instruction from any party shall be construed to authorize the Contractor to take any action for which they expect compensation without written authorization from the KO.

12. Invoicing: All invoicing shall be done in accordance with this statement of work and in accordance with contract. Failure to do so may delay or interfere with payment for services rendered.

13. NMCSD Points of Contact: For all matters concerning performance of this contract, the primary point of contact shall be:

Biomedical Repair Division, Material Management Department

Naval Medical Center San Diego 34800 Bob Wilson Drive San Diego, CA 92134

TEL:

Fax:

Email:

For administrative matters, the contractor may contact the contracting officer as designated in blocks 7.a, 7.b, 8, and 9 as found on the Standard Form 1449 issued for the contract, or may contact:

Material Management Department Naval Medical Center San Diego 34800 Bob Wilson Drive San Diego, CA 92134

TEL:

FAX:

APPENDIX A:

NO. SERIAL

NUMBER

ECN MODEL MFR

1 1903700653 151822 F1 OSCILLATING

SAW PROCARE

STRYKER

2 1908436473 151821 F1 SAG SAW

PROCARE

STRYKER

3 1908020153 151843 F1 RECIPROCATING

SAW PROCARE

STRYKER

4 1924700813 N/A F1 UNIVERSAL

MOTOR PROCARE

STRYKER

5 1718800243 N/A CORDLESS DRIVER

4 PROCARE

STRYKER

6 1718608683 N/A CORDLESS DRIVER

4 PROCARE

STRYKER

7 1618209603 N/A CORDLESS DRIVER

4 PROCARE

STRYKER

8 1618102483 N/A CORDLESS DRIVER

4 PROCARE

STRYKER

9 1718608393 N/A CORDLESS DRIVER

4 PROCARE

STRYKER

10 1718608693 N/A CORDLESS DRIVER

4 PROCARE

STRYKER

11 1718800593 N/A CORDLESS DRIVER

4 PROCARE

STRYKER

12 1618209243 N/A CORDLESS DRIVER

4 PROCARE

STRYKER

13 1618209743 N/A CORDLESS DRIVER

4 PROCARE

STRYKER

14 1605006513 N/A CORDLESS DRIVER

4 PROCARE

STRYKER

15 1616204183 N/A BONE MILL

PROCARE

STRYKER

16 0835218263 133446 BONE MILL

PROCARE

STRYKER

17 1622303693 BONE MILL

PROCARE

STRYKER

18 1706100293 141180 CORE CONSOLE

PROCARE

STRYKER

19 1706100483 141179 CORE CONSOLE

PROCARE

STRYKER

20 1719116153 140900 CORE CONSOLE

PROCARE

STRYKER

21 0917300833 105411 CORE CONSOLE

PROCARE

STRYKER

22 1632324583 140899 CORE CONSOLE

PROCARE

STRYKER

23 1619410293 N/A PI DRIVE MOTOR

STRYKER

24 1514213823 N/A PI DRIVE MOTOR

PROCARE

STRYKER

25 1816412623 N/A PI DRIVE+ MOTOR

PROCARE

STRYKER

26 1714208483 N/A PI DRIVE+ MOTOR

PROCARE

STRYKER

27 1714208493 N/A PI DRIVE+ MOTOR

PROCARE

STRYKER

28 1702519673 N/A PI DRIVE+ MOTOR

PROCARE

STRYKER

29 1816412713 N/A PI DRIVE+ MOTOR

PROCARE

STRYKER

30 1816412603 N/A PI DRIVE+ MOTOR

PROCARE

STRYKER

31 1816412643 N/A PI DRIVE+ MOTOR

PROCARE

STRYKER

