EDR.pdf
PDF 110 KB Posted
- Attached to
- CABLE ASSEMBLY, SPECI Federal contract opportunity
- Solicitation number
- SPRHA2-22-Q-0705
- Issued by
- Defense Logistics Agency Aviation
About this file
This document provides engineering data requirements and specifications for a cable assembly procurement by the Defense Logistics Agency Aviation. Key details include: the cable assembly will consist of three components with part numbers 23007767G1, 23007766G1, and 23007765G1. The solicitation number is SPRHA2-22-Q-0705 and seeks 17 each of national stock number 1190-01-438-7179. This is a 100% small business set aside and the first article may be required. Technical data can be found at the provided SAM.gov link. Production units must pass testing for capacitance within a specified range when connected as described. Connectors are available from ITT Cannon and its supplier Meridian Marketing located in Aurora, Colorado.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| SPRHA222Q0705_______0005.pdf | ||
| SPRHA222Q0705_______0004.pdf | ||
| SPRHA222Q0705_______0003.pdf | ||
| QA.pdf | ||
| SPRHA222Q0705_______0002.pdf | ||
| SPRHA222Q0705_______0001.pdf | ||
| A002_CPP.pdf | ||
| A001_FA.pdf | ||
| SOW.pdf | ||
| SPRHA222Q0705.pdf | ||
| EDL.pdf |
Show all 11
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
REV:
ENGINEERING DATA REQUIREMENTS
(ATTACHMENT “A”)
NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.
1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:
CABLE ASSEMBLY,SPEC; MK21
2. PART NUMBER:
23007768G1
3. NATIONAL STOCK NUMBER:
1190-01-438-7179NP
PREPARED BY:
DOUGLAS ESKELSEN
OFFICE SYMBOL:
414 SCMS/GUEA
DATE:
28 JULY, 2021
HILL AFB FORM 462 Page 1 of 1
4. CONTACT 414TH EN FOR AN INTERVIEW WITH THE CONTRACTOR POST AWARD/PRE-PROCEED NOTICE.
THIS CABLE ASSEMBLY CONSISTS OF THE FOLLOWING:
23007767G1 CABLE ASSY TEST MOD
23007766G1 MODULE CALIBRATION
23007765G1 CABLE ASSEMBLY GROUND
5. THE 47A528238P1 CONNECTOR WAS ADDED TO DRAWING 23007766G1 PER EO-01C0422 REPLACING 47A528239P1 BECAUSE THE ORIGINAL LOCKHEED MARTIN DRAWING WAS IN ERROR. THE OTHER CONNECTOR 47A528239P4 IS ON 23007767G1.
6. PRODUCTION UNITS REQUIRE TESTING, AS DESCRIBED BELOW.
Equipment Required:
Capacitance Meter (CM20A or CR50 or Equivalent accuracy and resolution specification)
1) Inspect connector for bent pins, reject cable if pins are:
a. Bent aside greater than a diameter
b. Missing, protruding, or recessed connector pins
c. Rips, tears in insulation/sleeving
d. Ensure all connectors are clean
2) Connect P1 of W41164 to P2 of shunt cap
3) Zero capacitance meter on lowest range
NOTE: In next steps be sure to use capacitance connectors. Non-compliance will result in incorrect readings!
4) Connect the red plug of cable W41164 to the positive (+) jack of the capacitance meter
5) Connect the black plug of cable W41164 to the negative (-) jack of the capacitance meter
6) Connect the green plug of cable W41164 to the black plug of W41164
7) Turn capacitance meter to range that gives no less than 0.00 nF resolution (more resolution [zeros] is better)
8) Record reading
9) Disconnect shunt cap
10) Record reading
11) Subtract reading in step 10 from reading in step 8; result must be 1.80 to 2.40 nF
12) Reconnect shunt cap and store cable
7. THE CONNECTORS ARE AVAILABLE FROM ITT CANNON AND ITS SUPPLIER MERIDIAN MARKETING AURORA CO (303) 790-7171.
File details come from the government source that posted it. Updated .