The file's text, extracted by GovTribe without its formatting.
Requirements List
NSN
PART NUMBER
NOMENCLATURE
Description
Qty
4920-01-020-8475
SE27-0001
CONTROL WHEEL STRAIGHT EDGE
Used to align both control wheels to a common plane, and to hold them in a neutral position.
2
5120-01-582-2336
ST848
O-RING INSTALLATION TOOL
Protect o-ring seals and backup washers during installation over threaded fittings.
2
4920-01-610-4818
ST9501B
PIN, ALIGNMENT, BOLT INSTALLATION
Used to protect threads on fastners of the Airstairs when installing the Airstair Rails.
2
5120-01-472-6224
A10002-7
Pitot Static Cover Inst/Rem Tool
Used to install pitot static cover.
3
5930-01-581-8715
A27092-106
SWITCH,PROXIMITY
Used to actuate/deactuate proximity sensors (cylindrical, rectangular, and reed) during test procedures.
4
4920-01-543-7570
A71015-108
LIFT FIXTURE - ENGINE ACCESSORY
325 lb limit lifting device used with multiple adapters to remove and install various LRUs.
4
4920-01-471-0203
B78009-26
LOCK EQUIPMENT,T/R
Used to electrically interrupt the thrust reverser deployment system at the reverser control valve module.
2
1730-01-469-6211
C07002-1
WING JACK ADAPTER
Used to adapt wing jacking point to standard tripod jack with 3/4" radius cup.
3
1730-01-468-8880
C07005-1
FITTING,ASSY AIRCRAFT TIEDOWN
Used for tiedown of airplane to pull down the airplane tail during recovery operations.
1
4920-01-580-6927
C22005-25
ADAPTER ASSEMBLY,CABLE BREAKOUT
Used at the O-level for an item of SE which can be used to access breakout contacts of PI connector on the front panel of the FCC.
2
1730-01-604-7415
C27001-42
SET,LOCK OUTBOARD GROUND SPOILE
Used to lock the outboard ground spoilers (number 1 and 12) in the fully extended position. Contains Two Lock Assemblies.
6
4920-01-469-6247
C27022-1
SET,CLAMP TRAILING EDGE FLAP TORQ
Used to prevent the trailing edge flap drive system from rotating when the torque tubes are disconnected or removed for maintenance.
4
1730-01-580-9111
C27038-6
PIN,LOCKOUT DEPRESSURIZATION VALVE
Used to lockout the leading edge depressurization valve so the leading edge slats & flaps do not move during maintenance operations. Allows the trailing edge flaps to operate without the leading edge slats operating.
8
1730-01-587-0549
C27047-41
SET,LOCK FLIGHT SPOILER ACTUATOR
Used to hold the flight spoilers (numbers 2 thru 5 and 8 thru 11) in the fully deployed position during ground maintenance operations. Contains 8 Lock Assemblies. Not applicable to SFP Airplanes; See C27047-43 for SFP Airplanes.
4
5120-01-580-9431
C32012-12
SET,TOOL MLG+NLG WHEEL RET NUT
Used to install or remove the MLG or NLG retention nut
8
5365-01-581-2083
C32022-17
SET,THREAD PROTECTOR MLG
To protect the threads on the MLG axles during wheel/brake replacement or maintenance requiring removal of the wheels or brake assy.
8
1730-01-581-6170
C32022-20
SET,THREAD PROTECTOR NLG
Used to protect nose landing gear threads during wheel installation and removal.
8
5120-01-581-7198
C32035-1
PIN, INSERTER AND REMOVER
Used for removal and installation of the nose landing gear metering pin.
1
4920-01-620-4677
C36001-64
TEST EQUIPMENT - ENGINE BLEED AIR SYSTEMS
Used to perform operational or functional test of engine bleed air system components.
4
4920-01-492-4560
C78019-15
HOLD OPEN EQUIPMENT,T/R COWL
Used to hold open the thrust reverser cowl during engine removal or installation.
4
1730-01-471-6723
C78021-1
HOLD OPEN EQUIPMENT, 65 DEG T/R CO
Used to open and hold thrust reverser cowl at 65 degrees for precooler instl/removal with engine in place. to use this equipment. C78019 hold open equipment is used with outboard arm replaced.
2
5120-00-165-2401
F70038
WRENCH ASSY - DOOR HANDL MECHAN
Used to install or remove the Door Handle Mechanism Nut in the Entry and Galley Doors.
2
5120-00-571-3572
F71267
WRENCH ASSY, PINION GEAR
Used to prevent rotation of the pinion gear of the stabilizer trim actuator, while testing manual operation of the stabilizer trim system.
2
4920-00-586-6044
F72790
PROTRACTOR MOUNT USED WITH MULTIPURPOSE PROTRACTOR
Used in conjunction with a protractor to measure rotational movement of the pilots and copilots control wheel during aileron & spoiler control system adjustment or test.
2
4820-01-471-0194
F72928-58
REGULATOR,AIR PRESSURE ELEV FEEL
Used to supply regulated air and to monitor pressure at the elevator feel computer during elevator system functional test.
4
4930-01-468-8745
F72942-1
DOOR LUBE SET
Used to reach inaccessible flush lubrication fittings on entry, cargo, service, and galley door camshaft bearings.
1
1730-00-422-4139
F80049-46
LOCK,GROUND TE FLAP BYPASS VALVE
Used to prevent electrical connection at flap bypass shutoff valve.
4
5120-01-469-1758
F80055-1
ASSEMBLY,TRAMMEL BAR STAB TRIM A
Used to measure rigging positions in the stabilizer trim actuator during functional testing.
2
4920-01-469-8478
F80166-1
FIXTURE,TEST FUEL SURGE PRESSURE
Used to provide a means of applying pneumatic pressure or a vacuum to test positive and negative relief action of the relief valve while installed on the fuel surge tank.
2
1740-01-618-3362
J20002-59
LOAD POSITIONER
Used to provide horizontal and vertical movement during LRU removal/installation.
4
File details come from the government source that posted it.
Updated .