C08.0 N4523A23Q1319 HPAC Solicitation.pdf

SEE ADDENDUM

(No Collect Calls)

N4523A23Q1319 17-May-2023

b. TELEPHONE NUMBER

(360)552-1651

8. OFFER DUE DATE/LOCAL TIME

10:00 AM 25 May 2023

5. SOLICITATION NUMBER 6. SOLICITATION ISSUE DATE

AUTHORIZED FOR LOCAL REPRODUCTION

PREVIOUS EDITION IS NOT USABLE

STANDARD FORM 1449 (REV. 2/2012)

Prescribed by GSA – FAR (48 CFR) 53.212

(TYPE OR PRINT)

(SIGNATURE OF CONTRACTING OFFICER)

ADDENDA ARE

26. TOTAL AWARD AMOUNT (For Gov t. Use Only )

23.

CODE 10. THIS ACQUISITION IS

SUCH ADDRESS IN OFFER

17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT

BELOW IS CHECKED

TELEPHONE NO.

N4523A9. ISSUED BY

18b. SUBMIT INVOICES TO ADDRESS SHOWN IN BLOCK 18a. UNLESS BLOCK

7. FOR SOLICITATION

INFORMATION CALL:

a. NAME

EMMA J CRAIGHEAD

2. CONTRACT NO. 3. AWARD/EFFECTIVE DATE 4. ORDER NUMBER

(TYPE OR PRINT)

30b. NAME AND TITLE OF SIGNER 30c. DATE SIGNED 31b. NAME OF CONTRACTING OFFICER

30a. SIGNATURE OF OFFEROR/CONTRACTOR 31a.UNITED STATES OF AMERICA

0 27a. SOLICITATION INCORPORATES BY REFERENCE FAR 52.212-1. 52.212-4. FAR 52.212-3. 52.212-5 ARE ATTACHED.

25. ACCOUNTING AND APPROPRIATION DATA

1. REQUISITION NUMBER

20.

ADDITIONAL SHEETS SUBJECT TO THE TERMS AND CONDITIONS SPECIFIED.

OFFEROR TO COMPLETE BLOCKS 12, 17, 23, 24, AND 30

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS

ARE NOT ATTACHED

27b. CONTRACT/PURCHASE ORDER INCORPORATES BY REFERENCE FAR 52.212-4. FAR 52.212-5 IS ATTACHED. ADDENDA ARE ARE NOT ATTACHED

(BLOCK 5), INCLUDING ANY ADDITIONS OR CHANGES WHICH ARE

SET FORTH HEREIN, IS ACCEPTED AS TO ITEMS:

. YOUR OFFER ON SOLICITATION

28. CONTRACTOR IS REQUIRED TO SIGN THIS DOCUMENT AND RETURN

% FOR:SET ASIDE:UNRESTRICTED OR X

SMALL BUSINESSX

17a.CONTRACTOR/ CODE FACILITY

OFFEROR CODE

N4523A PSNS&IMF

C440

COMMAND SERVICES CONTRACTING SUPPORT

1400 FARRAGUT AVENUE

BREMERTON WA 98314-2026

18a. PAYMENT WILL BE MADE BY CODE

RATED ORDER UNDER

DPAS (15 CFR 700)

13a. THIS CONTRACT IS A

13b. RATING

CODE15. DELIVER TO CODE N4523A 16. ADMINISTERED BY

12. DISCOUNT TERMS11. DELIVERY FOR FOB DESTINA-

TION UNLESS BLOCK IS

MARKED

SEE SCHEDULE

14. METHOD OF SOLICITATION

RFQ IFB RFPX

PUGET SOUND NAVAL SHIPYARD DET SAN DIEGO

NICHOLAS ROLLINSON

NAVAL BASE POINT LOMA, 140 SYLVESTER RD.

