SOL SPRRA124R0064 CS signed.pdf

SOLICITATION, OFFER AND AWARD 1. This Contract Is A Rated Order Under

DPAS (15 CFR 700)

Rating Page of Pages

2. Contract Number 3. Solicitation Number 4. Type of Solicitation 5. Date Issued 6. Requisition/Purchase Number Sealed Bid (IFB)

Negotiated (RFP)

7. Issued By Code 8. Address Offer To (If Other Than Item 7)

NOTE: In sealed bid solicitations ‘offer’ and ‘offeror’ mean ‘bid’ and ‘bidder’.

SOLICITATION

9. Sealed offers in original and copies for furnishing the supplies or services in the Schedule will be received at the place specified in item 8, or if handcarried, in the depository located in until (hour) local time (Date).

Caution - Late Submissions, Modifications, and Withdrawals: See Section L, Provision No. 52.214-7 or 52.215-1. All offers are subject to all terms and conditions contained in this solicitation.

10. For Information A. Name B. Telephone (No Collect Calls) C. E-mail Address

Call: Area Code Number Ext.

11. Table Of Contents

(X) Sec. Description Page(s) (X) Sec. Description Page(s)

Part I - The Schedule Part II - Contract Clauses A Solicitation/Contract Form I Contract Clauses

B Supplies or Services and Prices/Costs Part III - List Of Documents, Exhibits, And Other Attach.

C Description/Specs./Work Statement J List of Attachments D Packaging and Marking Part IV - Representations And Instructions E Inspection and Acceptance K Representations, Certifications, and F Deliveries or Performance Other Statements of Offerors G Contract Administration Data L Instrs., Conds., and Notices to Offerors H Special Contract Requirements M Evaluation Factors for Award

OFFER (Must be fully completed by offeror) NOTE: Item 12 does not apply if the solicitation includes the provisions at 52.214-16, Minimum Bid Acceptance Period.

12. In compliance with the above, the undersigned agrees, if this offer is accepted within _____ calendar days (60 calendar days unless a different period is inserted by the offeror) from the date for receipt of offers specified above, to furnish any or all items upon which prices are offered at the price set opposite each item, delivered at the designated point(s), within the time specified in the schedule.

13. Discount For Prompt Payment 10 Calendar Days (%) 20 Calendar Days (%) 30 Calendar Days (%) Calendar Days (%) (See Section I, Clause No. 52.232-8)

14. Acknowledgment of Amendments (The offeror acknowledges Amendment No. Date Amendment No. Date receipt of amendments to the SOLICITATION for offerors and related documents numbered and dated):

15A. Name and Code Facility 16. Name and Title of Person Authorized to Sign Offer Address of (Type or Print) Offeror

15B. Telephone Number 15C. Check if Remittance Address is 17. Signature 18. Offer Date Area Code Number Ext. Different From Above – Enter such

Address In Schedule

AWARD (To be completed by Government)

19. Accepted As To Items Numbered 20. Amount 21. Accounting And Appropriation

22. Authority For Using Other Than Full And Open Competition: 23. Submit Invoices To Address Shown In Item

10 U.S.C. 2304(c)( ) 41 U.S.C. 253(c)( ) (4 copies unless otherwise specified)

24. Administered By (If other than Item 7) Code 25. Payment Will Be Made By Code

26. Name of Contracting Officer (Type or Print) 27. United States Of America 28. Award Date

(Signature of Contracting Officer)

IMPORTANT - Award will be made on this Form, or on Standard Form 26, or by other authorized official written notice.

AUTHORIZED FOR LOCAL REPRODUCTION Standard Form 33 (Rev. 9-97) Previous edition is unusable Prescribed By GSA-FAR (48 CFR) 53.214(c)

SPRRA1-24-R-0064

X

2024JUL09

2024AUG2305:00pm

DOA1

2024JUL09 SEE SCHEDULE

SPRRA1

DEFENSE LOGISTICS AGENCY

5201 MARTIN ROAD/DLA-AVN-AH

REDSTONE ARSENAL AL 35898-7340

MARK A. HIGHLAND

(256)690-5749

DLA-AVN-AHAA

MARK.HIGHLAND@DLA.MIL

1 69

X 1

X 5

X 13 X 14 X 15

X 21

X 23

X 29

X 45

X 46

X 59

X 68

CONTINUATION SHEET

Reference No. of Document Being Continued Page of

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

SECTION A - SUPPLEMENTAL INFORMATION

Buyer Name: MARK A. HIGHLAND

Buyer Office Symbol/Telephone Number: DLA-AVN-AHAA/(256)690-5749

Type of Contract 1: Firm Fixed Price

Kind of Contract: Supply Contracts and Priced Orders

*** End of Narrative A0000 ***

A-1. THIS REQUIREMENT IS FOR LIMITED SOURCES TO W AND G MACHINE COMPANY, INC. CAGE 33682, SIKORSKY AIRCRAFT CORPORATION CAGE 78286, CLIFFDALE MANUFACTURING LLC CAGE 347085 & ROTAIR AEROSPACE CORPORATION CAGE 54878. IAW 10 U.S.C. 2304 (c)(1) FAR 6.302-1 (a)(2) "A

LIMITED NUMBER OF RESPONSIBLE SOURCES, AND NO OTHER TYPE OF SUPPLIES OR SERVICES WILL SATISFY AGENCY REQUIREMENTS, FULL AND OPEN

COMPETITION NEED NOT BE ACCOUNTED FOR."

A-2. THIS EFFORT IS IN SUPPORT OF THE UH-60 (BE) BLACKHAWK FOR THE FOLLOWING:

NSN: 1650-01-285-3024

PN: 70106-08100-046

A-3. THIS IS A THREE-YEAR INDEFINITE DELIVERY REQUIREMENTS FIRM FIXED PRICE SOLICITATION. THE GOVERNMENT INTENDS TO ISSUE A DELIVERY

ORDER FOR A QUANTITY OF 270 EACH WITH THE BASE AWARD. HOWEVER, THE GOVERNMENT IS NOT OBLIGATED TO ISSUE ANY ORDERS AS A RESULT OF AN

AWARD AGAINST THIS SOLICITATION. ADDITIONALLY, IT RESERVES THE RIGHT TO ORDER ANY QUANTITY UP TO OR ABOVE THE INTENDED QUANTITY FOR THE

DURATION OF THE CONTRACT.

BY REPLYING TO THIS SOLICITATION AND SUBMITTING A QUOTATION OR PROPOSAL, THE OFFEROR IS ACKNOWLEDGING ITS ABILITY TO SUPPORT THIS

REQUIREMENT FOR THE FULL SOLICITED TIME PERIOD.

FUNDS WILL BE OBLIGATED/CITED UPON ISSUANCE OF EACH DELIVERY ORDER.

A-4. FLIGHT SAFETY/CRITICAL SAFETY ITEM (CSI) IS NOT REQUIRED.

A-5. PRODUCTION LOT TESTING (PLT) IS NOT REQUIRED.

