Atttachment_2c_Drawings_Ref'd_in_BOMs_(Rev2).pdf

Attachment 2.c Chassis Cable Drawings Rev 2

RA133W16RQ0510

CAGE CODE 0WY55 DWG NO. 2200036 SHEET 1 OF 5

APPLICATION

NHA USED ON LTR DATE CO ECP O/A REVISION DESCRIPTION APVD

2320006

2320007

2320010

2320011

2320012

WSR-88D

VENDOR ITEM DRAWING

DISTRIBUTION STATEMENT: A: Approved for public release; distribution is unlimited.

DOC/DOD/DOT

WSR-88D RADAR OPERATIONS CENTER

3200 MARSHALL AVENUE

NORMAN, OKLAHOMA 73072

NOMENCLATURE

CABLE, MULTI-PAIRED, INDIVIDUALLY

FOIL SHIELDED

APPROVALS

DWN BOB 980519 LOG NEB 981210

CHK AWB 980519 DOC PJG 981210

ENGR RMM 981210 CM RWH 981210

QA DR 981210 OSF ELB 981210

SIZE CAGE CODE DWG NO. REV

A 0WY55 2200036 -

SCALE NONE SHEET 1 OF 5

CAGE CODE 0WY55 DWG NO. 2200036 SHEET 2 OF 5

GENERAL

1 INTERPRET THIS DRAWING IN ACCORDANCE W ITH MIL-STD-100.

2 IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY CONTAINED IN THIS SPECIFICATION IS NOT TO

BE CONSTRUED AS A GUARANTEE OF PRESENT OR FUTURE AVAILABILITY AS A SOURCE OF SUPPLY FOR

THE ITEM(S).

3 REQUIREM ENTS:

3.1 CONFIGURATION: THE CABLES SPECIFIED IN THIS DRAWING ARE COMMERCIAL TYPE, MULTI-PAIRED, INDIVIDUALLY SHIELDED, UL2919, NEC TYPE CM , CSA PCC.

3.2 CONSTRUCTION:

3.2.1 CONDUCTO R: 22 AW G FULLY ANNEALED STRANDED TINN ED COPPER PER ASTM B-33, TWISTED PAIRS.

SEE T ABLE I.

3.2.2 INSULATION: PREM IUM GRADE COLOR CODED POLYET HYLENE. SEE T ABLE I I.

3.2.3 SHIELD: INDIVIDU ALLY SHIELDED PAIRS. 100% FLEXFOIL® ALUM INUM/POLYESTER 25% OVERLAP, FOIL

FACING IN. STRANDED TINNED COPPER DRAIN WIRE EACH PAIR.

3.2.4 JACKET: PVC, GRAY. TEMPERAT URE RANGE -20°C TO +80° C.

3.3 IDENTIFICATION: VENDOR IDENTIFICATION AND VENDOR PART NUMB ER TO BE APPLIED BY VEN DOR.

TABLE I

DETAILS

DASH

NO.

CONDUCTOR

SIZE

NUMBER

OF PAIRS

CONDUCTOR

STRANDING

NOMINAL

INSULATION

THICKNESS

NOMINAL

CABLE JACKET

THICKNESS

OVERALL

DIAMETER

201 22 AWG 6 7/30 .011 .032 .381

202 22 AWG 9 7/30 .011 .032 .445

203 22 AWG 19 7/30 .011 .048 .622

DIMENSIONS ARE IN INCHES

SIZE CAGE CODE DWG NO. REV

SCALE NONE SHEET 2 OF 5

CAGE CODE 0WY55 DWG NO. 2200036 SHEET 3 OF 5

TAB LE II

COLOR CODE CHART

NO. OF

PAIRS

COLOR

1 BLACK PAIRED WITH RED

2 BLACK PAIRED WITH WHITE

3 BLACK PAIRED WITH GREEN

4 BLACK PAIRED WITH BLUE

5 BLACK PAIRED WITH YELLOW

6 BLACK PAIRED WITH BROWN

7 BLACK PAIRED WITH ORANGE

8 RED PAIRED WITH WHITE

9 RED PAIRED WITH GREEN

10 RED PAIRED WITH BLUE

11 RED PAIRED WITH YELLOW

12 RED PAIRED WITH BROWN

13 RED PAIRED WITH ORANGE

14 GREEN PAIRED WITH WHITE

15 GREEN PAIRED WITH BLUE

16 GREEN PAIRED WITH YELLOW

17 GREEN PAIRED WITH BROWN

18 GREEN PAIRED WITH ORANGE

19 WHITE PAIRED WITH BLUE

SIZE CAGE CODE DWG NO. REV

SCALE NONE SHEET 3 OF 5

CAGE CODE 0WY55 DWG NO. 2200036 SHEET 4 OF 5

FIGURE 1

SIZE CAGE CODE DWG NO. REV

SCALE NONE SHEET 4 OF 5

CAGE CODE 0WY55 DWG NO. 2200036 SHEET 5 OF 5

SUGGESTED SOURCE(S) OF SUPPLY

GENERAL CABLE CORPORATION (CAGE CODE 1E251)

HIGHLAND HEIGHTS, KY

PART NO.: PER TAB LE III

TAB LE III

DASH

NO.

GENERAL CABLE

PART NUMBER

201 C6041

202 C6042

203 C6045

SIZE CAGE CODE DWG NO. REV

SCALE NONE SHEET 5 OF 5

CAGE CODE 0WY55 DWG NO. 2200037 SHEET 1 of 6

SIZE CAGE CODE DWG NO. REV

A 0WY55 2200037 -

SCALE NONE SHEET 1 OF 6

APPLICATION

NHA USED ON LTR DATE CO ECP O/A REVISION DESCRIPTION APVD

2320006

MULTIPLE

WSR-88D

VENDOR ITEM DRAWING

DISTRIBUTION STATEMENT: A: Approved for public release; distribution is unlimited.

DOC/DOD/DOT

WSR-88D RADAR OPERATIONS CENTER

3200 MARSHALL AVENUE

NORMAN, OKLAHOMA 73072

NOMENCLATURE

CONNECTOR, RECEPTACLE ASSEMBLY,

SERIES 1

APPROVALS

DWN BOB 980610 LOG NEB 981210

CHK AWB 980610 DOC PJG 981210

ENGR RMM 981210 CM RWH 981210

QA DR 981210 OSF ELB 981210

CAGE CODE 0WY55 DWG NO. 2200037 SHEET 2 of 6

A 0WY55 2200037 -

SCALE NONE SHEET 2 OF 6

GENERAL

1 INTERPRET THIS DRAWING IN ACCORDANCE W ITH MIL-STD-100.

2 IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY CONTAINED IN THIS SPECIFICATION IS NOT TO

BE CONSTRUED AS A GUARANTEE OF PRESENT OR FUTURE AVAILABILITY AS A SOURCE OF SUPPLY FOR

THE ITEM(S).

3 REQUIREM ENTS:

3.1 STYLE: CIRCULAR MIL-C-5015 STYLE CONNECTOR, RECEPTACLE.

3.2 OUTLINE: PER FIGURE 1 AND TAB LE I.

3.3 INSERT ARRANGEMENTS: PER FIGURES 2, 3 AND TABLE I

3.4 MATERIAL AND FINISH

3.4.1 SHELL: ZINC ALLOY, NICKEL PLATED PER QQ-N-290

3.4.2 HOUSING: THERMOPLASTIC, COLOR BLACK, UL 94V-0 RATED

3.5 VOLTAGE RATING:

3.6 TEM PERATU RE RATING: -55° TO +125°

3.7 IDENT IFICATION : VENDOR IDENT IFICATION AND VENDOR PART NUM BER TO BE APPLIED BY VENDOR.

4 APPLICATION DATA

4.1 USED W ITH PIN CON TACTS ON 0W Y55-2200039

5 THE PART NUMBER IS THE DRAWING NUMBER SUFFIXED WITH THE APPLICABLE DASH NUMBER SHOWN

IN TABLE II.

