FXSB_18-1461_SOW_R1.pdf

673d Civil Engineer Squadron Joint Base Elmendorf-Richardson, Alaska

12 July 2018

STATEMENT OF WORK

Repair Install Flight Line Security Camera, Multiple Buildings

FXSB 18–1461 Building 17660 FXSB 18-1643 Building 9696

FXSB 18-1464 Building 16670 FXSB 18-1465 Building 10682 FXSB 18-1466 Building 9684

FXSB 18-1471 Building 12755

SECTION 1: PROJECT INFORMATION

1.1 PROJECT LOCATION: The project shall be completed at building 9684, 9696, 10682, 12755, 16670 and 17660 on JBER- Elmendorf, Alaska. See drawing E1.0 Project Location Map for building locations. Project hours are standard work hours 08:00-17:00.

1.2 UNIQUE REQUIREMENTs:

i. Site Access: This project is located in a controlled access area. Individuals entering this site shall be subject to inspection upon entering and leaving the site. Project scheduling and coordination of site access is required.

ii. Building access shall be coordinated/approved at least 7 days in advance. Building access can be terminated/postponed/rescheduled at any time if mission impact identified by communications squadron personnel or JBER Mission partners.

1.3 PROJECT DESCRIPTION: Provide labor and materials to install Electronic Security Equipment (ESE) in building 9684, 9696, 10682, 12755, 16670 and 17660.

1.4 PROJECT DURATION: Contract performance period is 365 days from NTP.

1.5 PRICE SCHEDULE: Shall be submitted in accordance with the attached Price Schedule for specific requirements.

SECTION 2: GENERAL REQUIREMENTS

2.1 WORKMANSHIP: All work shall be accomplished in accordance with all applicable Federal, National and local codes and publications. Contractor shall field verify all measurements, quantities, or value stated by the Government. Liquidated damages shall be assessed if the project is not completed within the scheduled performance period.

2.2 WORKSITE: The contractor shall limit the work to the areas indicated by the government. The contractor shall make every effort not to disturb or obstruct parts of the facilities still occupied by the government. The contractor shall make efforts to minimize interference to Government operations. The contractor shall coordinate and schedule work with the 673 CES/CENM office prior the start of construction. The contractor shall dispose of all construction debris off base at an ADEC permitted disposal facility.

2.3 SITE SECURITY AND PROTECTION: The contractor shall make every effort to secure the work site, allowing only authorized personnel to enter the work site. The contractor shall protect the site from damage from weather, vandalism, and/or theft.

2.4 DAMAGE TO EXISTING SITE CONDITIONS: The contractor shall be responsible to repair any and all damage incurred to existing Real Property/Grounds due to poor workmanship at no cost to the government. Contractor shall not park or drive on sidewalk or grassy/snowy areas. Damage incurred shall be repaired at no cost to the government.

2.5 HEALTH/SAFETY: The contractor shall be responsible for compliance with OSHA, EM 385-1-1, and AFOSH standards. The contractor shall maintain a clean and debris free site at all times.

The contractor shall keep driveways and entrances into and around the work site clear at all times. The contractor shall not use driveways or entrances as employee parking or storage of materials unless otherwise stated. The contractor shall minimize storage of materials and equipment on site. The contractor shall comply with the installations’ Foreign Object Debris (FOD) program requirements.

2.6 GREEN PROCURMENT: Contractor must incorporate “green procurement” principles into the design of their projects. Specifically, consult the EPA’s web site at www.epa.gov/cpg/products.htm for a listing of the products that have been mandated as green procurement requirements for purchases.

SECTION 3: TECHNICAL CRITERIA

3.1 Technical requirements

a. Camera System in building 9684, 9696, 10682, 16670, 17660: Shall be in accordance with the attached drawings. Camera system shall consist of exterior wall mounted dome type PTZ cameras equipped with wall brackets, corner adapters, environmental housing, and heaters suitable for Alaska cold weather environment.

b. Recording server in building 12755: Shall be provided in accordance with the attached drawings.

c. Intrusion Detection System: Provide intrusion detection equipment and necessary wiring in accordance with the attached drawings

d. VICADS licensing shall be provided for all cameras and recording server.

e. Provide additional 7 camera VICADS licenses for existing cameras in building 8681

(1 license), building 9684 (1 license), building 9696 (1 license), building 16716 (3 licenses).

f. IP Service licensing shall be provided for all Cisco switches

g. It is contractor’s responsibility to integrate the newly installed equipment into existing JBER Basewide system. The existing Electronic Security Equipment in JBER http://www.epa.gov/cpg/products.htm is Honeywell Vindicator for instruction detection and PSSGI Video Image Control and Display System (VICADS) for video recording and viewing.

h. The only equipment listed in “Non-Nuclear IDS Equipment Approval” memorandum dated 13 December 2017 (attached)” shall be authorized in the project, and shall be compatible with existing JBER Electronic Security Equipment system.

3.2 Field Tests: Contractor shall demonstrate that system is 100% functional before field tests can be scheduled.

1. ESE system Testing: Shall be in accordance with ESE-TP-0023 (attached), and shall be conducted by contractor and witnessed by 673 CEG Alarm Managers and SFS personnel. A written notification of the test date and time shall be sent to 673 CES Construction Manager at least 7 days before the scheduled test date. System Test Procedure shall be submitted for approval 30 days after NTP.

2. Horizontal Cable tests. Perform testing for each outlet as follows:

a) Perform Category 6A link tests in accordance with TIA-568-C.1 and TIA-568-C.2. Tests shall include wire map, length, insertion loss, NEXT, PSNEXT, ELFEXT, PSELFEXT, return loss, propagation delay, and delay skew.

b) Optical fiber Links. Perform optical fiber end-to-end link tests in accordance with TIA-

568.3-D.