A-6. FIRST ARTICLE TEST (FAT) IS REQUIRED. ALL FAT REPORTS SHALL BE SUBMITTED IN ENGLISH.

A-7. SERIAL NUMBER REQUIREMENT REPORTING (SNRR) MARKINGS ARE REQUIRED.

A-8. THE AVIATION MAINTENANCE MANAGEMENT SYSTEM-AVIATION (TAMMS-A) MARKINGS ARE REQUIRED.

A-9. REUSABLE CONTAINER PRICE MUST BE INCORPORATED INTO THE UNIT PRICE.

A-10. IUID MARKINGS ARE REQUIRED. "THE DFARS CLAUSE 252.211-7003 ITEM IDENTIFICATION AND VALUATION IS INCLUDED IN SECTION F".

A-11. ARMS EXPORT CONTROL IS APPLICABLE. "THE TECHNICAL DATA PACKAGE CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS

EXPORT CONTROL ACT (TITLE 22 U.S.C., SEC 2751 ET SEQ.) OR EXECUTIVE ORDER 12470. VIOLATION OF THESE EXPORT LAWS ARE SUBJECT TO SEVERE

CRIMINAL PENALTIES."

EXPORT CONTROL REQUIRES THE APPLICABLE CERTIFICATIONS TO BE CURRENT FOR BOTH THE QUOTER AND MANUFACTURER. THE OFFEROR AND ANY SOURCE(S)

OF SUPPLY IT WILL USE FOR CONTRACT PERFORMANCE MUST HAVE AN ACTIVE UNITED STATES/CANADA JOINT CERTIFICATION PROGRAM (JCP) CERTIFICATION

TO ACCESS EXPORT-CONTROLLED DATA. DLA DOES NOT INTEND TO DELAY AWARD IN ORDER FOR AN INELIGIBLE OFFER OR ITS SOURCE(S) SUPPLY TO APPLY

FOR AND RECEIVE AUTHORITY APPROVAL TO ACCESS THE EXPORT-CONTROLLED DATA.

A-12. SERIAL NUMBERING IS REQUIRED.

A-13. FIT CHECK IS NOT REQUIRED.

A-14. CONTRACTOR POINT OF CONTACT:

NAME: TBD

TELEPHONE NUMBER: TBD

E-MAIL ADDRESS: TBD

A-15. DCMA POINT OF CONTACT:

NAME: TBD

TELEPHONE NUMBER: TBD

E-MAIL ADDRESS: TBD

2 69

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

A-16. CONTRACT SPECIALIST POINT OF CONTACT:

NAME: MARK A. HIGHLAND

TELEPHONE NUMBER: (256) 690-5749

E-MAIL ADDRESS: MARK.HIGHLAND@DLA.MIL

FACSIMILE PROPOSALS WILL NOT BE ACCEPTED. ALL PROPOSALS SHALL BE E-MAILED

IAW FAR 52.219-9 ALT II, VENDOR SHALL SUBMIT SUBCONTRACTING PLAN ALONG WITH PROPOSAL.

"(SUPPLIER NAME)_____________________ APPROVED SUBCONTRACTING PLAN IS HEREBY INCORPORATED BY REFERENCE AND MADE A PART OF THIS CONTRACT.

THE EFFECTIVE PERIOD OF THIS PLAN IS (INSERT DATE)_____________________ TO (INSERT DATE) _____________________"

WHEN SUBMITTING REPORTS IN eSRS, PLEASE USE THE FOLLOWING EMAIL ADDRESS: DLAHSVSUBK@DLA.MIL

A-17. ACCELERATED DELIVERY IS ENCOURAGED AND AUTHORIZED AT NO ADDITIONAL COST TO THE GOVERNMENT.

A-18. PLEASE SUBMIT ALL FAT REPORTS, INQUIRIES, AND QUESTIONS TO:

DLA AVIATION HUNTSVILLE POST AWARD TEAM

5206 MARTIN ROAD

REDSTONE ARSENAL, ALABAMA 35898

OR

EMAIL TO: DLAHSVPOSTAWARDTEAM@DLA.MIL

A-19. CONTRACTOR FIRST ARTICLE TEST:

NUMBER OF SAMPLES TO BE TESTED = 1

INSPECTION: ORIGIN (DCMA)

ACCEPTANCE: ORIGIN (DCMA)

DELIVER FOB: DESTINATION

BY: 528 DACA

FIRST ARTICLE TEST PEPORT:

THE FIRST ARTICLE TEST REPORT WILL BE SENT ELECTRONICALLY TO:

DLAHSVPOSTAWARDTEAM@DLA.MIL

IF THE FILE IS TOO LARGE OR ENCRYPTION IS NEEDED, A DOD SAFE LINK WILL BE SENT TO YOU FOR UPLOAD USING HTTPS://SAFE.APPS.MIL/ .

PLEASE USE THE DLAHSVPOSTAWARDTEAM@DLA.MIL EMAIL ADDRESS TO REQUEST THE LINK.

INSPECTION: ORIGIN (DCMA)

ACCEPTANCE: DESTINATION (SPRRA1) BY THE PCO

SHIP TO: SPRRA1 (DLAHSVPOSTAWARDTEAM@DLA.MIL)

WAWF SUBMITTAL WILL BE A COMBO

ACCEPTANCE OF THE FATR WILL TAKE PLACE FIRST AND THEN ACCEPTANCE OF THE FAT BY DCMA WILL COMMENCE.

DELIVERY SCHEDULE:

528 DACA: CONTRACTOR FIRST ARTICLE COMPLETED AND REPORT SUBMISSION

45 DAYS: GOVERNMENT REVIEW AND NOTIFICATION TO CONTRACTOR

237 DAFAA: DELIVERY OF PRODUCTION UNITS_______________________________________

810 DACA

FIRST ARTICLE TEST (FAT) VERBIAGE:__________________________________

FIRST ARTICLE TEST TIME IS 3 DAYS. UNITS TO BE TESTED IS 1 EACH. FIRST ARTICLE TEST SHALL BEGIN ON A MUTUALLY AGREED UPON DATE BETWEEN

THE GOVERNMENT AND THE CONTRACTOR. THE DATE SHALL OCCUR WITH ENOUGH TIME IN ADVANCE TO BEGIN SCHEDULED DELIVERIES 528 DACA. THE

CONTRACTOR SHALL NOTIFY THE CONTRACTING OFFICER IN WRITING 30 DAYS PRIOR TO THE PROPOSED DATE OF FIRST ARTICLE TESTING. THE FIRST

ARTICLE TEST REPORT IS DUE 15 DAYS AFTER FAT. THE PREFERRED METHOD OF TRANSMITTAL IS CD. THE GOVERNMENT HAS 45 DAYS TO

APPROVE/DISAPPROVE THE TEST REPORT.

