EDR.pdf

REV: ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF A:

Cover Assy, Rocket Nozzle Fwd Shroud

2. PART NUMBER:

71E45331G2

3. NATIONAL STOCK NUMBER:

1420-00-005-1716

PREPARED BY:

ALAN J LOVELESS

OFFICE SYMBOL:

414 SCMS/GUEA

DATE:

12/8/20

HILL AFB FORM 462 Page 1 of 1

4. A supportability analysis was completed for this part, which shows that all materials and components are available. See Appendix A. This information is available to help with the purchasing process, but its use is not mandatory.

5. Make the following change to 71C45188, Note 5 as follow:

WAS: APPLY LUBRICANT 165A4432P1 PER 165A4435 (PARA 4.10.3 NOT REQD) TO ALL SURFACES. (PARA 3.3.1.2 APPLIES

ONLY TO SURFACES X &Y)

IS: APPLY LUBRICANT 165A4432P1 PER 165A4435 (PARA 4.10.3 NOT REQD) TO ALL SURFACES. (PARA 3.3.1.2 APPLIES

ONLY TO SURFACES X&Y). ALTERNATE LUBRICANT IS MOLYKOTE® D-321R APPLIED TO ALL SURFACES PER THE

MANUFACTURER'S INSTRUCTIONS.

6. Make the following changes to 71C45189, Note 5 as follows:

WAS: APPLY LUBRICANT ITEM 3 PER 165A4435 (PARA 4.10.3 NOT REQ'D) TO WEDGE BLOCK, ITEM1, PRIOR TO INSTL OF

NUT PLATE, ITEM 2. (PARA 3.3.1.2 APPLIES ONLY TO SURFACES X &Y)

IS: APPLY LUBRICANT ITEM 3 PER 165A4435 (PARA 4.10.3 NOT REQ'D) TO WEDGE BLOCK, ITEM1, PRIOR TO INSTL OF

NUT PLATE, ITEM 2. (PARA 3.3.1.2 APPLIES ONLY TO SURFACES X &Y). OR APPLY ALTERNATE LUBRICANT, ALT

ITEM 3, TO WEDGE BLOCK, ITEM 1, PRIOR TO INSTL OF NUT PLATE, ITEM 2, PER THE MANUFACTURER'S

INSTRUCTIONS.

7. Make the following changes to 71C45189G1 as follows:

Add alternate lubricant (Item 3) MOLYKOTE D-321R from Dupont (cage 818U1).

8. Make the following change to 71E45331G2 as follow:

EO 15A0220-H will be superseded by a new EO and, as a result, the IUID requirement is deleted for this part.

Appendix A

Supportability Analysis (71E45331G2)

6/2/2021

Item Number

Part No. Vendor Part No. NSN Noun OEM/ CAGE Source/ CAGE Source Contact Information Procurable?

Review

Date Comments

1 71D46133P1 Ti-6AL-4V per MIL-T- 9046, type III, Comp C, except O2 <= 0.14%

None COVER, ROCKET NOZZLE - FWD SHROUD ? Fab Shop Fab Shop 5/21/21

MIL-T-9046 is cancelled and replaced by SAE-AMS-T-9046, which is also cancelled and replaced by several AMS specs. Sent email to Jim Rawlinson to see if we can still get this Ti and what the new spec call out would be. Jim recommends SAE AMS4907, which is an active spec. 3/25/21. It turns out that this material is still available to the old spec. 3/30/21.

3 71C45188P1 Ti-6AL-4V per MIL-T- 9046, type III, Comp C, except O2 <= 0.14%

None

LATCH-STOP ROCKET NOZZLE COVER - FWD

SHROUD

? Fab Shop Fab Shop 5/21/21

MIL-T-9046 is cancelled and replaced by SAE-AMS-T-9046, which is also cancelled and replaced by several AMS specs. Sent email to Jim Rawlinson to see if we can still get this Ti and what the new spec call out would be. Jim recommends SAE AMS4907, which is an active spec. 3/25/21. It turns out that this material is still available to the old spec. 3/30/21. I need an EO and EI to add 321R alt and process.

5/21/21.

