N6449822Q4203.docx

N6449822Q4203

Section B - Supplies or Services and Prices

CONTROLLER,MOTOR

FFP

DRS Drip Proof Motor Controllers 440 VOLTS 3 PH 60 HZ

SIZE 3, I/A/W MIL-DTL-2212 P/N 699ED1690A

FOB: Destination

NSN: 6110013237615

VENDOR PART NR: 100001814575-0040

PURCHASE REQUEST NUMBER: 1300997499

PSC CD: 6110

NET AMT

Section C - Descriptions and Specifications

STATEMENT OF WORK

Statement of Work (SOW)

Motor Controllers

1.0 INTRODUCTION

1.0.1 The Naval Surface Warfare Center Philadelphia Division (NSWCPD) is a Department of Defense entity responsible for research and development, test and evaluation, engineering and fleet support organization for the Navy’s ships, submarines, military watercraft and unmanned vehicles. This requirement is for NSWCPD Code 433, which is responsible for Launch Recovery and Handling.

1.0.2 This contract is for non-personal services. It does not create employment rights with the U.S. Government whether actual, inherent, or implied

1.0.3 Government/Contractor Relationship

1.0.3.1 The services to be delivered under this Contract are non-personal services and the parties recognize and agree that no employer-employee relationship exists or will exist under the Contract between the Government and the Contractor's personnel. Therefore, it is in the best interest of the Government to provide both parties a full understanding of their respective obligations.

1.0.3.2 The Contractor employees shall identify themselves as Contractor personnel by introducing themselves or being introduced as Contractor personnel and displaying distinguishable badges or other visible identification for meetings with Government personnel. In addition, Contractor personnel shall appropriately identify themselves as Contractor employees in telephone conversations and in formal and informal written correspondence.

1.0.3.3 Contractor personnel under this Contract shall not engage in any of the inherently Governmental functions listed at FAR Subpart 7.5 or DFARS Subpart 207.5.

1.0.4 Employee Relationship:

1.0.4.1 The services to be performed under this Contract do not require the Contractor or its personnel to exercise personal judgment and discretion on behalf of the Government. Rather the Contractor's personnel will act and exercise personal judgment and discretion on behalf of the Contractor.

1.0.4.2 Rules, regulations, directives, and requirements that are issued by the U. S. Navy and NSWCPD under its responsibility for good order, administration, and security are applicable to all personnel who enter a Government installation or who travel on Government transportation. This is not to be construed or interpreted to establish any degree of Government control that is inconsistent with a non-personal services contract.

1.0.4.3 Inapplicability of Employee Benefits: This Contract does not create an employer-employee relationship. Accordingly, entitlements and benefits applicable to such relationships do not apply.

1.0.4.4 It is the Contractor's, as well as the Government's, responsibility to monitor Contract activities and notify the Contracting Officer if the Contractor believes that the intent of this Section has been or may be violated.

1.0.4.4.1 The Contractor shall notify the Contracting Officer in writing via letter or email within three (3) calendar days from the date of any incident that the Contractor considers to constitute a violation of this Section. The notice should include the date, nature, and circumstances of the conduct; the name, function, and activity of each Government employee or Contractor official or employee involved or knowledgeable about such conduct; identify any documents or substance of any oral communication involved in the conduct; and the Contractor's estimated date when, absent a response, cost, schedule or performance will be impacted.

1.0.4.4.2 The Contracting Officer will, within five (5) calendar days after receipt of notice, respond to the notice in writing. In responding, the Contracting Officer will either:

1.1 BACKGROUND

The Motor Controller for Navy Standard Slewing Arm Davits have a long lead time and have caused delays to delivery of SLADs. The three motor controllers will be used for new SLAD production units to prevent delivery delays.

1.2 SCOPE OF WORK

The Contractor shall fabricate, machine, provide inspection compliance documentation, and deliver the following:

DRS Motor Controller, PN 6999ED1690A

The Contractor shall deliver all units together.

2.0 APPLICABLE DOCUMENTS

2.1 NAVSEA Drawing Number 583-6743669 Rev H – Davit, Boat, Slewing General Assembly

The Contractor shall reference and utilize the latest version available when performing tasks within this SOW. These documents will be provided by the Government.

3.0. REQUIREMENTS

3.1 Production Units

3.1.1 The contractor provide 3 motor controllers, DRS Drip proof Motor Controllers Part number 6999ED1690A, 440 Volts, 3 Phase, 60 Hz, Size 3, IAW MIL-DTL-2212.

3.2 Motor Controllers Delivery.

3.2.1 The Contractor shall deliver all Motor Controllers to the following location:

Naval Surface Warfare Center- Philadelphia Division Building 542 542 Langley Avenue, Philadelphia, PA 19112 Attn: James Devine, Code 433

(267) 547-8580

3.2.2 Technical Point of Contact

3.3 Delivery Date

The contractor shall deliver the Motor Controllers no later than 400 days ARO.