OTHER THAN CERTIFIED COST AND PRICING DATA:___________________________________________

NOTICE: YOUR ATTENTION IS INVITED TO FEDERAL ACQUISITION REGULATION (FAR) 15.403-4, RELATIVE TO THE REQUIREMENT FOR OBTAINING OTHER THAN

CERTIFIED COST AND PRICING DATA. IN THE EVENT ONLY ONE (1) OFFER IS RECEIVED IN RESPONSE TO THIS SOLICITATION, THE SOLE OFFEROR IS

REQUIRED TO SUBMIT CERTIFIED COST AND PRICING DATA UPON REQUEST. FAILURE TO PROVIDE CERTIFIED COST AND PRICING DATA WILL RESULT IN YOUR

OFFER BEING CONSIDERED NON-RESPONSIVE.

LONG LEAD TIME AND OR LONG-TERM CONTRACTS:__________________________________________

FOR LONG LEAD TIME ITEMS AND/OR LONG-TERM CONTRACTS, THE PARTIES RECOGNIZE THERE IS A RISK THAT PART(S) OR COMPONENT(S) REQUIRED FOR

PERFORMANCE OF THE CONTRACT/PURCHASE ORDER MAY BECOME UNAVAILABLE DUE TO OBSOLESCENCE. UPON RECEIPT OF THE CONTRACT/PURCHASE ORDER, 3 69

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

CONTRACTOR IS RESPONSIBLE FOR VERIFYING ITS SOURCES OF SUPPLY. IF AT ANY TIME DURING THE COURSE OF PERFORMANCE CONTRACTOR BECOMES AWARE

THAT IT IS UNABLE TO PROCURE A PART OR COMPONENT NECESSARY TO FULFILL THE REQUIREMENTS OF THE CONTRACT, THE CONTRACTOR SHALL NOTIFY THE

CONTRACTING OFFICER IN WRITING WITHIN THIRTY DAYS. NOTIFICATION SHALL INCLUDE CONTRACTOR'S RECOMMENDATION FOR CORRECTION OF THE PROBLEM, IF POSSIBLE, WITH ESTIMATED COST AND SCHEDULE IMPACT, IF ANY. THE CONTRACTING OFFICER WILL DETERMINE THE APPROPRIATE COURSE OF ACTION

AND PROVIDE DIRECTION TO THE CONTRACTOR. IN NO EVENT WILL CONTRACTOR PROCEED WITH IMPLEMENTATION OF ITS RECOMMENDATION WITHOUT WRITTEN

DIRECTION FROM THE CONTRACTING OFFICER. AT THE SOLE DISCRETION OF THE CONTRACTING OFFICER, THE CONTRACT MAY BE TERMINATED IN WHOLE OR IN

PART, AS APPROPRIATE.

PRODUCT QUALITY DEFICIENCY REPORTS (PQDRS)__________________________________________

THE PRODUCT QUALITY DEFICIENCY REPORT PROGRAM (ARMY REGULATION 702-7) WILL BE USED WHEN CONTRACTORS: 1) DELIVER DEFICIENT ITEMS OR 2)

RECEIVE DEFICIENT ITEMS FROM A DOD SUPPLY CHAIN IN SUPPORT OF ARMY REQUIREMENTS. WHEN REQUESTED, THE CONTRACTOR SHALL ASSIST THE

COGNIZANT CONTRACT ADMINISTRATION OFFICE IN EVALUATING PQDRS AND EXHIBITS FOR DEFECTS REPORTED ON ITEMS MANUFACTURED UNDER THIS CONTRACT

TO DETERMINE THE ROOT CAUSE FOR DEFICIENCIES. CORRECTIVE ACTION AND PREVENTATIVE ACTION TO PRECLUDE RECURRENCE OF DISCREPANCIES SHALL BE

AN INTEGRAL PART OF THE CONTRACTORS QUALITY PROGRAM. THESE DEFECTS MAY BE REPORTED FROM ANY DOD ACTIVITY THAT DISCOVERS A DEFECTIVE

ITEM.

*** END OF NARRATIVE A0001 ***

4 69

PIIN/SIIN

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

SECTION B - SUPPLIES OR SERVICES AND PRICES/COSTS

APPROVED SOURCES:

SIKORSKY AIRCRAFT CORPORATION CAGE 78286

ROTAIR INDUSTRIES, INC CAGE 54878

CLIFFDALE MANUFACTURING LLC CAGE 34705

W&G MACHINE COMPANY INC CAGE 33682

IN RESPONSE TO THE REQUEST FOR INFORMATION, ROTAIR

AND W&G MACHINE BOTH STATED THAT THEY WILL PROVIDE A

PROPOSAL FOR THIS PROCUREMENT. SIKORSKY AND

CLIFFDALE DID NOT RESPOND TO THE REQUEST FOR

INFORMATION. THIS WILL BE CONSIDERED A LIMITED

COMPETITIVE ACTION.

(End of narrative A001)

0001 DAMPENER, FLUTTER

NSN: 1650-01-285-3024

Mfr CAGE: 81996

Mfr Part Number: 70106-08100-046

THIS IS A THREE YEAR INDEFINITE DELIVERY

REQUIREMENTS TYPE SOLICITATION. FUNDS WILL BE

OBLIGATED/CITED UPON THE ISSUANCE OF EACH

DELIVERY ORDER. THE ESTIMATED QUANTITIES HEREIN

ARE NOT A REPRESENTATION TO AN OFFEROR OR

CONTRACTOR THAT THE ESTIMATED QUANTITY WILL BE

REQUIRED OR ORDERED, OR THAT CONDITIONS AFFECTING

REQUIREMENTS WILL BE STABLE OR NORMAL.

THE ESTIMATED QUANTITIES ANNOTATED WITHIN THIS

SOLICITATION ARE BASED ON THE MOST CURRENT

REQUIREMENT INFORMATION AVAILABLE.

THE GOVERNMENT INTENDS TO PROCURE A MINIMUM

QUANTITY OF 270 EACH. THE GOVERNMENT IS NOT

OBLIGATED TO ISSUE ANY ORDERS AGAINST THIS

CONTRACT OVER THE GUARANTEED CONTRACT MINIMUM

AMOUNT; HOWEVER, THE GOVERNMENT RESERVES THE

RIGHT TO ORDER ANY QUANTITY ABOVE THE GUARANTEED

CONTACT MINIMUM QUANTITY FOR THE DURATION OF THIS

CONTRACT.

BY REPLYING TO THIS SOLICITATION AND SUBMITTING A

QUOTATION OR PROPOSAL, THE OFFEROR IS

ACKNOWLEDGING ITS ABILITY TO SUPPORT THIS

REQUIREMENT FOR THE FULL SOLICITED TIME PERIOD.

THE GOVERNMENT HAS SEGREGATED THE ESTIMATED

QUANTITIES INTO THREE, ONE-YEAR ORDERING PERIODS.

HOWEVER, THIS DOES NOT PREVENT THE GOVERNMENT

FROM EXERCISING ITS RIGHTS UNDER FAR 52.216-21 AT

ANY TIME DURING THE REQUIREMENT PERIOD.

