N4215823R0006 BLAST POT COMBINED.pdf

This is a COMBINED SYNOPSIS/SOLICITATION for commercial items prepared in accordance with FAR Part 12, Acquisition of Commercial Items and FAR Part 13, Simplified Acquisition Procedures as supplemented with the additional information included in this notice. This combined synopsis/solicitation SHALL be posted on SAM.gov

The RFQ number is N4215823R0006.

It is the responsibility of the vendor to be familiar with the applicable clauses and provisions. The clauses may be accessed in full text at these addresses: https://www.acquisition.gov/browse/index/far and http://www.acq.osd.mil/dpap/dars/dfarspgi/current/index.html

The requirement: small business set aside, the Small Business Office concurs with the determination.

Requirement is issued by Norfolk Naval Shipyard (NNSY)

Acquisition is: Unrestricted

The NAICS code: 532490 and the Small Business Standard is $40.0 million.

Method of Solicitation: RFQ

Offer issue due: August 31, 2023 10:00am, EST

The contractor is required to sign this document and return copies to the issuing office. Contractor agrees to furnish and deliver all items set forth or otherwise Identified above and on any additional sheets subject to the terms and conditions specified.

Naval Sea Systems Command (NAVSEA) requires vendors capable of providing all required services, labor, material and equipment necessary to successfully supply the rental of two (2) 4 person COMPACT blast pots to include a transfer hopper (common trade name: Puker) and 6 Safety Tote Bins (common trade name: Grit Bins).

See incorporated RFQ and Statement of Work (SOW).

Quotes must be submitted via email to theresa.m.clark36.civ@us.navy.mil and courtney.t.woodley.civ@us.navy.mil Thursday August 30, 2023 at 1000 a.m. EST and must include the four mandatory clauses FAR 52.203-18, 52.204-24, and 52.209-11 to be considered for award.

If there are any questions, please contact Ms. Theresa Clark or Mrs. Courtney Woodley who can be reached at email theresa.m.clark36.civ@us.navy.mil and courtney.t.woodley.civ@us.navy.mil.

The Government will award on the basis of price and providing equipment by POP date stated in SOW unless the contracting officer is aware of past performance information related to the low price quote/offer which indicates that quote/offer may not represent best value.

In that case, the Government reserves the right to consider the past performance of other quotes/offers, conduct a price, past performance tradeoff, and award to other than the lowest price quote/offer.

System for Award Management (SAM). Quoters must be registered in the SAM database to be considered for award. Registration is free and can be completed on-line at http://www.sam.gov/.

All quotes shall include price(s), FOB point, a point of contact, name and phone number, email, GSA contract number if applicable, business size, and payment terms.

Each response must clearly indicate the capability of the quoter to meet all specifications and requirements.

SEND Quotes and Questions directly to EMAIL Addresses at theresa.m.clark36.civ@us.navy.mil and courtney.t.woodley.civ@us.navy.mil.

https://www.acquisition.gov/browse/index/far http://www.acq.osd.mil/dpap/dars/dfarspgi/current/index.html

N4215823R0006

Section SF 1449 - CONTINUATION SHEET

INSTRUCTIONS TO OFFERS

INSTRUCTIONS TO OFFERORS – COMMERCIAL ITEMS

This requirement will be prepared in accordance with the information in FAR Subpart 12.6 and FAR Part 13, as supplemented with additional information included in this notice. Accordingly, a Simplified Streamlined acquisition process will be used in the evaluation and award of the contract.

Quotes are due on or before 8/31/2023 at 10:00AM, Eastern. Quotations shall be emailed to Contract Specialist, Theresa Clark, theresa.m.clark36.civ@us.navy.mil and to Courtney Woodley, courtney.t.woodley.civ@us.navy.mil . Questions for clarification must be submitted by 8/31/2023 at 10:00AM, Eastern.

*REQUIRED DOCUMENTS

Technical Acceptability will be evaluated to determine an overall rating of “acceptable” or “unacceptable”. This will be determined by evaluating the ability of the vendor to provide equipment that that meets all specifications and delivery requirements. It is the contractor’s responsibility to ensure that their quotation clearly demonstrates their ability to meet the requirements.

Quoters may propose on one/some/all of the items identified.

Unless specifically stated otherwise, submission of a quote means the quoter agrees to partial contract award.

The completion and submission of the above items will constitute a quote and will be considered the vendor's unconditional assent to the terms and conditions of this solicitation and any attachments and/or exhibits.

Failure to provide all of these documents by the required date and time may preclude a quotation from award consideration at the discretion of the Government.

Quotations shall be valid for 30 days.

Quotations will consist of the following documents submitted together in Adobe Acrobat .pdf format:

Period of Performance as follows: September 15, 2023 – September 15, 2024

AS PROVIDED IN SECTION F OF THIS DOCUMENT

Completed and signed standard form SF1449 with unit prices for each line item in accordance with the Contract Line Item Number (CLIN).

Provide daily, weekly, and monthly (30 days) rates for CLIN 0001

Additionally, each offeror must provide the following information with the quote:

1. The Request for Quotes (RFQ) number;

2. The Name, Address, Telephone Number, and Cage Code or Unique Entity ID number of the offeror;

3. Include a statement specifying the extent of agreement with all terms, conditions, and provisions included in the RFQ. Proposals that reject the terms and conditions of the RFQ may be excluded from consideration;

4. Acknowledgment of Solicitation Amendments (SF-30), if any;

5. Completed FAR 52.212-3 Representations and Certifications unless otherwise completed in SAM;

mailto:theresa.m.clark36.civ@us.navy.mil mailto:courtney.t.woodley.civ@us.navy.mil

6. Confirmation of the ability to meet the period of performance as contained herein;

7. Provide a technical description of the items being offered in sufficient detail to evaluate compliance with the requirements in the solicitation. Technical Submission including but not limited to equipment specifications, manuals, and photographs;

8. TECHNICAL CAPABILITY/CONTRACTOR / RESPONSIBLITY CERTIFICATION STATEMENT

Vendor shall certify for equipment being quoted that his product meets each capability listed below by initialing at the bottom. In order to be considered for award, this must be completed and submitted with your quote.