3.3 Manufacturing Phase-Out or Discontinuation of Production, Diminishing Sources, and Obsolete Materials or Components

3.3.1 The contractor shall notify the contracting officer immediately upon determining the unavailability of obsolete materials or components. The contractor may recommend a solution to include the impact on the contract price and delivery. The contractor shall not initiate any item redesign or incur any additional costs without the express, written authorization of the contracting officer.

4.0 DATA REQUIREMENTS

N/A

5.0 SECURITY REQUIREMENTS

5.1 SECURITY TRAINING. Not Used

5.2 ON SITE WORK. Not Used

5.4 OPERATIONS SECURITY (OPSEC)

5.4.1 The Contractor shall protect critical information associated with this contract to prevent unauthorized disclosure. The NSWC Philadelphia Division's (NSWCPD) Critical Information List (CIL)/ CIIL (Critical Indicators and information list) will be provided on site, if warranted. Performance under this contract requires the contractor to adhere to OPSEC requirements. The Contractor may not impose OPSEC requirements on its subcontractors unless NSWCPD approves the OPSEC requirements. During the period of this contract, the Contractor may be exposed to, use, or produce, NSWCPD Critical Information (CI) and/or observables and indicators which may lead to discovery of CI. NSWCPD’s CI will not be distributed to unauthorized third parties, including foreign governments, or companies under Foreign Ownership, Control, or Influence (FOCI) unless such FOCI has been appropriately mitigated through measures approved by the Defense Counterintelligence and Security Agency. Questions concerning these requirements shall be directed to the PCO.

5.4.2 CUI correspondence transmitted internally on the contractor's unclassified networks or information systems, and externally, shall be protected per NIST SP-800-171, Protecting Controlled Unclassified Information (CUI) in Non-federal Systems and Organizations.

Assembled large components/systems being transported to and from testing areas, other production or government facilities (whether or not on public roadways) shall be in an enclosed van trailer or covered flatbed trailer. Component/System outside storage, staging, and test areas shall be shielded/obscured from public view wherever physically possible.

5.4.3 NSWCPD’s CI shall not be publicized in corporate wide newsletters, trade magazines, displays, intranet pages or public facing websites. Media requests related to this project shall be directed to the PCO, and the COR who will forward the required to the NSWCPD Public Release Authority for review.

5.4.4 Any attempt by unauthorized third parties to solicit, obtain, photograph, or record, or; incidents of loss/compromise of government Classified or CI, Business Sensitive, Company Proprietary information related to this or other program must be immediately reported to the contractor's Facility Security Officer and Cognizant Security Office and/or the Naval Criminal Investigative Service, and the NSWC PD Security Division (Code 105).

5.5 RECEIPT, STORAGE, AND GENERATION OF CONTROLLED UNCLASSIFIED INFORMATION (CUI) All Controlled Unclassified Information (CUI) associated with this contract must follow the minimum marking requirements of DoDI 5200.48, Section 3, paragraph 3.4.a, and include the acronym "CUI" in the banner and footer of the document. In accordance with DoDI 5200.48, CUI must be safeguarded to prevent Unauthorized Disclosure (UD). CUI export controlled technical information or other scientific, technical, and engineering information must be marked with an export control warning as directed in DoDI 5230.24, DoDD 5230.25, and Part 250 of Title 32, CFR. Nonfederal information systems storing and processing CUI shall be protected per NIST SP-800-171, or subsequent revisions. All transmissions to personal email accounts (AOL, Yahoo, Hotmail, Comcast, etc.) and posting on social media websites (Facebook, Instagram, Twitter, LinkedIn, etc.) are prohibited. Destroy CUI associated with this contract by any of the following approved methods: A cross-cut shredder; a certified commercial destruction vendor; a central destruction facility; incineration; chemical decomposition; pulverizing, disintegration; or methods approved for classified destruction.

5.6 PLANNING, PROGRAMMING, BUDGETING AND EXECUTION (PPBE) DATA.

5.7 U-NNPI SECURITY REQUIREMENTS N/A

5.8 U-NNPI

6.0 PLACE OF PERFORMANCE

100% of the contract effort will take place the contractor’s facility.

7.0 TRAVEL

7.1 The contractor will not need travel for this work.

9.0 GOVERNMENT FURNISHED INFORMATION

10.0 PURCHASES

Not Used

11.0 COUNTERFEIT MATERIAL PREVENTION

11.1 Electronic End-Items

11.1.1 Counterfeit Parts and Materials Planning

The contractor planning shall document procedures and processes to minimize the risk of procuring and/or using counterfeit parts and materials, and their process for detecting counterfeit materiel in the event it is procured. This requirement applies to both new/modified and existing mission and safety critical hardware. SAE AS5553 contains information regarding the detection, avoidance, and mitigation of counterfeit electronic components, and may be used as a reference document for the development of the plan.

