EDR.pdf

REV: ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

POWER SUPPLY, AC

2. PART NUMBER:

6014810-001

3. NATIONAL STOCK NUMBER:

6130-01-686-1340WF

PREPARED BY:

NEAL BOEHMER

OFFICE SYMBOL:

416 SCMS/GUMAA

DATE:

20210517

HILL AFB FORM 462 Page 1 of 2

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC., WILL BE USED IN LIEU OF THE DATA INDICATED. THE

SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.

5. THE SOURCES/MATERIALS IF LISTED ON THE SPECIFICATION, STANDARDS AND DRAWINGS ARE THE ONLY SOURCES/MATERIALS FOR THOSE ITEMS. ANY SUBSTITUTIONS SHALL HAVE PRIOR APPROVAL BY THE COGNIZANT

ENGINEERING ACTIVITY.

6. DEVIATIONS FROM SPECIFICATIONS IDENTIFIED IN CONTROL DRAWINGS ARE NOT AUTHORIZED WITHOUT PRIOR

APPROVAL FROM THE COGNIZANT ENGINEERING.

7. PART MARKING AS PER MIL-STD-130.

8. THIS IS AN AIRCRAFT PART. USE THE APPROPRIATE PORTION OF MIL-STD-2000 THAT APPLIES TO AIRCRAFT SOLDERING FOR ALL SOLDERING REQUIREMENTS. *NOTE: J-STD-001 MAY BE USED IN LIEU OF MILS-STD-2000, IF

SPECIFICATION MEETS OR EXCEEDS MIL-STD-2000

8.1 EFFECTIVE 9 MAY 2005 THE DEPARTMENT OF THE AIR FORCE ISSUED AN AIR WORTHINESS ADVISORY (M-05-01) REGARDING THE USE OF LEAD-FREE SOLDER IN ELECTRICAL AND ELECTRONIC MILITARY PRODUCTS. TO DATE, NO LEAD-FREE SOLDER FORMULATION HAS MATCHED THE RELIABILITY AND PERFORMANCE QUALITIES OF THE STANDARD LEADED SOLDERS. THEREFORE, UNTIL SUCH TIME AS A SUITABLE, RELIABLE LEAD-FREE SOLDER REPLACEMENT IS IDENTIFIED, ALL ELECTRONIC EQUIPMENT SUPPLIERS SHALLCONTINUE TO PROVIDE THE DEPARTMENT OF THE AIR FORCE WITH ITEMS WHICH MEET ALL PERFORMANCE, COMPATIBILITY, AND RELIABILITY STANDARDS PREVIOUSLY ESTABLISHED WITH LEADED SOLDERS. FAILURE TO DO SO, COULD ADVERSELY IMPACT

THE PERFORMANCE AND RELIABILITY OF WEAPON SYSTEMS AFFECTING NATIONAL SECURITY.

8.2 THE USE OF LEAD-FREE SOLDER OR LEAD-FREE PLATED COMPONENTS IN MILITARY ELECTRONIC PRODUCTS IS CONSIDERED A FLIGHT SAFETY AND NATIONAL SECURITY CONCERN. FOR THIS REASON THE US AIR FORCE WANTS TO BE NOTIFIED WHEN LEAD-FREE COMPONENTS AND MANUFACTURING PROCESSES HAVE BEEN IMPLEMENTED. AS PART OF SATISFACTORY COMPLIANCE WITH THE REQUIREMENTS OF THIS CONTRACT THE US AIR FORCE REQUIRES NOTIFICATION ON A NO-COST BASIS WHEN ANY OF THE FOLLOWING CONDITIONS EXIST:1. COMMERCIAL OFF-THE- SHELF (COTS) OR ANY OTHER ELECTRICAL COMPONENTS THAT CONTAIN LEAD-FREE SOLDER OR LEAD-FREE PLATED COMPONENTS ARE USED IN THE END-ITEM. 2. ANY LEAD-FREE COMPONENT OR PART USED TO MANUFACTURE THE END

ITEM THAT IS NOT IDENTIFIED WITH A SEPARATE PART NUMBER OR DESIGNATION.

8.3 IF NO LEAD-FREE, LEAD-FREE PLATED COTS OR ANY OTHER LEAD-FREE ELECTRICAL OR ELECTRONICS COMPONENTS EXIST IN THE MANUFACTURED END ITEM, THE CONTRACTOR SHALL PROVIDE WRITTEN CERTIFICATION OF COMPLIANCE AS A DELIVERABLE WITH THE CONTRACT.1. USE INDUSTRY STANDARD IPC-1066, "MARKING, SYMBOLS AND LABELS FOR IDENTIFICATION OF LEAD-FREE AND OTHER REPORTABLE MATERIALS IN LEAD-FREE ASSEMBLIES, COMPONENTS AND DEVICES," 2. INCLUDE THE PROGRAM ENGINEER'S EVALUATION OF THE PURCHASING/REPAIR ITEM FOR ANY "LEAD-FREE" MILITARY PART(S) IN REFERENCE TO ITS' RELIABILITY, PERFORMANCE AND COMPATIBILITY

FOR THE SYSTEM.

8.4 POC FOR THIS MATTER IS THE ENGINEERING SUPPORT ACTIVITY (ESA).

REV: ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

POWER SUPPLY, AC

2. PART NUMBER:

6014810-001

3. NATIONAL STOCK NUMBER:

6130-01-686-1340WF

PREPARED BY:

NEAL BOEHMER

OFFICE SYMBOL:

416 SCMS/GUMAA

DATE:

20210517

HILL AFB FORM 462 Page 2 of 2

9 UNIQUE IDENTIFICATION (UID) SHALL BE APPLIED PER MIL-STD-130:

A. MINIMUM 1/8TH INCH ON HUMAN READABLE TO INCLUDE:

1. CAGE (17V)

2. P/N (1P)

3. SERIAL NUMBER (1S)

B. MINIMUM 1/4 INCH SQUARE ON MACHINE READABLE 2D MATRIX – CONSTRUCT 2 – TO

INCLUDE:

1. CAGE (17V)

2. P/N (1P)

3. SERIAL NUMBER (1S)

C. LABEL SHALL CONTAIN ALL DATA ON EXISTING LABEL, IF EXISTING LABEL IS TO BE

REPLACED.

D. SAME LABEL MATERIAL SHALL BE USED AS SPECIFIED IN DRAWING FOR EXISTING

LABEL.

E. MIL-STD-130, ANSI/AIM BCII, ISO 15434, ISO 15415, AND ISO 15418.