5 69

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

THE INTENDED QUANTITY TO BE AWARDED

SIMULTANEOUSLY WITH THE AWARD OF THE BASIC

CONTRACT IS 270 EACH. DELIVERY ORDERS ISSUED

UNDER THIS CONTRACT SHALL NOT HAVE OVERLAPPING

DELIVERY SCHEDULES.

PRICES QUOTED FOR EACH ORDERING YEAR WILL BE

VALID FOR ALL QUANTITIES ORDERED DURING THAT

ORDERING PERIOD.

THE SOLICITATION IS FOR THE SUPPLIES AS DETAILED

ON THE FOLLOWING PAGES. OFFERORS ARE CAUTIONED TO

INSURE THAT OFFERS ARE PROVIDED ON ALL

QUANTITIES. FAILURE TO PROPOSE ALL CLINS, MAY

RESULT IN A DETERMINATION OF NON RESPONSIVENESS.

AN OFFER MAY BE REJECTED IF THE GOVERNMENT

DETERMINES THAT THE OFFER IS MATERIALLY

UNBALANCED OR IF THE OFFER CONTAINS UNBALANCED

PRICING.

YEAR 1 WILL BE FROM DATE OF AWARD THROUGH DAY 365

DAYS AFTER CONTRACT AWARD (DACA).

YEAR 2 WILL BEGIN 366 DACA AND END 730 DACA.

YEAR 3 WILL BEGIN 731 DACA AND END 1,095 DACA.

ALL REFERENCES TO F.O.B. ORIGIN THROUGHOUT THIS

SOLICITATION APPLY TO ALL QUANTITIES ORDERED

AFTER THE FIRST DELIVERY ORDER.

THE ESTIMATED (E) QUANTITY LISTED HEREIN DOES NOT

COMMIT THE GOVERNMENT TO ORDER THAT OR ANY

QUANTITY ABOVE THE MINIMUM QUANTITY.

THE GOVERNMENT INTENDS TO AWARD ONLY ONE

REQUIREMENTS TYPE BASIC CONTRACT AS A RESULT OF

THIS SOLICITATION.

(End of narrative B001)

0001AA PRODUCTION QUANTITY 270 (E) EA $ $ ___________________ ______________ __________________

PROGRAM YEAR: 1

COMMODITY NAME: DAMPENER, FLUTTER

CLIN CONTRACT TYPE:

Firm Fixed Price

Description/Specs./Work Statement _________________________________

TOP DRAWING NR: 70106-08100-046

UNIT PRICE IS INCLUSIVE OF CONTRACTOR FURNISHED

CONTAINER:

UNIT PRICE: $___________

CONTAINER COST: $___________

6 69

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

(End of narrative C001)

Packaging and Marking _____________________

PACKAGING/PACKING/SPECIFICATIONS:

IAW MIL-STD CODES 2073-1 APPENDIX J

UNIT PACK: 001 INTERMEDIATE PACK: 000

LEVEL PRESERVATION: Military

LEVEL PACKING: A

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Origin

Deliveries or Performance _________________________

FOB POINT: Destination

SHIP TO:

(Y00000) SHIPPING INSTRUCTIONS FOR CONSIGNEE

(SHIPTO) WILL BE FURNISHED PRIOR TO THE SCHEDULED

DELIVERY DATE FOR ITEMS REQUIRED UNDER THIS

REQUISITION.

(End of narrative F001)

0002 DAMPENER, FLUTTER

NSN: 1650-01-285-3024

Mfr CAGE: 81996

Mfr Part Number: 70106-08100-046

0002AA PRODUCTION QUANTITY 351 (E) EA $ $ ___________________ ______________ __________________

PROGRAM YEAR: 2

COMMODITY NAME: DAMPENER, FLUTTER

CLIN CONTRACT TYPE:

Firm Fixed Price

Description/Specs./Work Statement _________________________________

TOP DRAWING NR: 70106-08100-046

UNIT PRICE IS INCLUSIVE OF CONTRACTOR FURNISHED

CONTAINER:

UNIT PRICE: $___________

CONTAINER COST: $___________

(End of narrative C001)

7 69

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

Packaging and Marking _____________________

PACKAGING/PACKING/SPECIFICATIONS:

IAW MIL-STD CODES 2073-1 APPENDIX J

UNIT PACK: 001 INTERMEDIATE PACK: 000

LEVEL PRESERVATION: Military

LEVEL PACKING: A

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Origin

Deliveries or Performance _________________________

FOB POINT: Origin

SHIP TO:

(Y00000) SHIPPING INSTRUCTIONS FOR CONSIGNEE

(SHIPTO) WILL BE FURNISHED PRIOR TO THE SCHEDULED

DELIVERY DATE FOR ITEMS REQUIRED UNDER THIS

REQUISITION.

(End of narrative F001)

0003 DAMPENER, FLUTTER

NSN: 1650-01-285-3024

Mfr CAGE: 81996

Mfr Part Number: 70106-08100-046

0003AA PRODUCTION QUANTITY 351 (E) EA $ $ ___________________ ______________ __________________

PROGRAM YEAR: 3

COMMODITY NAME: DAMPENER, FLUTTER

CLIN CONTRACT TYPE:

Firm Fixed Price

Description/Specs./Work Statement _________________________________

TOP DRAWING NR: 70106-08100-046

UNIT PRICE IS INCLUSIVE OF CONTRACTOR FURNISHED

CONTAINER:

UNIT PRICE: $___________

CONTAINER COST: $___________

(End of narrative C001)

8 69

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

Packaging and Marking _____________________

PACKAGING/PACKING/SPECIFICATIONS:

IAW MIL-STD CODES 2073-1 APPENDIX J

UNIT PACK: 001 INTERMEDIATE PACK: 000

LEVEL PRESERVATION: Military

LEVEL PACKING: A

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Origin

Deliveries or Performance _________________________

FOB POINT: Origin

SHIP TO:

(Y00000) SHIPPING INSTRUCTIONS FOR CONSIGNEE

(SHIPTO) WILL BE FURNISHED PRIOR TO THE SCHEDULED

DELIVERY DATE FOR ITEMS REQUIRED UNDER THIS

REQUISITION.