11.1.2 Counterfeit Parts and Materials System

System criteria. A counterfeit electronic part detection and avoidance system shall include risk-based policies and procedures that address, at a minimum, the following areas:

11.1.3 Preventing Counterfeit Parts and Materials

The Contractor shall take steps as defined in DFARS 252.246-7007 and herein to minimize the risk of receiving counterfeit parts and materials. The Contractor shall:

• Maximize availability of authentic, originally designed and/or qualified parts throughout the product’s life cycle, including management of parts obsolescence

• Assess potential suppliers to minimize the risk of receiving counterfeit parts or materials

• Maintain a listing of approved suppliers with documented criteria for approval and removal of suppliers from the list

• Have purchasing procedures which require the selection of parts and materials from OM or authorized suppliers whenever possible

• Require a certificate of compliance and supply chain traceability for all electronic part purchases, and provide to the Government upon request

• Use Government or industry services such as GIDEP and other commercially available services to identify part or supplier quality or authenticity problems

• Define minimum inspection and test requirements for parts being procured from unauthorized suppliers, and shall ensure that in-house, third-party, and/or distributor inspection and test procedures and facilities comply with these requirements

• Incorporate procurement clauses which plainly identify quality requirements and liability to all approved suppliers

• Flow the requirements above to affected Subcontractors

SAE AS6174 contains information regarding the detection, avoidance, and mitigation of counterfeit materiel, and may be used as a reference document for meeting the above steps.

11.1.4 Warranty “Counterfeit”

11.1.4.1 Seller warrants the goods delivered pursuant to this Contract, unless specifically stated otherwise in this Contract, shall (i) be new (ii) be free from defects in workmanship, materials, and design and (iii) be in accordance with all the requirements of this Contract. Seller further warrants that the performance of work and services shall conform with the requirements of this Contract and to high professional standards. All warranties in this Contract shall survive inspection, test, final acceptance and payment of goods and services.

11.1.5.1 Unless Buyer expressly identifies the goods that are procured under this Contract as nontechnical and for Buyer’s internal use only, Seller warrants without limitation as to time that the goods delivered pursuant to this Contract shall (i) be and only contain materials obtained directly from the OM or an authorized OM reseller or distributor (collectively, an Authorized Distributor); (ii) not be or contain Counterfeit Items or Suspect Counterfeit Items, as defined below; and (iii) contain only authentic, unaltered OM labels and other markings. Seller shall obtain and retain all documentation required to fully trace the distribution and sale of the goods delivered hereunder back to the relevant OM, and, on request of Buyer, shall provide such authenticating documentation. Counterfeit Item means an unlawful or unauthorized reproduction, substitution, alteration, or the false identification of grade, serial number, lot number, date code, or performance characteristic, that has been knowingly mismarked, misidentified, or otherwise misrepresented to be an authentic, unmodified item from the OM, an Authorized Distributor, or an Aftermarket Manufacturer as defined in SAE AS5553 “Counterfeit Electronic Parts;

Avoidance, Detection, Mitigation, and Disposition” (Authorized Aftermarket Manufacturer). A Suspect Counterfeit Item means an item for which credible evidence (including, but not limited to, visual inspection or testing) provides reasonable doubt that the item is authentic. Seller warrants that it will not act as or engage an independent distributor, non-authorized distributor, non-franchised distributor, non-authorized supplier, or non-authorized reseller (collectively, Broker), to assist it in delivering goods pursuant to this Contract unless the Buyer provides prior written approval to do so. Any Seller request to procure from a Broker shall include complete and compelling support for such request and shall include all actions completed by Seller to ensure the goods thus procured are not Counterfeit Items. Seller’s supporting documentation shall include: (i) results of authentication test and analysis conducted (reference SAE AS5553 ), (ii) traceability with identification of all supply chain intermediaries wherever such traceability exists, and (iii) identification of and traceability to the source for any remarked or resurfaced material. Seller shall include the substance of this Section in any agreement between Seller and Seller’s lower tier subcontractors, including in any agreement between Seller and Seller’s Broker, and Seller shall cause Seller’s lower tier subcontractors and Seller’s Broker to include the substance of this Section in all agreements with any of their lower tier subcontractors.

