Statement_of_Work.doc

STATEMENT OF WORK

FOR THE

AIRCRAFT LAUNCHER INTERFACE COMPUTER (ALIC)

CHASSIS AND MECHANICAL ASSEMBLIES

30 March 2017

1. SCOPE

Naval Air Warfare Center Weapons Division (NAWCWD) Point Mugu Code 486M00E intends to procure the Aircraft Launcher Interface Computer (ALIC) Chassis and the mechanical assemblies. The ALIC Chassis houses all of the Electronic Assemblies, Power Supply and the Wiring Harness. The ALIC is an avionics assembly which provides a functional interface between the F-16C/D Block 40/50/52 aircraft and the AGM-88 HARM Missile. The ALIC is attached to the aft end of the LAU-118(V) 4/A launcher. The ALIC provides the necessary power and control interface for the AGM-88B/C/F Missile. NAWCWD Code 486M00E has a requirement to fabricate ALIC’s for the customer. Listed in paragraph 2.1 are the applicable drawings for the ALIC Chassis and the mechanical assemblies.

2. APPLICABLE DOCUMENTS

2.1 Drawings

ALIC Chassis and the Mechanical Subassemblies consist of the following drawings (available on CD):

2959150-4 Rev. M Aircraft Launcher Interface Computer 2959140-4 Rev. AD Aircraft Launcher Interface Computer (ALIC) Assembly

2959055-1 Rev. N Chassis, Aircraft Launcher Interface Computer (Machined) 2959054-1 Rev. M Chassis, Aircraft Launcher Interface Computer (Casting)

2959111-1 Rev. F Gasket, Strip

2959118-1 Rev. G Cover Assembly, Pylon 2959119-1 Rev. J Cover, Pylon

2959113-1 Rev. K Cover Assembly, Motherboard (A9)

2959114-1 Rev. H Cover, Motherboard

2959115-1 Rev. E Bracket, Motherboard, Cover

2959120-1 Rev. L Cover Assembly, Relay 2959121-1 Rev. K Cover, Relay

2959109-1 Rev. F Cover Assembly, Daughterboard 2959110-1 Rev. G Cover, Daughterboard 2993004-1 Rev. G Adapter, Ejector, AFT 2993003-1 Rev. G Adapter, Ejector, FWD

2959107-1 Rev. C Nutplate, Time Meter

2993012-1 Rev. G Insert, Forward Bulkhead

2959034-1 Rev. D Pin, Guide 2981790-1 Rev. D Gasket, ETM

2959148-1 Rev. B Plate, Warranty

2959149-1 Rev. D Plate, Identification

2959131-1 Rev. B Nut Plate, Relay Bracket 2959064-1 Rev. E Bracket, Relay, Side

2959130-1 Rev. E Bracket, Relay, Top

2964482-1 Rev. H Spring, Flat 2964524-1 Rev. F Card Retainer, Wedge Lock

2964483-1 Rev. H Ejector

2964481-1 Rev. G Stiffener, Vertical

2964480-1 Rev. F Stiffener, Horizontal

2981788 Rev. C

Gasket, Bulkhead Connector 2981791 Rev. C

Gasket, Pylon Connector 3038392 Rev. C

Primer, Silicon Rubber

3042154-1 Rev. U Circuit Card Assembly, Relay (A7)

2261693-1 Rev. -

Pad, Rubber

3100828-1 Rev. R Circuit Card Assembly, 286 CPU (A5) (PROD) 3100848-1 Rev. B Heat Sink 3116054-1 Rev. B Insulator, Thermally Conductive

2959070-1 Rev. W Circuit Card Assembly, System I/O (A3)

2959075-1 Rev. N Circuit Card Assembly, Memory (A4)

2959080-1 Rev. AJ Circuit Card Assembly, Video (A1)

2959039-1 Rev. E Label, Temperature Indicating

3. REQUIREMENTS

The Contractor shall manufacture, package and deliver twelve (12) sets of ALIC Chassis and the mechanical assemblies so that twelve (12) complete ALIC units (p/n 2959150-4) can be assembled together. For each of the drawings listed in the Table I – Procurement Part List, the contractor shall deliver all parts that are called out on the drawings unless they are noted as exception in Table I. The quantity for each of these parts shall be adequate to make twelve (12) complete ALIC units (p/n 2959150-4). All parts shall be done in accordance with the drawings listed in paragraph 2.1 and also with the requirements listed below:

3.1 Items must meet all drawing dimensions, tolerances, specifications requirements and performance requirements. The Government shall perform the First Article Acceptance Test (FAAT) on the first set of ALIC Chassis and the mechanical assemblies delivered by the Contractor. The Contractor shall not continue with the next set fabrication until the Government grants the FAAT approval. Form, fit and function shall be conducted during FAAT to ensure total compliance with the drawing and SOW requirements.