SECTION 4: DRAWINGS

a. E1.0 Project Location Map

b. E2.0 General Requirements

c. E2.1 Building 17660

d. E2.1A Building 17660 – Details

e. E2.3 Building 9696

f. E2.4 Building 16670

g. E2.4A Building 16670 – Details

h. E2.5 Building 10682

i. E2.5A Building 10682 – Details

j. E2.6 Building 9684

k. E2.6A Building 9684 – Details

l. E2.10 Building 12755

SECTION 5: PROJECT MANAGER

James Nguyen. PE, RCCD Electrical Engineer James.Nguyen.3@us.af.mil Phone: 907-384-7773 mailto:James.Nguyen.3@us.af.mil

A

B

C

D

E

F

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

N o

D A

T E

D E

S C

R I P

T I O

N B

Y

P R

O J E

C T

M

N

A G

E R

D E

S I G

N E

D

B

Y

D

S

H O

W N

F X

X

X

SHEET OF

SHEET REFERENCE

R E

V I S

I O

N S

T R

A C

E D

Y

A N

S I

P L O

T

S

C A

L E

I N

V O

I C

E

N

U M

B E

R

R E

P A

I R

N

S T

A L

L

F

L I G

L

N

E

E1.0

S E

C U

R I T

Y

C

A M

E R

A

M

U L

T I P

U I L

D I N

G S

P R

O J

E C

T

L

O C

A T

I O

N

M

A P

J B

E R

E

L M

E N

D O

R F

A

L A

S K

A

D R

A W

I N

G

S

C A

L E

D A

T E

A

F

P

R O

J E

M

B E

R

F

O N

T R

A C

T

N

U M

B E

R

A E

C

F

I

M

E

X d g n

C H

I E

F r d

C

E S

C

E P

M E

A

R

C

D

E

F

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

N o

D

A T

E D

E S

C R

I P

T I O

N B

Y

P R

O J E

N

A G

E R

D E

S I G

N E

D

B

Y

D

O

W N

F X

X

X

SHEET OF

SHEET REFERENCE

R E

V I S

I O

N S

T R

A C

A N

S I

P L

A

L E

I N

V O

I C

E

N

U M

B E

R

R E

P A

S T

A L

L

F

L I G

N

E

E-2.0

S E

C U

R I T

Y

C

A M

E R

A

M

U L

T I P

I L

D I N

G S

G E

N E

R A

L

R

E Q

U I R

E M

E N

T S

J B

E R

E

L M

E N

D O

R F

A

L A

S K

A

D R

A W

I N

G

S

C A

L E

D A

T E

A

F

P

R O

J E

M

B E

R

N

T R

A C

T

N

U M

B E

R

A E

C

F

I L

E

N

A M

E

X d g n

C H

I E

F r d

S

C

E P

M E

A

R

C

D

E

F

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

N o

D

A T

E D

E S

C R

I P

T I O

N B

Y

P R

O J E

N

A G

E R

D E

S I G

N E

D

B

Y

D

O

W N

F

X S

B

SHEET OF

SHEET REFERENCE

R E

V I S

I O

N S

T R

A C

A N

S I

P L

A

L E

I N

V O

I C

E

N

U M

B E

R

R E

P A

S T

A L

L

F

L I G

N

E

E-2.1

S E

C U

R I T

Y

C

A M

E R

A

M

U L

T I P

I L

D I N

G S

B

U I L

D I N

G

J B

E R

E

L M

E N

D O

R F

A

L A

S K

A

D R

A W

I N

G

S

C A

L E

D A

T E

A

F

P

R O

J E

M

B E

R

N

T R

A C

T

N

U M

B E

R

A E

C

F

I L

E

N

A M

E

X d g n

C H

I E

F

S

C

E P

M E

A

R

C

D

E

F

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

N o

D

A T

E D

E S

C R

I P

T I O

N B

Y

P R

O J E

N

A G

E R

D E

S I G

N E

D

B

Y

D

O

W N

F

X S

B

SHEET OF

SHEET REFERENCE

R E

V I S

I O

N S

T R

A C

A N

S I

P L

A

L E

I N

V O

I C

E

N

U M

B E

R

R E

P A

S T

A L

L

F

L I G

N

E

E-2.1A

S E

C U

R I T

Y

C

A M

E R

A

M

U L

T I P

I L

D I N

G S

B

U I L

D I N

G

J B

E R

E

L M

E N

D O

R F

A

L A

S K

A

D R

A W

I N

G

S

C A

L E

D A

T E

A

F

P

R O

J E

M

B E

R

N

T R

A C

T

N

U M

B E

R

A E

C

F

I L

E

N

A M

E

X d g n

C H

I E

F

S

C

E P

M E

A

R

A

B

C

D

E

F

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

N o

D

A T

E D

E S

C R

I P

T I O

N B

Y

P R

O J E

N

A G

E R

D E

S I G

N E

D

B

Y

D

O

W N

F X

SHEET OF

SHEET REFERENCE

R E

V I S

I O

N S

T R

A C

A N

S I

P L

A

L E

I N

V O

I C

E

N

U M

B E

R

R E

P A

S T

A L

L

F

L I G

N

E

S E

C U

R I T

Y

C

A M

E R

A

P

R O

J E

C T

M

U L

T I P

I L

D I N

S

E-2.3

B U

I L

D I N

G

J B

E R

E

L M

E N

D O

R F

A

L A

S K

A

D R

A W

I N

G

S

C A

L E

D A

T E

A

F

P

R O

J E

M

B E

R

N

T R

A C

T

N

U M

B E

R

A E

C

F

I L

E

N

A M

E

X d g n

C H

I E

F

S

C

E P

M E

A

R

C

D

E

F

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

N o

D

A T

E D

E S

C R

I P

T I O

N B

Y

P R

O J E

N

A G

E R

D E

S I G

N E

D

B

Y

D

O

W N

F X

SHEET OF

SHEET REFERENCE

R E

V I S

I O

N S

T R

A C

A N

S I

P L

A

L E

I N

V O

I C

E

N

U M

B E

R

R E

P A

S T

A L

L

F

L I G

N

E

E-2.4

S E

C U

R I T

Y

C

A M

E R

A

M

U L

T I P

I L

D I N

G S

B

U I L

D I N

G

J B

E R

E

L M

E N

D O

R F

A

L A

S K

A

D R

A W

I N

G

S

C A

L E

D A

T E

A

F

P

R O

J E

M

B E

R

N

T R

A C

T

N

U M

B E

R

A E

C

F

I L

E

N

A M

E

X d g n

C H

I E

F

S

C

E P

M E

A

R

C

D

E

F

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

N o

D

A T

E D

E S

C R

I P