11.1.5.2 Unless Buyer expressly identifies the goods that are procured under this Contract as nontechnical and for Buyer’s internal use only, Seller, as OM, Authorized Distributor, Authorized Aftermarket Manufacturer or Broker approved by Buyer, further warrants that it has and shall maintain a Counterfeit Item risk mitigation process, internally and with its suppliers, (reference SAE AS5553), for goods delivered hereunder, and in accordance with the standards or instructions set forth in any Buyer’s specifications and other required provisions and specifications incorporated into this Contract. Buyer shall have the right to audit, inspect, and / or approve the processes at any time before or after delivery of the goods ordered hereunder. Seller shall provide evidence of the Seller’s risk mitigation process to Buyer upon request. Buyer shall have the right to require changes to the processes to conform with Buyer’s defined standards, if any. Seller and Seller's lower-tier subcontractors that are allowed access to the US Government Industry Data Exchange Program (GIDEP) shall participate in monitoring GIDEP reports and Seller shall act on GIDEP reports that affect product delivered to Buyer. Seller shall immediately notify Buyer with the pertinent facts if Seller becomes aware of or suspects that items delivered for the Contract are, or contain, suspect or confirmed counterfeit items. Failure of the Seller or any of its lower-tier subcontractors to conform its processes with Buyer’s defined standards may result in the termination of this Contract in accordance with the termination provisions set forth herein. If, during Buyer’s inspection procedures, a good delivered hereunder is discovered to be a Counterfeit Item or Suspect Counterfeit Item, Buyer shall have the right to quarantine the good for further investigation of its authenticity. Buyer’s investigation may include the participation of third parties or governmental investigative agencies as required by law or regulations by Buyer’s customer, or by Buyer, in its sole discretion. The Seller and/or the Seller’s lower-tier subcontractors shall cooperate in good faith with any investigation conducted by Buyer, including, but not limited to, cooperation by Seller’s or Seller’s lower-tier subcontractor’s staffs responsible for the maintenance and disclosure of all design, development, manufacturing, and traceability records with respect to the good in possession of Seller or Seller’s lower-tier subcontractor. Upon Buyer’s request, Seller shall provide Buyer certificates of conformance with respect to the goods delivered. Buyer shall not be required to return the good to the Seller during the investigation process or thereafter. Buyer shall not be liable for payment to Seller of the price of any Suspect Counterfeit Items under investigation. When so authorized by Buyer, Seller shall be responsible for counterfeit risk mitigation testing and providing traceability identifiers (i.e. Date Code / Lot Code, Serial number) for Broker procured parts, and identifying items delivered to Buyer that contain such parts. If Buyer determines in its sole discretion that there is credible evidence after visual inspection, testing, or other information that a good delivered under this Contract may have been misrepresented by the Seller or Seller’s lower-tier subcontractor and constitutes a Counterfeit Item or Suspect Counterfeit Item, Seller, or its lower-tier subcontractor, shall, if directed by Buyer to do so, issue a GIDEP alert and shall ensure suspect or confirmed Counterfeit Items are not delivered to Buyer. Buyer reserves its right hereunder, to issue its own GIDEP alert if, after investigation, Buyer concludes, in its sole estimation, that a good is a Counterfeit Item or Suspect Counterfeit Item. Seller shall include the substance of this Section in any agreement between Seller and Seller’s lower tier subcontractors, including in any agreement between Seller and Seller’s Broker, and Seller shall cause Seller’s lower tier subcontractors and Seller’s Broker to include the substance of this Section in all agreements with any of their lower tier subcontractors.

11.1.5.3 Seller warrants without limitation as to time that any hardware, software and firmware goods delivered under this Contract: (i) shall not contain any viruses, malicious code, Trojan horse, worm, time bomb, self-help code, back door, or other software code or routine designed to: (a) damage, destroy or alter any software or hardware; (b) reveal, damage, destroy, or alter any data.

11.1.6 Counterfeit Mitigation

Seller warrants that the goods delivered pursuant to this Contract shall (i) be and only contain materiels obtained directly from the OM or an authorized OM reseller or distributor; (ii) not be or contain Counterfeit Items, as defined below; and (iii) contain only authentic, unaltered OM labels and other markings. Seller shall obtain and retain all documentation required to fully trace the distribution and sale of the goods delivered hereunder back to the relevant OM, and, on request of Buyer, shall provide such authenticating documentation. Counterfeit Items include, but are not limited to, goods or separately-identifiable items or components of goods that: (i) are an illegal or unauthorized copy or substitute of an OM item; (ii) are not traceable to an OM sufficient to ensure authenticity in OM design and manufacture; (iii) do not contain proper external or internal materials or components required by the OM or are not constructed in accordance with OM design; (iv) have been re-worked, re-marked, re-labeled, repaired, refurbished, or otherwise modified from OM design but not disclosed as such or are represented as OM authentic or new; (v) have not passed successfully all OM required testing, verification, screening, and quality control processes; or (vi) an item with altered or disguised documentation, package labeling, or item marking intended to mislead a person into believing a non-OM item is genuine, or that an item is of better or different performance when it is not. Seller further warrants that it has and shall have an internal Counterfeit Item control process for goods delivered hereunder in accordance with the standards or instructions set forth in any Buyer's specifications, including but not limited to specifications, or other provisions incorporated into this Contract. Buyer shall have the right to audit, inspect, and / or approve the processes at any time before or after delivery of the goods ordered hereunder. Buyer shall have the right to require changes to the processes to conform to Buyer's defined standards, if any. Failure of the Seller to conform its processes to Buyer's defined standards may result in the termination of this Contract in accordance with the termination provisions set forth herein. Seller shall include this clause in any agreement between Seller and its lower tier sellers.