32 1717205163 N/A REMB MICRO DRILL

PROCARE

STRYKER

33 1909824333 N/A REMB MICRO DRILL

PROCARE

STRYKER

34 1602203303 N/A REMB MICRO DRILL

PROCARE

STRYKER

35 1602203373 N/A REMB MICRO DRILL

PROCARE

STRYKER

36 1717205153 N/A REMB MICRO DRILL

PROCARE

STRYKER

37 1621812743 N/A REMB MICRO DRILL

PROCARE

STRYKER

38 1602203363 N/A REMB MICRO DRILL

PROCARE

STRYKER

39 1909824343 N/A REMB MICRO DRILL

PROCARE

STRYKER

40 1602601393 134046 REMB OSCILLATING

SAW PROCARE

STRYKER

41 1622207083 135514 REMB OSCILLATING

SAW PROCARE

STRYKER

42 1720200973 140930 REMB OSCILLATING

SAW PROCARE

STRYKER

43 1714506413 141635 REMB OSCILLATING

SAW PROCARE

STRYKER

44 1714404123 141634 REMB OSCILLATING

SAW PROCARE

STRYKER

45 1720201093 140929 REMB OSCILLATING

SAW PROCARE

46 1602601383 134047 REMB OSCILLATING

STRYKER

47 1602601243 134048 REMB OSCILLATING

SAW PROCARE

STRYKER

48 1909342473 1511871 REMB OSCILLATING

SAW PROCARE

STRYKER

49 1909342483 151870 REMB OSCILLATING

SAW PROCARE

STRYKER

50 1720303593 141636 REMB SAGITTAL

SAW PROCARE

STRYKER

51 1706300183 141192 REMB SAGITTAL

SAW PROCARE

STRYKER

52 1831207503 151880 REMB SAGITTAL

SAW PROCARE

STRYKER

53 1601508133 133980 REMB SAGITTAL

SAW PROCARE

STRYKER

54 1720303583 141637 REMB SAGITTAL

SAW PROCARE

STRYKER

55 1706300273 141191 REMB SAGITTAL

SAW PROCARE

STRYKER

56 1601508253 133981 REMB SAGITTAL

SAW PROCARE

STRYKER

57 1601508113 133979 REMB SAGITTAL

SAW PROCARE

STRYKER

58 1622208123 135513 REMB SAGITTAL

SAW PROCARE

STRYKER

59 1909513493 151879 REMB SAGITTAL

SAW PROCARE

STRYKER

60 1908727113 151881 REMB RECIP SAW

PROCARE

STRYKER

61 1720302303 141632 REMB RECIP SAW

PROCARE

STRYKER

62 1605502453 134109 REMB RECIP SAW

PROCARE

STRYKER

63 1720302493 140924 REMB RECIP SAW

PROCARE

STRYKER

64 1720302603 140923 REMB RECIP SAW

PROCARE

STRYKER

65 1720302263 141633 REMB RECIP SAW

PROCARE

STRYKER

67 1622205253 135512 REMB RECIP SAW

PROCARE

STRYKER

68 1605502423 134111 REMB RECIP SAW

PROCARE

STRYKER

69 1605502443 134110 REMB RECIP SAW

70 1908726983 151882 REMB RECIP SAW

STRYKER

71 1535110053 N/A REMB U- DRIVER

PROCARE

STRYKER

72 1616810753 N/A REMB U- DRIVER

PROCARE

STRYKER

73 1535109833 N/A REMB U- DRIVER

PROCARE

STRYKER

74 1601110243 N/A REMB U- DRIVER

PROCARE

STRYKER

75 1710800893 141346 SYSTEM 7 DUAL

TRIGGER PROCARE

STRYKER

76 1305106383 N/A SYSTEM 7 DUAL

TRIGGER PROCARE

STRYKER

77 1706608433 141247 SYSTEM 7 DUAL

TRIGGER PROCARE

STRYKER

78 1307402333 N/A SYSTEM 7 DUAL

TRIGGER PROCARE

STRYKER

79 1307402543 N/A SYSTEM 7 DUAL

TRIGGER PROCARE

STRYKER

80 1619015883 135517 SYSTEM 7 DUAL

