FN1398-14_AMEND_2.docx

AMENDMENT OF SOLICITATION/ MODIFICATION OF CONTRACT

1. CONTRACT ID CODE

PAGE OF PAGES

2. AMENDMENT/MODIFICATION NO.

3. EFFECTIVE DATE

4. REQUISITION/PURCHASE REQ. NO.

5. PROJECT NO. (If applicable)

6. ISSUED BY

CODE

7. ADMINISTERED BY (If other than Item 6)

See Block 6

8. NAME AND ADDRESS OF CONTRACTOR (No., street, country, State and Zip Code)

(x)

9A. AMENDMENT OF SOLICITATION NO.

FN1398-14

X

9B. DATED (SEE ITEM 11)

04/17/2014

10A. MODIFICATION OF CONTRACT/ORDER NO.

10B. DATED (SEE ITEM 13)

FACILITY CODE

11. THIS ITEM ONLY APPLIES TO AMENDMENT OF SOLICITATIONS

The above numbered solicitation is amended as set forth in Item 14. The hour and the date specified for receipt of Offers is extended, is not extended.

Offers must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended, by one of the following methods: (a) By completing items 8 and 15, and returning copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted; or (c) By separate letter or telegram which includes a reference to the solicitation and amendment number. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE

DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. ACCOUNTING AND APPROPRIATION DATA (If required)

13. THIS ITEM APPLIES ONLY TO MODIFICATIONS OF CONTRACTS/ORDERS,

IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

(X)

A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE CONTRACT ORDER NO. IN ITEM 10A.

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, Appropriation date, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103 (b).

C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF :

D. OTHER (Specify type of modification and authority)

E. IMPORTANT : Contractor is not, x is required to sign this document and return 2 copies to the issuing office.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

COMMODITY: Wood Working Machinery

SEE ATTACHED

Except as provided herein, all terms and conditions of the document referenced in Item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A. NAME AND TITLE OF SIGNER (Type or print)

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)

Tiffani Balestrini, Contract Specialist

15B. CONTRACTOR/OFFEROR

15C. DATE SIGNED

16B. UNITED STATES OF AMERICA

16C. DATE SIGNED

BY

(Signature of the person authorized to sign)

(Signature of contracting officer)

NSN 7540-01-152-8070

PREVIOUS EDITION UNUSABLE

30-105

STANDARD FORM 30 (REV. 10-83)

Prescribed by GSA

FAR(48 CFR) 53.243

This amendment hereby makes the following changes to specification for the CNC Machine Center as well as to closing date of the solicitation document.

The statement of work (machine specifications) for the CNC Machine Center is hereby changed from:

Statement of Work for CNC Router System:

Statement of Work for CNC Router System:

Minimum Requirements for CNC Router System:

Description:

X-Axis Travel = 48.0" Y-Axis Travel = 48.0" Z-Axis Travel = 9" Gantry Clearance = 7-1/2" Distance Between Uprights = 57" Foot Print: W=78", L=71", H=60"

Specifications:

Control System: Micro stepper controller with brushless motors and hand held controlpendant Compatibility: G&M code Drive System: Precision rack-n-pinion on X/Y, ball screw on Z-axis Repeatability: =/-.003 inches Max rapid traverse speed: 800 in/min Approx. Weight = 2000 lbs

(7) 1.0HP spindles spaced on 6" center spacing Spindles will be mounted on a T slot for easy adjustment, allowing operator to move if desired.

NOTE: Actual spindle motion in the X-Axis will be 12" Vacuum Table: 1.0" phenolic vacuum/T-slot table (4) independent zones T-slot center distance=310mm (12.205")

System Power Requirements:

7.5 HP pump requires a dedicated 230V, 3-ph 30 amp circuit

Machine controls and spindle require 230V, 3-ph 20 amp circuit

FOB Destination and FOB Origin pricing must be provided for this machine.

Machine must be shipped and packaged in accordance with industry standards.

Training:

Vendor must provide 1 day on site setup and training. Pricing for this training will be scheduled after award, and shall be included as a separate line item in the proposal. Successful offeror will be required to supply information of individual to conduct training for background clearance prior to being admitted into UNICOR which is located in a Federal Correctional Facility. UNICOR reserves the right to deny access to any individual based on background clearance results. Pricing for training and travel must be provided as a separate line item in the proposal. No additional fees will be paid.

The specification is hereby changed to the following specification:

Statement of Work for CNC Router System:

Minimum Requirements for CNC Router System:

Description:

X-Axis Travel = 48.0" Y-Axis Travel = 48.0" Z-Axis Travel = 9" Gantry Clearance = 7-1/2" Distance Between Uprights = 57" Foot Print: W=78", L=71", H=60"

Specifications:

Control System: Micro stepper controller with brushless motors and hand held control pendant Compatibility: G&M code Drive System: Precision rack-n-pinion on X/Y, ball screw on Z-axis Repeatability: =/-.003 inches Max rapid traverse speed: 800 in/min Approx. Weight = 2000 lbs

(7) 1.0HP spindles spaced on 6" center spacing Spindles will be mounted on a T slot for easy adjustment, allowing operator to move if desired.

NOTE: Actual spindle motion in the X-Axis will be 12" Vacuum Table: 1.0" phenolic vacuum/T-slot table (4) independent zones T-slot center distance=310mm (12.205")

System Power Requirements:

Machine controls and spindle require 230V, 3-ph 20 amp circuit

FOB Destination and FOB Origin pricing must be provided for this machine.

Machine must be shipped and packaged in accordance with industry standards.

Training:

Vendor must provide 1 day on site setup and training. Pricing for this training will be scheduled after award, and shall be included as a separate line item in the proposal. Successful offeror will be required to supply information of individual to conduct training for background clearance prior to being admitted into UNICOR which is located in a Federal Correctional Facility. UNICOR reserves the right to deny access to any individual based on background clearance results. Pricing for training and travel must be provided as a separate line item in the proposal. No additional fees will be paid.

The closing date of this solicitation is hereby changed from Tuesday July 22, 2014 @ 2:00 pm EST to Tuesday August 5, 2014 @ 2:00 pm EST

Except as provided herein all other terms and conditions remain unchanged.