(End of narrative F001)

0004 CONTRACT DATA REQUIREMENTS LIST _______________________________

A001 THE ARMY MAINTENANCE MGT SYSTEM-AVIATION (TAMMS-A) 1 EA $ ** NSP ** $ ** NSP ** __________________________________________________ ______________ __________________

COMMODITY NAME: DAMPENER, FLUTTER

CLIN CONTRACT TYPE:

Firm Fixed Price

Description/Specs./Work Statement _________________________________

PROCUREMENT DOCUMENTATION TITLE:

DI-SESS-81758A

Packaging and Marking _____________________

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Destination

Deliveries or Performance _________________________

DOC SUPPL

REL CD MILSTRIP ADDR SIG CD MARK FOR TP CD ______ ________ ______ ______ ________ _____

001 3

DEL REL CD QUANTITY DEL DATE __________ ______________ ___________

001 1 AS REQUIRED

FOB POINT: Destination

9 69

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

SHIP TO:

(W81D17) XU W0H9 US ARMY AVN & MISSLES CMD

TAMMS A IMPLEMENTATION AND COMP BR

SPARKMAN CIR BLDG 5300 4TH FLOOR

REDSTONE ARSENAL,AL,35898-5230

A002 SERIAL NUMBER REPORTING REQUIREMENT (SNRR) 1 EA $ ** NSP ** $ ** NSP ** __________________________________________ ______________ __________________

COMMODITY NAME: DAMPENER, FLUTTER

Description/Specs./Work Statement _________________________________

PROCUREMENT DOCUMENTATION TITLE:

DI-SESS-81759A

Packaging and Marking _____________________

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Destination

Deliveries or Performance _________________________

DOC SUPPL

REL CD MILSTRIP ADDR SIG CD MARK FOR TP CD ______ ________ ______ ______ ________ _____

001 3

DEL REL CD QUANTITY DEL DATE __________ ______________ ___________

001 1 AS REQUIRED

FOB POINT: Destination

SHIP TO:

(W81D17) XU W0H9 US ARMY AVN & MISSLES CMD

TAMMS A IMPLEMENTATION AND COMP BR

SPARKMAN CIR BLDG 5300 4TH FLOOR

REDSTONE ARSENAL,AL,35898-5230

0005 COST OF FIRST ARTICLE TEST (FAT) 1 EA $ $ ________________________________ ______________ __________________

COMMODITY NAME: DAMPENER, FLUTTER

CLIN CONTRACT TYPE:

Firm Fixed Price

FIRST ARTICLE TEST ITEM IS 3 DAYS. UNITS TO BE

TESTED IS 1 EACH. BEGIN TESTING 510 DAYS AFTER

CONTRACT AWARD(DACA). END TESTING 513 DACA. FIRST

ARTICLE TEST REPORT DUE 528 DACA.

THE GOVERNMENT HAS 45 DAYS TO APPROVE/DISAPPROVE THE

10 69

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

TEST REPORT. THE FIRST ARTICLE TEST UNIT SHALL NOT

BE RETAINED BY THE CONTRACTOR AS A MANUFACTURING

STANDARD.

FAR 52.209-3 ALTERNATE I IS INCLUDED UNDER WHICH

THE CONTRACTOR IS REQUIRED TO PRODUCE THE FIRST

ARTICLE AND THE PRODUCTION QUANTITY AT THE SAME

FACILITY.

THE FAT REPORT WILL BE SUBMITTED IN ENGLISH.

CLIN 0005 IS NOT RESTRICTED TO A SPECIFIC

ORDERING PERIOD AND MAY BE IMPLEMENTED WITH ANY

ORDER DURING THE DURATION OF THE THREE YEAR IDR

AT THE DISCRETION OF THE QUALITY OVERSEER IN

ACCORDANCE WITH FAR SUBPART 9.3. THIS IN NO WAY

PRECLUDES THE CONTRACTORS RIGHT TO SUBMIT A

REQUEST FOR WAIVER OF THE FAT, ALTHOUGH A WAIVER

IS NOT GUARANTEED.

(End of narrative B001)

Packaging and Marking _____________________

Government Approval/Disapproval Days: 45

Deliveries or Performance _________________________

FOB POINT:

SHIP TO:

(SPRRA1) DLA AVIATION AT HUNTSVILLE, AL

DLR PROCUREMENT OPERATIONS (AH)

5201 MARTIN ROAD

REDSTONE ARSENAL,AL,35898-7340

0006 FIRST ARTICLE TEST REPORT 1 EA $ ** NSP ** $ ** NSP ** _________________________ ______________ __________________

COMMODITY NAME: DAMPENER, FLUTTER

CLIN CONTRACT TYPE:

Firm Fixed Price

Packaging and Marking _____________________

Inspection and Acceptance _________________________

INSPECTION: Origin ACCEPTANCE: Destination

Deliveries or Performance _________________________

DOC SUPPL

REL CD MILSTRIP ADDR SIG CD MARK FOR TP CD ______ ________ ______ ______ ________ _____

001 3

DEL REL CD QUANTITY DEL DATE __________ ______________ ___________

11 69

Page of

Name of Offeror or Contractor:

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

Reference No. of Document Being Continued

MOD/AMD

001 1 AS REQUIRED

FOB POINT: Destination

SHIP TO:

(SPRRA1) DLA AVIATION AT HUNTSVILLE, AL

DLR PROCUREMENT OPERATIONS (AH)

5201 MARTIN ROAD

REDSTONE ARSENAL,AL,35898-7340

FIRST ARTICLE TEST ITEM IS 3 DAYS. UNITS TO BE

TESTED IS 1 EACH. BEGIN TESTING 510 DAYS AFTER

CONTRACT AWARD (DACA). END TESTING 513 DACA. FIRST

ARTICLE TEST REPORT DUE 528 DACA. THE GOVERNMENT HAS

45 DAYS TO APPROVE/DISAPPROVE THE TEST REPORT.

(End of narrative F001)

12 69

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

SECTION D - PACKAGING AND MARKING

MIL-STD-129 MARKINGS SHALL APPLY

UNIT PACK: 001 INTERMEDIATE PACK: 000

LEVEL PRESERVATION: MILITARY LEVEL PACKING: A

ADDITIONAL PACKAGING REQUIREMENTS

ESTIMATED MAXIMUM UNIT PACKAGE WEIGHT (POUNDS) AND SIZE (INCHES)

WT [51.5] LB

LN [31.0] IN

WD [21.0] IN

DP [15.0] IN

ALL WOOD PACKAGING MATERIAL (WPM) MUST BE ISPM-15 COMPLIANT

MIL-STD-2073-1 Codes, APPENDIX J

JI/A/MP [44] JII/CD [1] JIII/PM [00] JIV/WM [GH] JV/CD [NA]

JVI/CT [Z] JVII/UC [NZ] JVII/IC [00] JIX/A/PK [F] JX/SM [17]

JVIIIA/OPI [M]

SUPPLEMENTAL INFORMATION:

NZ = 8145-00-549-6647, 13414-078; Z = AS REQ'D TO SECURE ITEM

REUSABLE CONTAINER WILL BE CONTRACTOR FURNISHED MATERIAL

*** END OF NARRATIVE D0001 ***

13 69

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

SECTION E - INSPECTION AND ACCEPTANCE

The Government's Quality Assurance Representative (QAR) will inspect supplies described by manufacturer's name/code and part number at origin location(s):

The QAR may require that objective evidence be furnished establishing the name and address of the plant that manufactures the supplies to ensure that a domestic product is being supplied. Objective evidence of performance must be present for all quality assurance requirements specified in the contract. The QAR may require additional examinations and tests to determine:

Completeness of item

Material is new and unused

Absence of rust

Contamination, or deterioration

Correct identification/item marking

Correct packaging

Absence of any damage

Compliance with preparation for delivery

If the supplier is not the manufacturer of the supplies, objective evidence must be furnished to establish that the supplies were produced by the approved manufacturer.