Vendor hereby certifies that his/her service meets or exceeds all specifications in this solicitation and found within Attachment 1, in their entirety, with no exceptions. ________________________ (Initial)

Award will be made for the technically acceptable item or combination of technically acceptable items that result in the lowest aggregate price to the Government.

Award may or may not be made without any type of discussions or negotiations. This is based on the Contracting Officer’s determination after an evaluation has been completed on all quotations.

Technical Acceptability: Technical Acceptability will be evaluated to determine an overall rating of “acceptable” or “unacceptable”. This will be determined by evaluating the ability of the vendor to provide equipment that meets all requirements and demonstrates a thorough knowledge and understanding of the Specification requirements. It is the contractor’s responsibility to ensure that their quotation clearly demonstrates their ability to perform these requirements. Technical acceptability will be defined as follows:

Technical Ratings

Rating Description Acceptable Quote meets all of the requirements identified Unacceptable Quote does not meets all of the requirements identified

Failure to meet any technical requirement for an item (or specification) will make the quotation unacceptable for that item (or that specification).

If an item (or specification) is technically unacceptable, its price will not be considered for award.

Price:

The estimated amount for each line item will be added together to determine the total estimated price which will become the evaluation price.

The vendor’s proposed price will be evaluated on the basis of price reasonableness. All prices must be considered fair and reasonable as determined by the Government. All quotes submitted in response to this solicitation shall stand firm for 30 calendar days from the response date of this solicitation.

The completion and submission of the above items will constitute a quote and will be considered the vendor’s unconditional assent to the terms and conditions of this Solicitation and any attachments and/or exhibits.

Failure to provide all of these documents by the required date and time may preclude a quotation from award consideration at the discretion of the Government.

EVALUATION

FAR 52.212-2, Evaluation — Commercial Items is applicable to this procurement. The Government will award a contract resulting from this Request for Quotation (RFQ) to the responsible quoter whose quotation conforms to the RFQ and will be the most advantageous to the Government, price and other factors considered.

The following factors shall be used to evaluate quotations:

1. Technical Capability;

2. Delivery;

3. Price

Technical acceptability will be determined by reviewing the technical certifications submitted for each item to ensure that all of the technical requirements identified are met. Technical acceptability will be defined as follows:

Technical Evaluation Ratings Rating Description Acceptable Quote meets all of the requirements identified.

Unacceptable Quote does not meet all of the requirements identified.

Contractors who fail to possess acceptable technical capability will not be considered for award and the other elements of their quotation will not be evaluated.

Price: The vendor’s proposed price will be evaluated on the basis of price reasonableness. All prices must be considered fair and reasonable as determined by the Government.

For purposes of award amongst all of the technically acceptable quotations, delivery schedule will be considered to be of equal importance when compared to price.

NOTE: Quotations determined to be technically unacceptable shall not be further evaluated for award. Of the technically acceptable quotations, the Government reserves the right to award to other than low based upon a selection determined to be the best value to the Government, price and other factors considered.

Although price is considered to be equal in importance to delivery, it has the potential to become more significant during the evaluation process. The importance of price will increase as the degree of equity in a respondent’s non-cost quotations rise. The importance of price will also increase when a quotation’s price is so significantly high as to diminish the value to the Government that might have been gained under the other aspects of the quotation. If at any point in the evaluation all respondents are determined to have submitted equal or generally equivalent non-cost quotations, price may become the factor in determining the contractor selected for award.

The quoted prices of all technically acceptable items will be evaluated and the contracting officer shall assume, for the purpose of making multiple awards, that $500 would be the administrative cost to the Government for issuing and administering each contract awarded under this Request for Quotations.

Individual awards shall be for the items or combinations of items that result in the lowest aggregate cost to the Government, including the assumed administrative costs.

The solicitation was amended on 28 October 2022 to extend the closing date/receipt of offers to 31 October 2022.

The solicitation was amended on 31 October 2022 to answer questions received, to indicate consideration for split awards, and to extend the closing date/receipt of offers to 2 November 2022.

TECHNICAL CAPABILITY

See below for: TECHNICAL CAPABILITY/CONTRACTOR / RESPONSIBLITY CERTIFICATION

STATEMENT

Vendor shall certify for equipment being quoted that his product meets each capability listed below by initialing at the bottom. In order to be considered for award, this must be completed and submitted with your quote.

PURPOSE OF REQUEST: SERVICE RENTAL FROM VENDOR TO PROVIDE: Supply 2 two (2) 4 person COMPACT blast pots to include a transfer hopper (common trade name: Puker) and 6 Safety Tote Bins (common trade name: Grit Bins)

Technical Capabilities Statement Item #0001 Specifications for Blast Pot Shall be provided with the following capabilities, features, and specifications: YES NO

• Weigh approx. 7200 lbs. empty.

• Required dimensions: 9’5” L x 8’4” W x 10’6” OAH to due limited dry dock laydown area.

• Must have a high volume abrasive storage hopper with even-fill loading system.

• Certified top crane lift pads eyes.

• 500 MCM Crimp Tube Series E1022 male cam loc fittings.

• Oversized forklift pockets of 5.5” H x 11.5” W full open pockets.