CAGE CODE 0WY55 DWG NO. 2200037 SHEET 3 of 6

A 0WY55 2200037 -

SCALE NONE SHEET 3 OF 6

FIGURE 1

TABLE I

DIMENSIONS

DASH

NO.

DIM

A

DIM

B

± .010

DIM

C

± .010

DIA

D

DIM

E

± .005

DIM

F

± .015

SHELL THREAD

SIZE

INSERT

ARRANGEMENT

1.555

MAX

.875 .125

1.900

MAX

1.562 1.950 1-3/8 - 18 UNEF-2A FIGURE 2

1.470

MAX

.790 .100

1.503

MAX

1.250 1.534 15/16 - 20 UNEF-2A FIGURE 3

DIMENSIONS ARE IN INCHES

CAGE CODE 0WY55 DWG NO. 2200037 SHEET 4 of 6

A 0WY55 2200037 -

SCALE NONE SHEET 4 OF 6

FIGURE 2

-201 CONFIGURATION

CAGE CODE 0WY55 DWG NO. 2200037 SHEET 5 of 6

A 0WY55 2200037 -

SCALE NONE SHEET 5 OF 6

FIGURE 3

-202 CONFIGURATION

CAGE CODE 0WY55 DWG NO. 2200037 SHEET 6 of 6

A 0WY55 2200037 -

SCALE NONE SHEET 6 OF 6

SUGGESTED SOURCE(S) OF SUPPLY

AMP INCORPORATED (CAGE CODE 00779)

HARRISBURG, PA 17105

PART NO.: PER TAB LE II

TAB LE II

DASH

NO.

AMP

PART

NUMBER

SHELL

SIZE

201 208459-1 28

202 208489-1 22

CAGE CODE 0WY55 DWG NO. 2200038 SHEET 1 of 4

A 0WY55 2200038 -

SCALE NONE SHEET 1 OF 4

APPLICATION

NHA USED ON LTR DATE CO ECP O/A REVISION DESCRIPTION APVD

2320006

MULTIPLE

WSR-88D

VENDOR ITEM DRAWING

DISTRIBUTION STATEMENT: A: Approved for public release; distribution is unlimited.

DOC/DOD/DOT

WSR-88D RADAR OPERATIONS CENTER

3200 MARSHALL AVENUE

NORMAN, OKLAHOMA 73072

NOMENCLATURE

CLAMP CABLE, STANDARD, CPC

APPROVALS

DWN BOB 980623 LOG NEB 981210

CHK AWB 980623 DOC PJG 981210

ENGR RMM 981210 CM RWH 981210

CAGE CODE 0WY55 DWG NO. 2200038 SHEET 2 of 4

A 0WY55 2200038 -

SCALE NONE SHEET 2 OF 4

1 INTERPRET THIS DRAWING IN ACCORDANCE W ITH MIL-STD-100.

2 IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY CONTAINED IN THIS SPECIFICATION IS NOT TO

BE CONSTRUED AS A GUARANTEE OF PRESENT OR FUTURE AVAILABILITY AS A SOURCE OF SUPPLY FOR

THE ITEM(S).

3 REQUIREM ENTS:

3.1 OUTLINE: PER FIGURE 1 AND TAB LE I.

3.2 MAXIMUM CABLE DIAMETER: -201 .453 INCH

-202 .703 INCH

3.3 MATERIAL: THERMOPLASTIC, COLOR BLACK, UL 94V-1 RATED

3.4 IDENT IFICATION : VENDOR IDENT IFICATION AND VENDOR PART NUM BER TO BE APPLIED BY VENDOR.

4 APPLICATION DATA

4.1 USED W ITH CONNECTORS ON 0W Y55-2200037

CAGE CODE 0WY55 DWG NO. 2200038 SHEET 3 of 4

A 0WY55 2200038 -

SCALE NONE SHEET 3 OF 4

DIMENSIONS ARE IN INCHES

FIGURE 1

TABLE I

DIMENSIONS

DASH

NO.

DIAMETER

A

DIM

B

THREAD SIZE

201 1.125 ± .025 1.400 ± .030 15/16 - 20 UNEF-2B

202 1.600 ± .025 1.555 ± .030 1-3/8 - 18 UNEF-2B

SUGGESTED SOURCE(S) OF SUPPLY

AMP INCORPORATED (CAGE CODE 00779)

CAGE CODE 0WY55 DWG NO. 2200038 SHEET 4 of 4

A 0WY55 2200038 -

SCALE NONE SHEET 4 OF 4

HARRISBURG, PA 17105

PART NO.: PER TAB LE II

TAB LE II

DASH

NO.

AMP PART NUMBER

201 206070-1

202 206138-1

CAGE CODE 0WY55 DWG NO. 2200039 SHEET 1 OF 3

NHA USED ON LTR DATE CO ECP O/A REVISION DESCRIPTION APVD

2320006

MULTIPLE

WSR-88D

VENDOR ITEM DRAWING

DISTRIBUTION STATEMENT: A: Approved for public release; distribution is unlimited.

DOC/DOD/DOT

WSR-88D RADAR OPERATIONS CENTER

3200 MARSHALL AVENUE

NORMAN, OKLAHOMA 73072

NOMENCLATURE

CONTACT, PIN, CIRCULAR CONNECTORS

APPROVALS

DWN BOB 980610 LOG NEB 981210

CHK AWB 980610 DOC PJG 981210

ENGR RMM 981210 CM RWH 981210

QA DR 981210 OSF ELB 981210

SIZE CAGE CODE DWG NO. REV

A 0WY55 2200039 -

SCALE NONE SHEET 1 OF 3

CAGE CODE 0WY55 DWG NO. 2200039 SHEET 2 OF 3

1. INTERPRET THIS DRAWING IN ACCORDANCE W ITH MIL-STD-100.

2. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY CONTAINED IN THIS SPECIFICATION IS NOT TO

BE CONSTRUED AS A GUARANTEE OF PRESENT OR FUTURE AVAILABILITY AS A SOURCE OF SUPPLY FOR

THE ITEM(S).

3. REQUIREM ENTS:

3.1 STYE: CRIM P REMO VAB LE, PRECISION FORMED, PIN (MALE) CONTACT, SIZE 16, USED IN

COMMERCIAL CPC (CIRCULAR PLASTIC) AND METAL SHELL CONNECTORS (AMP INCORPORATED

OR EQUIVALENT).

3.2 OUTLINE VIEW: PER FIGURE 1 AND TABLE I

3.3 WIRE ACCOM MO DAT ION: PER TABLE I

3.4 MATERIAL: BRASS

3.5 FINISH: BRIGHT TIN-LEAD

3.6 CURRENT RATING: 13 AMPS

3.7 IDENTIFICATION: VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY

VENDOR.

4. THE PART NU MBER IS THE DRAW ING NUMB ER SUFFIXED WITH THE APPLICABLE DASH NUM BER AS

SHOWN IN T ABLE I.

SIZE CAGE CODE DWG NO. REV

SCALE NONE SHEET 2 OF 3

CAGE CODE 0WY55 DWG NO. 2200039 SHEET 3 OF 3

APPROVED SOURCES OF SUPPLY:

AMP INCORPORATED (CAGE CODE 00779)

HARRISBURG, PA 17105

PART NUMBER: PER TABLE I

TABLE I

DASH

NO.

CONTACT

SIZE

WIRE

ACCOMMODATIONS (AWG)

AMP PART

NO.

201 16 20, 22, 24 66103-2

DIMENSIONS ARE IN INCHES

FIGURE 1

SIZE CAGE CODE DWG NO. REV

SCALE NONE SHEET 3 OF 3

CAGE CODE 0WY55 DWG NO. 2200040 SHEET 1 of 5

A 0WY55 2200040 -

SCALE NONE SHEET 1 OF 5

APPLICATION

NHA USED ON LTR DATE CO ECP O/A REVISION DESCRIPTION APVD

2320006

MULTIPLE

WSR-88D

VENDOR ITEM DRAWING

DISTRIBUTION STATEMENT: A: Approved for public release; distribution is unlimited.