11.1.7 Seller warrants that any hardware, software and firmware goods delivered under this Contract: (i) shall not contain any viruses, malicious code, Trojan horse, worm, time bomb, selfhelp code, back door, or other software code or routine designed to: (a) damage, destroy or alter any software or hardware; (b) reveal, damage, destroy, or alter any data; (c) disable any computer program automatically; or (d) permit unauthorized access to any software or hardware; (ii) shall not contain any third party software (including software that may be considered free software or open source software) that (a) may require any software to be published, accessed or otherwise made available without the consent of Buyer, or (b) may require distribution, copying or modification of any software free of charge; and (iii) shall not infringe any patent, copyright, trademark, or other proprietary right of any third party or misappropriate any trade secret of any third party.

11.1.8 New Materiels; Anti-Counterfeit Mitigation

11.1.8.1 For Subcontractors, Contract Manufacturers, and Authorized Distributors - Only new and authentic materiel are to be used in products delivered to Buyer. No counterfeit or suspect counterfeit materiel is to be contained within the delivered product. Materiel shall be purchased directly from the OMs, or through the OMs Authorized Distributor. Documentation must be available that authenticates traceability to the applicable OM. Independent Distributors (Brokers) shall not be used without written consent from Buyer.

11.1.8.2 For Independent Distributors - Independent Distributor's procedures shall meet the intent of the requirements of IDEA-STD-1010 & SAE AS6081 and have a Quality Management System certified to AS9100 and/or AS9120. When available, the OM’s Certificate of Conformance and all traceability documentation shall be included with each shipment of parts. It shall include the manufacturer's name, part number, date codes, lot codes, serializations, and / or any other batch identifications. Inspections and tests required are as noted in the Subcontract. Recorded evidence of all testing performed shall be included with each shipment. If suspect/counterfeit parts are furnished under this Subcontract and are found in any of the Goods delivered hereunder, such items will be impounded by Buyer. The Seller shall promptly replace such suspect/counterfeit parts with parts acceptable to the Buyer and the Seller shall be liable f or all costs relating to the removal and replacement of said parts as specified in the Subcontract requirements or Distributor's insurance policies. Buyer reserves all contractual rights and remedies to address grievances and detrimental impacts caused by suspect/counterfeit parts.

11.1.9 Goods Warranty; Anti-Counterfeit Mitigation

11.1.9.1 Seller warrants the Goods delivered pursuant to this Contract, unless specifically stated otherwise in this Contract, shall (i) be new; (ii) be and only contain materials obtained directly from the OM or an authorized OM reseller or distributor (Note - Independent Distributors (Brokers) shall not be used by Seller without written consent from Buyer); (iii) not be or contain Counterfeit Items; (iv) contain only authentic, unaltered OM labels and other markings; (v) have documentation made available upon request that authenticates traceability to the applicable OM; and (vi) be free from defects in workmanship, materials, and design and conform to all the specifications and requirements of this Subcontract. These warranties shall survive inspection, test, final acceptance and payment of Goods and Services.

11.1.9.2 For purposes of this section, a "Counterfeit Item" is defined to include, but is not limited to, (i) an item that is an illegal or unauthorized copy or substitute of an OM item; (ii) an item that does not contain the proper external or internal materials or components required by the OM or that is not constructed in accordance with OM specification; (iii) an item or component thereof that is used, refurbished or reclaimed but the Seller represents as being a new item; (iv) an item that has not successfully passed all OM required testing, verification, screening and quality control but that Seller represents as having met or passed such requirements; (v) an item with a label or other marking intended, or reasonably likely, to mislead a reasonable person into believing a non-OM item is a genuine OM item when it is not or (vi) material that has been confirmed to be a copy, imitation or substitute that has been represented, identified or marked as genuine, and/or altered by a source without legal right with intent to mislead, deceive or defraud.

