PID Packaging and Marking.docx

*** LTC PID Packaging Consolidated Text *** PLEASE SEE GLOSSARY AT THE END OF THE DOCUMENT FOR FULL TEXT OF THE ITEM DESCRIPTION

AND PACKAGING REFERENCE NUMBERS CALLED OUT FOR EACH NSN.

NSN:013088541

END BELL, ELECTRICAL ROTATING EQUIPMENT

REFERENCE NUMBER:RQ032

REFERENCE NUMBER:RD002

REFERENCE NUMBER:RP001

REFERENCE NUMBER:RA001

REFERENCE NUMBER:RQ002

REFERENCE NUMBER:RQ009

REFERENCE NUMBER:RQ011

REFERENCE NUMBER:RT001

EXCEPTIONS TO ENGINEERING DATA LIST (EDL)

DWG 98749 849232 REV A REPLACED BY REV B.

ENGINEERING CHANGE NOTICES (ECNs):

88A0690-H & 88A0690-R REPLACED BY 88A0690-A1;

96A0085-H REPLACED BY DWG 98749 849232 REV B.

IMPORTANT TECHNICAL DATA CLARIFICATIONS:

- Mechanical contact points (end bell mating flange, bearing race, etc.)do not require coating with primer.

- Dimensions of end bell (end shield) must comply with the tolerances listed on drawing 849233 to be acceptable.

- The varnish (Dolph HI-THERM BC-346-A is acceptable for this application when used in accordance with the instructions on drawing 849234.

- The entire completed exciter core assembly must be heated, dipped, drained and baked in accordance with instructions in NOTE 2 on drawing 849234. Machined surfaces may be masked, but otherwise the entire stator/coil assembly should be bonded together with the cured varnish.

IAW BASIC DRAWING NR 98749 849232

REVISION NR B DTD 04/08/1997

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98749 849233

REVISION NR A DTD 12/19/1996

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98749 849234

REVISION NR DTD 06/15/1988

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98749 849250

REVISION NR DTD 06/15/1988

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98749 849045

REVISION NR DTD 06/15/1988

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98749 849260

REVISION NR DTD 06/15/1988

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98749 849235

REVISION NR DTD 06/15/1988

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 200415485

REVISION NR E DTD 01/30/2020

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98749 88A0690-A1

REVISION NR DTD 10/19/1988

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98749 96A0085-A1

REVISION NR DTD 10/19/1988

PART PIECE NUMBER:

PREP FOR DELIVERY

LINE ITEM 00001 TYPE OF COVERAGE: DLA DIRECT, CONUS

PKGING DATA-QUP:001

WILL BE PACKAGED IN ACCORDANCE WITH ASTM D3951.

GLOSSARY

PACKAGING TEXT

THE FOLLOWING PARAGRAPH APPLIES TO ALL PACKAGING CALLED OUT IN THIS DOCUMENT:

All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951.

Mark and label all packaging and packing in accordance with MIL-STD-129.

The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order.

ITEM DESCRIPTION TEXT

REFERENCE NUMBER RQ032

RQ032: EXPORT CONTROL OF TECHNICAL DATA

This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.

The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at:

https://www.dla.mil/HQ/LogisticsOperations/EnhancedValidation/

To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data.

REFERENCE NUMBER RD002

RD002, COVERED DEFENSE INFORMATION APPLIES

REFERENCE NUMBER RP001

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

REFERENCE NUMBER RA001

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB

AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

REFERENCE NUMBER RQ002

RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL

REQUEST FOR VARIANCE (DEVIATION OR WAIVER)

REFERENCE NUMBER RQ009

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

REFERENCE NUMBER RQ011

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

REFERENCE NUMBER RT001

RT001: MEASURING AND TEST EQUIPMENT