• 4 each quick open access manways with permanent internal ladder. One over each pot. *These manways will NOT REQUIRE tools to open and must allow for lock out/tag out.*

• Integrated High Volume abrasive loading piping with a quad diffuser on the abrasive transfer loading system.

• Must have an internal venting system to allow for blast pot blowdown to be directed into hopper

• Must have a single 6” compressed air manifold with moisture trap and rupture disk overpressure protection for blast pots.

• Must have Top hopper toe rails with removable side access ladder and OSHA regulation removable handrails with spring loaded safety access gate for top hopper access. Hand rail pockets will be made of stainless steel.

• Main power supply panel will be made of stainless steel and front disconnect with lock out/tag out feature and the panel must work with 110 VAC and supply 24VDC to the Blaster Control Panel.

• Must come with separate (from the higher voltage main power panel) control panel for all blast controls, (Trade name: blaster control panel) 24VDC and must include the following features:

1. Indicator lights for “Air On/off”, “Grit On/off”, and “Deadman switch on.”

2. Remote abrasive adjustment at the panel.

3. Four wire Deadman controls with remote choke and blowdown at the blast nozzle.

4. Remote choke and blowdown at the panel.

5. Full open Bigmouth choke feature to open grit valve to full open for choke.

6. Must have a “deny start” safety feature if deadman switch is on when panel is energized.

7. Power feed for LED blast lights

8. Independent blast light flicker operation for communications between pot operator and sandblaster.

• The four (4) blast Pots will be of 30” high capacity/90% abrasive fill blast opts and contain the following features: 1. Cone bottom with 175 PSI pressure rating.

• 2. Oversized 1 ½” high flow compressed air piping.

• 3. Full port 7” power popup plunger with manual close for maintenance when hopper is full of abrasives.

• 4. 1 ½ Schmidt Thompson II abrasive metering valves.

• 5. Separate combo valves to pressurize pot independent from the blast air valve.

• 6. Individual high flow regulators for each pot to allow for each blaster to operate at pressures independent of the other pots.

• 7. Pot depressurization directly in to blast hopper and not to atmosphere.

Vendor shall certify for equipment being quoted that his product meets each capability listed below by initialing at the bottom. In order to be considered for award, this must be completed and submitted with your quote.

PURPOSE OF REQUEST: SERVICE RENTAL FROM VENDOR TO PROVIDE: Supply 2 two (2) 4 person COMPACT blast pots to include a transfer hopper (common trade name: Puker) and 6 Safety Tote Bins (common trade name: Grit Bins)

Item #0001 Specifications for ABRASIVE TRANSFER HOPPER/SYSTEM (TRADE NAME:

PUKER)

Shall be provided with the following capabilities, features, and specifications: YES NO

• Weight: ~950 Lbs. Empty

• Overall Dimensions: 55” L x 56” W x 50” OAH

• 8.5 cubic foot storage capacity.

• Hinged lid

• 500 MCM Crimp Tube Series E1022 male cam loc fittings

• Oversized forklift pockets to measure 3.5” H x 9.5” W full open

• Stainless steel control panel for all transfer controls, 24VDC. Transfer control panel connects to blast control panel for power. Transfer control panel will include:

1. Indicator lights for high and low level in vessel and transferring.

2. Controls for automatic transfer.

• The abrasive transfer pot must be/include:

1. 1.5 cubic foot

2. 1 inch oversize air piping

3. Full port 6 inch power popup plunger with manual close for maintenance when hopper is full of abrasives.

4. Individual regulator rated for 175 PSI.

5. Cone bottom.

Vendor shall certify for equipment being quoted that his product meets each capability listed below by initialing at the bottom. In order to be considered for award, this must be completed and submitted with your quote.

PURPOSE OF REQUEST: SERVICE RENTAL FROM VENDOR TO PROVIDE: 6 Safety Tote Bins (common trade name: Grit Bins)

Item #0001 Specifications for ABRASIVE SAFTERY TOTES (TRADE NAME: GRIT BINS) Shall be provided with the following capabilities, features, and specifications: YES NO

• Overall dims: 48” L x 48” W x 71” OAH

• 55 cubic foot storage capacity of non-steel abrasives.

• weight: ~950 Lbs.

• Certified top crane lift pad eyes.

• Hinged weather proof access cover 18 inch x 14 inch.

• Max abrasive capacity of 8,000 lbs.

• 4 way fork lift pockets to measure 3.35 inch x 9.5 inch heavy duty

• both 1 ¼ inch vent and fill pipe

• Stackable design

• 6 inch paddle gate

SOW

Statement of Work Rental of Two (2) 4 Person COMPACT Sandblasting Pot to include an Abrasive Transfer Hopper (Common trade name: Puker) and 6 safety tote bins (Common trade name: Grit Bins) for 77E Project Section A: Scope

1. Objective:

NNSY Preservation Dept. requires the rental of two (2) 4 person COMPACT blast pots to include a transfer hopper (common trade name: Puker) and 6 Safety Tote Bins (common trade name: Grit Bins) for the life of 77E Project.

2. Background/Introduction NNSY Preservation Dept. does not own the above type of blast pot and shop 71 cannot support project 77E current request.

3. Limitations of Work NONE Section B: Applicable Documents: NONE

4. Documentation: NONE.

Section C: Requirements

5. Scope of Work:

NNSY Preservation Dept. requires the rental of two (2) 4 person COMPACT blast pots to include a transfer hopper (common trade name: Puker) and 6 Safety Tote Bins (common trade name: Grit Bins) for the life of 77E Project.

6. Contractor Responsibilities:

-Supply 2 two (2) 4 person COMPACT blast pots to include a transfer hopper (common trade name: Puker) and 6 Safety Tote Bins (common trade name: Grit Bins) See Equipment Specifications section 10.

