RFI-01_8-28-2017_GarnierGroup.pdf

USP Lewisburg, PA (Replace Microwave System)_RFI-01_8-28-2017 (Garnier Group) Q #01 – SOW section 1.01 Description, A, 1 (installation by others) – Are the installers Senstar certified?

Yes

Q #02 – SOW section 1.01 Description, A, 1 b. (36) Thirty‐six Comm Cards – Is it the desire of the Owner to have 3 spare Comm Cards or this this a typo and should actually be (33) matching the transmitter and receiver pair quantity? 3 Spare

Q #03 ‐ SOW section 1.01 Description, A, 1 d. (3) Three 480W, 48Vdc din rail Power Supply – Are these to supplement the existing microwave power supplies to be re‐used or should this be (35)? (See below) (Each transmitter and receiver pair requires power to each unit and typically if it is not physically possible to power overlapped pairs from one power supply they would require two (2) physical power supplies, and for this application presuming the perimeter to be covered by the microwaves is contiguous then potentially (35) new power supplies would be required to cover the 33 pairs from where they overlap and then for the beginning and ending microwaves). Supplement existing

Q #04 ‐ SOW section 1.01 Description, A, 1 d. (3) Three 480W, 48Vdc din rail Power Supply –Are the power supplies to be mounted indoors or outdoors? (If outdoors a separate outdoor rated enclosure will be required). Indoors

Q #05 ‐ SOW section 1.01 Description, A, 1 g. (1) One FlexZone‐ 4 processor – There is no Comm Card listed for the FlexZone Processor in this section, and presume it would also need to be MMFO, is this an oversight or is it covered in the quantity of (36) listed in subsection b as noted above? Covered in quantity of 36

Q #06 ‐ SOW section 1.01 Description, A, 1 g. (1) One FlexZone‐ 4 processor – It is recommended to have splice kits on hand as spares should there be damage repair necessary after installation, would the Owner agree to having two kits included in the Proposal? Yes

Q #07 ‐ SOW section 1.01 Description, A, 1 i. (1) One Flexzone cable terminator – It is recommended to have two terminator kits per cable side, should something happen during or after installation, would the Owner agree to having two kits included in the Proposal? Yes

Q #08 – SOW section 1.01 Description, A, 1 m. (2) Two Equal to or same as StarNet 2 hardware & software 2‐station bundles: ‐ Is it the intent to set up one StarNet2 bundle and hold the other one as a spare? No

Q #09 – SOW section 1.01 Description, A, 1 m. (2) Two Equal to or same as StarNet 2 hardware & software 2‐station bundles: If answer to Q #08 is no, then there is a more economical way to purchase a

(4) workstation and 1 server bundle, would the Owner prefer that as opposed to the (2) StarNet2 Bundles? No

Q #10 – SOW section 1.01 Description, A, 1 t. ‐ Provide onsite training. – Is this requirement intended to be for end users only or for the installation technicians as well? Both

Q #11 –General – Senstar offers a rack/cabinet mountable 4U UltraLink swing‐out DIN rail, and is recommending 2 each, would the Owner want these to be included in the equipment solution or will all DIN rail devices be wall mounted? Yes

Q #12 – General – There are no spares called out in the SOW, and it would be recommend to have at least one or two spare UltraWave processor boards and possibly one FlexZone processor board on hand, would the Owner want spare system processor boards included in the Proposal? No