T I O

N B

Y

P R

O J E

N

A G

E R

D E

S I G

N E

D

B

Y

D

O

W N

F X

SHEET OF

SHEET REFERENCE

R E

V I S

I O

N S

T R

A C

A N

S I

P L

A

L E

I N

V O

I C

E

N

U M

B E

R

R E

P A

S T

A L

L

F

L I G

N

E

E-2.4A

S E

C U

R I T

Y

C

A M

E R

A

M

U L

T I P

I L

D I N

G S

B

U I L

D I N

G

J B

E R

E

L M

E N

D O

R F

A

L A

S K

A

D R

A W

I N

G

S

C A

L E

D A

T E

A

F

P

R O

J E

M

B E

R

N

T R

A C

T

N

U M

B E

R

A E

C

F

I L

E

N

A M

E

X d g n

C H

I E

F

S

C

E P

M E

A

R

C

D

E

F

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

N o

D

A T

E D

E S

C R

I P

T I O

N B

Y

P R

O J E

N

A G

E R

D E

S I G

N E

D

B

Y

D

O

W N

F S

X

SHEET OF

SHEET REFERENCE

R E

V I S

I O

N S

T R

A C

A N

S I

P L

A

L E

I N

V O

I C

E

N

U M

B E

R

R E

P A

S T

A L

L

F

L I G

N

E

E-2.5

S E

C U

R I T

Y

C

A M

E R

A

M

U L

T I P

I L

D I N

G S

B U

I L

D I N

G

J B

E R

E

L M

E N

D O

R F

A

L A

S K

A

D R

A W

I N

G

S

C A

L E

D A

T E

A

F

P

R O

J E

M

B E

R

N

T R

A C

T

N

U M

B E

R

A E

C

F

I L

E

N

A M

E

X d g n

C H

I E

F

S

C

E P

M E

A

R

C

D

E

F

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

N o

D

A T

E D

E S

C R

I P

T I O

N B

Y

P R

O J E

N

A G

E R

D E

S I G

N E

D

B

Y

D

O

W N

F S

X

SHEET OF

SHEET REFERENCE

R E

V I S

I O

N S

T R

A C

A N

S I

P L

A

L E

I N

V O

I C

E

N

U M

B E

R

R E

P A

S T

A L

L

F

L I G

N

E

E-2.5A

S E

C U

R I T

Y

C

A M

E R

A

M

U L

T I P

I L

D I N

G S

B U

I L

D I N

G

J B

E R

E

L M

E N

D O

R F

A

L A

S K

A

D R

A W

I N

G

S

C A

L E

D A

T E

A

F

P

R O

J E

M

B E

R

N

T R

A C

T

N

U M

B E

R

A E

C

F

I L

E

N

A M

E

X d g n

C H

I E

F

S

C

E P

M E

A

R

C

D

E

F

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

N o

D

A T

E D

E S

C R

I P

T I O

N B

Y

P R

O J E

N

A G

E R

D E

S I G

N E

D

B

Y

D

O

W N

F X

SHEET OF

SHEET REFERENCE

R E

V I S

I O

N S

T R

A C

A N

S I

P L

A

L E

I N

V O

I C

E

N

U M

B E

R

R E

P A

S T

A L

L

F

L I G

N

E

E-2.6

S E

C U

R I T

Y

C

A M

E R

A

M

U L

T I P

I L

D I N

G S

B U

I L

D I N

G

J B

E R

E

L M

E N

D O

R F

A

L A

S K

A

D R

A W

I N

G

S

C A

L E

D A

T E

A

F

P

R O

J E

M

B E

R

N

T R

A C

T

N

U M

B E

R

A E

C

F

I L

E

N

A M

E

X d g n

C H

I E

F

S

C

E P

M E

A

R

C

D

E

F

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

N o

D

A T

E D

E S

C R

I P

T I O

N B

Y

P R

O J E

N

A G

E R

D E

S I G

N E

D

B

Y

D

O

W N

F

X S

B

SHEET OF

SHEET REFERENCE

R E

V I S

I O

N S

T R

A C

A N

S I

P L

A

L E

I N

V O

I C

E

N

U M

B E

R

R E

P A

S T

A L

L

F

L I G

N

E

E-2.6A

S E

C U

R I T

Y

C

A M

E R

A

M

U L

T I P

I L

D I N

G S

B U

I L

D I N

G

J B

E R

E

L M

E N

D O

R F

A

L A

S K

A

D R

A W

I N

G

S

C A

L E

D A

T E

A

F

P

R O

J E

M

B E

R

N

T R

A C

T

N

U M

B E

R

A E

C

F

I L

E

N

A M

E

X d g n

C H

I E

F

S

C

E P

M E

A

R

C

D

E

F

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

N o

D

A T

E D

E S

C R

I P

T I O

N B

Y

P R

O J E

N

A G

E R

D E

S I G

N E

D

B

Y

D

O

W N

F X

SHEET OF

SHEET REFERENCE

R E

V I S

I O

N S

T R

A C

A N

S I

P L

A

L E

I N

V O

I C

E

N

U M

B E

R

R E

P A

S T

A L

L

F

L I G

N

E

E-2.10

S E

C U

R I T

Y

C

A M

E R

A

B

L D

G

B U

I L

D I N

G

J B

E R

E

L M

E N

D O

R F

A

L A

S K

A

D R

A W

I N

G

S

C A

L E

D A

T E

A

F

P

R O

J E

M

B E

R

N

T R

A C

T

N

U M

B E

R

A E

C

F

I L

E

N

A M

E

X d g n

C H

I E

F

S

C

E P

M E

A

R

DEPARTMENT OF THE AIR FORCE

AIR FORCE SECURITY FORCES CENTER

13 Jul 18

MEMORANDUM FOR SEE DISTRIBUTION

FROM: AFSFC/S2/5/6/8

SUBJECT: Non-Nuclear Intrusion Detection System (IDS) Equipment Approval

1. The IDS equipment listed below is approved for use when employed in the tested PL-1 Non- Nuclear through PL-4 applications and configurations. This letter consists of seven pages.

* Indicates correction, change, and/or addition.

+ Indicates item is no longer procurable and/or supported by OEM; however it is still approved for use as listed on this memorandum. Contact AFSFC/S5R at afsfc.ibdss@us.af.mil with any questions concerning these items.

PL-1 Non-Nuclear and Below

Command, Control Display Equipment (CCDE)

Will-Burt Annunciator

Will-Burt Annunciator Predator Elite, with integrated access control

Annunciator Version 3.2.274p, subpatch p32274.1.13.