- Delivery drivers/pickup drivers/any visiting onsite vendors have to be able to obtain security clearance to access NNSY and or the controlled industrial area (CIA) (Attachment B – Security Access - DBIDs).

- Equipment delivery and removal.

- When the equipment is required to be removed to the contractor's facility for repair or replacement, the contractor shall be responsible for loss or damage, from the time it leaves the government site until it is returned to the government site.

- Clean all equipment prior to delivery or upon return:

Equipment shall be cleaned to a degree of cleanliness that results in a surface free of grease, oil, flux, scale, dirt, loose particles and any other matter foreign to the base metal. Adherent light superficial rust on steel surfaces, caused by short time exposure to the atmosphere, is acceptable.

- The contractor shall dispatch a representative in response to a service request to repair and/or replace any equipment within six (6) hours of notification by NNSY.

- Equipment must have pad eyes for crane movement and forklift slots (capable of being moved with forklift).

- The weight of all equipment must be stenciled on the unit.

- New or used equipment may be provided. NNSY reserves the right to inspect the proposed equipment prior to contract award.

- The equipment will be exposed to everyday weather and saltwater air. It is the contractor's responsibility to provide any protective covering for the units.

- The government reserves the right to return one or all units at any time prior to the expiration of the rental period. The contractor shall agree to prorate costs for the time the units are in use by NNSY only.

7. NNSY Responsibilities:

- 1. Provide operators

- 2. Perform basic maintenance and monitor all gauges.

- 3. Equipment movements at the job site.

- 4. Lost items and equipment damage beyond normal wear and tear.

-5. Give the contractor twenty-four (24) hour notice for return of units prior to expiration of rental period.

8. Government Furnished Property: NONE

9. Security Requirements:

Per FAR 22.102-1(a) entitled "Safety", Contractors are hereby informed that their employees or representatives present on property under Norfolk Naval Shipyard cognizance must follow Federal and State OSHA requirements OSHE OSHECM Chapter Hazardous Energy Control (HEC) requirements or safety requirements for site specific location of the of the contract.

Contractors and Non-NNSY Government Agencies (NNGAs) are hereby informed that their employees or representatives present on property under Norfolk Naval Shipyard (NNSY) cognizance must adhere to Federal OSHA requirements for hazardous energy control IAW 29 CFR 1915.89 and must follow Hazardous Energy Control (HEC) procedures as identified in NAVSEA’s Occupational Safety, Health, and Environment Corporate Manual (OSHECM) Chapter 250 (latest revision), when performing work under NNSY contract. All HEC work to be performed by Contractors and NNGAs requires that NNSY Technical Points of Contact (TPOCs) and/or Contracting Officer’s Representatives (CORs) be notified of the HEC scope of work prior to starting work. Any changes or deviations in the initial scope of HEC work requires the NNSY TPOCs and/or CORs be informed of the change/deviation. Appendix 250.B-1 through B-3 of OSHECM Chapter 250 for multiple employer work identifies when Contractors and NNGAs are required to assign their Lockout/Tags-Plus Coordinator (LOTC) to coordinate HEC work with the cognizant NNSY LOTC. HEC locks shall be provided by the contractor or NNGA for their employees use. The HEC locks shall have red bodies with name labels or name tags affixed, identifying who installed the HEC lock(s) and a point of contact telephone number. HEC lock name labels and tags must be made of materials that will hold up to the environment to which they are exposed. HEC tags used for Tags-Plus HEC work shall be provided by the cognizant NNSY LOTC to the contractor or NNGA for their use if machinery, equipment, or systems (MES) cannot be locked out. OSHECM Chapter 250 Tags-Plus procedures will be strictly followed.

Contractors and NNGAs may obtain electronic copies of OSHECM Chapter 250 (latest revision) and access the OSHA 1915.89 web site by using the following link to NNSY’s public access web site: http://www.navsea.navy.mil/shipyards/norfolk/default.aspx http://www.navsea.navy.mil/shipyards/norfolk/default.aspx

Names and contact information for NNSY LOTCs and/or the Building Monitor will be provided by NNSY TPOC and/or CORs set forth elsewhere in this award document.

10. Equipment Specifications:

BLAST POT

-Weigh approx. 7200 lbs. empty.

-Required dimensions: 9’5” L x 8’4” W x 10’6” OAH to due limited dry dock laydown area.

-Must have a high volume abrasive storage hopper with even-fill loading system.

-Certified top crane lift pads eyes.

- 500 MCM Crimp Tube Series E1022 male cam loc fittings.

-Oversized forklift pockets of 5.5” H x 11.5” W full open pockets.

-4 each quick open access manways with permanent internal ladder. One over each pot. *These manways will NOT REQUIRE tools to open and must allow for lock out/tag out.* -Integrated High Volume abrasive loading piping with a quad diffuser on the abrasive transfer loading system.

-Must have an internal venting system to allow for blast pot blowdown to be directed into hopper.

-Must have a single 6” compressed air manifold with moisture trap and rupture disk overpressure protection for blast pots.

-Must have Top hopper toe rails with removable side access ladder and OSHA regulation removable handrails with spring loaded safety access gate for top hopper access. Hand rail pockets will be made of stainless steel.

-Main power supply panel will be made of stainless steel and front disconnect with lock out/tag out feature and the panel must work with 110 VAC and supply 24VDC to the Blaster Control Panel.

