EDR.pdf

REV: ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

MATRIX ASSY, WING STORES STA 3/7 F-16

2. PART NUMBER:

16E2504-723

3. NATIONAL STOCK NUMBER:

6110-01-592-3015WF

PREPARED BY:

JUSTIN ALLRED

OFFICE SYMBOL:

416 SCMS/GUEAA

DATE:

20191212

HILL AFB FORM 462 Page 1 of 2

4.0 THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC., WILL BE USED IN LIEU OF THE DATA INDICATED. THE SUPERSEDED

DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.

4.1 THE SOURCES/MATERIALS IF LISTED ON THE SPECIFICATION, STANDARDS AND DRAWINGS ARE THE ONLY SOURCES/MATERIALS FOR THOSE ITEMS. ANY SUBSTITUTIONS SHALL HAVE PRIOR APPROVAL BY THE COGNIZANT

ENGINEERING ACTIVITY.

5. MARK AND IDENTIFY PER MIL-STD-130 IN LIEU OF MIL-STD-130.

6. PAGE 7, PARAGRAPH 3.2.3.2 OF 16PR145, REVISION "G" DOES NOT APPLY.

7. USE 16PR106 IN CONJUNCTION WITH 16PR145 FOR MANUFACTURE OF THIS ITEM. SECTION 1, PAGE 1-2, PARAGRAPH 3, NOTE 2 OF 16PR145 DOES NOT APPLY.

8. THIS IS AN AIRCRAFT PART. USE THE APPROPRIATE PORTION OF MIL-STD-2000 THAT APPLIES AIRCRAFT SOLDERING FOR ALL SOLDERING REQUIREMENTS.*NOTE: J-STD-001 MAYBE USED IN LIEU OF MIL-STD-

2000, IF SPEC MEETS OR EXCEEDS MIL-STD-2000

9. DEVIATIONS FROM SPECIFICATIONS IDENTIFIED IN CONTROL DRAWINGS ARE NOT AUTHORIZED WITHOUT

PRIOR APPROVAL BY THE COGNIZANT ENGINEERING ACTIVITY.

10. 16PR106 IS FURNISHED, BRAID PER 16PR106 (IF APPLICABLE).

11. 16PR145, REVISION “G”, PAGE 7, PARAGRAPH 3.2.3.2 REFERRING TO THE USE OF WHITE TUBING, DOES NOT APPLY TO THE MANUFACTURE OF THIS ITEM. FOR HARNESS BRAID, USE 1200 WEIGHT GREEN THREAD WHEN STOCK OF 200 WEIGHT THREAD IS

EXHAUSTED.

12. THE SOURCE FOR ANTI-SABOTAGE LACQUER (MATERIAL 114-136305) IF REQUIRED IS AVAILABLE FROM:

ORANGE PRODUCTS COMPANY

CAGE 01195

PH: 214-438-7321

UNDER THE NAME "TORQUE SEAL (F-900), COLOR RED.

13. AN ADDITIONAL SOURCE FOR SOME OF THE SUB COMPONENTS IS:

EXCEL INTERNATIONAL

PH: 805-446-1740

http://www.silcom.com/excel

14. EFFECTIVE 9 MAY 2005 THE DEPARTMENT OF THE AIR FORCE ISSUED AN AIR WORTHINESS ADVISORY (M-05-01)

REGARDING THE USE OF LEAD-FREE SOLDER IN ELECTRICAL AND ELECTRONIC MILITARY PRODUCTS. TO DATE, NO LEAD- FREE SOLDER FORMULATION HAS MATCHED THE RELIABILITY AND PERFORMANCE QUALITIES OF THE STANDARD LEADED SOLDERS. THEREFORE, UNTIL SUCH TIME AS A SUITABLE, RELIABLE LEAD-FREE SOLDER REPLACEMENT IS IDENTIFIED, ALL ELECTRONIC EQUIPMENT SUPPLIERS SHALL CONTINUE TO PROVIDE THE DEPARTMENT OF THE AIR FORCE WITH ITEMS WHICH MEET ALL PERFORMANCE, COMPATIBILITY, AND RELIABILITY STANDARDS PREVIOUSLY ESTABLISHED WITH LEADED SOLDERS. FAILURE TO DO SO, COULD ADVERSELY IMPACT THE PERFORMANCE AND RELIABILITY OF WEAPON SYSTEMS

AFFECTING NATIONAL SECURITY.