11.1.9.3 Seller warrants that any hardware, software, and firmware Goods delivered under this Subcontract to the extent reasonably possible: (i) do not contain any viruses, malicious code, Trojan horse, worm, time bomb, self-help code, back door, or other software code or routine designed to (a) damage, destroy, or alter any software or hardware; (b) reveal, damage, destroy, or alter any data; (c) disable any computer program automatically; or (d) permit unauthorized access to any software or hardware; and (ii) do not contain any 3rd party software (including software that may be considered free software or open source software) that (a) may require any software to be published, accessed or otherwise made available without the consent of Buyer or

(b) may require distribution, copying or modification of any software free of charge;

11.1.9.4 This warranty entitlement shall inure to the benefit of both Buyer and Buyer's customer and shall cover a period 12 months following final acceptance; and,

11.1.9.5 Seller shall be liable for and save Buyer harmless from any loss, damage, or expense whatsoever that Buyer may suffer from the breach of any of these warranties. Remedies shall be at Buyer's election.

12.0 PERSONNEL

Not Applicable

CLAUSES INCORPORATED BY FULL TEXT

C-202-H001 ADDITIONAL DEFINITIONS–BASIC (NAVSEA) (OCT 2018)

(a) Department means the Department of the Navy.

(b) Commander, Naval Sea Systems Command means the Commander of the Naval Sea Systems Command of the Department of the Navy or his duly appointed successor.

(c) References to The Federal Acquisition Regulation (FAR) All references to the FAR in this contract shall be deemed to also reference the appropriate sections of the Defense FAR Supplement (DFARS), unless clearly indicated otherwise.

(d) National Stock Numbers Whenever the term Federal Item Identification Number and its acronym FIIN or the term Federal Stock Number and its acronym FSN appear in the contract, order or their cited specifications and standards, the terms and acronyms shall be interpreted as National Item Identification Number (NIIN) and National Stock Number (NSN) respectively which shall be defined as follows:

(1) National Item Identification Number (NIIN). The number assigned to each approved Item Identification under the Federal Cataloging Program. It consists of nine numeric characters, the first two of which are the National Codification Bureau (NCB) Code. The remaining positions consist of a seven digit nonsignificant number.

(2) National Stock Number (NSN). The National Stock Number (NSN) for an item of supply consists of the applicable four-position Federal Supply Class (FSC) plus the applicable nine-position NIIN assigned to the item of supply.

(End of text)

C-204-H001 USE OF NAVY SUPPORT CONTRACTORS FOR OFFICIAL CONTRACT FILES (NAVSEA) (OCT 2018)

(a) NAVSEA may use a file room management support contractor, hereinafter referred to as "the support contractor", to manage its file room, in which all official contract files, including the official file supporting this procurement, are retained. These official files may contain information that is considered a trade secret, proprietary, business sensitive or otherwise protected pursuant to law or regulation, hereinafter referred to as “protected information”. File room management services consist of any of the following: secretarial or clerical support; data entry; document reproduction, scanning, imaging, or destruction; operation, management, or maintenance of paper-based or electronic mail rooms, file rooms, or libraries; and supervision in connection with functions listed herein.

(b) The cognizant Contracting Officer will ensure that any NAVSEA contract under which these file room management services are acquired will contain a requirement that:

(1) The support contractor not disclose any information;

(2) Individual employees are to be instructed by the support contractor regarding the sensitivity of the official contract files;

(3) The support contractor performing these services be barred from providing any other supplies and/or services, or competing to do so, to NAVSEA for the period of performance of its contract and for an additional three years thereafter unless otherwise provided by law or regulation; and,

(4) In addition to any other rights the contractor may have, it is a third party beneficiary who has the right of direct action against the support contractor, or any person to whom the support contractor has released or disclosed protected information, for the unauthorized duplication, release, or disclosure of such protected information.

(c) Execution of this contract by the contractor is considered consent to NAVSEA's permitting access to any information, irrespective of restrictive markings or the nature of the information submitted, by its file room management support contractor for the limited purpose of executing its file room support contract responsibilities.

(d) NAVSEA may, without further notice, enter into contracts with other contractors for these services. Contractors should enter into separate non-disclosure agreements with the file room contractor. Contact the Procuring Contracting Officer for contractor specifics. However, any such agreement will not be considered a prerequisite before information submitted is stored in the file room or otherwise encumber the government.

C-211-H016 SPECIFICATIONS AND STANDARDS (NAVSEA) (OCT 2018)

(a) Definitions.

(i) A "zero-tier reference" is a specification, standard, or drawing that is cited in the contract (including its attachments).

(ii) A "first-tier reference" is either: (1) a specification, standard, or drawing cited in a zero-tier reference, or (2) a specification cited in a first-tier drawing.

(b) Requirements. All zero-tier and first-tier references, as defined above, are mandatory for use. All lower tier references shall be used for guidance only unless specifically identified below.

None

C-211-H018 APPROVAL BY THE GOVERNMENT (NAVSEA) (JAN 2019)

Approval by the Government as required under this contract and applicable specifications shall not relieve the Contractor of its obligation to comply with the specifications and with all other requirements of the contract, nor shall it impose upon the Government any liability it would not have had in the absence of such approval.