SAN DIEGO CA 92106

TEL: FAX:

FAX:

TEL: SERVICE-DISABLED

VETERAN-OWNED

SMALL BUSINESS

8(A)

HUBZONE SMALL

BUSINESS

SIZE STANDARD:

NAICS:

X

OFFER DATED

29. AWARD OF CONTRACT: REF.

DELIVER ALL ITEMS SET FORTH OR OTHERWISE IDENTIFIED ABOVE AND ON ANY

COPIES TO ISSUING OFFICE. CONTRACTOR AGREES TO FURNISH AND

EMAIL:

TEL:

31c. DATE SIGNED

SEE SCHEDULE

SCHEDULE OF SUPPLIES/ SERVICESITEM NO. QUANTITY UNIT UNIT PRICE AMOUNT

24.22.21.19.

WOMEN-OWNED SMALL BUSINESS (WOSB)

ELIGIBLE UNDER THE WOMEN-OWNED

SMALL BUSINESS PROGRAM

EDWOSB

32g. E-MAIL OF AUTHORIZED GOVERNMENT REPRESENTATIVE

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS

(CONTINUED)

PAGE 2 OF22

ACCEPTED, AND CONFORMS TO THE CONTRACT, EXCEPT AS NOTED: ______________________________________________________

32a. QUANTITY IN COLUMN 21 HAS BEEN

RECEIVED INSPECTED

32b. SIGNATURE OF AUTHORIZED GOVERNMENT

REPRESENTATIVE

32c. DATE 32d. PRINTED NAME AND TITLE OF AUTHORIZED GOVERNMENT

REPRESENTATIVE

32e. MAILING ADDRESS OF AUTHORIZED GOVERNMENT REPRESENTATIVE 32f . TELEPHONE NUMBER OF AUTHORIZED GOVERNMENT REPRESENTATIVE

37. CHECK NUMBER

FINALPARTIALCOMPLETE

36. PAYMENT35. AMOUNT VERIFIED

CORRECT FOR

34. VOUCHER NUMBER

FINAL

33. SHIP NUMBER

PARTIAL

38. S/R ACCOUNT NUMBER 39. S/R VOUCHER NUMBER 40. PAID BY

41a. I CERTIFY THIS ACCOUNT IS CORRECT AND PROPER FOR PAYMENT

41b. SIGNATURE AND TITLE OF CERTIFYING OFFICER 41c. DATE

42a. RECEIVED BY (Print)

42b. RECEIVED AT (Location)

42c. DATE REC'D (YY/MM/DD) 42d. TOTAL CONTAINERS

STANDARD FORM 1449 (REV. 2/2012) BACK

Prescribed by GSA – FAR (48 CFR) 53.212

AUTHORIZED FOR LOCAL REPRODUCTION

PREVIOUS EDITION IS NOT USABLE

SEE SCHEDULE

20.

SCHEDULE OF SUPPLIES/ SERVICES

21.

QUANTITY UNIT

22. 23.

UNIT PRICE

24.

AMOUNT

19.

ITEM NO.

Section SF 1449 - CONTINUATION SHEET

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

CLIN

Number

Lease two (2) HPACs

FFP

Lease two (2) High Pressure Air Compressors in accordance with the standards and specifications provided in the Performance Work Statement (PWS).

FOB: Destination

NET AMT

INSPECTION AND ACCEPTANCE TERMS

Supplies/services will be inspected/accepted at:

CLIN INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY

0001 N/A Government Destination Government

DELIVERY INFORMATION

CLIN DELIVERY DATE QUANTITY SHIP TO ADDRESS DODAAC /

CAGE

0001 05-JUL-2023 PUGET SOUND NAVAL SHIPYARD DET

SAN DIEGO

NICHOLAS ROLLINSON

NAVAL BASE POINT LOMA, 140

SYLVESTER RD.

SAN DIEGO CA 92106

FOB: Destination

N4523A

PWS

PERFORMANCE WORK STATEMENT

(PWS)

Two High Pressure Air Compressors (HPACs)

PART 1

GENERAL INFORMATION

1. GENERAL: This is a non-personal services contract to provide temporary high pressure air compressors (HPACs). The Government shall not exercise any supervision or control over the contract service providers performing the services herein. Such contract service providers shall be accountable solely to the Contractor who, in turn is responsible to the Government.