DOC/DOD/DOT

WSR-88D RADAR OPERATIONS CENTER

3200 MARSHALL AVENUE

NORMAN, OKLAHOMA 73072

NOMENCLATURE

CONNECTOR, RECEPTACLE ASSEMBLY,

SERIES II

APPROVALS

DWN BOB 981123 LOG NEB 981210

CHK AWB 981123 DOC PJG 981210

CAGE CODE 0WY55 DWG NO. 2200040 SHEET 2 of 5

A 0WY55 2200040 -

SCALE NONE SHEET 2 OF 5

GENERAL

1 INTERPRET THIS DRAWING IN ACCORDANCE W ITH MIL-STD-100.

2 IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY CONTAINED IN THIS SPECIFICATION IS NOT TO

BE CONSTRUED AS A GUARANTEE OF PRESENT OR FUTURE AVAILABILITY AS A SOURCE OF SUPPLY FOR

THE ITEM(S).

3 REQUIREM ENTS:

3.1 STYLE: CIRCULAR MIL-C-5015 STYLE CONNECTOR, RECEPTACLE.

3.2 OUTLINE: PER FIGURE 1 AND TAB LE I.

3.3 INSERT ARRANGEMENTS: PER FIGURE 2 AND TABLE I

3.4 MATERIAL AND FINISH

3.4.1 SHELL: ZINC ALLOY, NICKEL PLATED PER QQ-N-290

3.4.2 HOUSING: THERMOPLASTIC, COLOR BLACK, UL 94V-0 RATED

3.5 VOLTAGE RATING:

3.6 TEM PERATU RE RATING: -55° TO +125°

3.7 IDENT IFICATION : VENDOR IDENT IFICATION AND VENDOR PART NUM BER TO BE APPLIED BY VENDOR.

4 APPLICATION DATA

4.1 USED W ITH PIN CON TACTS ON 0W Y55-2200049

CAGE CODE 0WY55 DWG NO. 2200040 SHEET 3 of 5

A 0WY55 2200040 -

SCALE NONE SHEET 3 OF 5

FIGURE 1

TABLE I

DIMENSIONS

DASH

NO.

DIM

A

DIM

B

± .010

DIM

C

± .010

DIA

D

DIM

E

± .005

DIM

F

± .015

SHELL THREAD

SIZE

INSERT

ARRANGEMENT

1.229

MAX

.875 .125

1.900

MAX

1.562 1.950 1-3/8 - 18 UNEF-2A FIGURE 2

CAGE CODE 0WY55 DWG NO. 2200040 SHEET 4 of 5

A 0WY55 2200040 -

SCALE NONE SHEET 4 OF 5

FIGURE 2

-201 CONFIGURATION

CAGE CODE 0WY55 DWG NO. 2200040 SHEET 5 of 5

A 0WY55 2200040 -

SCALE NONE SHEET 5 OF 5

SUGGESTED SOURCE(S) OF SUPPLY

AMP INCORPORATED (CAGE CODE 00779)

HARRISBURG, PA 17105

PART NO.: PER TAB LE II

TAB LE II

DASH

NO.

AMP

PART

NUMBER

SHELL

SIZE

201 208477-1 28

CAGE CODE 0WY55 DWG NO. 2200049 SHEET 1 OF 3

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320208 WSR-88D A 061213 ECP 0232

ECO A03010

REPLACE OBSOLETE -201 PART

NUMBER, ADD -202 CONFIGURATION CWF

VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

UNLESS OTHERWISE SPECIFIED

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

3200 MARSHALL AVENUE

NORMAN, OKLAHOMA 73072-8032

NOMENCLATURE

MILLIMETERS

1 PL ±

2 PL ±

ANGLES ± 2°

INCHES

2 PL ±

3 PL ±

APPROVALS

DWN BOB 981124 RMT NEB 981210

CHK AWB 981124 DOC PJG 981210

QA DR 981210 ROC ELB 981210

CONTACT, PIN, SIZE 20 DF, 20-24 AWG, AMPLIMITE

A 0WY55 2200049 A

SCALE: NONE SHEET 1 OF 3

CAGE CODE 0WY55 DWG NO. 2200049 SHEET 2 OF 3

GENERAL NOTES:

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

SPECIFICATION IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR FUTURE AVAILABILITY

AS A SOURCE OF SUPPLY FOR THE ITEM(S).

1.2. THE USE OF A DIFFERENT PART FROM A LISTED SUGGESTED SOURCE OF SUPPLY OR A PART FROM A

NON-LISTED SUGGESTED SOURCE OF SUPPLY WHICH MEETS THE SPECIFICATIONS HEREIN SHALL OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR- 88D RADAR OPERATIONS CENTER (ROC) AS WELL AS ACCEPTANCE INSPECTION BY THE NATIONAL

RECONDITIONING CENTER (NRC).

2. REQUIREMENTS:

2.1. STYLE: CRIMP REMOVABLE, PRECISION FORMED, PIN (MALE) CONTACT, SIZE 20, USED IN

COMMERCIAL CPC (CIRCULAR PLASTIC) AND METAL SHELL CONNECTORS (AMP INCORPORATED OR

EQUIVALENT).

2.2. OUTLINE VIEW: PER FIGURE 1 AND TABLE I.

2.3. WIRE ACCOMMODATION: PER TABLE I.

2.4. MATERIAL: BRASS PER QQ-B-750.

2.5. FINISH: PER TABLE I.

2.6. CURRENT RATING: 13 AMPS.

2.7. PART IDENTIFICATION:

2.7.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

4. THE PART NUMBER IS THE DRAWING NUMBER SUFFIXED WITH THE APPLICABLE DASH NUMBER

SHOWN IN TABLE II.

5. SUGGESTED SOURCE(S) OF SUPPLY (MANUFACTURER(S)):

AMP INCORPORATED (CAGE CODE 00779)

HARRISBURG, PA 17105

PART NO.: PER TABLE I

TABLE I

DASH

NO.

CONTACT

SIZE

WIRE

ACCOMMODATIONS

(AWG)

AMP PART

NUMBER NOTES

201 20 20, 22, 24 1-66506-0* 1, 3

202 20 20, 22, 24 2-66506-5

OR

1658539-2*

2, 4

SCALE: NONE SHEET 2 OF 3

CAGE CODE 0WY55 DWG NO. 2200049 SHEET 3 OF 3

*COMPLIES WITH THE RESTRICTIONS OF CERTAIN HAZARDOUS SUBSTANCES (RoHS) DIRECTIVE.

NOTES:

1. FINISH: PLATED WITH GOLD FLASH OVER 0.76 μm (.000030) NICKEL.

2. FINISH: PLATED WITH GOLD FLASH IN LOCALIZED GOLD PLATE AREA, TIN PLATED WIRE

BARRELS, OVER 0.76 μm (.000030) NICKEL.

3. LOOSE PIECE FOR HAND TOOL USE ONLY.

4. STRIP FOR MINI-APPLICATOR AND STRIPPER CRIMPER.

6. FIGURES AND DIAGRAMS

DIMENSIONS IN INCHES

SCALE: NONE SHEET 3 OF 3

CAGE CODE 0W Y55 DWG NO. 2200083 SHEET 1 of 3

A 0WY55 2200083 A

SCALE NONE SHEET 1 OF 3

APPLICATION

NHA USED ON LTR DATE CO EC P O/A REVISION DESCRIPTION APVD

2320028

MULTIPLE

WSR-88D - 000801 ECP 0103

ECO A00377

INITIAL RELEASE AT REV D.

HORVAT

A 010702 ECP-0103

ECO-A00526

REMOVE LOGISTICS NAME

FROM TITLE BLOCK

ADDED ADDITIONAL PARTS

(-202, & -203)

DH

VENDOR ITEM DRAWING

DISTRIBUTION STATEMENT: A: Approved for public release; distribution is unlimited.