LINXSNMP version 3.3.274P, subpatch 3.3.274P.1.13.30

* Annunciator Version 3.3.274p, subpatch p33274.1.13.33 + Annunciator Version 3.2.274p + Annunciator Version 3.0.252 + Annunciator Version 3.0.246 LINX Predator Enrollment System Version 4.1.220 LINX Predator Enrollment System Version 4.0.203 LINX Versatile Interface Panel (VIP) Version 1.172 LINX Versatile Interface Panel (VIP) Version 1.148 LINX Versatile Interface Panel (VIP) Version 1.64 LINX Versatile Interface Panel, Expandable (VIP-E) Version 7.284 LINX Versatile Interface Panel, Expandable (VIP-E) Version 7.145 + WSD 2000 Card Reader ver 1.8V WSD-E Card Reader ver 3.110

Advantor Annunciator

+ Advantor Advantage Suite for Networks (ASN) Version 4.0 Advantor Advantage Suite for Networks (ASN) Version 5.0 Advantor Advantage Suite for Networks (ASN) Version 6.2 (Win 10) Advantor Integrated Command, Control, and Access Control System Version 5.0 mailto:afsfc.ibdss@us.af.mil

Advantor Integrated Command, Control, and Access Control System Version 5.0 Service Pack 6 Advantor Integrated Command, Control, and Access Control System Version 6.0

Vindicator Annunciator

Vindicator Security Management and Reporting Terminal (SMART) Annunciator with Graphics Display:

+ Version 2.40 with Administrative Browser 4.0 + Version 2.43, Build 11 + Vindicator Command and Control (VCC) Version 1.0.1.5 + Vindicator Access Control System (ACS) Version 2.3, Build 21 + Transponder Firmware Version 2.28 + TS 4000 Radio Frequency (R/F) Modem Interface + Vindicator SMART with Graphics Display Version 2.39 and SAW Version 3.9 + Vindicator Command and Control Platform (VCCP) v5- Version 5.0 + Vindicator Command and Control Platform (VCCP) v5- Version 6.0 + Vindicator Command and Control Platform (VCCP) v5- Version 6.5 (Win 7, 32 bit only) + Vindicator Command & Control (VCC) GUI Version 5.1.1.4 + Vindicator Badge Manager 2 (VBM 2) Version 2.0.7.0 + Vindicator Badge Manager 2 (VBM 2) Version 2.0.7.1 (Win 7, 32 bit only) + Vindicator Security Archive Workstation (SAW 5) Version 5.1.0.6 + Honeywell Vindicator Site Commander Version 1.2.0.1 + V5 IDS Network Security Appliance – Intrusion Detection, Revision 3.2, Release 20:

UHS-8170

DES-8170T

AES-8170T

+ V5 ACS Network Security Appliance – Access Control Revision 3.2 Release 20:

UHS-1401

DES-1401T

AES-1407T

+ Vindicator UHS-Net Gateways:

UHS-8101 Version 2.33, Build 7 UHS-8102 Version 2.33, Build 6 UHS-8301 Version 2.33, Build 13 UHS-8400 Version 2.33, Build 13

+ Vindicator UHS-Net Transponder/Gateway Revision 3.3, Release 5:

UHS-1500

DES-1500T

AES-1500T

+ Vindicator UHS-Net Transponders Version 2.33, Build 13:

UHS-6842

UHS-6842F

DES-6842

DES-6842F

+ PC SMART PAC Software Package Version 5.1 + Proteus 5 & SmartSave 5 Software Programs Version 5.2

Vindicator Command and Control Platform (VCCP) Windows 7 (64-bit)

Vindicator Command & Control 2-Version 1.2.1.4 V5 ACS Network Security Application-Version 3.2, Release 23 UHS-1500 UHS-Net Field Panel-Version 3.3, Release 7 Security Archive Workstation 2-Version 1.4.2.9 Vindicator Badge Manager 3-Version 2.0.26.7 Vindicator Site Commander-Version 1.3.0.7 Vindicator Area Commander-Version 1.1.0.6 Vindicator Premise Controller-Version 3.3, Release 7 Vindicator PC SMART PAK-Version 6.0.0.1 Vindicator Security Server-Version 1.0

Assessment Subsystems

Video Servers

Advantor Video Management System (VMS) Software (For use only with Advantor ASN 6.0)

Advantor VMS Version #va-advantorvms-3.3.22-1 (1/el5) Advantor VMS Wall Version ds-vmx-3.3.1-3

Bosch Allegiant Matrix/Control System LTC 8600 and 8800

+ Broadware 4.80 / Cisco 5.1.1. Video Storage System (NOTE: Cisco renamed the 4.80 after purchasing Broadware.)

+ Video Image Control and Display System (VICADS) Version 4.0 Video Management System

+ Prometheus Security Group Global Inc. (PSSGI) (Formerly Open Roads Consulting, Inc.) Video Image Control and Display System (VICADS) Version 4.1 Video Management system using Vindicator V5, Version 6 as the annunciator

+ PSSGI Video Image Control and Display System (VICADS) Version 4.1 Service Pack

1.6 Video Management system using Vindicator V5, Version 6.5 as the annunciator

PSSGI Video Image Control and Display System (VICADS) Version 4.1 Service Pack

1.6 Video Management system using Lynx Predator Elite Version 3.2.274p, subpatch p32274.1.13 as the annunciator

* PSSGI Video Image Control and Display System (VICADS) Version 4.2.7 build

134 using Lynx Predator Elite Version 3.3.274p, subpatch p33274.1.13.33

* PSSGI Video Image Control and Display System (VICADS) Version 4.2.7 build 134 using Vindicator 7 as the annunciator

2.0 Video Management system using Vindicator VCCP Windows 7 as the annunciator. Note: DefendIR Thermal imager protocol support, RadarWall, and Geoserver are not approved for use.

2.4 Video Management system using Vindicator VCCP Windows 7 as the annunciator. Note: DefendIR Thermal imager protocol support, RadarWall, and Geoserver are not approved for use.

Assessment Cameras

Aventura CAM –IPE-2XW Internet Protocol (IP) Aventura CAM-IPM-8ZA-36X-IR (PTZ) + Bosch NWC-04-95-20P Internet Protocol (IP) Camera + Bosch NWC-04-95-20P (1/3 Format) + Bosch NBN-498-21P Internet Protocol (IP) Camera + Bosch Auto Dome VG 4-322-ECE1M + Bosch Auto Dome VG5-623-ECS + Bosch Auto Dome VG5-624-ECS + Bosch Auto Dome VG5-724-ECE2 Bosch Auto Dome 7000 Internet Protocol (IP) Camera with environmental housing + Bosch Dinion Internet Protocol (IP) 7000 Camera with environmental housing Bosch DINION Internet Protocol (IP) Starlight 7000 HD (NBN-73013-BA) Bosch NBN-63013-B Bosch NBN-63023-B Bosch NBN-71013-B Bosch NBN-71022-B + Burle 300H Camera + Burle TC 351 Camera (1/2 inch format) + Cohu 4865 Camera (WS3) (2/3 inch format) + Cohu 48x Camera (KUMMSC) (2/3 inch format) + Cohu 4915/4912-3000 Camera (1/2 inch format) Cohu 3930HD Indigo Vision 512147 (PTZ) Indigo Vision 11650-Audio-HD + IQ Eye 752 Internet Protocol (IP) Camera + Lumenera Le 165M-DN Internet Protocol (IP) Camera Lumenera Le 165ME-DN Internet Protocol (IP) Camera with environmental housing + Lumenera Le 165MP-DN Internet Protocol (IP) Camera with environmental housing + Pelco ES31CBW35-2N Pan Tilt Zoom (PTZ) System + Pelco ES30C/ES31C Pan Tilt Zoom (PTZ) System (1/4 inch format) with/ without optional Wiper Pelco ES4136-2N Esprit ES system Pan Tilt Zoom (PTZ) System (1/4 inch format) with/ without optional Wiper + Pelco MC3651H-2 Interior Camera (1/3 inch format) + Pelco IXE20 IP Camera Pelco ES4036-5W Esprit Series, with and without wiper, standard and pressurized + Pelco ES40E36-5W Esprit Series, with and without wiper, standard and pressurized Pelco ES40/41 Series Positioning System, Analog, PTZ, w/wo wiper Esprit SE Standard