-Must come with separate (from the higher voltage main power panel) control panel for all blast controls, (Trade name: blaster control panel) 24VDC and must include the following features:

1. Indicator lights for “Air On/off”, “Grit On/off”, and “Deadman switch on.”

2. Remote abrasive adjustment at the panel.

3. Four wire Deadman controls with remote choke and blowdown at the blast nozzle.

4. Remote choke and blowdown at the panel.

5. Full open Bigmouth choke feature to open grit valve to full open for choke.

6. Must have a “deny start” safety feature if deadman switch is on when panel is energized.

7. Power feed for LED blast lights

8. Independent blast light flicker operation for communications between pot operator and sandblaster.

-The four (4) blast Pots will be of 30” high capacity/90% abrasive fill blast opts and contain the following features:

1. Cone bottom with 175 PSI pressure rating.

2. Oversized 1 ½” high flow compressed air piping.

3. Full port 7” power popup plunger with manual close for maintenance when hopper is full of abrasives.

4. 1 ½ Schmidt Thompson II abrasive metering valves.

5. Separate combo valves to pressurize pot independent from the blast air valve.

6. Individual high flow regulators for each pot to allow for each blaster to operate at pressures independent of the other pots.

7. Pot depressurization directly in to blast hopper and not to atmosphere.

ABRASIVE TRANSFER HOPPER/SYSTEM (TRADE NAME: PUKER) SHALL BE:

-Weight: ~950 Lbs. Empty -Overall Dimensions: 55” L x 56” W x 50” OAH -8.5 cubic foot storage capacity.

-Hinged lid

- 500 MCM Crimp Tube Series E1022 male cam loc fittings -Oversized forklift pockets to measure 3.5” H x 9.5” W full open -Stainless steel control panel for all transfer controls, 24VDC. Transfer control panel connects to blast control panel for power. Transfer control panel will include:

1. Indicator lights for high and low level in vessel and transferring.

2. Controls for automatic transfer.

-The abrasive transfer pot must be/include:

1. 1.5 cubic foot

2. 1 inch oversize air piping

3. Full port 6 inch power popup plunger with manual close for maintenance when hopper is full of abrasives.

4. Individual regulator rated for 175 PSI.

5. Cone bottom.

ABRASIVE SAFTERY TOTES (TRADE NAME: GRIT BINS) SHALL BE:

-Overall dims: 48” L x 48” W x 71” OAH -55 cubic foot storage capacity of non-steel abrasives.

-weight: ~950 Lbs.

-Certified top crane lift pad eyes.

-Hinged weather proof access cover 18 inch x 14 inch.

-Max abrasive capacity of 8,000 lbs.

-4 way fork lift pockets to measure 3.35 inch x 9.5 inch heavy duty -both 1 ¼ inch vent and fill pipe -Stackable design -6 inch paddle gate

11. Delivery Terms/Shipping/Transportation:

All units will be delivered to Norfolk VA, Naval Operating Base (NOB) Bldg. W-130 Staging Area

12. Place of Performance/Delivery Location:

Norfolk Va., Naval Operating Base (NOB) Portsmouth Va., Norfolk Naval Shipyard

13. Period of Performance (PoP)/ Completion Date/ Delivery Date:

REQUESTED START: 15 SEP 2023

FINISH: 14 SEP 2024

Section D: Contact Information

14. Technical POC:

TBD

15. Invoice Certifier:

TBD

Section E: Lifting and Rigging Requirements:

For multiple point lifts each lifting attachment shall be capable of supporting one half the gross weight of the equipment with a design factor of five to one based on ultimate strength.

For multiple point lifts each lifting attachment shall be designed to accept a standard anchor shackle (Federal Specification RR-C-271D, type IVA) which is capable of supporting one half the gross weight of the equipment. For single point lifts the lifting attachment shall be designed to accept a standard anchor shackle (Federal Specification RR-C-271D, type IVA) which is capable of supporting the gross weight of the equipment.

Design of the lifting attachments shall be such that the attachments and shackles are not side loaded more than 10 degrees out of the plane. Lifting attachments shall be located such that the lifting slings do not contact the equipment, or alternatively a spreader beam certified to NAVFAC P-307 shall be provided. Whenever practical, the lifting attachments shall be located above the center of gravity, and such that the lifting slings do not contact the equipment housings.

Each lifting attachment shall be conspicuously marked in a contrasting color “Lift Here”. Letters shall have a minimum height of 1”.

The equipment shall be marked in a prominent location with the gross weight. Sand hoppers, tubs, or other containers that may contain material shall be marked with the empty and full weight (or alternatively the empty weight and working load limit). Marking shall be upper case letters of a contrasting color, with a minimum height of 1”. Marking shall include the units (i.e.

“pounds”, “long tons”, etc.).

The equipment shall be provided with a lifting sketch/ rigging diagram that meets the requirements of NAVFAC-P-307.

The lifting sketch shall detail any specific requirements and / or configurations that must be meet prior to lifting (i.e. “engage swing lock”, Tilt mast back fully”, “Rotate lifting basket over side”, “Utilize 10’ minimum length slings”, Spreader beam required”, etc.

The lifting sketch shall include the locations of the center of gravity of the equipment (full fuel, hydraulic tanks, etc.), equipment model/manufacturer, and gross weight.

A copy of the lifting sketch shall be permanently posted on the equipment, and a copy shall be forwarded to Code 714.

RIGGING SKETCH/DRAWINGS REQUIREMENTS:

Rigging sketches, as a minimum, shall identify the following:

1. The Weight of the load

2. The location of the center of gravity.

3. The minimum crane capacity.

4. The minimum capacity/ length of slings.

5. The minimum capacity of other standard rigging gear.

6. The attachment (lifting) points for the load.

(a) The attachment points for multiple leg lifts shall be sized such that each attachment point can support half the load’s weight at the anticipated lift angle.