C-211-H019 COMMONALITY AND STANDARDIZATION (NAVSEA) (FEB 2022)

The Contractor shall develop and implement a Commonality and Standardization Plan, reducing range and increasing depth of like equipment, to enhance supportability, minimize life cycle costs, and increase system readiness and interoperability across ships/ship classes through the selection of equipment and components which are, to the maximum extent possible, (1) common for application within the Class and (2) common with equipment/components currently installed in U.S. Navy ships. The Contractor shall utilize both Industry (e.g., the Common Parts Catalog) and Government (e.g., NAVSEA Enterprise Commonality Virtual Shelf and the Hull, Mechanical and Electrical Equipment Data Research System (HEDRS)) tools to implement its Commonality and Standardization Plan. For selecting Hull Mechanical and Electrical (HM&E) equipment/components, the Contractor shall utilize NAVSEA Enterprise Commonality Virtual Shelf before other tools, if the items meet the contract requirements. The Virtual Shelf is a web-based repository of HM&E equipment/components that meet cross-platform requirements and specifications and provide superior Total Ownership Cost (TOC). Information to gain access to the Virtual Shelf is located on the following web site: https://www.pdrep.csd.disa.mil/

C-227-H014 PROTECTION OF DEPARTMENT OF NAVY TRADEMARKS - BASIC (NAVSEA) (JUL 2021)

(a) The contractor shall not assert any claim, in any jurisdiction, based on trademark or other name or design-based causes of action that are based on rights the contractor believes it has in the term(s) [contracting officers shall list terms(s) (Government assigned or approved nomenclature)] (the “Designation(s)”), against the Government or others authorized by the Government to use the Designation(s) (including the word(s), name, symbol, or design) acting within the scope of such authorization (i.e. claims for trademark infringement, dilution, trade dress infringement, unfair competition, false advertising, palming off, passing off, or counterfeiting). Such authorization shall be implied by the award of a Government contract to any party for the manufacture, production, distribution, use, modification, maintenance, sustainment, or packaging of the products and services identified under this contract, and the scope of such implied authorization is defined as the use of the Designation(s) in performance under such contract by the prime contractor and its subcontractors and suppliers at any tier. In all other cases, the scope of the authorization will be defined by the Government in writing.

(b) The contractor shall notify the contracting officer at least 30 days before asserting rights in, or filing an application to register, any one of the Designation(s) in any jurisdiction within the United States. Any such notification shall be in writing and shall identify the Designation(s) (including the word(s), name, symbol, or design), provide a statement as to its intended use(s) in commerce, and list the particular classes of goods or services in which registration will be sought.

C-233-H001 DOCUMENTATION OF REQUESTS FOR EQUITABLE ADJUSTMENT--BASIC (NAVSEA) (OCT 2018)

(a) For the purposes of this special contract requirement, the term "change" includes not only a change that is made pursuant to a written order designated as a "change order" but also (1) an engineering change proposed by the Government or by the Contractor and (2) any act or omission to act on the part of the Government in respect of which a request is made for equitable adjustment.

(b) Whenever the Contractor requests or proposes an equitable adjustment of $100,000 or more per vessel in respect to a change made pursuant to a written order designated as a "change order" or in respect to a proposed engineering change and whenever the Contractor requests an equitable adjustment in any amount in respect to any other act or omission to act on the part of the Government, the proposal supporting such request shall contain the following information for each individual item or element of the request:

(1) A description (i) of the work required by the contract before the change, which has been deleted by the change, and (ii) of the work deleted by the change which already has been completed. The description is to include a list of components, equipment, and other identifiable property involved. Also, the status of manufacture, procurement, or installation of such property is to be indicated. Separate description is to be furnished for design and production work. Items of raw material, purchased parts, components and other identifiable hardware, which are made excess by the change and which are not to be retained by the Contractor, are to be listed for later disposition;

(2) Description of work necessary to undo work already completed which has been deleted by the change;

(3) Description of work not required by the terms hereof before the change, which is substituted or added by the change. A list of components and equipment (not bulk materials or items) involved should be included. Separate descriptions are to be furnished for design work and production work;

(4) Description of interference and inefficiencies in performing the change;

(5) Description of each element of disruption and exactly how work has been, or will be disrupted:

(i) The calendar period of time during which disruption occurred, or will occur;

(ii) Area(s) aboard the vessel where disruption occurred, or will occur;

(iii) Trade(s) disrupted, with a breakdown of manhours for each trade;

(iv) Scheduling of trades before, during, and after period of disruption;

(v) Description of measures taken to lessen the disruptive effect of the change;

(6) Delay in delivery attributable solely to the change;

(7) Other work attributable to the change;

(8) Supplementing the foregoing, a narrative statement of the direct "causal" relationship between any alleged Government act or omission and the claimed consequences therefor, crossreferenced to the detailed information provided as required above; and

(9) A statement setting forth a comparative enumeration of the amounts "budgeted" for the cost elements, including the material costs, labor hours and pertinent indirect costs, estimated by the Contractor in preparing its initial and ultimate proposal(s) for this contract, and the amounts claimed to have been incurred and/or projected to be incurred corresponding to each such "budgeted cost" elements.