3.1 165A4432P1 Molyote X-15 Alternate added via new EO is Molykote D-321R

None

SOLID FILM LUBRICANT, MOLYDISULFIDE-

GRAPHITE

Dow Corning Corp., 50 Commerce Dr., Trumbull, CT 06611, Cage 94499, 800-258- Dupont De Nemours, Inc. cage = 818U1

Chempoint, Cage 3CU95 Kaku Ansah, 425-372-9501, kaku.ansah@chempoint.com 5/21/21

None in ILS. Source controlled. Dupont merged with Dow then separated April 2019 and Dupont (833-338-7668, Kim) took the Molykote products and may still make this stuff. She is having her tech folks look into it and will call me within a couple of days. I compared Molykote X-12 to Molykote 321, used on the V-Band, and they are not the same. 321 is a non-graphite spray Molykote and the X-12 has graphite and is sprayed on with spray equipment. 321 might replace X-15. Lets see what Dupont says. Robin Gray (robin.gray@dupont.com) emailed and asked a question about X-15. I responded and sent her copies of the material and process specs. 5/11/21. Robin could'nt find a drop in replacement. She recommends MOLYKOTE® D-7409. Pete would rather go with MOLYKOTE D-321R. Dupont's cage is 818U1. 6/2/21.

4 71C45190P1 Ti-6AL-4V per MIL-T- 9046, type III, Comp C, except O2 <= 0.14%

1420-00-004-5436 DLA Mgt

LATCH TAB, ROCKET NOZZLE COVER FWD

SHROUD

? Fab Shop Fab Shop 5/21/21

MIL-T-9046 is cancelled and replaced by SAE-AMS-T-9046, which is also cancelled and replaced by several AMS specs. Sent email to Jim Rawlinson to see if we can still get this Ti and what the new spec call out would be. Jim recommends SAE AMS4907, which is an active spec. 3/25/21. It turns out that this material is still available to the old spec. 3/30/21. This drawing does not need an X-15 EO since I did EO 17A0115-H back in 2017. 5/21/21.

4.1 165A4432P1 Molykote X-15 None

SOLID FILM LUBRICANT, MOLYDISULFIDE-

GRAPHITE

Dow Corning Corp., 50 Commerce Dr., Trumbull, CT 06611, Cage 94499, 800-258- Dupont De Nemours, Inc. cage = 818U1

Chempoint, Cage 3CU95 Kaku Ansah, 425-372-9501, kaku.ansah@chempoint.com 5/21/21

None in ILS. Source controlled. Dupont merged with Dow then separated April 2019 and Dupont (833-338-7668, Kim) took the Molykote products and may still make this stuff. She is having her tech folks look into it and will call me within a couple of days. I compared Molykote X-12 to Molykote 321, used on the V-Band, and they are not the same. 321 is a non-graphite spray Molykote and the X-12 has graphite and is sprayed on with spray equipment. 321 might replace X-15. Lets see what Dupont says. Robin Gray (robin.gray@dupont.com) emailed and asked a question about X-15. I responded and sent her copies of the material and process specs. 5/11/21. Robin could'nt find a drop in replacement. She recommends MOLYKOTE® D-7409. Pete would rather go with MOLYKOTE D-321R. Dupont's cage is 818U1. 6/2/21.

4.2 165A4432P1 ALT Molykote D-321R None

SOLID FILM LUBRICANT, MOLYDISULFIDE-

GRAPHITE

Dupont/ 833-338-7668 Chempoint, Cage 3CU95 Kaku Ansah, 425-372-9501, kaku.ansah@chempoint.com 5/21/21 EO 17A0115-H adds D321R has an alternate. Yea!

5 71C45189G1 NA

1420-00-004-5435 DLA Mgt

WEDGE BLOCK, ROCKET NOZZLE COVER - FWD

SHROUD

NA NA NA NA 5/21/21

Parts list only. Need an EO to add D321R as an alternate to Item 3 (X-15). Need an EO to change 71C45189, note 5 to add alternate process.

5.1 71C45189P1 Ti-6AL-4V per MIL-T- 9046, type III, Comp C, except O2 <= 0.14%

None

WEDGE BLOCK, ROCKET NOZZLE COVER - FWD

SHROUD

? Fab Shop Fab Shop 5/21/21

MIL-T-9046 is cancelled and replaced by SAE-AMS-T-9046, which is also cancelled and replaced by several AMS specs. Sent email to Jim Rawlinson to see if we can still get this Ti and what the new spec call out would be. Jim recommends SAE AMS4907, which is an active spec. 3/25/21. It turns out that this material is still available to the old spec. 3/30/21.

5.2 74A54875P1 NAS 1068-C08 None

NUT, PLATE, SELF-LOCKING, TWO-LUG, FLOATING

- NAS 1068

Kaynar Mfg. Co., Inc.