(b) The attachment point for single leg lifts shall be sized such that the attachment point can support the entire load’s weight.

7. Limitations on allowable orientation for any parts making up the lifting assembly.

8. For single leg vertical lifts using twisted rope (wire or synthetic), two parallel ropes each capable of supporting the entire load alone shall be required unless a method is used to prevent unlaying the rope.

9. A minimum D/d ratio of one shall be required where wire rope slings pass over any object, or in the eyes of wire rope slings. A minimum D/d ratio of two shall be required where synthetic rope slings pass over any object, or in the eyes of synthetic rope slings.

(a) “D” represents the diameter of the object the sling passes over.

(b) “d” represents the diameter of the sling.

(c) Table 14-2 of NAVFAC P-307 lists efficiency factors at various D/d ratios.

10. Components in each handling assembly shall be sized based on the worst case distribution of loads.

11. When nonstandard gear is required (i.e. round stock lifting bars) written instructions shall be provided that ensure:

(a) The proper material is being used.

(b) The item is certified IAW NAVFAC P-307.

(c) Any special requirements or dimensions are followed to ensure that engineering assumptions are met (i.e. eccentricity)

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

0001 2 Unit

CARRYOVER RENTAL OF BLAST POTS IAW SOW

FFP

RENTAL OF BLAST POTS IN ACCORDANCE WITH THE STATEMENT OF

WORK

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

FOB: Destination

MILSTRIP: N4215823RC30971

PURCHASE REQUEST NUMBER: N4215823RC30971

PSC CD: W039

NET AMT

INSPECTION AND ACCEPTANCE TERMS

Supplies/services will be inspected/accepted at:

CLIN INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY

0001 Destination Government SEE SCHEDULE

SEE SCHEDULE

AS SPECIFIED VA 23511

Government

DELIVERY INFORMATION

CLIN DELIVERY DATE QUANTITY SHIP TO ADDRESS DODAAC /

CAGE

0001 15-SEP-2023 2 NAVAL STATION NORFOLK (NOB)

SEE STATEMENT OF WORK FOR

PLACE OF PERFORMANCE

NORFOLK VA 23511

TEL: SEE SOW

FOB: Destination

N00189

CLAUSES INCORPORATED BY REFERENCE

52.203-3 Gratuities APR 1984 52.204-7 System for Award Management OCT 2018 52.204-13 System for Award Management Maintenance OCT 2018 52.204-16 Commercial and Government Entity Code Reporting AUG 2020 52.204-22 Alternative Line Item Proposal JAN 2017 52.204-24 Representation Regarding Certain Telecommunications and

Video Surveillance Services or Equipment

NOV 2021

52.209-10 Prohibition on Contracting With Inverted Domestic Corporations

NOV 2015

52.212-1 Instructions to Offerors--Commercial Products and Commercial Services

MAR 2023

52.212-2 Evaluation - Commercial Items NOV 2021 52.222-35 Equal Opportunity for Veterans JUN 2020 52.222-37 Employment Reports on Veterans JUN 2020 52.225-1 Buy American--Supplies OCT 2022 52.225-13 Restrictions on Certain Foreign Purchases FEB 2021 52.232-39 Unenforceability of Unauthorized Obligations JUN 2013 52.247-34 F.O.B. Destination NOV 1991 252.201-7000 Contracting Officer's Representative DEC 1991 252.203-7000 Requirements Relating to Compensation of Former DoD

Officials

SEP 2011

252.203-7002 Requirement to Inform Employees of Whistleblower Rights DEC 2022 252.203-7005 Representation Relating to Compensation of Former DoD

Officials

SEP 2022

252.204-7008 Compliance With Safeguarding Covered Defense Information Controls

OCT 2016

252.204-7015 Notice of Authorized Disclosure of Information for Litigation Support

JAN 2023

252.209-7004 Subcontracting With Firms That Are Owned or Controlled By The Government of a Country that is a State Sponsor of Terrorism

MAY 2019

252.211-7003 Item Unique Identification and Valuation JAN 2023 252.225-7012 Preference For Certain Domestic Commodities APR 2022 252.225-7048 Export-Controlled Items JUN 2013 252.232-7003 Electronic Submission of Payment Requests and Receiving

Reports

DEC 2018

252.232-7010 Levies on Contract Payments DEC 2006 252.243-7002 Requests for Equitable Adjustment DEC 2022

252.244-7000 Subcontracts for Commercial Products or Commercial Services

JAN 2023

252.247-7023 Transportation of Supplies by Sea JAN 2023

CLAUSES INCORPORATED BY FULL TEXT

52.204-26 COVERED TELECOMMUNICATIONS EQUIPMENT OR SERVICES--REPRESENTATION (OCT

2020)

(a) Definitions. As used in this provision, “covered telecommunications equipment or services” and "reasonable inquiry" have the meaning provided in the clause 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment.

(b) Procedures. The Offeror shall review the list of excluded parties in the System for Award Management (SAM) (https://www.sam.gov) for entities excluded from receiving federal awards for “covered telecommunications equipment or services”.

(c) Representations.

(1) The Offeror represents that it [ ___ ] does, [ ___ ] does not provide covered telecommunications equipment or services as a part of its offered products or services to the Government in the performance of any contract, subcontract, or other contractual instrument.

(2) After conducting a reasonable inquiry for purposes of this representation, the offeror represents that it [ ___ ] does, [ ___ ] does not use covered telecommunications equipment or services, or any equipment, system, or service that uses covered telecommunications equipment or services.