For supplies designated as former Government surplus (whether described by manufacturers name/code and part number, or by Military or

Federal specification or drawing), the original package markings of each item shall be verified to previous Government contract number and part number. Any deviation shall be cause for rejection of the item. The Procuring Activity may add additional inspection requirements based on the evaluation of the surplus offer. Such additional requirements will be identified before the award.

*** END OF NARRATIVE E0001 ***

This document incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at these addresses:

For FAR clauses: https://www.acquisition.gov/

For DFARS clauses: https://www.acq.osd.mil/dpap/dars/dfarspgi/current/index.html

If the clause requires additional or unique information, then that information is provided immediately after the clause title.

Regulatory Cite Title Date Regulatory Cite Title Date _______________ ______________________________________________________________________ ____________ _______________ ______________________________________________________________________ ____________

E-1 52.246-2 INSPECTION OF SUPPLIES--FIXED-PRICE AUG/1996

E-2 52.246-16 RESPONSIBILITY FOR SUPPLIES APR/1984

E-3 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT DEC/2014

(a) The contractor shall comply with the higher-level quality standard(s) listed below.

ANSI/ISO/ASQ 9001:2008, AS 9100 OR EQUIVALENT, TAILORING: ALL PARAGRAPHS UNDER 7.3 (DESIGN AND DEVELOPMENT) DO NOT APPLY

(b) The contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph (a) of this clause and the requirement to flow down such standards, as applicable, to lower-tier subcontracts in--

(1) Any subcontract for critical and complex items (see 46.203(b) and (c)); or

(2) When the technical requirements of a subcontract require--

(i) Control of such things as design, work operations, in-process control, testing and inspection; or

(ii) Attention to such factors as organization, planning, work instructions, documentation control, and advanced metrology.

(End of clause)

14 69

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

SECTION F - DELIVERIES OR PERFORMANCE

FOR CLINS 0001AA, 0002AA AND 0003AA: DELIVERIES WITHOUT FAT SHALL COMMENCE 540 DAYS AFTER CONTARCT AWARD. DELIVERIES WITH FAT SHALL

COMMENCE 810 DAYS AFTER CONTRACT AWRD.

THE FIRST ORDER TO BE ISSUED IN CONJUNCTION WITH CONTRACT AWARD WILL BE DELIVERED TO:

TEXARKANA, TX (W562RM)

SR W0MC ARMY GENERAL SUPPLY

DLA DISTRIBUTION RED RIVER

HIGHWAY 82 WEST

TEXARKANA, TX, 75507-5000

ADDITIONAL ORDERS UNDER CLINS 0001AA,0002AA,0003AA AND 0005: SHIP TO INSTRUCTIONS FOR CONSIGNEE WILL BE FURNISHED PRIOR TO SCHEDULED

DELIVERY DATE FOR ITEMS REQUIRED UNDER THIS REQUISITION.

*** END OF NARRATIVE F0001 ***

This document incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at these addresses:

For FAR clauses: https://www.acquisition.gov/

For DFARS clauses: https://www.acq.osd.mil/dpap/dars/dfarspgi/current/index.html

If the clause requires additional or unique information, then that information is provided immediately after the clause title.

Regulatory Cite Title Date Regulatory Cite Title Date _______________ ______________________________________________________________________ ____________ _______________ ______________________________________________________________________ ____________

F-1 52.211-17 DELIVERY OF EXCESS QUANTITIES SEP/1989

F-2 52.242-15 STOP-WORK ORDER AUG/1989

F-3 52.242-17 GOVERNMENT DELAY OF WORK APR/1984

F-4 52.247-29 F.O.B. ORIGIN FEB/2006

F-5 52.247-30 F.O.B. ORIGIN, CONTRACTOR'S FACILITY FEB/2006

F-6 52.247-34 F.O.B. DESTINATION NOV/1991

F-7 52.247-48 F.O.B. DESTINATION--EVIDENCE OF SHIPMENT FEB/1999

F-8 52.247-58 LOADING, BLOCKING, AND BRACING OF FREIGHT CAR SHIPMENTS APR/1984

F-9 52.247-59 F.O.B. ORIGIN--CARLOAD AND TRUCKLOAD SHIPMENTS APR/1984

F-10 52.247-65 F.O.B. ORIGIN, PREPAID FREIGHT--SMALL PACKAGE SHIPMENTS JAN/1991

F-11 252.211-7008 USE OF GOVERNMENT-ASSIGNED SERIAL NUMBERS SEP/2010

F-12 52.211-8 TIME OF DELIVERY JUN/1997

(a) The Government objective delivery scedule is:

OBJECTIVE DELIVERY SCHEDULE

ITEM NO. QUANTITY WITHIN DAYS

AFTER CONTRACT AWARD

CLIN 0001AA 270 EA 540 DAYS WITHOUT FAT; 810 DAYS WITH FAT

CLIN 0002AA 351 EA 540 DAYS WITHOUT FAT; 810 DAYS WITH FAT

CLIN 0003AA 351 EA 540 DAYS WITHOUT FAT; 810 DAYS WITH FAT

The government will evaluate time of delivery and use that to determine award as stated in EVALUATION FACTORS FOR AWARD below. The

Government reserves the right to award under either the objective delivery schedule or the proposed delivery schedule when an offeror offers an earlier delivery schedule than the objective delivery schedule. If the offeror proposes no other delivery schedule, the objective delivery schedule above will apply.

OFFERORS PROPOSED DELIVERY SCHEDULE

15 69

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

ITEM NO. QUANTITY WITHIN DAYS

AFTER CONTRACT AWARD

CLIN 0001AA 270 EA (E) _________________DACA

CLIN 0002AA 351 EA (E) _________________DACA

CLIN 0003AA 351 EA (E) _________________DACA

(b) Attention is directed to the Contract Award provision of the solicitation that provides that a written award or acceptance of offer mailed, or otherwise furnished to the successful offeror, results in a binding contract. The Government will mail or otherwise furnish to the offeror an award or notice of award not later than the day award is dated. Therefore, the offeror should compute the time available for performance beginning with the actual date of award, rather than the date the written notice of award is received from the

Contracting Officer through the ordinary mails. However, the Government will evaluate an offer that proposes delivery based on the

Contractors date of receipt of the contract or notice of award by adding

(1) five calendar days for delivery of the award through the ordinary mails, or

(2) one working day if the solicitation states that the contract or notice of award will be transmitted electronically. (The term working day excludes weekends and U.S. Federal holidays.) If, as so computed, the offered delivery date is later than the required delivery date, the offer will be considered nonresponsive and rejected.

(End of Clause)

F-13 52.211-11 LIQUIDATED DAMAGES--SUPPLIES, SERVICES, OR RESEARCH AND DEVELOPMENT SEP/2000

(a) If the Contractor fails to deliver the supplies or perform the services within the time specified in this contract, the Contractor shall, in place of actual damages, pay to the Government liquidated damages of TO BE DETERMINED per calendar day of delay.