REV: ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

MATRIX ASSY, WING STORES STA 3/7 F-16

2. PART NUMBER:

16E2504-723

3. NATIONAL STOCK NUMBER:

6110-01-592-3015WF

PREPARED BY:

JUSTIN ALLRED

OFFICE SYMBOL:

416 SCMS/GUEAA

DATE:

20191212

HILL AFB FORM 462 Page 2 of 2

15. THE USE OF LEAD-FREE SOLDER OR LEAD-FREE PLATED COMPONENTS IN MILITARY ELECTRONIC PRODUCTS IS CONSIDERED A FLIGHT SAFETY AND NATIONAL SECURITY CONCERN. FOR THIS REASON THE US AIR FORCE WANTS TO BE NOTIFIED WHEN LEAD-FREE COMPONENTS AND MANUFACTURING PROCESSES HAVE BEEN IMPLEMENTED. AS PART OF SATISFACTORY COMPLIANCE WITH THE REQUIREMENTS OF THIS CONTRACT THE US AIR FORCE REQUIRES NOTIFICATION

ON A NO-COST BASIS WHEN ANY OF THE FOLLOWING CONDITIONS EXIST:

1. COMMERCIAL OFF-THE-SHELF (COTS) OR ANY OTHER ELECTRICAL COMPONENTS THAT CONTAIN LEAD-FREE SOLDER

OR LEAD-FREE PLATED COMPONENTS ARE USED IN THE END-ITEM.

2. ANY LEAD-FREE COMPONENT OR PART USED TO MANUFACTURE THE END ITEM THAT IS NOT IDENTIFIED WITH A

SEPARATE PART NUMBER OR DESIGNATION.

16. IF NO LEAD-FREE, LEAD-FREE PLATED COTS OR ANY OTHER LEAD-FREE ELECTRICAL OR ELECTRONICS COMPONENTS EXIST

IN THE MANUFACTURED END-ITEM, THE CONTRACTOR SHALL PROVIDE WRITTEN CERTIFICATION OF COMPLIANCE AS A

DELIVERABLE WITH THE CONTRACT.

1. USE INDUSTRY STANDARD IPC-1066, "MARKING, SYMBOLS AND LABELS FOR IDENTIFICATION OF LEAD-FREE AND

OTHER REPORTABLE MATERIALS IN LEAD-FREE ASSEMBLIES, COMPONENTS AND DEVICES,"

2. INCLUDE THE PROGRAM ENGINEER'S EVALUATION OF THE PURCHASING/REPAIR ITEM FOR ANY "LEAD-FREE" MILITARY PART(S) IN REFERENCE TO ITS' RELIABILITY, PERFORMANCE AND COMPATIBILITY FOR THE SYSTEM.

17. POC FOR THIS MATTER IS THE ENGINEERING SUPPORT ACTIVITY (ESA).

18. TOLERANCES FOR BREAKOUT LENGTHS OF MORE THAN SIX (6) INCHES SHALL BE -00.0 INCHES +0.5 INCHES.

19. UNIQUE IDENTIFICATION (UID) SHALL BE APPLIED PER MIL-STD-130 IN LIEU OF FPS-3008:

A. MINIMUM 1/8TH INCH ON HUMAN READABLE TO INCLUDE:

1. CAGE (17V)

2. P/N (1P)

3. SERIAL NUMBER (1S)

B. MINIMUM 1/4 INCH SQUARE ON MACHINE READABLE 2D MATRIX – CONSTRUCT 2 – TO

INCLUDE:

1. CAGE (17V)

2. P/N (1P)

3. SERIAL NUMBER (1S)

C. LABEL SHALL CONTAIN ALL DATA ON EXISTING LABEL, IF EXISTING LABEL IS TO BE

REPLACED.

D. SAME LABEL MATERIAL SHALL BE USED AS SPECIFIED IN DRAWING FOR EXISTING

LABEL.

E. MIL-STD-130, ANSI/AIM BCII, ISO 15434, ISO 15415, AND ISO 15418.