(End of provision)

52.212-3 OFFEROR REPRESENTATIONS AND CERTIFICATIONS--COMMERCIAL PRODUCTS AND

COMMERCIAL SERVICES (DEC 2022)

The Offeror shall complete only paragraph (b) of this provision if the Offeror has completed the annual representations and certification electronically in the System for Award Management (SAM) accessed through https://www.sam.gov. If the Offeror has not completed the annual representations and certifications electronically, the Offeror shall complete only paragraphs (c) through (v) of this provision.

(a) Definitions. As used in this provision --

"Covered telecommunications equipment or services" has the meaning provided in the clause 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment.

"Economically disadvantaged women-owned small business (EDWOSB) concern" means a small business concern that is at least 51 percent directly and unconditionally owned by, and the management and daily business operations of which are controlled by, one or more women who are citizens of the United States and who are economically disadvantaged in accordance with 13 CFR part 127, and the concern is certified by SBA or an https://www.sam.gov/ approved third-party certifier in accordance with 13 CFR 127.300. It automatically qualifies as a women-owned small business eligible under the WOSB Program.

"Forced or indentured child labor" means all work or service-

(1) Exacted from any person under the age of 18 under the menace of any penalty for its nonperformance and for which the worker does not offer himself voluntarily; or

(2) Performed by any person under the age of 18 pursuant to a contract the enforcement of which can be accomplished by process or penalties.

"Highest-level owner" means the entity that owns or controls an immediate owner of the offeror, or that owns or controls one or more entities that control an immediate owner of the offeror. No entity owns or exercises control of the highest level owner.

"Immediate owner" means an entity, other than the offeror, that has direct control of the offeror. Indicators of control include, but are not limited to, one or more of the following: Ownership or interlocking management, identity of interests among family members, shared facilities and equipment, and the common use of employees.

"Inverted domestic corporation" means a foreign incorporated entity that meets the definition of an inverted domestic corporation under 6 U.S.C. 395(b), applied in accordance with the rules and definitions of 6 U.S.C. 395(c).

"Manufactured end product" means any end product in product and service codes (PSCs) 1000-9999, except--

(1) PSC 5510, Lumber and Related Basic Wood Materials;

(2) Product or Service Group (PSG) 87, Agricultural Supplies;

(3) PSG 88, Live Animals;

(4) PSG 89, Subsistence;

(5) PSC 9410, Crude Grades of Plant Materials;

(6) PSC 9430, Miscellaneous Crude Animal Products, Inedible;

(7) PSC 9440, Miscellaneous Crude Agricultural and Forestry Products;

(8) PSC 9610, Ores;

(9) PSC 9620, Minerals, Natural and Synthetic; and

(10) PSC 9630, Additive Metal Materials.

"Place of manufacture" means the place where an end product is assembled out of components, or otherwise made or processed from raw materials into the finished product that is to be provided to the Government. If a product is disassembled and reassembled, the place of reassembly is not the place of manufacture.

"Predecessor" means an entity that is replaced by a successor and includes any predecessors of the predecessor.

"Reasonable inquiry" has the meaning provided in the clause 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment.

"Restricted business operations" means business operations in Sudan that include power production activities, mineral extraction activities, oil-related activities, or the production of military equipment, as those terms are defined in the Sudan Accountability and Divestment Act of 2007 (Pub. L. 110-174). Restricted business operations do not include business operations that the person (as that term is defined in Section 2 of the Sudan Accountability and Divestment Act of 2007) conducting the business can demonstrate--

(1) Are conducted under contract directly and exclusively with the regional government of southern Sudan;

(2) Are conducted pursuant to specific authorization from the Office of Foreign Assets Control in the Department of the Treasury, or are expressly exempted under Federal law from the requirement to be conducted under such authorization;

(3) Consist of providing goods or services to marginalized populations of Sudan;

(4) Consist of providing goods or services to an internationally recognized peacekeeping force or humanitarian organization;

(5) Consist of providing goods or services that are used only to promote health or education; or

(6) Have been voluntarily suspended.

"Sensitive technology"--

(1) Means hardware, software, telecommunications equipment, or any other technology that is to be used specifically--

(i) To restrict the free flow of unbiased information in Iran; or

(ii) To disrupt, monitor, or otherwise restrict speech of the people of Iran; and

(2) Does not include information or informational materials the export of which the President does not have the authority to regulate or prohibit pursuant to section 203(b)(3) of the International Emergency Economic Powers Act (50 U.S.C. 1702(b)(3)).

"Service-disabled veteran-owned small business concern"--

(1) Means a small business concern--

(i) Not less than 51 percent of which is owned by one or more service-disabled veterans or, in the case of any publicly owned business, not less than 51 percent of the stock of which is owned by one or more service-disabled veterans; and

(ii) The management and daily business operations of which are controlled by one or more service-disabled veterans or, in the case of a service-disabled veteran with permanent and severe disability, the spouse or permanent caregiver of such veteran.

(2) Service-disabled veteran means a veteran, as defined in 38 U.S.C. 101(2), with a disability that is service-connected, as defined in 38 U.S.C. 101(16).

"Small business concern"--

(1) Means a concern, including its affiliates, that is independently owned and operated, not dominant in its field of operation, and qualified as a small business under the criteria in 13 CFR part 121 and size standards in this solicitation.

(2) Affiliates, as used in this definition, means business concerns, one of whom directly or indirectly controls or has the power to control the others, or a third party or parties control or have the power to control the others. In determining whether affiliation exists, consideration is given to all appropriate factors including common ownership, common management, and contractual relationships. SBA determines affiliation based on the factors set forth at 13 CFR 121.103.