& pressurized, model ES4036-5W

Pelco ES40E/41E Series Positioning System, IP, PTZ, w/wo wiper Esprit SE Standard & Pressurized, Model ES40E36-5W

Pelco IXE21 Internet Protocol (IP) Pelco P1220-ESR1 (PTZ)

VICON SN680D-B-WNIR(PTZ)

VICON IQ762WI-V6 Internet Protocol (IP) + Vivotek IP 7151 Vivotek SD8364E (PTZ) Vivotek IP816A-HP (interior only)

Interior Sensors

NOTE: Balanced Magnetic Switch (BMS) will not be used as a line of detection.

+ AN/GSS-20 Volumetric

+ AN/GSS-9(V) SA 1955 BMS

+ AN/GPS-15(V) Closed-Shelter Aircraft Sensor (C-SAS) (Volumetric) + AN/GSS-36(V) Open-Shelter Aircraft Sensor (O-SAS) (Volumetric) Banner Engineering Series Active Infrared (AIR), intrinsically safe, Model SMI30 (Must be installed as an array of individually reporting sensor points, for use across openings in areas where explosive fumes may be present)

+ Bosch DS 9370 PIR/MW (Volumetric) + Bosch DS 939 PIR (Volumetric) Dortronics 1110 x D x CT, Magnetic Lock/BMS Dortronics 1120 Series Electromagnetic Lock and BMS Eltec 862 Passive Infrared (PIR) Sensor (Wall) + General Electric (Sentrol) Model 2700 Series BMS General Electric (Sentrol) Model 2807T Explosion Proof Balanced Magnetic Switch

(BMS)

General Electric (Sentrol) Model 2507AH-L Wide Gap BMS General Electric (Sentrol) Model 2800 Series BMS + General Electric AP669 PIR (Volumetric) Magnasphere, High Security Sensor (HSS) Door Contact Switch, BMS, Version

HSSL2S000

Magnasphere L2C-101 (Concealed switch)/L2C 101A (Recessed Switch) Magnetic Contact Switch PL&E Communications AVT 234 (VMD) using Dinion analog infrared imagers, for interior applications only Securitron Group MSS-1 High Security Balanced Magnetic Switch East Coast Security Products Inc. ESM-6T Tandem Balanced Magnetic Switch Protech Passive Infrared and Microwave Intruder Detectors (PIRAMID) SDI-76-G (Volumetric) Protech Passive Infrared and Microwave Intruder Detectors (PIRAMID) SDI-77-D (Volumetric) Protech SDI-76M-HS1-H Volumetric (Coverage 60’x 40’, Two Sensors in Combination) Protech SDI-76MW Volumetric (Coverage 60’x 40’, Two Sensors in Combination) Protech SDI-77XL2-EX, Explosion Proof Volumetric Redscan RLS-3060SH Laser Scan Detector (Approved for wall and ceiling configurations) SightLogix SightSensor Video Motion Detection (VMD) using NS-90A Thermal Imager, for interior applications only.

United Technologies Interlogix AP669 Mirror Optic PIR (Volumetric) Visonic CH-1000 (Wall)

Visonic CH-1000/Xtalis ADPRO 18 WH PIR Combination (Ceiling) (Coverage 30’x 30’) Tyco Visonic Disc 360 Passive Infrared Sensor (Ceiling) (Coverage 360 Degree)

* Maxiris 3000/3100 Active IR Interior Sensor

+ AN/GSS-39(V) Interior Intrusion Detection System. Components include:

-- DR-301 -- DR-558 -- DR-851 -- HT-50B

-- HT-50DC -- HT-100B -- HT-100BC -- SDI-76A

-- SDI-77C -- SD-80B -- SD-80EHB -- SD-150B

-- SD-150EHB -- SRN-2000H

Exterior Sensors

The following sensors are approved for use as a standalone line of detection:

EAG of Americas Infrared Intrusion Detection System 4/2/2 (IIDS4/2/2) Active Infrared Sensor

EAG of Americas Infrared Intrusion Detection System 4/4/2/2/2 w/ PSTC EAG of Americas Intrusion Detection System 4/2 (IDS 4/2) Active Infrared Sensor IR Global Infrared Intrusion Detection System 4/4/2 (Note: Not approved for use in Northern tier, or areas where snow and ice accumulations are normal, pending further testing)

Microtrack buried line sensor (NOTE: Not approved for use in Northern tier, or areas where snow and ice accumulations are normal, pending further testing)

Senstar Omnitrax buried line sensor firmware version MSP v2.81 w/Field Programmable Gate Array (FPGA) v13.05 Senstar Omnitrax buried line sensor w/Firmware Version MSP v2.90 w/FPGA v13.93 + Perimitrax, Buried Cable Intrusion Detection Sensor Protect (PIRAMID) / SDI-76-XL-MIL, PIR and Monostatic Microwave Sensor Protech Sorhea Technology G-Fence 600 Zoning (600Z) System (Note: Not approved for use in Northern tier, or areas where snow and ice accumulations are normal, pending further testing)

* Protech Maxiris 3100 Active Infrared Barrier (100 meter) + Racon Single Stack; Barksdale Configuration - single stack, basket weave configuration with double stacked sensors at the corners + Racon Double Stack + Racon 16000-4 (Microwave) Sensor + Racon 14000-32 Microwave Sensor + Racon MPS-4100 (Microwave) + Racon MPS-14000-1 (Microwave) Senstar UltraWave Microwave Detection Sensor + Senstar Sentrax Short Ported Coaxial Cable Sensor (SPCS), large and small diameter cable, in the straight-line configuration + Birdeye Model IX Infrared Perimeter Detection System, up to 120m DeTekion Defensor 100 Fence Sensor

* Detekion Defensor 100 sensor system with the GD-5000 Eliminator signal analyzer DeTekion Vertical Taut Wire Sensor 400 (VTW-400), full fence or out-rigger configuration ECSI Infrared Pulsed Intrusion Detection System (IPIDS), up to 80m with spring loaded mount bases and 100m with solid concrete bases Fiber SenSys Fiber Defender FD200/300 series. The following models have been tested:

331, 332, 341, and 342. Note: The 331 and 332 series is with “Sensitive” Lead-in cables whereas the 341 and 342 series is with the “Insensitive” Lead-in cables.