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES

TOLERANCES ON:

DOC/DOD/DOT

WSR-88D RADAR OPERATIONS CENTER

3200 MARSHALL AVENUE

NORM AN, OKL AHOM A 73072-8032

MILLIMETERS INCHES

1 PL 2 PL ± .03

2 PL 3 PL ± .01

ANGLE S ± 2°

APPROVALS NOMENCLATURE

DWN AWB 000801 LOG LABEL, THERMAL TRANSFER

CHK BOB 000801 DOC PJG 000803

ENGR DH 000808 CM

QA OSF

CAGE CODE 0W Y55 DWG NO. 2200083 SHEET 2 of 3

A 0WY55 2200083 A

SCALE NONE SHEET 2 OF 3

GENERAL

1 INTERPRET THIS DRAWING IN ACCO RDANCE WITH M IL-STD-100.

2 IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY CONTAINED IN THIS SPECIFICATION IS NOT TO

BE CONSTRUED AS A GUARANTEE OF PRESENT OR FUTURE AVAILABILITY AS A SOURCE OF SUPPLY FOR

THE ITE M(S).

3 REQUIREMENTS:

3.1 DES CRIP TION : THESE ITEMS ARE BLAN K SELF-LAMINATING LABEL S, MOUNTED ON A ROLL, FOR USE

WITH A W. H. BRADY THERMAL LABEL PRINTER, MODEL 1024 OR EQUIVALENT. THE TOP

PART OF THE LABEL IS WHITE FOR RECEIVING PRINTING. THE BOTTOM PART IS CLEAR

TRANSPARENT AND IS NOT TO BE PRINTED ON. THE MARKERS ARE SUPPLIED ON ONE

SIDE OF T HE P APE R BA CKIN G ON LY. T HES E ITE MS A RE T O BE SUPP LIED IN BU LK O NLY .

3.2 MATERIAL: VINYL, ADHESIVE BACKED

3.3 FINISH: MATTE

3.4 PACKAGING: THESE ITEMS ARE SU PPLIED IN PACK AGES OF CON TINOU S ROLL S, PER TA BLE II.

3.5 PART IDENTIFICATION:

3.5.1 VEN DOR IDEN TIFIC ATIO N AN D VE NDO R PA RT N UM BER TO B E AP PLIE D BY VEN DOR .

4 PROCUREMENT AGENCY:

4.1 THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED NECESSARY

TO BE ASSURED THE PA RTS CONFORM TO THE SPECIFIED REQUIREMENTS.

IN TAB LE II.

CAGE CODE 0W Y55 DWG NO. 2200083 SHEET 3 of 3

A 0WY55 2200083 A

SCALE NONE SHEET 3 OF 3

SUGGESTED SOURCE(S) OF SUPPLY

W. H. BRADY (CAGE CODE 85480)

MILWAUKEE, WI

PART N O.: PER TA BLE II

TABL E II

DASH

NO.

W.H. BRADY

PART

NUMBER

DIM

A

DIM

B

DIM

C

DIM

D

DIM

E

DIM

F

NUMBER

OF LABELS

PER ROW

NUMBER

OF LABELS

PER ROLL

FIGURE

NUMBER

201 THT-9-427-10 1.00 1.437 .50 1.075 1.625 3.35 3 10,000 1

202 THT-10 -427-3 1.00 3.75 1.00 1.075 4.00 3.35 3 3,000 1

203 THT-5-351-10 1.00 .50 .50 1.075 .60 3.35 3 10,000 1

LABEL SHEET CONFIGURATION

CAGE CODE 0WY55 DWG NO. 2200292 SHEET 1 OF 3

A 0WY55 2200292 B

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

1313 HALLEY CIRCLE

NORMAN, OKLAHOMA 73069-8480

MILLIMETERS

1 PL

2 PL

ANGLES 2

INCHES

2 PL

3 PL

NOMENCLATURE

WIRE, HIGH VOLTAGE

APPROVALS

DWN BOB 071105 RMT DMK 071105

CHK AWB 071105 DOC ARC 071105

ENGR WJU 071105 CM

QA ROC

VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320216 WSR-88D A 071105

ECP 0355

ECO A03525

INITIAL RELEASE AT REV A W.U.

B 090520

ECP 0214

ECO A04295

ADD 20KV WIRE W.U.

CAGE CODE 0WY55 DWG NO. 2200292 SHEET 2 OF 3

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR-

2.1. WIRE: 16 AWG, 19/29 STRANDED SILVER PLATED COPPER, NON-SHIELDED.

2.1.1. DC VOLTAGE RATING: PER TABLE II.

2.1.2. MOLDED JACKET: SILICONE BASED MATERIAL (TUFLEX ™)

2.1.3. NOMINAL WIRE DIAMETER: .058

2.1.4. NOMINAL JACKET DIAMETER: .265

2.1.5. WIRE LENGTH: PER TABLE II.

2.2. ENVIRONMENTAL:

2.2.1. OPERATING TEMPERATURE: +10º C (+50° F)

2.2.2. NON-OPERATING TEMPERATURE: -35º C (-31°F) TO +60º C (+140° F)

2.3. RELIABILITY:

2.3.1. MTBF: N/A

2.4. PART IDENTIFICATION:

2.4.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR. PART NUMBER

MAY BE APPLIED TO PACKAGING.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

CAGE CODE 0WY55 DWG NO. 2200292 SHEET 3 OF 3

DEARBORN WIRE AND CABLE, INC. (CAGE CODE: 28105)

WHEELING, IL

PART NO.: PER TABLE II

TABLE II

NO.

DEARBORN WIRE AND CABLE

PART NO.

WIRE LENGTH

DC

VOLTAGE

RATING

201 39X1635-100 100 FT ± 5 FT 35KV

202 39X1635-1000 1000 FT ± 10 FT 35KV

203 39X1620-100 100 FT ± 5 FT 20KV

204 39X1620-1000 1000 FT ± 10 FT 20KV

CAGE CODE 0WY55 DWG NO. 2200293 SHEET 1 OF 3

A 0WY55 2200293 A

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

3200 MARSHALL AVENUE

NORMAN, OKLAHOMA 73072-8032

NOMENCLATURE

MILLIMETERS

1 PL ±

2 PL ±

ANGLES ± 2°

INCHES

2 PL ±

3 PL ±

APPROVALS

DWN BOB 071105 RMT DMK 071105

CHK AWB 071105 DOC ARC 071105

ENGR WJU 071105 CM

QA ROC

SLEEVING, EXPANDABLE, BRAIDED

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320216 WSR-88D A 071105

ECP 0355

ECO A03526

INITIAL RELEASE AT REV A W.U.

CAGE CODE 0WY55 DWG NO. 2200293 SHEET 2 OF 3

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR-

2.1. SLEEVING: BLACK, POLYETHYLENE TEREPHTHALATE, MONOFILAMENT

2.1.1. NOMINAL INSIDE DIAMETER: SEE TABLE II

2.1.2. NOMINAL EXPANDED INSIDE DIAMETER: SEE TABLE II

2.1.3. SLEEVING LENGTH: PER TABLE II.

2.2. ENVIRONMENTAL:

2.2.1. OPERATING TEMPERATURE: +10º C (+50° F)

2.2.2. NON-OPERATING TEMPERATURE: -35º C (-31°F) TO +60º C (+140° F)

2.3. RELIABILITY:

2.3.1. MTBF: N/A

2.4. PART IDENTIFICATION:

2.4.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR. PART NUMBER

MAY BE APPLIED TO PACKAGING.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

CAGE CODE 0WY55 DWG NO. 2200293 SHEET 3 OF 3

SPC TECHNOLOGY (CAGE CODE: 63590)

BENSENVILLE, IL

EXPANSION RANGE

DASH

NO.

SPC TECHNOLOGY

PART NO.