800 S. State collage Blvd., Fullerton, CA 92631 Cage = 15653

ILS ILS 5/21/21

0.1640-32 UNJC-3B Thread. Kaynar is now Howmet Global Fastening Systems. Ken Paine (805-426-2270). Many sources in ILS under NAS 1068-C08.

5.3 165A4432P1 Molykote X-15 None

SOLID FILM LUBRICANT, MOLYDISULFIDE-

GRAPHITE

Dow Corning Corp., 50 Commerce Dr., Trumbull, CT 06611, Cage 94499, 800-258- Dupont De Nemours, Inc. cage = 818U1

Chempoint, Cage 3CU95 Kaku Ansah, 425-372-9501, kaku.ansah@chempoint.com 5/21/21

None in ILS. Source controlled. Dupont merged with Dow then separated April 2019 and Dupont (833-338-7668, Kim) took the Molykote products and may still make this stuff. She is having her tech folks look into it and will call me within a couple of days. I compared Molykote X-12 to Molykote 321, used on the V-Band, and they are not the same. 321 is a non-graphite spray Molykote and the X-12 has graphite and is sprayed on with spray equipment. 321 might replace X-15. Lets see what Dupont says. Robin Gray (robin.gray@dupont.com) emailed and asked a question about X-15. I responded and sent her copies of the material and process specs. 5/11/21. Robin could'nt find a drop in replacement. She recommends MOLYKOTE® D-7409. Pete would rather go with MOLYKOTE D-321R. Dupont's cage is 818U1. 6/2/21.

5.4 MS20427M3-8 NA

5320-00-118-2002 DLA Mgt

RIVET, SOLID - 100° COUNTERSUNK HEAD,

CARBON STEEL, CORROSION-RESISTANT STEEL,

MONEL AND COPPER

? ILS ILS 5/21/21 Lots in ILS.

8 MS20427M4-8 NA

5320-00-118-2007 DLA Mgt

RIVET, SOLID - 100° COUNTERSUNK HEAD,

CARBON STEEL, CORROSION-RESISTANT STEEL,

MONEL AND COPPER

? ILS ILS 5/21/21 Lots in ILS.

9 NAS1221-08E6 NA

5305-01-027-4626 DLA Mgt

BOLT,100° FLUSH HEAD, SELF-LOCKING

OPTIONAL

? ILS ILS 5/21/21 Lots in ILS.

10 NAS1221-3E4 NA

5305-00-551-4844 DLA Mgt

BOLT, 100° FLUSH HEAD, SELF-LOCKING

OPTIONAL

? ILS ILS 5/21/21 Lots in ILS.

11 NAS1022C3 NA 5310-00-685-3515

NUT, SELF-LOCKING, HEXAGON-LOW HEIGHT,

LOW STRENGTH

? ILS ILS 5/21/21 Lots in ILS.

11 ALT NAS679C3 NA

5310-00-680-9301 5310-00-722-5779

NUT, SELF-LOCKING, HEXAGON-LOW HEIGHT ? ILS ILS 5/21/21 Lots in ILS.

Procurable from AF Supply Procurable from DLA Supply

Part Number Being Evaluated: 71E45331G2 Cover Assy, Rocket Nozzle, FWD Shroud (Need an EO to rescind the IUID EO 15A0220-H to be consistant with EO 21A3072-H (71E45331), which deleted IUID requirements.)

Procurable from the OEM Procurable from a source other than the OEM Not procurable from anyone - possible project Procurable from surplus in original packaging

12 71A45568P11 Scotchcal 220 Clear Enamel, PN P27324A

None DECAL, ELASTOMERIC, PIGMENTED

National Decalcomania Corp., 5548-54 Chestnut Street, Philadelphia, PA 19139, Cage = 97091

Any Label Mfg. Any Label Mfg. 5/21/21

Now known as National Delcalcraft Corp. No SAM or current cage. 2750 Bethlehem Pike, Hatfield, PA. EO 18A0734-H allows an alternate material from Gerber Technology (Scotchcal 220 Clear Enamel, PN P27324A). Assume any lable mfg could buy this material and make the lable.

13 71C46080G1 NA None STRAP ASSEMBLY, COVER-FWD SHROUD NA NA NA NA 5/21/21 Parts list only

13.1 71C46080P1 Ti-6AL-4V per MIL-T- 9046, type III, Comp C, except O2 <= 0.14%

None STRAP ? Fab Shop Fab Shop 5/21/21

MIL-T-9046 is cancelled and replaced by SAE-AMS-T-9046, which is also cancelled and replaced by several AMS specs. Sent email to Jim Rawlinson to see if we can still get this Ti and what the new spec call out would be. Jim recommends SAE AMS4907, which is an active spec. 3/25/21. It turns out that this material is still available to the old spec. 3/30/21.