Also, the last digit (1 or 2) indicates a single channel processor or dual channel processor. Additional note: The 33x series is normally utilized for TASS applications with the 34x series being utilized for all hardwired configurations.

+ Fence Protection System 2-2R (FPS-2-2R) FlexZone Fence Sensor (NOTE: Not approved for use in Northern tier, or areas where snow and ice accumulations are normal, pending further testing) G-Fence 600Z Fence Sensor

RBtec Ironclad Fence Sensor Double Run Configuration (Note: Not approved for use in Northern tier, or areas where snow and ice accumulations are normal, pending further testing) Southwest Microwave Intrepid Micropoint. (NOTE: Not approved for use in Northern tier, or areas where snow and ice accumulations are normal, pending further testing)

Southwest Microwave Intrepid Micropoint II.

Southwest (SW) Microwave 385 Monostatic Sensor, up to 100m SW Microwave 310 Bi-static Sensor, up to 100m Southwest Microwave 460B Active Infrared Exterior Sensor Southwest Microwave 330 Digital Microwave System Fiber Optics Intrusion Detection System (FO-IDS), Fiber Optic Sensor System (FOSS) Models 100 and 200 Fiber SenSys Fiber Defender 525 (Note: Not approved for use in Northern tier, or areas where snow and ice accumulations are normal, pending further testing)

The following sensors in combination are approved for use as a line of detection with fence climber enhancement detection:

+ Enhanced DTR-90 Vertical Taut Wire (VTW) Sensor, the DTR 90 “Y” VTW Sensor, or the VTW 400 Sensor installed at the top of the fence with any one of the following sensors installed on the fence:

Fiber SenSys Fiber Defender FD300 series. The following models have been tested:

331, 332, 341, and 342.

Fiber Optics Intrusion Detection System (FO-IDS), Fiber Optic Sensor System (FOSS) Models 100 and 200 + Fence Protection System 2 (FPS-2) + Fence Protection System 2-2R (FPS-2-2R)

Wide Area Detection/Approach Zone Sensors

+ PSRS STS-350 (FLIR/ICx) Ground Based Radar used as an approach sensor out to 125 meters (crawlers) as described below: ICX application software version

2.4.41.12 Firmware version 3.4.30 dated November 2, 2007.

+ PSRS STS-350 (FLIR/ICx) with control station application software version 2.4.41.12 or when integrated with Will Burt Annunciator Version 3.2.274p, subpatch p32274.1.13.

FLIR Ranger 1 Perimeter Surveillance Radar (approved with Advantor 6.2, Win 10 only)

* Magos SR-500 perimeter surveillance system when integrated with the Advantor Systems ASN, Version 6.2. MASS Version 2.24.100053, SR-500 Radar Version 3.64 and Radar Manager Version 1.5

PL-3 and Below

In addition to all of the above components, the following equipment is approved for use in the protection of PL-3 and below assets:

Command, Control Display Equipment (CCDE)

TASS 7.0 Annunciator (At deployed locations only) TASS 6.0.1.A Annunciator (At deployed locations only)

Assessment Subsystems

General Dynamics VZ-250 LRTI 23164-600 General Dynamics VZ-250 LRTI 23164Z1-600 (Improved Cooling) General Dynamics LRTI-w/CCTV

C907891 Complete Kit TICC/PTH only C907892

FLIR ThermoVision Multi-Sensor System (a.k.a. SLRTI) + T-2000 LRTI w/CCTV Complete Kit IBDSS1000-085 + T-2000 LRTI w/CCTV TICC/PTH only IBDSS1000-086 T-3000 LRTI w/CCTV Complete Kit FDTA-199 T-3000 LRTI w/CCTV TICC/PTH only

+ Surveillance Thermal Imager (WSTI) Sentry I and Sentry II

FLIR DEFENDIR MS-UC 640 30/90MM CZ

+ Short Range Thermal Imager; Fixed/Mounted (SRTI F/M) + DiOP Thermal Imager 180/60mm Thermal Upgrade Kit (TUK)

Interior Sensors: No Additional

Exterior Sensors: No Additional

Certified Air Force Test Sites:

Test Area C-3, Eglin AFB FL, and Cold Weather Test Site, Grand Forks AFB, ND are approved for conducting operational tests and evaluations on all IDS equipment.

2. A listing of equipment approved for use in PL-1 Nuclear applications is available in a separate letter maintained by the POC listed below.

3. This memorandum supersedes the 13 Apr 18 IDS approval memorandum. The POC is Mr.

Warren Greene, AFSFC/S5R, DSN 945-7072.

VENDITTI.ENRICO.W. Digitally signed by VENDITTI.ENRICO.W.JR.1055517041

JR.1055517041 Date: 2018.07.24 10:00:53 -05'00'

ENRICO W. VENDITTI, Colonel, USAF Director, Intel/Plans/Systems

DISTRIBUTION:

AFDW/A4S

HQ USAFE/A4S

HQ AFMC/A4S

HQ PACAF/A4S

HQ AETC/A4S

HQ AFSPC/A4S

HQ AFSOC/A4S

HQ AFRC/A4S

HQ AMC/A4S

HQ ACC/A4S

HQ AFGSC/A3S

NGB/A4S

HQ USAFA/SF

HQ USAF/A4SX

HQ USAF/A4SO

HQ AFLCMC/HBU

HQ AFLCMC/HNC (CCSD)

ESE-TP-0023

AF LIFE CYCLE MANAGEMENT CENTER

HANSCOM AIR FORCE BASE, MASSACHUSETTS

ELECTRONIC SECURITY EQUIPMENT (ESE)

MASTER INSTALLATION ACCEPTANCE TEST

AND TURNOVER PLAN

1 MARCH 2013

DOCUMENT #: TEST-MASTERTP0023-004 (1MAR13)

FORCE PROTECTION BRANCH

AIR FORCE LIFE CYCLE MANAGEMENT CENTER (AFLCMC)

HANSCOM AIR FORCE BASE, MA 01731-2100

i

TABLE OF CONTENTS

Section Page

LIST OF FIGURES ................................................................................................................................... vi

LIST OF TABLES ..................................................................................................................................... vi