NOMINAL

DIAMETER EXPANSION

MIN

EXPANSION

MAX

SLEEVING

LENGTH

201 8465-0229-BLK .250 .125 .438 100 FT ± 5 FT

202 8465-0231-BLK .500 .250 .750 100 FT ± 5 FT

CAGE CODE 0WY55 DWG NO. 2200368 SHEET 1 OF 3

A 0WY55 2200368 B

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

1313 HALLEY CIRCLE

NORMAN, OKLAHOMA 73069-8480

MILLIMETERS

1 PL

2 PL

ANGLES 2

INCHES

2 PL .02

3 PL .010

WRAP, SPIRAL, FLAME RETARDANT

APPROVALS

DWN AWB 090513 RMT DMK 120305

CHK BOB 120305 DOC MAK 120305

ENGR GSS 120305 CM

QA ROC

VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320223 2320224

WSR-88D

A 120305

ECP 0214

ECO A04286

INITIAL RELEASE GSS

B 151008

ECP 0540

ECO A06590

ADDED -203 TO TABLE II GSS

CAGE CODE 0WY55 DWG NO. 2200368 SHEET 2 OF 3

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR-

2.1. MATERIAL: FLAME RETARDANT POLYETHYLENE.

2.2. OUTLINE: PER FIGURE 1.

2.3. ENVIRONMENTAL:

2.3.1. OPERATING TEMPERATURE: +10º C (+50° F) TO +35º C (+95°F)

2.3.2. NON-OPERATING TEMPERATURE: -35º C (-31°F) TO +60º C (+140° F)

2.4. RELIABILITY:

2.4.1. MTBF: NOT APPLICABLE

2.5. PART IDENTIFICATION:

2.5.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR. PART NUMBER

MAY BE APPLIED TO PACKAGING.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

4. THE PART NUMBER IS THE DRAWING NUMBER SUFFIXED WITH THE APPLICABLE DASH NUMBER

TYCO ELECTRONICS CORPORATION (CAGE CODE 00779)

MIDDLETOWN, PA

NO.

TYCO

PART NO.

DIM “A”

±.015

DIM “B”

±.010

DIM “C”

±.025 201 500004-1 .250 .045 .375 202 500005-1 .500 .062 .500 203 500000-1 .125 .031 .218

CAGE CODE 0WY55 DWG NO. 2200368 SHEET 3 OF 3

CAGE CODE 0WY55 DWG NO. 2200370 SHEET 1 OF 3

A 0WY55 2200370 A

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

1313 HALLEY CIRCLE

NORMAN, OKLAHOMA 73069-8480

MILLIMETERS

1 PL 152.4

2 PL

ANGLES 2

INCHES

2 PL .06

CABLE ASSEMBLY, FIBER OPTIC, DUPLEX, ST TO ST

APPROVALS

DWN AWB 090521 RMT DMK 120307

CHK BOB 120307 DOC MAK 120307

ENGR GSS 120307 CM

QA ROC

VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320229 WSR-88D

A 090521

ECP 0214

ECO A04296

INITIAL RELEASE AT REVISION A GSS

CAGE CODE 0WY55 DWG NO. 2200370 SHEET 2 OF 3

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR-

2.1. FIBER TYPE: MULTIMODE 62.5/125um, ZIPCORD.

2.1.1. FIBER SPECIFICATION:

2.1.1.1. REPEATABILITY: > 500 CYCLES

2.1.1.2. NUMERICAL APERTURE: 0.275° ± 0.015°

2.1.1.3. ATTENUATION (850-nm / 1300-nm): <3.0 / .0 Db/km

2.1.1.4. BANDWIDTH (850-nm / 1300-nm): >250 / >600 MHz*km

2.1.2. MOLDED JACKET: PVC, COLOR OPTIONAL.

2.1.3. MAXIMUM CABLE DIAMETER: .12 INCH EACH CABLE

2.1.4. CABLE LENGTH: PER TABLE II.

2.2. CONNECTORS: FOUR (4) ST DUPLEX CONNECTORS WITH MOLDED STRAIN RELIEF. THE STRAIN

RELIEF SHALL BE COLOR COORDINATED, OR HAVE AT LEAST ONE OF THE PAIRS OF CABLES

IDENTIFIED BY A LETTER, NUMBER, OR LETTER NUMBER COMBINATION FOR EASY IDENTIFICATION.

A PROTECTIVE COVER SHALL BE PROVIDED OVER EACH CONNECTOR.

2.2.1. INSERTION LOSS PER CONNECTOR: < 3dB, TYPICAL 0.25 dB

2.3. OUTLINE: PER FIGURE 1.

2.4. WIRING: STRAIGHT THROUGH.

2.5. ENVIRONMENTAL:

2.5.1. OPERATING TEMPERATURE: -40ºC (-40°F) TO +70ºC (158°F)

2.5.2. NON-OPERATING TEMPERATURE: -40ºC (-40°F) TO +70ºC (158°F)

2.5.3. HUMIDITY RANGE: 5% TO 95% (NON-CONDENSING)

2.5.4. ALTITUDE: UP TO 3000 METERS ABOVE MEAN SEA LEVEL

2.6. RELIABILITY:

CAGE CODE 0WY55 DWG NO. 2200370 SHEET 3 OF 3

2.6.1. MTBF: NOT AVAILABLE

2.7. PART IDENTIFICATION:

2.7.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

4. THE PART NUMBER IS THE DRAWING NUMBER SUFFIXED WITH THE APPLICABLE DASH NUMBER

L-COM INC. (CAGE CODE 43321)

N. ANDOVER, MA

NO.

L-COM

PART NO.

DIM “L” LENGTH

201 FODSTC-01 1 METER (NOMINAL)

202 FODSTC-04 4 METERS (NOMINAL)

NOTE: THE CABLES MAY COME WITH A BRACKET TO CONNECT EACH OF THE PAIRS OF

CONNECTORS TOGETHER. THE BRACKETS MAY BE DISCARDED.

CAGE CODE 0WY55 DWG NO. 2200394 SHEET 1 OF 3

A 0WY55 2200394 A

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

1313 HALLEY CIRCLE

NORMAN, OKLAHOMA 73069-8480

NOMENCLATURE

MILLIMETERS

1 PL

2 PL

ANGLES 2

INCHES

2 PL .06

3 PL .020

APPROVALS

DWN AWB 091221 RMT DTH 091222

CHK BOB 091221 DOC WLT 091222

ENGR DLS 091222 CM

TERMINAL, LUG, CRIMP, INSULATED, SPADE

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320234 2300086

WSR-88D

A 091222

ECP 0220

ECO A04538

INITIAL RELEASE AT REVISION A

D.

SANDER

CAGE CODE 0WY55 DWG NO. 2200394 SHEET 2 OF 3

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR-

2.1. MATERIAL: COPPER WITH PLASTIC BARREL.

2.2. FINISH: ELECTRO-PLATED TIN.

2.3. TERMINAL STYLE: SPADE

2.3.1. CONDUCTOR SIZE: PER TABLE II.

2.4. STUD SIZE: PER TABLE II.

2.5. OUTLINE: PER FIGURE 1.

2.6. ENVIRONMENTAL:

2.6.1. OPERATING TEMPERATURE: +10º C (+50° F) TO +35º C (+95°F)

2.6.2. NON-OPERATING TEMPERATURE: -35º C (-31°F) TO +60º C (+140° F)

2.7. RELIABILITY:

2.7.1. MTBF: NOT APPLICABLE.

2.8. PART IDENTIFICATION:

2.8.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR. PART NUMBER

MAY BE APPLIED TO PACKAGING.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

CAGE CODE 0WY55 DWG NO. 2200394 SHEET 3 OF 3

DIVERSITECH CORP (DEVCO) (CAGE CODE 3CDK8)

DECATUR, GA

NO.

DEVCO

PART NUMBER

WIRE

RANGE

STUD SIZE

201 6227LX 16-14 #8

(SHAPE OF BARREL AND SPADE MAY VARY FROM PICTURE SHOWN)

CAGE CODE 0WY55 DWG NO. 2200395 SHEET 1 OF 3

A 0WY55 2200395 A

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

1313 HALLEY CIRCLE

NORMAN, OKLAHOMA 73069-8480

NOMENCLATURE

MILLIMETERS

1 PL

2 PL

ANGLES 2

INCHES

2 PL .06

3 PL .020

APPROVALS

DWN AWB 091221 RMT DTH 091222

CHK BOB 091221 DOC WLT 091222

ENGR DLS 091222 CM

TERMINAL, LUG, CRIMP, INSULATED, SLIP-ON

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320234 2300086

WSR-88D

A 091222

ECP 0220

ECO A04539

INITIAL RELEASE AT REVISION A

D.