(b) If the Government terminates this contract in whole or in part under the Default -- Fixed-Price Supply and Service clause, the

Contractor is liable for liquidated damages accruing until the Government reasonably obtains delivery or performance of similar supplies or services. These liquidated damages are in addition to excess costs of repurchase under the Termination clause.

(c) The Contractor will not be charged with liquidated damages when the delay in delivery or performance is beyond the control and without the fault or negligence of the Contractor as defined in the Default -- Fixed-Price Supply and Service clause in this contract.

(End of Clause)

F-14 252.211-7003 ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023) JAN/2023

(a) Definitions. As used in this clause--

"Automatic identification device" means a device, such as a reader or interrogator, used to retrieve data encoded on machine-readable media.

"Concatenated unique item identifier" means

(1) For items that are serialized within the enterprise identifier, the linking together of the unique identifier data elements in order of the issuing agency code, enterprise identifier, and unique serial number within the enterprise identifier; or

(2) For items that are serialized within the original part, lot, or batch number, the linking together of the unique identifier data elements in order of the issuing agency code; enterprise identifier; original part, lot, or batch number; and serial number within the original part, lot, or batch number.

"Data matrix" means a two-dimensional matrix symbology, which is made up of square or, in some cases, round modules arranged within a perimeter finder pattern and uses the Error Checking and Correction 200 (ECC200) specification found within International Standards

Organization (ISO)/International Electrotechnical Commission (IEC) 16022.

16 69

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

"Data qualifier" means a specified character (or string of characters) that immediately precedes a data field that defines the general category or intended use of the data that follows.

"DoD recognized unique identification equivalent" means a unique identification method that is in commercial use and has been recognized by DoD. All DoD recognized unique identification equivalents are listed at https://www.acq.osd.mil/asda/dpc/ce/ds/unique-id.html .

"DoD item unique identification" means a system of marking items delivered to DoD with unique item identifiers that have machine-readable data elements to distinguish an item from all other like and unlike items. For items that are serialized within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier and a unique serial number. For items that are serialized within the part, lot, or batch number within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier; the original part, lot, or batch number; and the serial number.

"Enterprise" means the entity (e.g., a manufacturer or vendor) responsible for assigning unique item identifiers to items.

"Enterprise identifier" means a code that is uniquely assigned to an enterprise by an issuing agency.

"Governments unit acquisition cost" means

(1) For fixed-price type line, subline, or exhibit line items, the unit price identified in the contract at the time of delivery;

(2) For cost-type or undefinitized line, subline, or exhibit line items, the Contractors estimated fully burdened unit cost to the

Government at the time of delivery; and

(3) For items produced under a time-and-materials contract, the Contractors estimated fully burdened unit cost to the Government at the time of delivery.

"Issuing agency" means an organization responsible for assigning a globally unique identifier to an enterprise, as indicated in the

Register of Issuing Agency Codes for ISO/IEC 15459, located at http://www.aimglobal.org/?Reg_Authority15459 .

"Issuing agency code" means a code that designates the registration (or controlling) authority for the enterprise identifier.

"Item" means a single hardware article or a single unit formed by a grouping of subassemblies, components, or constituent parts.

"Lot or batch number" means an identifying number assigned by the enterprise to a designated group of items, usually referred to as either a lot or a batch, all of which were manufactured under identical conditions.

"Machine-readable" means an automatic identification technology media, such as bar codes, contact memory buttons, radio frequency identification, or optical memory cards.

"Original part number" means a combination of numbers or letters assigned by the enterprise at item creation to a class of items with the same form, fit, function, and interface.

"Parent item" means the item assembly, intermediate component, or subassembly that has an embedded item with a unique item identifier or DoD recognized unique identification equivalent.

"Serial number within the enterprise identifier" means a combination of numbers, letters, or symbols assigned by the enterprise to an item that provides for the differentiation of that item from any other like and unlike item and is never used again within the enterprise.

"Serial number within the part, lot, or batch number" means a combination of numbers or letters assigned by the enterprise to an item that provides for the differentiation of that item from any other like item within a part, lot, or batch number assignment.

"Serialization within the enterprise identifier" means each item produced is assigned a serial number that is unique among all the tangible items produced by the enterprise and is never used again. The enterprise is responsible for ensuring unique serialization within the enterprise identifier.

"Serialization within the part, lot, or batch number" means each item of a particular part, lot, or batch number is assigned a unique serial number within that part, lot, or batch number assignment. The enterprise is responsible for ensuring unique serialization within the part, lot, or batch number within the enterprise identifier.

"Type designation" means a combination of letters and numerals assigned by the Government to a major end item, assembly or subassembly, as appropriate, to provide a convenient means of differentiating between items having the same basic name and to indicate modifications and changes thereto.

17 69

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

"Unique item identifier" means a set of data elements marked on items that is globally unique and unambiguous. The term includes a concatenated unique item identifier or a DoD recognized unique identification equivalent.

"Unique item identifier type" means a designator to indicate which method of uniquely identifying a part has been used. The current list of accepted unique item identifier types is maintained at https://www.acq.osd.mil/asda/dpc/ce/ds/unique-id.html .

(b) The Contractor shall deliver all items under a contract line, subline, or exhibit line item.

(c) Unique item identifier.

(1) The Contractor shall provide a unique item identifier for the following:

(i) Delivered items for which the Government's unit acquisition cost is $5,000 or more, except for the following line items:

Contract Line, Subline, or

Exhibit Line Item Number Item Description

__N/A______________ N/A___________________________________

(ii) Items for which the Government's unit acquisition cost is less than $5,000 that are identified in the Schedule or the following table:

Contract Line, Subline, or

Exhibit Line Item Number Item Description

__N/A______________ N/A___________________________________

(iii) Subassemblies, components, and parts embedded within delivered items, items with warranty requirements, DoD serially managed reparables and DoD serially managed nonreparables as specified in

Attachment Number N/A.

(iv) Any item of special tooling or special test equipment as defined in FAR 2.101 that have been designated for preservation and storage for a Major Defense Acquisition Program as specified in

Attachment Number N/A.

(v) Any item not included in paragraphs (c)(1)(i), (ii), (iii), or (iv) of this clause for which the contractor creates and marks a unique item identifier for traceability.

(2) The unique item identifier assignment and its component data element combination shall not be duplicated on any other item marked or registered in the DoD Item Unique Identification Registry by the contractor.

(3) The unique item identifier component data elements shall be marked on an item using two dimensional data matrix symbology that complies with ISO/IEC International Standard 16022, Information technology--International symbology specification--Data matrix; ECC200 data matrix specification.

(4) Data syntax and semantics of unique item identifiers. The Contractor shall ensure that--

(i) The data elements (except issuing agency code) of the unique item identifier are encoded within the data matrix symbol that is marked on the item using one of the following three types of data qualifiers, as determined by the Contractor:

(A) Application Identifiers (AIs) (Format Indicator 05 of ISO/IEC International Standard 15434), in accordance with ISO/IEC

International Standard 15418, Information Technology--EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI

MH 10.8.2 Data Identifier and Application Identifier Standard.