SECTION I. INTRODUCTION ............................................................................................................ 1-1

1.1 PURPOSE ..................................................................................................................................... 1-1

1.2 APPLICABILITY ......................................................................................................................... 1-1

1.3 REFERENCED DOCUMENTS ................................................................................................... 1-1

1.4 SECURITY CLASSIFICATION .................................................................................................. 1-1

1.5 REPORTS AND CORRESPONDENCE ..................................................................................... 1-2

1.6 HOTLINE ..................................................................................................................................... 1-2

SECTION 2. GENERAL TEST REQUIREMENTS ........................................................................... 2-1

2.1 INTRODUCTION ........................................................................................................................ 2-1

2.2 METHOD OF TESTING .............................................................................................................. 2-1

2.3 RESPONSIBLE TEST ORGANIZATION .................................................................................. 2-1

2.4 TEST PERSONNEL ..................................................................................................................... 2-2

2.5 TEST REQUIREMENTS ............................................................................................................. 2-2

2.5.1 Phase I Testing ................................................................................................................. 2-3

2.5.2 Phase II Testing ............................................................................................................... 2-4

2.5.3 Phase III Testing .............................................................................................................. 2-4

2.6 SYSTEM ACCEPTANCE............................................................................................................ 2-5

2.6.1 Pass/Fail Test Criteria ...................................................................................................... 2-5

2.7 CORRECTION OF DEFICIENCIES ........................................................................................... 2-6

2.8 TEST DOCUMENTATION ......................................................................................................... 2-6

2.9 SECURITY CLASSIFICATION .................................................................................................. 2-7

SECTION 3. COMMAND CONTROL AND DISPLAY EQUIPMENT (CCDE) ............................ 3-1

3.1 INTRODUCTION ........................................................................................................................ 3-1

3.2 APPLICABLE DOCUMENTS .................................................................................................... 3-1

3.3 TEST OBJECTIVE ....................................................................................................................... 3-1

3.4 SYSTEM ACCEPTANCE STANDARD ..................................................................................... 3-1

3.5 CCDE TEST SEQUENCE ........................................................................................................... 3-1

3.6 PHASED FUNCTIONAL TESTING ........................................................................................... 3-2

3.6.1 Phase I Functional Testing ............................................................................................... 3-2

3.6.2 Phase II 72 Hour Monitoring and Operational Test ......................................................... 3-2

3.6.3 Phase III 30 Day Operational Test ................................................................................... 3-2

3.7 CCDE TEST OBJECTIVES ......................................................................................................... 3-2 ii

TABLE OF CONTENTS (Cont.)

SECTION 4. PERIMETER SURVEILLANCE SYSTEM, CLOSED CIRCUIT

TELEVISION (PSS-CCTV) ......................................................................................... 4-1

4.1 INTRODUCTION ........................................................................................................................ 4-1

4.2 APPLICABLE DOCUMENTS .................................................................................................... 4-1

4.3 TEST OBJECTIVE ....................................................................................................................... 4-1

4.4 ACCEPTANCE STANDARD ...................................................................................................... 4-1

4.5 PHASED FUNCTIONAL TESTING ........................................................................................... 4-1

4.5.1 Phase I Functional Testing ............................................................................................... 4-1

4.5.2 Test Equipment ................................................................................................................ 4-2

4.5.3 Test Sequence .................................................................................................................. 4-2

4.5.4 CCTV Functional Test ..................................................................................................... 4-2

4.5.5 CCTV Terminal/Junction Box Tamper and Line Fault Test ........................................... 4-2

4.5.6 CCTV AC Power Loss Test ............................................................................................. 4-3

4.5.7 CCTV Intrusion Detection Tests ..................................................................................... 4-3

4.5.8 Phase II 72 Hour Monitoring and Operational Test ......................................................... 4-3

4.5.9 Phase III 30 Day Operational Test ................................................................................... 4-4

SECTION 5. INTERIOR INTRUSION DETECTION SYSTEM (IIDS) .......................................... 5-1

5.1 INTRODUCTION ........................................................................................................................ 5-1

5.2 APPLICABLE DOCUMENTS .................................................................................................... 5-1

5.3 TEST OBJECTIVE ....................................................................................................................... 5-1

5.4 ACCEPTANCE STANDARD ...................................................................................................... 5-1

5.5 PHASED FUNCTIONAL TESTING ........................................................................................... 5-2

5.5.1 Phase I Functional Testing ............................................................................................... 5-2

5.5.2 Test Equipment ................................................................................................................ 5-2

5.5.3 Test Sequence .................................................................................................................. 5-2

5.5.4 Sensor Tamper and Line Fault Tests ............................................................................... 5-2

5.5.5 Interior Sensor Intrusion Detection Tests ........................................................................ 5-3

5.5.5.1 Intrusion Lanes ................................................................................................ 5-3

5.5.5.2 Ground Level Intrusion Detection Tests ......................................................... 5-3

5.5.5.3 Overhead Intrusion Detection Tests ................................................................ 5-4

5.5.6 Backup Battery 4 Hour Operational Test ......................................................................... 5-4

5.5.7 Phase II 72 Hour Monitoring and Operational Test ......................................................... 5-5

5.5.8 Phase III 30 Day Operational Test ................................................................................... 5-5

SECTION 6. ACCESS CONTROL SYSTEM (ACS) .......................................................................... 6-1

6.1 INTRODUCTION ........................................................................................................................ 6-1

6.1.1 Access Control Devices ................................................................................................... 6-1

6.1.2 Portals .............................................................................................................................. 6-2

6.2 APPLICABLE DOCUMENTS .................................................................................................... 6-2

6.3 TEST OBJECTIVE ....................................................................................................................... 6-2

6.4 ACCEPTANCE STANDARD ...................................................................................................... 6-2

6.5 PHASED FUNCTIONAL TESTING ........................................................................................... 6-2

6.5.1 Phase I Functional Testing ............................................................................................... 6-2 iii

6.5.2 Test Equipment ................................................................................................................ 6-2

6.5.3 ACS Functional Tests ...................................................................................................... 6-3

6.5.4 ACS Test Objectives ........................................................................................................ 6-3

6.5.5 Phase II 72 Hour Monitoring and Operational Test ......................................................... 6-4

6.5.6 Phase III 30 Day Operational Test ................................................................................... 6-4

SECTION 7. FENCE SENSOR ............................................................................................................. 7-1

7.1 INTRODUCTION ........................................................................................................................ 7-1

7.2 APPLICABLE DOCUMENTS .................................................................................................... 7-1

7.3 TEST OBJECTIVE ....................................................................................................................... 7-1