1.1 Description of Services/Introduction: The contractor shall deliver, provide technical support for assembly, operation, maintenance and urgent repairs, and return the compressor and accessory equipment as described in this specification. The government will assemble, test, operate, maintain, repair (if necessary), dis-assemble and re- package the HPAC system as required.

1.2 Background: In support of maintenance being conducted on a 688 class submarine during the project availability, PSNS & IMF requires two (2) each stand-alone high pressure compressed air systems for use supplying ship service air system and industrial applications including breathing air.

1.3 Objectives: To provide 2 ea. high pressure air compressors for supplying ship service air system and industrial applications including breathing air.

1.4 Scope: The compressed air systems shall be a stand-alone, turnkey system capable of unattended operation and provide startup assistance, operator training and all maintenance except for: oil checks, draining the condensate tank, and changing the desiccant cartridges (if used).

1.5 Period of Performance (POP): See Contract Line Item Numbers (CLINs) section for specified POPs.

1.6 Quality Control (QC):

1.6.1 Quality Assurance: The government shall evaluate the contractor’s performance under this contract in accordance with the Quality Assurance Surveillance Plan (QASP). This plan is primarily focused on what the Government must do to ensure that the contractor has performed in accordance with the performance standards. It defines how the performance standards will be applied, the frequency of surveillance, and the minimum acceptable defect rate(s).

1.7 Place of Performance: Point Loma Naval Base, San Diego, CA.

1.7.1 Hours of Operation: The contractor is responsible for conducting business during normal business hours or as specified by the COR, Monday thru Friday except Federal holidays or when the Government facility is closed due to local or national emergencies, administrative closings, or similar Government directed facility closings. The contractor is also responsible for providing emergency technical support 24 hours/day, 7 days/week, during the duration of the POP. For other than firm fixed price contracts, the contractor will not be reimbursed when the government facility is closed for the above reasons. The Contractor must at all times maintain an adequate workforce for the uninterrupted performance of all tasks defined within this PWS when the Government facility is not closed for the above reasons. When hiring personnel, the Contractor shall keep in mind that the stability and continuity of the workforce are essential.

1.7.2 Recognized Holidays: Contractor is not required to perform services on federal holidays. The list of current federal holidays can be found here: https://www.opm.gov/policy-data-oversight/pay-leave/federal- holidays/

1.8 Security Requirements:

1.8.1 Contractors who have a need to access a government computer system may be eligible for a contractor CAC; most contractors are not eligible for a CAC. Contact the Contracting Officer’s Representative (COR) or Contracting Officer’s Security Officer for assistance as needed. Access verification is required for all personnel requesting entry into the Enclave via the turnstile for pedestrians or vehicle gates for government and authorized commercial/contract vehicles.

1.8.2 In order to use Enclave entry control points, Armed Forces and Department of Defense (DoD) personnel desiring access to the piers require an encoded Armed Forces Identification Common Access Card (CAC) for Active Duty Military Personnel, DoD CAC for civilian personnel, a DBIDS badge for contractor personnel, or a temporary access badge issued by the Pass and ID office. The process for enrollment into the database is discussed in the following paragraphs. Access to NBPL’s Enclave does not grant individuals access to other installation Enclave areas.

1.8.3 Only Government vehicles (GOVs), golf carts, or licensed commercial vehicles making deliveries are authorized entry into the Enclave. Afloat tenant commands and ashore commands that perform support functions for the afloat units will be authorized Enclave access in government vehicles. At no time will parking be allowed on the piers; as vehicle access is granted for loading and unloading of personnel and/or equipment. Any commands or contractors in violation of parking on the piers will be forwarded to the NBPL Commanding Officer and are subject to the loss of vehicle access privileges into the Enclave. Commands and contractors will be required to request permission from the NBPL Commanding Officer (CO) for privilege reinstatement.