(B) Data Identifiers (DIs) (Format Indicator 06 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International

Standard 15418, Information Technology--EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2

Data Identifier and Application Identifier Standard.

(C) Text Element Identifiers (TEIs) (Format Indicator 12 of ISO/IEC International Standard 15434), in accordance with the Air

18 69

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

Transport Association Common Support Data Dictionary; and

(ii) The encoded data elements of the unique item identifier conform to the transfer structure, syntax, and coding of messages and data formats specified for Format Indicators 05, 06, and 12 in ISO/IEC International Standard 15434, Information Technology-Transfer

Syntax for High Capacity Automatic Data Capture Media.

(5) Unique item identifier.

(i) The Contractor shall--

(A) Determine whether to--

(1) Serialize within the enterprise identifier;

(2) Serialize within the part, lot, or batch number; or

(3) Use a DoD recognized unique identification equivalent (e.g. Vehicle Identification Number); and

(B) Place the data elements of the unique item identifier (enterprise identifier; serial number; DoD recognized unique identification equivalent; and for serialization within the part, lot, or batch number only: Original part, lot, or batch number) on items requiring marking by paragraph (c)(1) of this clause, based on the criteria provided in MIL-STD-130, Identification Marking of

U.S. Military Property, latest version;

(C) Label shipments, storage containers and packages that contain uniquely identified items in accordance with the requirements of

MIL-STD-129, Military Marking for Shipment and Storage, latest version; and

(D) Verify that the marks on items and labels on shipments, storage containers, and packages are machine readable and conform to the applicable standards. The contractor shall use an automatic identification technology device for this verification that has been programmed to the requirements of Appendix A, MIL-STD-130, latest version.

(ii) The issuing agency code--

(A) Shall not be placed on the item; and

(B) Shall be derived from the data qualifier for the enterprise identifier.

(d) For each item that requires item unique identification under paragraph (c)(1)(i), (ii), or (iv) of this clause or when item unique identification is provided under paragraph (c)(1)(v), in addition to the information provided as part of the Material Inspection and

Receiving Report specified elsewhere in this contract, the Contractor shall report at the time of delivery, as part of the Material

Inspection and Receiving Report, the following information:

(1) Unique item identifier.

(2) Unique item identifier type.

(3) Issuing agency code (if concatenated unique item identifier is used).

(4) Enterprise identifier (if concatenated unique item identifier is used).

(5) Original part number (if there is serialization within the original part number).

(6) Lot or batch number (if there is serialization within the lot or batch number).

(7) Current part number (optional and only if not the same as the original part number).

(8) Current part number effective date (optional and only if current part number is used).

(9) Serial number (if concatenated unique item identifier is used).

(10) Governments unit acquisition cost.

(11) Unit of measure.

(12) Type designation of the item as specified in the contract schedule, if any.

19 69

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

(13) Whether the item is an item of Special Tooling or Special Test Equipment.

(14) Whether the item is covered by a warranty.

(e) For embedded subassemblies, components, and parts that require DoD item unique identification under paragraph (c)(1)(iii) of this clause or when item unique identification is provided under paragraph (c)(1)(v), the Contractor shall report as part of the Material

Inspection and Receiving Report specified elsewhere in this contract, the following information:

(1) Unique item identifier of the parent item under paragraph (c)(1) of this clause that contains the embedded subassembly, component, or part.

(2) Unique item identifier of the embedded subassembly, component, or part.

(3) Unique item identifier type.**

(4) Issuing agency code (if concatenated unique item identifier is used).**

(5) Enterprise identifier (if concatenated unique item identifier is used).**

(6) Original part number (if there is serialization within the original part number).**

(7) Lot or batch number (if there is serialization within the lot or batch number).**

(8) Current part number (optional and only if not the same as the original part number).**

(9) Current part number effective date (optional and only if current part number is used).**

(10) Serial number (if concatenated unique item identifier is used).**

(11) Description.

** Once per item.

(f) The Contractor shall submit the information required by paragraphs (d) and (e) of this clause as follows:

(1) End items shall be reported using the receiving report capability in Wide Area WorkFlow (WAWF) in accordance with the clause at

252.232-7003. If WAWF is not required by this contract, and the contractor is not using WAWF, follow the procedures at http://dodprocurementtoolbox.com/site/uidregistry/ .

(2) Embedded items shall be reported by one of the following methods--

(i) Use of the embedded items capability in WAWF;

(ii) Direct data submission to the IUID Registry following the procedures and formats at http://dodprocurementtoolbox.com/site/uidregistry/ ; or

(iii) Via WAWF as a deliverable attachment for exhibit line item number N/A, Unique Item Identifier Report for Embedded Items, Contract Data Requirements List, DD Form 1423.

(g) Subcontracts. If the Contractor acquires by subcontract any item(s) for which item unique identification is required in accordance with paragraph (c)(1) of this clause, the Contractor shall include this clause, including this paragraph (g), in the applicable subcontract(s), including subcontracts for commercial products or commercial services.

(End of clause)

20 69

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

SECTION G - CONTRACT ADMINISTRATION DATA

Regulatory Cite Title Date Regulatory Cite Title Date _______________ ______________________________________________________________________ ____________ _______________ ______________________________________________________________________ ____________

G-1 252.232-7006 WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023) JAN/2023

(a) Definitions. As used in this clause--

"Department of Defense Activity Address Code (DoDAAC)" is a six position code that uniquely identifies a unit, activity, or organization.

"Document type" means the type of payment request or receiving report available for creation in Wide Area WorkFlow (WAWF).

"Local processing office (LPO)" is the office responsible for payment certification when payment certification is done external to the entitlement system.

"Payment request" and "receiving report" are defined in the clause at 252.232-7003, Electronic Submission of Payment Requests and

Receiving Reports.

(b) Electronic invoicing. The WAWF system provides the method to electronically process vendor payment requests and receiving reports, as authorized by Defense Federal Acquisition Regulation Supplement (DFARS) 252.232-7003, Electronic Submission of Payment Requests and

Receiving Reports.

(c) WAWF access. To access WAWF, the Contractor shall--

(1) Have a designated electronic business point of contact in the System for Award Management at https://www.sam.gov ; and

(2) Be registered to use WAWF at https://wawf.eb.mil/ following the step-by-step procedures for self-registration available at this Web site.

(d) WAWF training. The Contractor should follow the training instructions of the WAWF Web-Based Training Course and use the Practice

Training Site before submitting payment requests through WAWF. Both can be accessed by selecting the "Web Based Training" link on the

WAWF home page at https://wawf.eb.mil/ .

(e) WAWF methods of document submission. Document submissions may be via Web entry, Electronic Data Interchange, or File Transfer

Protocol.

(f) WAWF payment instructions. The Contractor shall use the following information when submitting payment requests and receiving reports in WAWF for this contract or task or delivery order:

(1) Document type. The Contractor shall submit payment requests using the following document type(s):

(i) For cost-type line items, including labor-hour or time-and-materials, submit a cost voucher.

(ii) For fixed price line items--

(A) That require shipment of a deliverable, submit the invoice and receiving report specified by the…