"Small disadvantaged business concern, consistent with 13 CFR 124.1002", means a small business concern under the size standard applicable to the acquisition, that--

(1) Is at least 51 percent unconditionally and directly owned (as defined at 13 CFR 124.105) by--

(i) One or more socially disadvantaged (as defined at 13 CFR 124.103) and economically disadvantaged (as defined at 13 CFR 124.104) individuals who are citizens of the United States; and

(ii) Each individual claiming economic disadvantage has a net worth not exceeding $750,000 after taking into account the applicable exclusions set forth at 13 CFR 124.104(c)(2); and

(2) The management and daily business operations of which are controlled (as defined at 13 CFR 124.106) by individuals, who meet the criteria in paragraphs (1)(i) and (ii) of this definition.

"Subsidiary" means an entity in which more than 50 percent of the entity is owned--

(1) Directly by a parent corporation; or

(2) Through another subsidiary of a parent corporation.

"Successor" means an entity that has replaced a predecessor by acquiring the assets and carrying out the affairs of the predecessor under a new name (often through acquisition or merger). The term "successor" does not include new offices/divisions of the same company or a company that only changes its name. The extent of the responsibility of the successor for the liabilities of the predecessor may vary, depending on State law and specific circumstances.

"Veteran-owned small business concern" means a small business concern--

(1) Not less than 51 percent of which is owned by one or more veterans (as defined at 38 U.S.C. 101(2)) or, in the case of any publicly owned business, not less than 51 percent of the stock of which is owned by one or more veterans; and

(2) The management and daily business operations of which are controlled by one or more veterans.

"Women-owned business concern" means a concern which is at least 51 percent owned by one or more women; or in the case of any publicly owned business, at least 51 percent of its stock is owned by one or more women; and whose management and daily business operations are controlled by one or more women.

"Women-owned small business concern" means a small business concern--

(1) That is at least 51 percent owned by one or more women; or, in the case of any publicly owned business, at least 51 percent of the stock of which is owned by one or more women; and

(2) Whose management and daily business operations are controlled by one or more women.

"Women-owned small business (WOSB) concern eligible under the WOSB Program" (in accordance with 13 CFR part 127), means a small business concern that is at least 51 percent directly and unconditionally owned by, and the management and daily business operations of which are controlled by, one or more women who are citizens of the United States, and the concern is certified by SBA or an approved third-party certifier in accordance with 13 CFR 127.300.

(b) (1) Annual Representations and Certifications. Any changes provided by the Offeror in paragraph (b)(2) of this provision do not automatically change the representations and certifications in SAM.

(2) The offeror has completed the annual representations and certifications electronically in SAM accessed through http://www.sam.gov. After reviewing SAM information, the Offeror verifies by submission of this offer that the representations and certifications currently posted electronically at FAR 52.212-3, Offeror Representations and Certifications--Commercial Products and Commercial Services, have been entered or updated in the last 12 months, are current, accurate, complete, and applicable to this solicitation (including the business size standard(s) applicable to the NAICS code(s) referenced for this solicitation), at the time this offer is submitted and are incorporated in this offer by reference (see FAR 4.1201), except for paragraphs ___

[Offeror to identify the applicable paragraphs at (c) through (v) of this provision that the offeror has completed for the purposes of this solicitation only, if any.

These amended representation(s) and/or certification(s) are also incorporated in this offer and are current, accurate, and complete as of the date of this offer.

Any changes provided by the offeror are applicable to this solicitation only, and do not result in an update to the representations and certifications posted electronically on SAM.]

(c) Offerors must complete the following representations when the resulting contract is for supplies to be delivered or services to be performed in the United States or its outlying areas, or when the contracting officer has applied part 19 in accordance with 19.000(b)(1)(ii). Check all that apply.

(1) Small business concern. The offeror represents as part of its offer that--

(i) It [ ___ ] is, [ ___ ] is not a small business concern; or

(ii) It [ ___ ] is, [ ___ ] is not a small business joint venture that complies with the requirements of 13 CFR 121.103(h) and 13 CFR 125.8(a) and (b). [The offeror shall enter the name and unique entity identifier of each party to the joint venture: ___ ]

(2) Veteran-owned small business concern. (Complete only if the offeror represented itself as a small business concern in paragraph (c)(1) of this provision.) The offeror represents as part of its offer that it [ ___ ] is, [ ___ ] is not a veteran-owned small business concern.

http://www.sam.gov/

(3) Service-disabled veteran-owned small business concern. [Complete only if the offeror represented itself as a veteran-owned small business concern in paragraph (c)(2) of this provision.] The offeror represents as part of its offer that--

(i) It [ ___ ] is, [ ___ ] is not a service-disabled veteran-owned small business concern; or

(ii) It [ ___ ] is, [ ___ ] is not a joint venture that complies with the requirements of 13 CFR 125.18(b)(1) and (2).

[The offeror shall enter the name and unique entity identifier of each party to the joint venture: ___ .] Each service-disabled veteran-owned small business concern participating in the joint venture shall provide representation of its service-disabled veteran-owned small business concern status.

(4) Small disadvantaged business concern. (Complete only if the offeror represented itself as a small business concern in paragraph (c)(1) of this provision.) The offeror represents that it [ ___ ] is, [ ___ ] is not a small disadvantaged business concern as defined in 13 CFR 124.1002.

(5) Women-owned small business concern. (Complete only if the offeror represented itself as a small business concern in paragraph (c)(1) of this provision.) The offeror represents that it [ ___ ] is, [ ___ ] is not a women-owned small business concern.

(6) WOSB joint venture eligible under the WOSB Program. The offeror represents that it [ ___ ] is, [ ___ ] is not a joint venture that complies with the requirements of 13 CFR 127.506(a) through (c). [The offeror shall enter the name and unique entity identifier of each party to the joint venture: ___ .

(7) Economically disadvantaged women-owned small business…