SANDER

CAGE CODE 0WY55 DWG NO. 2200395 SHEET 2 OF 3

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR-

2.1. MATERIAL: COPPER WITH NYLON OR VINYL BARREL.

2.2. FINISH: ELECTRO-PLATED TIN.

2.3. TERMINAL STYLE: SLIP-ON.

2.3.1. CONDUCTOR SIZE: PER TABLE II.

2.4. SLIP-ON TAB SIZE: PER TABLE II.

2.5. OUTLINE: PER FIGURE 1.

2.6. ENVIRONMENTAL:

2.6.1. OPERATING TEMPERATURE: +10º C (+50° F) TO +35º C (+95°F)

2.6.2. NON-OPERATING TEMPERATURE: -35º C (-31°F) TO +60º C (+140° F)

2.7. RELIABILITY:

2.7.1. MTBF: NOT APPLICABLE.

2.8. PART IDENTIFICATION:

2.8.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR. PART NUMBER

MAY BE APPLIED TO PACKAGING.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

CAGE CODE 0WY55 DWG NO. 2200395 SHEET 3 OF 3

DIVERSITECH CORP (DEVCO) (CAGE CODE 3CDK8)

DECATUR, GA

NO.

DEVCO

PART NUMBER

WIRE

RANGE

MATING

TAB SIZE

201 6281LX 16-14 .187

(SHAPE OF BARREL AND SLIP-ON LUG MAY VARY FROM PICTURE SHOWN)

CAGE CODE 0WY55 DWG NO. 2200454 SHEET 1 OF 3

A 0WY55 2200454 A

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

1313 HALLEY CIRCLE

NORMAN, OKLAHOMA 73069-8480

MILLIMETERS

1 PL

2 PL

ANGLES 2

INCHES

2 PL .25

CABLE ASSEMBLY, RF, FORMABLE, COAX

APPROVALS

DWN BOB 121025 RMT DMK 121025

CHK AWB 121025 DOC MAK 121025

ENGR PDK 121025 CM

QA ROC

VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320253 WSR-88D

A 121025

ECP 0612

ECO A05446

INITIAL RELEASE

P.

KRENEK

CAGE CODE 0WY55 DWG NO. 2200454 SHEET 2 OF 3

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR-

2.1. CABLE: FORMABLE COAXIAL CABLE PER PE-SR402FL (FORMABLE VERSION OF RG402U) OR

EQUIVALENT.

2.1.1. INNER CONDUCTOR: SILVER COVERED COPPER CLAD STEEL.

2.1.2. DIELECTRIC: SOLID PTFE.

2.1.3. OUTER SHIELD: COPPER BRAIDED.

2.1.4. CONNECTORS: ONE (1) TYPE N MALE, RIGHT ANGLE AND ONE (1) SMA MALE. CONNECTORS SHALL BE

ASSEMBLED TO CABLE.

2.2. ELECTRICAL:

2.2.1. REQUIRED FREQUENCY RANGE (GHz): D.C. TO 3.0 GHz.

2.2.2. IMPEDANCE: 50 OHMS.

2.2.3. INSERTION LOSS: .55 dB MAX ATTENUATION @ 3.0 GHz.

2.2.4. VSWR: 1,3:1 MAX.

2.2.5. RF LEAKAGE (dB): -60 dB @ 3.0 GHz.

2.3. OUTLINE: PER FIGURE 1.

2.4. ENVIRONMENTAL:

2.4.1. OPERATING TEMPERATURE: +10º C (+50° F) TO +35º C (+95°F)

2.4.2. NON-OPERATING TEMPERATURE: -35º C (-31°F) TO +60º C (+140° F)

2.5. RELIABILITY:

2.5.1. MTBF: N/A

2.6. PART IDENTIFICATION:

2.6.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR. PART NUMBER

MAY BE APPLIED TO PACKAGING.

CAGE CODE 0WY55 DWG NO. 2200454 SHEET 3 OF 3

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

4. THE PART NUMBER IS THE DRAWING NUMBER SUFFIXED WITH THE APPLICABLE DASH NUMBER

PASTERNACK ENTERPRISES (CAGE CODE 53919)

IRVINE, CA

NO.

PASTERNAK

PART NO.

DIM

“L”

201 PE34559-15 15.00 INCHES

CAGE CODE 0WY55 DWG NO. 2200470 SHEET 1 OF 5

A 0WY55 2200470 B

SCALE: NONE SHEET 1 OF 5

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

1313 HALLEY CIRCLE

NORMAN, OKLAHOMA 73069-8480

MILLIMETERS

1 PL

2 PL

ANGLES 2

INCHES

2 PL .020

BACKSHELL, CONNECTOR, STRAIN-RELIEF, D-SUB

APPROVALS

DWN AWB 130619 RMT JBM 130619

CHK BOB 130619 DOC RJG 130619

ENGR RSS 130619 CM

QA ROC

VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320258 WSR-88D

A 130619

ECP 0437

ECO A05717

INITIAL RELEASE RSS

B 160404

ECP 0540

ECO A06855

ADD -202 THRU -204 RSS

CAGE CODE 0WY55 DWG NO. 2200470 SHEET 2 OF 5

SCALE: NONE SHEET 2 OF 5

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR-

2.1. STYLE: D-SUBMINIATURE, SPLIT BACKSHELL WITH TWO (2) #4-40 MALE JACKSCREWS

2.2. OUTLINE VIEW: SEE FIGURES 1 THRU 4

2.3. MATERIAL:

2.3.1. HOUSING: ZINC DIE-CAST

2.3.2. CABLE STRAIN RELIEF: ZINC DIE CAST

2.3.3. JACKSCREWS: STEEL

2.4. FINISH:

2.4.1. HOUSING: NICKEL PLATE

2.4.2. CABLE STRAIN RELIEF: NICKEL PLATE

2.4.3. JACKSCREWS: NICKEL PLATE

2.5. ENVIRONMENTAL:

2.5.1. OPERATING TEMPERATURE: +10º C (+50° F) TO +35º C (+95°F)

2.5.2. NON-OPERATING TEMPERATURE: -35º C (-31°F) TO +60º C (+140° F)

2.6. RELIABILITY:

2.6.1. MTBF: N/A

2.7. PART IDENTIFICATION:

2.7.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR. PART NUMBER

MAY BE APPLIED TO PACKAGING.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

CAGE CODE 0WY55 DWG NO. 2200470 SHEET 3 OF 5

SCALE: NONE SHEET 3 OF 5

FCI USA LLC (CAGE CODE 22526)

ETTERS, PA

PART NO.: PER TABLE II

MOUSER ELECTRONICS INC (CAGE CODE: 0ZQ52)

MANSFIELD, TX

PART NO.: PER TABLE II

NEWARK ELECTRONICS CORP (CAGE CODE: 02929)

CHICAGO, IL

NO.

FCI

PART NO.

MOUSER

PART NO.

NEWARK

PART NO.

FIGURE

NO.

