Engineering_Data_Requirements.doc

REV:

ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

XXXXXXXXXXXXXXXX

2. PART NUMBER:

3. NATIONAL STOCK NUMBER:

1234-12-123-1234FG

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC, WILL BE USED IN LIEU OF THE DATA INDICATED. THE SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

DOOR, ACCESS, AIRCRAFT

2. PART NUMBER:

160D115009-31

3. NATIONAL STOCK NUMBER:

1560-01-487-1831 FJ

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC. WILL BE USED IN LIEU OF THE DATA INDICATED. THE SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.

5. THE CONTRACTOR IS RESPONSIBLE TO COMPLETELY RESEARCH THESE MANUALS, SPECIFICATIONS, AND STANDARDS AND FULLY UNDERSTAND THE REQUIREMENTS NECESSARY FOR THE MANUFACTURE OF COMPONENT PARTS AND ASSEMBLIES. ALL DEVIATIONS, MINOR AND MAJOR, FROM THE ENGINEERING DRAWING PACKAGE SHALL BE SUBMITTED TO OO-ALC EN.

6. WHEN MILITARY DOCUMENTS LISTED IN THE ENGINEERING DRAWING ARE CANCELLED THEY SHALL BE REPLACED BY THE INDUSTRY EQUIVALENT DOCUMENT SPECIFIED ON THE MILITARY DOCUMENT’S CANCELLATION NOTICE. THIS APPLIES TO THE ORIGINAL AIRCRAFT MANUFACTURER’S SPECIFICATIONS THAT ARE CITED IN THE DRAWING, AS WELL. THE CHARACTERISTICS OF TYPE, GRADE, CLASS, ETC. SPECIFIED IN THE CANCELLED MILITARY DOCUMENT SHALL BE MAINTAINED OR EXCEED THOSE CHARACTERISTICS WHEN APPLYING THE INDUSTRY EQUIVALENT DOCUMENT(S). WHEN THERE IS NO LISTED REPLACEMENT THE CONTRACTOR SHALL REQUEST AND RECOMMEND A SUBSTITUTE DOCUMENT FROM OO-ALC EN THROUGH THE GOVERNMENT CONTRACTING OFFICIAL DEPENDING ON THE APPLICABLE SYSTEM.

7. USE OF NORTHROP GRUMMAN SPECIFICATION Z-R701 IN CONJUNCTION WITH MIL-STD-130 IS MANDATORY TO ENSURE THE PROPER MARKING OF THE PARTS. (Z-R701 HAS UNLIMITED DATA RIGHTS IN JEDMICS)

8. "IUID" (ITEM UNIQUE IDENTIFIER) IS REQUIRED IAW MIL-STD-130. SPECIFIC INSTRUCTIONS FOR MARKING METHODS, LOCATION, CONTENT AND FORMAT SHALL BE SPECIFIED BY THE CONTRACTOR AND SUBMITTED TO THE GOVERNMENT FOR APPROVAL PRIOR TO CONTRACT DELIVERY. THE CONTRACTOR MUST DEMONSTRATE THE MARKING DOES NOT ADVERSELY AFFECT ITEM INTEGRITY OR PERFORMANCE AND WILL REMAIN READABLE AND ATTACHED THROUGHOUT THE USEABLE LIFE OF THE ITEM. IUID IS REQUIRED FOR ITEMS WHERE THE INDIVIDUAL COST PER UNIT IS GREATER THAN $5,000 OR IF THE ITEM HAS BEEN IDENTIFED AS FATIGUE CRITICAL REGARDLESS OF THE ITEMS PER UNIT COST. IUID WILL BE ACCOMPLISHED THROUGH A TECHNICAL INFORMATION EXCHANGE WITH COGNIZANT ENGINEER AND SUCCESSFUL BIDDER.

9. THE FOLLOWING TOOLING IS IDENTIFIED FOR MANUFACTURE OF THIS PART:

160D115009-23ASF

LOCATION: 04A047A002F

160D115009-23MAS

LOCATION: 26A008B002F

10. THE ABOVE TOOLING IS LISTED AS AVAILABLE AT AMARC, DAVIS MONTHAN AFB. THIS TOOLING IS NOT REQUIRED BY THE GOVERNMENT FOR MANUFACTURING OF THIS PART. THE CONDITION OF THE TOOLING IS UNKNOWN. THE CONTRACTOR MAY USE THIS TOOLING AT THEIR OWN DISCRETION AND USEAGE WILL BE IN “AS IS CONDITION”. THE SHIPPING WILL BE AT CONTRACTOR’S EXPENSE. THE CONTRACTOR MAY DEVELOP/MANUFACTURE THEIR OWN TOOLING REQUIRED TO PRODUCE THIS PART. PRIOR TO TOOL DEVELOPEMENT, THE CONTRACTOR SHALL ADVISE THE GOVERNMENT IN WRITING OF THEIR INTENT TO DEVELOP NEW TOOLING. THE CONTRACTOR SHALL NOT PROCEED TO DEVELOP NEW TOOLING WITHOUT THE EXPRESS CONSENT OF THE GOVERNMENT PROCURING AGENCY.

11. EO 11A0661-H needs to be incorporated during manufacturing. Essentially the -67 inner skin should include a tab that covers the -157 or -57 block. This detail was omitted from the original drawing and is corrected by said EO.

PREPARED BY:

RICHARD TILTON

OFFICE SYMBOL:

GBMAF

DATE:

20080411

PREPARED BY:

GREG BRODERICK

OFFICE SYMBOL:

416 SCMS/GUMB

DATE:

4/11/2011

HILL AFB FORM 462 Page 1 of 1