7.4 ACCEPTANCE STANDARD ...................................................................................................... 7-1

7.5 PHASED FUNCTIONAL TESTING ........................................................................................... 7-1

7.5.1 Phase I Functional Testing ............................................................................................... 7-2

7.5.2 Test Equipment ................................................................................................................ 7-2

7.5.3 Test Sequence .................................................................................................................. 7-2

7.5.4 Fence Sensor Tamper and Line Supervision Tests .......................................................... 7-2

7.5.5 Fence Sensor Tap Intrusion Detection Tests ................................................................... 7-3

7.5.6 Backup Battery 4 Hour Operational Test ......................................................................... 7-3

7.5.7 Phase II 72 Hour Monitoring and Operational Test ......................................................... 7-4

7.5.8 Phase III 30 Day Operational Test ................................................................................... 7-4

SECTION 8. BURIED LINE SENSOR ................................................................................................ 8-1

8.1 INTRODUCTION ........................................................................................................................ 8-1

8.2 APPLICABLE DOCUMENTS .................................................................................................... 8-1

8.3 TEST OBJECTIVE ....................................................................................................................... 8-1

8.4 ACCEPTANCE STANDARD ...................................................................................................... 8-1

8.5 PHASED FUNCTIONAL TESTING ........................................................................................... 8-2

8.5.1 Phase I Functional Testing ............................................................................................... 8-2

8.5.2 Test Equipment ................................................................................................................ 8-2

8.5.3 Test Sequence .................................................................................................................. 8-2

8.5.4 Tamper and Line Supervision Tests ................................................................................ 8-2

8.5.5 Intrusion Detection Vehicle Tests .................................................................................... 8-3

8.5.6 Intrusion Detection Walk Tests ....................................................................................... 8-3

8.5.7 Intrusion Detection Run and Jump Tests ......................................................................... 8-3

8.5.8 Intrusion Detection Human Crawl Tests .......................................................................... 8-4

8.5.9 Backup Battery 4 Hour Operational Test ......................................................................... 8-4

8.5.10 Phase II 72 Hour Monitoring and Operational Test ......................................................... 8-5

8.5.11 Phase III 30 Day Operational Test ................................................................................... 8-5

SECTION 9. ABOVE GROUND PERIMETER INTRUSION DETECTION SYSTEM (IDS) .... 9-1

9.1 INTRODUCTION ........................................................................................................................ 9-1

9.2 APPLICABLE DOCUMENTS .................................................................................................... 9-1

9.3 TEST OBJECTIVE ....................................................................................................................... 9-1 iv

9.4 ACCEPTANCE STANDARD ...................................................................................................... 9-1

9.5 PHASED FUNCTIONAL TESTING ........................................................................................... 9-2

9.5.1 Phase I Functional Testing ............................................................................................... 9-2

9.5.2 Test Equipment ................................................................................................................ 9-2

9.5.3 Test Sequence .................................................................................................................. 9-2

9.5.4 Tamper and Line Supervision Tests ................................................................................ 9-2

9.5.5 Intrusion Detection Tests ................................................................................................. 9-3

9.5.5.1 Intrusion Detection Vehicle Tests ................................................................... 9-3

9.5.5.2 Intrusion Detection Walk Tests ....................................................................... 9-3

9.5.5.3 Intrusion Detection Run and Jump Tests ......................................................... 9-4

9.5.5.4 Intrusion Detection Human Crawl Tests ......................................................... 9-4

9.5.5.5 Intrusion Detection Post-Climb/Jump Tests

(applies only to sensors installed on posts) ..................................................... 9-4

9.5.5.6 Beam Intrusion Detection Tests (applies only to active IR sensors) ............... 9-4

9.5.6 Battery Backup 4 Hour Operational Test ......................................................................... 9-5

9.5.7 Phase II 72 Hour Monitoring and Operational Test ......................................................... 9-5

9.5.8 Phase III 30 Day Operational Test ................................................................................... 9-6

SECTION 10. BALANCED MAGNETIC SWITCH (BMS) ............................................................ 10-1

10.1 INTRODUCTION ...................................................................................................................... 10-1

10.2 APPLICABLE DOCUMENTS .................................................................................................. 10-1

10.3 TEST OBJECTIVE ..................................................................................................................... 10-1

10.4 ACCEPTANCE STANDARD .................................................................................................... 10-1

10.5 PHASED FUNCTIONAL TESTINGS ....................................................................................... 10-2

10.5.1 Phase I Functional Testing ............................................................................................. 10-2

10.5.2 Test Equipment .............................................................................................................. 10-2

10.5.3 Test Sequence ................................................................................................................ 10-2

10.5.4 BMS Tamper Tests ........................................................................................................ 10-2

10.5.5 BMS Intrusion Tests ...................................................................................................... 10-2

10.5.6 Phase II 72 Hour Monitoring and Operational Test ....................................................... 10-3

10.5.7 Phase III 30 Day Operational Test ................................................................................. 10-3

SECTION 11. VIDEO STORAGE SYSTEM (VSS) .......................................................................... 11-1

11.1 INTRODUCTION ...................................................................................................................... 11-1

11.2 APPLICABLE DOCUMENTS .................................................................................................. 11-1

11.3 TEST OBJECTIVE ..................................................................................................................... 11-1

11.4 ACCEPTANCE STANDARD .................................................................................................... 11-1

11.5 PHASED FUNCTIONAL TESTING ......................................................................................... 11-1

11.5.1 Phase I Functional Testing ........................................................................................... 11-2

11.5.2 Test Equipment ............................................................................................................ 11-2

11.5.3 VSS Test Sequence ...................................................................................................... 11-2

11.5.4 VSS Tamper Tests ........................................................................................................ 11-2

11.5.5 VSS Line Fault Tests.................................................................................................... 11-2

11.5.6 VSS AC Power Loss Tests ........................................................................................... 11-2

11.5.7 VSS Intrusion Detection Test ....................................................................................... 11-3 v

11.5.8 Battery Backup 4 Hour Operational Test ..................................................................... 11-3

11.5.9 Phase II 72 Hour Monitoring and Operational Test ..................................................... 11-4

11.5.10 Phase III 30 Day Operational Test ............................................................................... 11-4

SECTION 12. VIDEO MOTION DETECTION (VMD) .................................................................. 12-1

12.1 INTRODUCTION ...................................................................................................................... 12-1

12.2 APPLICABLE DOCUMENTS .................................................................................................. 12-1

12.3 TEST OBJECTIVE ..................................................................................................................... 12-1

12.4 ACCEPTANCE STANDARD .................................................................................................... 12-1

12.5 PHASED FUNCTIONAL TESTING .........................................................