13.2 71C45187P1 Ti-6AL-4V per MIL-T- 9046, type III, Comp C, except O2 <= 0.14%

None HINGE, ROCKET NOZZLE COVER - FWD SHROUD ? Fab Shop Fab Shop 5/21/21

MIL-T-9046 is cancelled and replaced by SAE-AMS-T-9046, which is also cancelled and replaced by several AMS specs. Sent email to Jim Rawlinson to see if we can still get this Ti and what the new spec call out would be. Jim recommends SAE AMS4907, which is an active spec. 3/25/21. It turns out that this material is still available to the old spec. 3/30/21.

13.3 MS20427M4-4 NA

5320-00-118-2005 DLA Mgt

RIVET, SOLID - 100° COUNTERSUNK HEAD,

CARBON STEEL, CORROSION-RESISTANT STEEL,

MONEL AND COPPER

? ILS ILS 5/21/21 Lots in ILS.

14 NAS1221-08E2 NA

5305-01-131-2895 DLA Mgt

BOLT, 100° FLUSH HEAD, SELF-LOCKING

OPTIONAL

? ILS ILS 5/21/21 Lots in ILS.

16 AN960C8 NA

5310-00-685-3744 5310-01-352-9572 DLA Mgt

WASHER, FLAT ? ILS ILS 5/21/21 Lots in ILS.

17 MS21043-08 NA

5310-01-505-2644 5310-00-878-7196

NUT, SELF-LOCKING, 800° F, REDUCED HEXAGON

REDUCED HEIGHT, RING BASE, CORROSION

RESISTANT STEEL

? ILS ILS 5/21/21 Lots in ILS.

18 128A5490P1

SR 585

GE SR585

None PRESSURE SENSITIVE SILICONE ADHESIVE GE Silicone Products Dept., Waterford, N.Y.

Dynamation Research Etty Rotman (Dynamation), 310-477-1224, etty@dynamation.com 5/21/21

One source in ILS (Dynamation). GE Silicone sold to Momentive Performance Materials Inc. in 2006. Cage = 01139, 704-805-6946. Left a v-mail. 5/26/21. Dean at Momentive says that SR 585 is not a good PN. I need to send an email to commercial.services@momentive.com to see if they can find SR 585. Sent email to Dynamation (rfq@dynamation.com) to see if they can get SR 585 like ILS says. I also requested a quote. Dynamation can get this material. 5/27/21

19 72D21339P1 NA

1420-01-035-4390 DLA Mgt

SHIELD, THERMAL PROTECTION, COVER ASSY -

FWD SHROUD

NA NA NA NA 5/21/21 Parts list only

19.1 71A45558P1 ASTM B162 NA SHEET, NICKEL

Hamilton Precision Metals, Lancaster, PA, cage = 66729

3/26/21

Hamilton is owed by Ametek Inc. (5ESP2) in 2007. Charlene Putt, 717-569-7061.

Need to call them. ILS has one source per B162. Alex got verification that they make per ASTM B162. He is sending them 71A45558 to make sure. Ametek does not make this foil in this thin thicknesses any longer. 4/16/21. However, Hamilton appears to make this sheet to our spec., but cold rolled only. 5/21/21.

19.1 ALT 200828091

Nickel 200 (UNS N02200), Nickle 201 (UNS N02201) per

ASTM B162

1420-01-566-3781 AF Mgt

SHEET, NICKEL

Hamilton Precision Metals, Lancaster, PA, cage = 66729 All Foils Inc., 16100 industrial Parkway, Strongville, OH, 800- 521-0054, cage = 4U465

All Foils / cage 4U465 Mike Kulik, 800-521-0054, mkulik@allfoils.com 3/26/21

All Foils Inc. is an active company. Need to call them. ILS has one source per B162. I called and talked to Mike Kulik and he thought they could supply the foil. I sent him the 200828091 spec. 4/12/21. I called and left a message for Mike. 4/16/21, 5/14/21. Emailed Mike. 5/17/21. Left Vmail 5/27/21. Left message and email.

6/2/21. All Foils can make the nickel 200/ 201 per our spec. They can not perform the Total Hemispherical Emittance testing in house. However, a Lab that can is listed in our spec. I assume we are good to go. 7/7/21.