201 8655MH2511LF 649-8655MH2511LF 63K0610 1

202 8655MH0911LF 649-8655MH0911LF 63K0606 2

203 8655MH1511LF 649-8655MH1511LF 63K0608 3

204 8655MH3711LF 649-8655MH3711LF 63K0612 4

FIGURE 1 (-201)

DIMENSIONS IN BRACKETS ARE METRIC

CAGE CODE 0WY55 DWG NO. 2200470 SHEET 4 OF 5

SCALE: NONE SHEET 4 OF 5

FIGURE 2 (-202)

FIGURE 3 (-203)

CAGE CODE 0WY55 DWG NO. 2200470 SHEET 5 OF 5

SCALE: NONE SHEET 5 OF 5

FIGURE 4 (-204)

CAGE CODE 0WY55 DWG NO. 2200476 SHEET 1 OF 3

A 0WY55 2200476 B

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

3200 MARSHALL AVENUE

NORMAN, OKLAHOMA 73072-8032

MILLIMETERS

1 PL

2 PL

ANGLES 2

INCHES

SLEEVING, NYLON, EXPANDABLE, BRAIDED

APPROVALS

DWN AWB 130702 RMT JBM 130702

CHK BOB 130702 DOC RJG 130702

ENGR RSS 130702 CM

QA ROC

VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320255 2320256

WSR-88D A 130702

ECP 0437

ECO A05737

INITIAL RELEASE AT REV A RSS

B 130722

ECP 0437

ECO A05742

ADD -202 AND -203 CONFIG RSS

CAGE CODE 0WY55 DWG NO. 2200476 SHEET 2 OF 3

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR-

2.1. SLEEVING: NYLON 6-6 POLYAMIDE MONOFILAMENT

2.1.1. NOMINAL INSIDE DIAMETER: SEE TABLE II

2.1.2. NOMINAL EXPANDED INSIDE DIAMETER: SEE TABLE II

2.1.3. SLEEVING LENGTH: PER TABLE II

2.2. ENVIRONMENTAL:

2.2.1. OPERATING TEMPERATURE: +10º C (+50° F) TO +49º C (+120° F)

2.2.2. NON-OPERATING TEMPERATURE: -35º C (-31°F) TO +60º C (+140° F)

2.3. RELIABILITY:

2.3.1. MTBF: N/A

2.4. PART IDENTIFICATION:

2.4.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR. PART NUMBER

MAY BE APPLIED TO PACKAGING.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

CAGE CODE 0WY55 DWG NO. 2200476 SHEET 3 OF 3

ELECTRIDUCT INC (CAGE CODE: 4J4R6)

FORT LAUDERDALE, FL

NO.

SPC TECHNOLOGY

PART NO.

NOMINAL

DIAMETER

EXPANSION RANGE

SLEEVING

LENGTH EXPANSION

MIN

EXPANSION

MAX

201 BSNY-075-75 .75 .50 1.25 75 FT ± 5 FT

202 BSNY-050-100 .50 .37 .75 100 FT ± 5 FT

203 BSNY-025-200 .25 .12 .38 200 FT ± 5 FT

CAGE CODE 0WY55 DWG NO. 2200542 SHEET 1 OF 3

A 0WY55 2200542 A

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

1313 HALLEY CIRCLE

NORMAN, OKLAHOMA 73069-8480

MILLIMETERS

1 PL

2 PL

ANGLES 2

INCHES

BACKSHELL, TWO-PIECE, STRAIN-RELIEF,

D-SUBMINIATURE

APPROVALS

DWN AWB 160404 RMT JMW 160404

CHK BOB 160404 DOC CSH 160404

ENGR RSS 160404 CM

QA ROC

VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320311 WSR-88D

A 160404

ECP 0540

ECO A06856

CAGE CODE 0WY55 DWG NO. 2200542 SHEET 2 OF 3

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR-

2.1. FUNCTIONAL: STRAIN RELIEF, TWO-PIECE (SPLIT) BACKSHELL FOR D-SUBMINIATURE CONNECTOR

PLUG AND RECEPTACLE. EACH BACKSHELL SHALL COME SUPPLIED WITH VARIOUS SIZED

GROMMETS TO SEAL CABLE RANGES AS SHOWN IN FIGURE 1 (GROMMET TREE MAY VARY FROM

CONFIGURATION SHOWN).

2.2. MATERIAL AND FINISH:

2.2.1. BODY: DIE CAST ZINC, CLEAR FINISH

2.2.2. GROMMETS: PVC

2.2.3. #4-40 JACKSCREW AND SADDLE: STEEL WITH ZINC PLATING AND CLEAR CHROMATE COATING

2.3. OUTLINE: SEE FIGURE 1

2.4. ENVIRONMENTAL:

2.4.1. OPERATING TEMPERATURE: +10º C (+50° F) TO +35º C (+95°F)

2.4.2. NON-OPERATING TEMPERATURE: -35º C (-31°F) TO +60º C (+140° F)

2.5. PART IDENTIFICATION:

2.5.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR. PART NUMBER

MAY BE APPLIED TO PACKAGING.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

CAGE CODE 0WY55 DWG NO. 2200542 SHEET 3 OF 3

NORTHERN TECHNOLOGIES (CAGE CODE 38250)

MARKHAM, ONTARIO, CANADA

NO.

NORTHERN TECHNOLOGIES

PART NO.

SHELL

SIZE

FIGURE

201 C88E000207 A

(15 PIN)

-201 (15 PIN)

SADDLES, SCREWS AND NUTS NOT SHOWN

CAGE CODE 0WY55 DWG NO. 2200543 SHEET 1 OF 4

A 0WY55 2200543 A

SCALE: NONE SHEET 1 OF 4

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

1313 HALLEY CIRCLE

NORMAN, OKLAHOMA 73069-8480

MILLIMETERS

1 PL

2 PL

ANGLES 2

INCHES

BACKSHELL, TWO-PIECE, STRAIN-RELIEF, D-SUB,

RIGHT ANGLE

APPROVALS

DWN AWB 160404 RMT JMW 160404

CHK BOB 160404 DOC CSH 160404

ENGR RSS 160404 CM

QA ROC

VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320310 WSR-88D

A 160404

ECP 0540

ECO A06862

CAGE CODE 0WY55 DWG NO. 2200543 SHEET 2 OF 4

SCALE: NONE SHEET 2 OF 4

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR-

2.1. FUNCTIONAL: STRAIN RELIEF, TWO-PIECE (SPLIT) RIGHT ANGLE BACKSHELL FOR D-SUBMINIATURE

CONNECTOR PLUG AND RECEPTACLE. EACH BACKSHELL SHALL COME SUPPLIED WITH

COMPRESSION INSERT AND TWO #4-40 JACKSCREWS.

2.2.1. BODY: DIE CAST ZINC, NICKEL PLATED

2.2.2. COMPRESSION INSERT: THERMOPLASTIC COMPOUND

2.2.3. #4-40 JACKSCREW: STEEL WITH ZINC PLATING

2.3. OUTLINE: SEE FIGURES 1 AND 2

2.4.1. OPERATING TEMPERATURE: +10º C (+50° F) TO +35º C (+95°F)

2.4.2. NON-OPERATING TEMPERATURE: -35º C (-31°F) TO +60º C (+140° F)

2.5. PART IDENTIFICATION:

2.5.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR. PART NUMBER

MAY BE APPLIED TO PACKAGING.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

CAGE CODE 0WY55 DWG NO. 2200543 SHEET 3 OF 4

SCALE: NONE SHEET 3 OF 4

NORTHERN TECHNOLOGIES (CAGE CODE 38250)

MARKHAM, ONTARIO, CANADA

NO.

NORTHERN TECHNOLOGIES

PART NO.

SHELL

SIZE

FIGURE

201 N30E920000 B

(25 PIN)

202 N30E930000 C

(37 PIN)

-201 (25 PIN)

CAGE CODE 0WY55 DWG NO. 2200543 SHEET 4 OF 4

SCALE: NONE SHEET 4 OF 4

-202 (37 PIN)

CAGE CODE 0WY55 DWG NO. 2200544 SHEET 1 OF 3

A 0WY55 2200544 A

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

1313 HALLEY CIRCLE

NORMAN, OKLAHOMA 73069-8480

MILLIMETERS

1 PL

2 PL

ANGLES 2

INCHES

SHELL, POTTING, D-SUBMINIATURE

APPROVALS

DWN AWB 160404 RMT JMW 160404

CHK BOB 160404 DOC CSH 160404

ENGR RSS 160404 CM

QA ROC

VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

MULTIPLE WSR-88D

A 160404

ECP 0540

ECO A06863

CAGE CODE 0WY55 DWG NO. 2200544 SHEET 2 OF 3

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR-

2.1. FUNCTIONAL: POTTING SHELL FOR D-SUBMINIATURE CONNECTOR BACKSHELLS.

2.2.1. BODY: NYLON

2.3. OUTLINE: SEE FIGURE 1

2.4.1. OPERATING TEMPERATURE: +10º C (+50° F) TO +35º C (+95°F)

2.4.2. NON-OPERATING TEMPERATURE: -35º C (-31°F) TO +60º C (+140° F)

2.5. PART IDENTIFICATION:

2.5.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR. PART NUMBER

MAY BE APPLIED TO PACKAGING.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

CAGE CODE 0WY55 DWG NO. 2200544 SHEET 3 OF 3

ITT CANNON (CAGE CODE 71468)

SANTA ANA, CA

NO.