1.8.4 GOVs, golf carts, and approved licensed commercial vehicles, are the only vehicles allowed access inside the Enclave. Private Motor Vehicles (PMVs) and rental vehicles are not authorized access to the Enclave area. Only GOVs and golf carts assigned to units operating within the Enclave will be authorized to park in designated parking spaces overnight. GOVs and golf carts must be parked in a designated parking space within the Enclave, but not on the pier. For security concerns, ships deploying, or getting underway, for one week or longer, will be required to park their vehicles outside of the Enclave.

1.8.5 All contractors requiring access to the Enclave will contact their government sponsor for entry approval.

After confirming the legitimate requirement for that specific contractor to have vehicular access to the Enclave, the Force Protection Department will grant permission and then provide the contractor access. All licensed commercial vehicles entering the Enclave are subject to vehicle inspection prior to entry.

1.8.6 Normal hours of operation for vehicular access is 24/7.

1.8.7 CAC holders may escort personnel into the Enclave area under the following conditions:

1.8.8 The guest(s) will enter/exit through the main Enclave entrance, Post 14. The sponsor shall remain physically present with the personnel they are escorting at all times. The limit to the number of personnel a single sponsor may escort is ten (10). However, if the sponsor cannot maintain physical control of all sponsored personnel, then additional escort personnel are required. In the instance visitors/guests should require access outside of normal working hours, access shall be granted through the COG, upon verification of necessity. The sponsor will escort the guest(s) from time of entry to the time of exit of the Enclave area. Upon completion of the visit, the sponsor shall escort the guest(s) to the main Enclave entrance and verify the guest(s) have left the restricted area.

1.8.9 This access/authorization is not inherited by or extended to contractors. Contractors may not act as sponsors for individuals or groups.

1.8.10 Escorted personnel over the age of 16, in the restricted area, must have a current state or federally-issued identification.

1.8.11 To reiterate access controls for the Enclave area, NBPL Enclave is a restricted area requiring enrolled access. The Enclave fence line and turnstiles are monitored and recorded by a digitalized date/time stamped camera system. Additionally, the turnstiles report each access made with a date/time stamp and name of encoded card utilized for entry to the Enclave. Allowing access for anyone other than who the CAC/DBIDS Card is issued to is in violation of a lawful order and is subject to suspension of encoded card privileges. This includes swiping cards for others “piggybacking” to allow multiple entries under one access.

1.8.12 For Vehicle Access, contractors shall provide a valid, current Driver's License, vehicle registration, and proof of insurance to Naval Base Point Loma Pass & ID Office.

1.8.13 Cell phones equipped with cameras are PROHIBITED in the Waterfront Restricted Areas.

1.8.14 Contractor Employees shall adhere to PSNS&IMF NOTICE 5239.6 PORTABLE ELECTRONIC

DEVICE (PED) GUIDANCE.

1.8.15 ALL portable electronic devices are STRICTLY PROHIBITED onboard submarines (e.g. phones, mp3 devices, computing devices, recording equipment, removable storage media, etc.).

1.9 Post Award Conference/Periodic Progress Meetings: The Contractor agrees to attend any post award conference convened by the contracting activity or contract administration office in accordance with Federal Acquisition Regulation Subpart 42.5. The contracting officer, Contracting Officers Representative (COR), and other Government personnel, as appropriate, may meet periodically with the contractor to review the contractor's performance. At these meetings the contracting officer will apprise the contractor of how the government views the contractor's performance and the contractor will apprise the Government of problems, if any, being experienced. Appropriate action shall be taken to resolve outstanding issues. These meetings shall be at no additional cost to the government.

