EngineeringInstructions.pdf
PDF 81 KB Posted
- Attached to
- UMTE Control, Interface Federal contract opportunity
- Solicitation number
- SPRHA5-25-Q-0415
- Issued by
- Defense Logistics Agency Aviation
About this file
This is an Engineering Instructions document (Hill AFB Form 462) that provides manufacturing requirements for Part Number 9805-7210-1 (National Stock Number: 5895015121931) for the Defense Logistics Agency Aviation.
The document outlines specific requirements for Unique Identification (UID) labeling per MIL-STD-130, including both human-readable text (minimum 1/8th inch) and machine-readable 2D matrix (minimum 1/4 inch square) specifications. Both must include CAGE (17V), Part Number (1P), and Serial Number (1S). The contractor must certify full compliance with all drawings, specifications, and standards prior to contract award, and any deviations require prior approval from the cognizant engineering activity. The system engineer retains rights to review and accept discrepant items before shipment. The document specifies that military specifications/standards will not be furnished in the bid set, and material substitutions require prior engineering approval.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| CDRLCPP.pdf | ||
| SPRHA525Q0415.pdf | ||
| CDRLFATP.pdf | ||
| CDRLFATR.pdf | ||
| SOW.pdf |
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
REV:
ENGINEERING INSTRUCTIONS
NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.
1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:
2. PART NUMBER: 9805-7210-1
3. NATIONAL STOCK NUMBER: 5895015121931
PREPARED BY: Andrew Webb OFFICE SYMBOL: 415 SCMS
DATE: 12/26/2024
HILL AFB FORM 462
4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC., WILL BE USED IN LIEU OF THE DATA INDICATED. THE SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.i
5. THE SOURCES/MATERIALS IF LISTED ON THE STANDARDS, SPECIFICATION AND DRAWINGS ARE THE ONLY SOURCES/MATERIALS FOR THOSE ITEMS. SUBSTITUTIONS SHALL HAVE PRIOR APPROVAL BY THE COGNIZANT ENGINEERING ACTIVITY.
6. DEVIATIONS FROM SPECIFICATIONS IDENTIFIED IN CONTROL DRAWINGS ARE NOT AUTHORIZED WITHOUT PRIOR APPROVAL BY
THE COGNIZANT ENGINEERING ACTIVITY.
7. SYSTEM ENGINEER RETAINS ALL RIGHTS TO REVIEW AND ACCEPT DISCREPANT ITEM PRIOR TO SHIPMENT. ANY DEVIATION FROM THE ENGINEERING DRAWING SHALL BE SUBMITTED FOR ENGINEERING REVIEW AND DISPOSITION.
8. PRIOR TO CONTRACT AWARD, THE CONTRACTOR SHALL CERTIFY TO THE GOVERNMENT IN WRITING FULL COMPLIANCE WITH DRAWINGS, SPECIFICATIONS AND STANDARDS CALLED OUT AND REQUIRED FOR THE MANUFACTURE OF THIS ASSEMBLY. THE CONTRACTOR IS RESPONSIBLE TO COMPLETELY SEARCH THESE DRAWINGS, SPECIFICATIONS AND STANDARDS AND FULLY
UNDERSTAND THE REQUIREMENTS NECESSARY TO MANUFACTURE THE ITEM.
9. UNIQUE IDENTIFICATION (UID) SHALL BE APPLIED PER MIL-STD-130:
a. MINIMUM 1/8TH INCH ON HUMAN READABLE TO INCLUDE:
i. CAGE (17V)
ii. P/N (1P)
iii. SERIAL NUMBER (1S)
b. MINIMUM 1/4 INCH SQUARE ON MACHINE READABLE 2D MATRIX – CONSTRUCT 2 – TO INCLUDE:
i. CAGE (17V)
ii. P/N (1P)
iii. SERIAL NUMBER (1S)
c. LABEL SHALL CONTAI/N ALL DATA ON EXISTING LABEL, IF EXISTING LABEL IS TO BE REPLACED.
d. SAME LABEL MATERIAL SHALL BE USED AS SPECIFIED IN DRAWING FOR EXISTING LABEL.
e. MIL-STD-130, ANSI/AIM BCII, ISO 15434, ISO 15415, AND ISO 15418.
REV:
ENGINEERING INSTRUCTIONS
NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.
1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:
2. PART NUMBER: 9805-7210-1
3. NATIONAL STOCK NUMBER: 5895015121931
PREPARED BY: Andrew Webb OFFICE SYMBOL: 415 SCMS
DATE: 12/26/2024
HILL AFB FORM 462
i
File details come from the government source that posted it. Updated .