(c) Each proposal in excess of $100,000 submitted in support of a claim for equitable adjustment under any requirement of this contract shall, in addition to the information required by paragraph (b) hereof, contain such information as the Contracting Officer may require with respect to each individual claim item.

(d) It is recognized that individual claims for equitable adjustment may not include all of the factors listed in paragraph (b) above. Accordingly, the Contractor is required to set forth in its proposal information only with respect to those factors which are comprehended in the individual claim for equitable adjustment. In any event, the information furnished hereunder shall be in sufficient detail to permit the Contracting Officer to cross-reference the claimed increased costs, or delay in delivery, or both, as appropriate, submitted pursuant to paragraph (c) of this requirement, with the information submitted pursuant to paragraph (b) hereof.

C-247-H001 PERMITS AND RESPONSIBILITIES (NAVSEA) (DEC 2018)

The Contractor shall, without additional expense to the Government, be responsible for obtaining any necessary licenses and permits for complying with any applicable Federal, State, and Municipal laws, codes, and regulations for shipping and transportation including, but not limited to, any movement over public highways of overweight/over dimensional materials.

(End of text)

Section D - Packaging and Marking

D-211-H004 IDENTIFICATION MARKING OF PARTS--BASIC (NAVSEA) (OCT 2018)

For all parts not subject to the marking requirements in DFARS 252.211-7003 – Item Unique Identification and Valuation, marking shall be accomplished in accordance with the following:

(1) Parts shall be marked in accordance with generally accepted commercial practice.

(2) In cases where parts are so small as not to permit identification marking as provided above, such parts shall be appropriately coded so as to permit ready identification.

D-247-H002 PACKAGING OF SUPPLIES—BASIC (NAVSEA) (DEC 2020)

Item(s) 0001 The supplies furnished hereunder shall be packaged in accordance with ASTM-D-3951-18, Standard Practice for Commercial Packing.

D-247-H004 MARKING AND PACKING LIST(S) – BASIC (NAVSEA) (FEB 2022)

(a) Marking. Shipments, shipping containers and palletized unit loads shall be marked in accordance with ASTM-D-3951-18 approved 1 May 2018, Standard Practice for Commercial Packing.

(b) Packing List(s). A packing list (DD Form 250 Material Inspection and Receiving Report may be used) identifying the contents of each shipment, shipping container or palletized unit load shall be provided by the Contractor with each shipment. When a contract line item identified under a single stock number includes an assortment of related items such as kit or set components, detached parts or accessories, installation hardware or material, the packing list(s) shall identify the assorted items. Where assortment of related items is included in the shipping container, a packing list identifying the contents shall be furnished.

(c) Master Packing List. In addition to the requirements in paragraph (b) above, a master packing list shall be prepared where more than one shipment, shipping container or palletized unit load comprise the contract line item being shipped. The master packing list shall be attached to the number one container and so identified.

(d) Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number.

D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018)

The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use.

Section E - Inspection and Acceptance

INSPECTION AND ACCEPTANCE TERMS

Supplies/services will be inspected/accepted at:

CLAUSES INCORPORATED BY REFERENCE

Section F - Deliveries or Performance

DELIVERY INFORMATION

ANNE DEMIANIUK

NSWC PHILADELPHIA DIVISION

NSLC DETACHMENT

1601 LANGLEY AVE BLDG 542

PHILADELPHIA PA 19112

215-897-8844 FOB: Destination N64498

Section G - Contract Administration Data

252.232-7006 WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (DEC 2018)

(a) Definitions. As used in this clause—

“Department of Defense Activity Address Code (DoDAAC)” is a six position code that uniquely identifies a unit, activity, or organization.

“Document type” means the type of payment request or receiving report available for creation in Wide Area WorkFlow (WAWF).

“Local processing office (LPO)” is the office responsible for payment certification when payment certification is done external to the entitlement system.

“Payment request” and “receiving report” are defined in the clause at 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports.

(b) Electronic invoicing. The WAWF system provides the method to electronically process vendor payment requests and receiving reports, as authorized by Defense Federal Acquisition Regulation Supplement (DFARS) 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports.

(c) WAWF access. To access WAWF, the Contractor shall—

(1) Have a designated electronic business point of contact in the System for Award Management at https://www.sam.gov; and

(2) Be registered to use WAWF at https://wawf.eb.mil/ following the step-by-step procedures for self-registration available at this web site.

(d) WAWF training. The Contractor should…