The contractor’s risk mitigation plan shall be addressed in the proposal and shall be enforced by the contractor upon early detection of risk occurring and shall be mitigated by the contractor to avoid negative impact on delivery schedules. On time delivery of the ALIC Chassis and the mechanical assemblies is a requirement. Late delivery shall not be accepted.

Quality assurance processes and methods on completed ALIC Chassis and the mechanical assemblies are the sole and full responsibilities of the contractor. The contractor’s Quality Management System must be certified to be in conformance to AS9100C and ISO 9001:2008 as a minimum. Contractor must provide copy of the Certifications in order to propose and be considered under this solicitation.

Periodic Task Review Meetings to review status of deliverables, progress, quality assurance checks and inspect shall be conducted by NAWCWD Point Mugu representatives at the Contractor’s Facility on a mutually agreed upon meeting schedule.

3.2 Task 1: First Article Unit for ALIC Chassis and the mechanical assemblies The Contractor shall manufacture and deliver one (1) set of ALIC Chassis and the mechanical assemblies IAW paragraph 2 four months after award of contract. The Government shall perform form, fit and function check at a Government facility to ensure ALIC Chassis and the mechanical assemblies were built correctly and met all drawing requirements. Contractor participation is not required. Discrepancies shall be documented and provided to the Contractor for corrective actions.

3.3 Task 2: Deliverable Units for ALIC Chassis and the mechanical assemblies Upon successful completion of FAAT, the Government shall notify the Contractor to proceed with the manufacture and delivery of the remaining sets. The remaining sets shall be delivered 120 days following the initial acceptance of the First Article Unit. The acceptance inspection of these sets shall be done at NAWCWD Point Mugu. Contractor participation is not required. Discrepancies shall be documented and provided to the Contractor for corrective actions.

3.4 The contractor is responsible to install the following parts onto the Government supplied Circuit Card Assemblies that are needed to make 12 sets of ALIC units (p/n 2959150-4) except for the Mux Bus (A2) part number 3042172-1 Circuit Card Assemblies:

a. 2964482-1 Spring, Flat

b. 2964524-1 Card Retainer, Wedge Lock

c. 2964483-1 Ejector

d. 2964481-1 Stiffener, Vertical

e. 2964480-1 Stiffener, Horizontal

3.5 The contractor shall ensure adequate consideration of packaging, handling, storage, and transportation (PHS&T) requirements for the ALIC Chassis and its mechanical assemblies in accordance with industry standards.

4. DATA REQUIREMENTS

The Contractor shall provide a Quality Assurance Certification with the delivery of each set of the ALIC

Chassis and the mechanical assemblies to certify that quality control and inspection have been performed to ensure the proper materials were used and the parts made are in full compliance with the drawing requirements. CDRL A00A

5. ***GOVERNMENT TECHNICAL REPRESENTATIVE

Commander, NAWCWD

Code XXXXXXX, Bldg. XXX

Point Mugu, CA. 93042

Attn: XXXXX

Tel #: XXX-XXX-XXXX

Fax #: XXX-XXX-XXXX

Email Address: XXXXX

6. DELIVERY INSTRUCTION

***The First Article Unit shall be shipped to the following address for First Article Acceptance Test to be performed by the Government:

Commander, NAWCWD

Code XXXXX, Bldg. XXX

Point Mugu, CA. 93042

Attn: XXXXX

*** To be completed at contract award.

Drawing Number

Table I - Procurement Part List

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item) Form Approved

OMB No. 0704-0188

Public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA. 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project (0704-0188), Washington, DC 20503. Please DO NOT RETURN your form to either of these addresses. Send completed form to the Government Issuing Contracting Officer for Contract/PR No. listed in Block E.

ALIC Chassis and mechanical assemblies

N/A

DISTRIBUTION

b. COPIES

SUBMISSION

N/A

Block 4: Contractor format is acceptable as long as DID is used for guidance.

Block 9: Use Distribution Statement E: Distribution Statement E.

Distribution authorized to DoD components only, Administrative or Operational Use, 1 September 2016, Other requests for this document shall be referred to NAWCWD Point Mugu, Code 486M00E.

Blocks 10, 12 & 13: Shall be delivered concurrent with hardware.

Block 14: Submit in an electronic format agreed upon by both Government and Contractor prior to 1st submittal.

See Contract Clause 5252.247-9505, Technical Data and Information for distribution addresses.

15. TOTAL

Naval Air Warfare Center Weapons Division

China Lake, CA 93555-6100