TRIGGER PROCARE

STRYKER

81 1307402213 N/A SYSTEM 7 DUAL

TRIGGER PROCARE

STRYKER

82 1619015843 135518 SYSTEM 7 DUAL

TRIGGER PROCARE

STRYKER

83 1721319803 141248 SYSTEM 7 RECIP

SAW PROCARE

STRYKER

84 1721319743 141249 SYSTEM 7 RECIP

SAW PROCARE

STRYKER

85 1301612543 123125 SYSTEM 7 RECIP

SAW PROCARE

STRYKER

86 FEB 123126 SYSTEM 7 RECIP

SAW PROCARE

STRYKER

87 1307901263 123127 SYSTEM 7 RECIP

SAW PROCARE

STRYKER

89 1301612533 123128 SYSTEM 7 RECIP

SAW PROCARE

STRYKER

90 1620802973 135540 SYSTEM 7 RECIP

SAW PROCARE

STRYKER

91 1620802593 135539 SYSTEM 7 RECIP

SAW PROCARE

STRYKER

92 1614119043 135314 SYSTEM 7 STURNUM

SAW PROCARE

STRYKER

93 1614119033 135315 SYSTEM 7 STERNUM

94 1307900823 N/A SYSTEM 7 SAGITTAL

STRYKER

95 1707409543 141195 SYSTEM 7 SAGITTAL

SAW PROCARE

STRYKER

96 1307900733 N/A SYSTEM 7 SAGITTAL

SAW PROCARE

STRYKER

97 1307900813 N/A SYSTEM 7 SAGITTAL

SAW PROCARE

STRYKER

98 1620209183 135529 SYSTEM 7 SAGITTAL

SAW PROCARE

STRYKER

99 1620209123 135530 SYSTEM 7 SAGITTAL

SAW PROCARE

STRYKER

100 1307900743 N/A SYSTEM 7 SAGITTAL

SAW PROCARE

STRYKER

101 1707512543 141194 SYSTEM 7 SAGITTAL

SAW PROCARE

STRYKER

102 1620806733 141188

SYSTEM 7

PRECISION SAW

PROCARE

STRYKER

103 1306800933 N/A SYSTEM 7

PRECISION SAW

PROCARE

STRYKER

104 1306800913 N/A SYSTEM 7

PRECISION SAW

PROCARE

STRYKER

105 1615306243 135515 SYSTEM 7

PRECISION SAW

PROCARE

STRYKER

106 1306800903 N/A SYSTEM 7

PRECISION SAW

PROCARE

STRYKER

107 1306800943 N/A SYSTEM 7

PRECISION SAW

PROCARE

STRYKER

108 1620806773 141189 SYSTEM 7

PRECISION SAW

PROCARE

STRYKER

109 1615305593 135516 SYSTEM 7

PRECISION SAW

PROCARE

STRYKER

110 1909404643 N/A SYSTEM 8 DUAL

TRIGGER PROCARE

STRYKER

111 1908608863 N/A SYSTEM 8 DUAL

TRIGGER PROCARE

STRYKER

112 1908608953 N/A SYSTEM 8 DUAL

TRIGGER PROCARE

113 1910531413 152008 SYSTEM 8 RECIP

STRYKER

114 1910531743 152006 SYSTEM 8 RECIP

SAW PROCARE

STRYKER

115 1910531533 152007 SYSTEM 8 RECIP

SAW PROCARE

STRYKER

116 1909509473 151977 SYSTEM 8 SAGITTAL

SAW PROCARE

STRYKER

117 1909509343 151978 SYSTEM 8 SAGITTAL

SAW PROCARE

STRYKER

118 1909509543 151976 SYSTEM 8 SAGITTAL

SAW PROCARE

STRYKER

119 1232500503 N/A FLYTE BATTERY

POWER LIGHTED

HELMET PROCARE

STRYKER

120 1514213623 N/A FLYTE BATTERY

POWER LIGHTED

HELMET PROCARE

STRYKER

121 1409802323 N/A FLYTE BATTERY

POWER LIGHTED

HELME

STRYKER

122 1512708833 N/A FLYTE CHARGER

PROCARE

STRYKER

123 1922834993 N/A F1

(PENCIL)SMARTGRIP

STRYKER

124 1922835003 N/A F1

(PENCIL)SMARTGRIP

STRYKER

125 1922835043 N/A F1

(PENCIL)SMARTGRIP

STRYKER

126 1714208503 N/A PI DRIVE+ MOTOR