ITT CANNON

PART NO.

SHELL

SIZE

201 DE50904-1

E

(09 PIN)

202 DA50905-1

A

(15 PIN)

203 DB50906-1

B

(25 PIN)

204 DC50907-1

C

(37 PIN)

CAGE CODE 0WY55 DWG NO. 2200545 SHEET 1 OF 3

A 0WY55 2200545 A

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

3200 MARSHALL AVENUE

NORMAN, OKLAHOMA 73072-8032

MILLIMETERS

1 PL

2 PL

ANGLES 2

INCHES

SLEEVING, EMI SHIELDING, EXPANDABLE,

BRAIDED

APPROVALS

DWN AWB 160405 RMT JMW 160405

CHK BOB 160405 DOC CSH 160405

ENGR RSS 160405 CM

QA ROC

VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320308 2320309

MULTIPLE

WSR-88D

A 160405

ECP 0540

ECO A6864

INITIAL RELEASE AT REV A RSS

CAGE CODE 0WY55 DWG NO. 2200545 SHEET 2 OF 3

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR-

2.1. SLEEVING MATERIAL: ARAMID AND TINNED COPPER

2.1.1. NOMINAL INSIDE DIAMETER: SEE TABLE II

2.1.2. NOMINAL EXPANDED INSIDE DIAMETER: SEE TABLE II

2.1.3. MONOFILAMENT DIAMETER: .010

2.1.4. NOMINAL WALL THICKNESS: .025

2.2. ENVIRONMENTAL:

2.2.1. OPERATING TEMPERATURE: +10º C (+50° F) TO +49º C (+120° F)

2.2.2. NON-OPERATING TEMPERATURE: -35º C (-31°F) TO +60º C (+140° F)

2.3. RELIABILITY:

2.3.1. MTBF: N/A

2.4. PART IDENTIFICATION:

2.4.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR. PART NUMBER

MAY BE APPLIED TO PACKAGING.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

CAGE CODE 0WY55 DWG NO. 2200545 SHEET 3 OF 3

TECHFLEX, INC (CAGE CODE: 02GC6)

SPARTA, NJ

NO.

SPC TECHNOLOGY

PART NO.

NOMINAL

DIAMETER

EXPANSION RANGE

EXPANSION

MIN

EXPANSION

MAX

201 FSN0.38SV .38 .25 .50

202 FSN0.50SV .50 .38 .75

203 FSN0.75SV .75 .50 1.00

204 FSN0.13SV .13 .06 .25

CAGE CODE 0WY55 DWG NO. 2340074 SHEET 1 OF 2

A 0WY55 2340074 C

SCALE: NONE SHEET 1 OF 2

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

1313 HALLEY CIRCLE

NORMAN, OKLAHOMA 73069-8480

MILLIMETERS

1 PL

2 PL

ANGLES 2

INCHES

MARKER SLEEVE KIT, FIBER OPTIC, ST TO ST

APPROVALS

DWN AWB 090521 RMT DMK 130513

CHK DOC MAK 130513

ENGR GSS 130513 CM

QA ROC

SEE SEPARATE PARTS LIST

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320229 WSR-88D

A 130513

ECP 0214

ECO A04297

INITIAL RELEASE AT REV A GSS

B 160111

ECP 0214, 0540

ECO A06714

CHANGE LABELS FOR 3A15W937 AND

3A15W938

RSS

C 160325

ECP 0214, 0540

ECO A06848

CHANGE LABELS FOR 3/103W907 RSS

CAGE CODE 0WY55 DWG NO. 2340074 SHEET 2 OF 2

A 0WY55 2340074 C

SCALE: NONE SHEET 2 OF 2

TABLE A

NO.

APPLICABLE

INFORMATION

CABLE PART

NUMBER

301 SHEETS 1, 2 AND TABLE B 2200370-201

302 SHEETS 1, 2 AND TABLE C 2200370-202

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

2. THIS DRAWING ILLUSTRATES THE MARKER SLEEVES INFORMATION FOR FIBER OPTIC CABLES.

3. ALL LABELS ARE TO BE MARKED USING ITEM 1 ON A BRADY THT PRINTER, MODEL 1024 OR

EQUIVALENT IN 5 POINT ARIAL CHARACTERS.

TABLE B

COLUMN I

“FROM A”

COLUMN II

“FROM B”

COLUMN III

“CENTER”

COLUMN IV

“TO B”

COLUMN V

“TO A”

3A15W937 P1(A14J1)

3A15W937 P3(A14J2)

3A15W937

0WY55ASSY2320229-301

3A15W937 P2(A13S1J4)

3A15W937 P4(A13S2J3)

3A15W938 P1(A14J3)

3A15W938 P3(A14J5)

3A15W938

0WY55ASSY2320229-301

3A15W938 P2(A13S3J2)

3A15W938 P4(A13S3J1)

3A15W944 P1(A14J6)

3A15W944 P3(A14J4)

3A15W944

0WY55ASSY2320229-301

3A15W944 P2(J4-B)

3A15W944 P4(J4-A)

TABLE C

“FROM A”

COLUMN II

“FROM B”

COLUMN III

“CENTER”

COLUMN IV

“TO B”

COLUMN V

“TO A”

3/103W907 P1(A15J4-A)

3/103W907 P3(A15J4-B)

3/103W907

0WY55ASSY2320229-302

3/103W907 P2(A3A1A1U5)

3/103W907 P4(A3A1A1U4)

CAGE CODE 0WY55 DWG NO. 2340097 SHEET 1 OF 2

A 0WY55 2340097 A

SCALE NONE SHEET 1 OF 2

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

1313 HALLEY CIRCLE

NORMAN, OKLAHOMA 73069-8480

MILLIMETERS

1 PL

2 PL

ANGLES

INCHES

MARKER SLEEVE KIT, RF, FORMABLE, COAX

APPROVALS

DWN BOB 121025 RMT DMK 121025

CHK AWB 121025 DOC MAK 121025

ENGR PDK 121025 CM

QA ROC

SEE SEPARATE PARTS LIST

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

2320253 WSR-88D A 121025

ECP 0612

ECO A05448

INITIAL RELEASE AT REV A PDK

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

CAGE CODE 0WY55 DWG NO. 2340097 SHEET 2 OF 2

A 0WY55 2340097 A

SCALE NONE SHEET 2 OF 2

GENERAL

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

2. THIS DRAWING ILLUSTRATES THE MARKER SLEEVE INFORMATION FOR RF, FORMABLE,

COAX CABLES (2200454).

3. ALL LABELS ARE TO BE MARKED USING ITEM 1 ON A BRADY THT PRINTER, MODEL 1244

OR EQUIVALENT IN 5 POINT ARIAL CHARACTERS.

TABLE I

NO.

APPLICABLE

INFORMATION

CABLE

TYPE

CABLE PART NUMBER

301 TABLE II

SMA MALE TO

N MALE RIGHT ANGLE

2200454-201

“TO”

COLUMN II

“CENTER”

COLUMN III

“FROM”

3W104

P1(AT1J2)

3W104

0WY55ASSY2320253-301

3W104

P2(V1 RF DRIVE I/P)