SALIENT CHARACTERISTICS.pdf

PDF 209 KB Posted

Attached to
HYDRAULIC PUMP PACKAGE Federal contract opportunity
Solicitation number
SPMYM223Q1675
Issued by
Defense Logistics Agency Land and Maritime

About this file

Written by GovTribe AI ·

This document outlines the salient characteristics for a heat exchanger tool kit solicitation. The solicitation requires a heat exchanger tool kit from Elliott Tool Technologies or equal, including a super collet tube puller with specified pulling capacity and stroke, hydraulic pump, counter balances, collets, draw bars, tie rods, nose piece, drive motor, tube cutter with specified blade width gauge range, cutter blades, cutter pin, electrical rolling motor, and electric torque controller. The kit must also include national recognized testing laboratory safety certification for all equipment and components to comply with applicable Occupational Safety and Health Administration regulations.

The related federal contract opportunity is solicitation number SPMYM223Q1675 for a hydraulic pump package from the Defense Logistics Agency Land and Maritime. The document provides the requirements for a heat exchanger tool kit and hydraulic pump package solicitation from the Defense Logistics Agency Land and Maritime.

View the file

Other files for this federal contract opportunity

Other files attached to HYDRAULIC PUMP PACKAGE, newest first.
File Type Posted
SPMYM2-23-Q-1675.pdf PDF

On GovTribe

Work with this file on GovTribe

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file
Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

Salient Characteristics for a Heat Exchanger Tool Kit

Project #147-320 28 Jun 23

1. Heat Exchanger Tool Kit Requirements (Elliott Tool Technologies, Super Collet Tube Puller or equal) to include the following:

a. One (1) - Super Collet Tube Puller (Elliott Tool Technologies, Part #CPS15 or equal). Package includes pulling head, two hydraulic hoses, and safety deflector shield. Pulling Capacity: up to 15 Tons. Pulling Stroke: 6" (152.44mm).

b. One (1) 110V Hydraulic Pump. (Elliott Tool Technologies, Part #M5773-00 or equal).

Includes: HP: 1.13, 10,000PSI Max Operating Pressure, Power Requirement: 25 Amps.

c. Three (3) Counter Balance (Elliott Tool Technologies, Part #TCB48-66 or equal).

d. Three (3) Collet16 -18 BWG (Elliott Tool Technologies, Part # CPC625-16 or equal).

e. Three (3) Draw Bar (Elliott Tool Technologies, Part # CPD625 or equal).

f. Three (3) Tie Rod (Elliott Tool Technologies, Part # CPT625 or equal).

g. One (1) Nose Piece (Elliott Tool Technologies, Part # CPN625 or equal).

h. One (1) Drive Motor (Elliott Tool Technologies, Part # 447000 or equal).

i. One (1) 5/8" x 16-22, PTTC Series Tube Cutter. (Elliott Tool Technologies, Part #PTTC625K12 or equal). Includes: Tube Cutter, Cutter Blades with Pin, and Tube Cutter Pilots.

BWG Range: 16-22 C

j. Three (3) Cutter Blade With Pin (Elliott Tool Technologies, Part # PTTC25186 or equal).

k. One (1) Cutter Pin (Elliott Tool Technologies, Part # PTTC625CP or equal).

l. One (1) 99 Series Electrical Rolling Motor (Elliott Tool Technologies, Part # 99150-110-7P or equal).

m. One (1) Electric Torque Controller (Elliott Tool Technologies, Part # ELC110220 or equal).

Includes: Electric Controller Unit and (1) 110V North American (Nema 5-15) Power Cord.

n. One (1) NRTL Safety Certification

i. Nationally Recognized Testing Laboratory (NRTL) certification performed by an OSHA authorized third party (as outlined in Paragraph 2 below)

2. NRTL Safety Certification Requirements:

a. The equipment and its component parts shall be in compliance with applicable Code of Federal Regulations (CFR) Title 29, Part 1910. By definition, any equipment will be deemed acceptable and approved by TRF, Bangor, if it meets specific Occupational Safety and Health Administration (OSHA) conditions outlined in CFR Title 29, Part 1910; Subparts "O" and "S".

Specifically, equipment will be "Accepted" by TRF, Bangor, if it has been inspected and found by a Nationally Recognized Testing Laboratory (NRTL) to conform to specified plans or procedures of applicable codes. The equipment (as a whole system) shall be Nationally Recognized Testing Laboratory (NRTL) inspected and certified (by an OSHA authorized third party). One “hard” copy for each paint mixers/shaker of the NRTL certification report shall be provided. If the equipment type/model has already been NRTL inspected and certified, a certification report (one “hard” copy for each paint mixer/shaker shall be provided) or sticker documentation mounted on the equipment, (which acknowledges it is NRTL certified), shall be provided.

Salient Characteristics for a
Heat Exchanger Tool Kit
1. Heat Exchanger Tool Kit Requirements (Elliott Tool Technologies, Super Collet Tube Puller or equal) to include the following:
a. One (1) - Super Collet Tube Puller (Elliott Tool Technologies, Part #CPS15 or equal). Package includes pulling head, two hydraulic hoses, and safety deflector shield. Pulling Capacity: up to 15 Tons. Pulling Stroke: 6" (152.44mm).
b. One (1) 110V Hydraulic Pump. (Elliott Tool Technologies, Part #M5773-00 or equal). Includes: HP: 1.13, 10,000PSI Max Operating Pressure, Power Requirement: 25 Amps.
c. Three (3) Counter Balance (Elliott Tool Technologies, Part #TCB48-66 or equal).
d. Three (3) Collet16 -18 BWG (Elliott Tool Technologies, Part # CPC625-16 or equal).
e. Three (3) Draw Bar (Elliott Tool Technologies, Part # CPD625 or equal).
f. Three (3) Tie Rod (Elliott Tool Technologies, Part # CPT625 or equal).
g. One (1) Nose Piece (Elliott Tool Technologies, Part # CPN625 or equal).
h. One (1) Drive Motor (Elliott Tool Technologies, Part # 447000 or equal).
i. One (1) 5/8" x 16-22, PTTC Series Tube Cutter. (Elliott Tool Technologies, Part #PTTC625K12 or equal). Includes: Tube Cutter, Cutter Blades with Pin, and Tube Cutter Pilots. BWG Range: 16-22 C
j. Three (3) Cutter Blade With Pin (Elliott Tool Technologies, Part # PTTC25186 or equal).
k. One (1) Cutter Pin (Elliott Tool Technologies, Part # PTTC625CP or equal).
l. One (1) 99 Series Electrical Rolling Motor (Elliott Tool Technologies, Part # 99150-110-7P or equal).
m. One (1) Electric Torque Controller (Elliott Tool Technologies, Part # ELC110220 or equal). Includes: Electric Controller Unit and (1) 110V North American (Nema 5-15) Power Cord.
n. One (1) NRTL Safety Certification

File details come from the government source that posted it. Updated .