1.10 Contracting Officer Representative (COR): The (COR) will be identified by separate letter. The COR monitors all technical aspects of the contract and assists in contract administration The COR is authorized to perform the following functions: assure that the Contractor performs the technical requirements of the contract: perform inspections necessary in connection with contract performance: maintain written and oral communications with the Contractor concerning technical aspects of the contract: issue written interpretations of technical requirements, including Government drawings, designs, specifications: monitor Contractor's performance and notifies both the Contracting Officer and Contractor of any deficiencies;

coordinate availability of government furnished property, and provide site entry of Contractor personnel. A letter of designation issued to the COR, a copy of which is sent to the Contractor, states the responsibilities and limitations of the COR, especially with regard to changes in cost or price, estimates or changes in delivery dates. The COR is not authorized to change any of the terms and conditions of the resulting order.

1.11 Organizational Conflict of Interest: Contractor and subcontractor personnel performing work under this contract may receive, have access to or participate in the development of proprietary or source selection information (e.g., cost or pricing information, budget information or analyses, specifications or work statements, etc.) or perform evaluation services which may create a current or subsequent Organizational Conflict of Interests (OCI) as defined in FAR Subpart 9.5. The Contractor shall notify the Contracting Officer immediately whenever it becomes aware that such access or participation may result in any actual or potential OCI and shall promptly submit a plan to the Contracting Officer to avoid or mitigate any such OCI. The Contractor’s mitigation plan will be determined to be acceptable solely at the discretion of the Contracting Officer and in the event the Contracting Officer unilaterally determines that any such OCI cannot be satisfactorily avoided or mitigated, the Contracting Officer may affect other remedies as he or she deems necessary, including prohibiting the Contractor from participation in subsequent contracted requirements which may be affected by the OCI.

PART 2

DEFINITIONS & ACRONYMS

2. DEFINITIONS & ACRONYMS

2.1 DEFINITIONS: COMMON DEFINITIONS: Per Clause 52.212-4(e), clause 52.202-1 is incorporated by reference to this contract.

2.1.1 CONTRACTOR. A supplier or vendor awarded a contract to provide specific supplies or service to the government. The term used in this contract refers to the prime.

2.1.2 CONTRACTING OFFICER. A person with authority to enter into, administer, and or terminate contracts, and make related determinations and findings on behalf of the government. Note: The only individual who can legally bind the government.

2.1.3 CONTRACTING OFFICER'S REPRESENTATIVE (COR). An employee of the U.S. Government appointed by the contracting officer to administer the contract. Such appointment shall be in writing and shall state the scope of authority and limitations. This individual has authority to provide technical direction to the Contractor as long as that direction is within the scope of the contract, does not constitute a change, and has no funding implications. This individual does NOT have authority to change the terms and conditions of the contract.

2.1.4 QUALITY ASSURANCE SURVEILLANCE PLAN (QASP). An organized written document specifying the surveillance methodology to be used for surveillance of contractor performance.

2.1.5 QUALITY CONTROL. All necessary measures taken by the Contractor to assure that the quality of an end product or service shall meet contract requirements.

2.2. ACRONYMS:

COR Contracting Officer Representative DOD Department of Defense FAR Federal Acquisition Regulation KO Contracting Officer OCI Organizational Conflict of Interest PWS Performance Work Statement QA Quality Assurance QASP Quality Assurance Surveillance Plan QC Quality Control

PART 3

GOVERNMENT FURNISHED PROPERTY, EQUIPMENT, AND SERVICES

3. GOVERNMENT FURNISHED ITEMS AND SERVICES: NONE

PART 4

CONTRACTOR FURNISHED ITEMS AND SERVICES

4. CONTRACTOR FURNISHED ITEMS AND RESPONSIBILITIES:

4.1 General: Deliver and pick up 2 each temporary high pressure air compressors at Point Loma Naval Station, San Diego Ca. The Contractor shall furnish all supplies, equipment, facilities and services required to perform work under this contract that are not listed under Section 3 of this PWS.

PART 5

SPECIFIC TASKS

5. TECHNICAL REQUIREMENTS

5.1 Compressed air supply parameters.

5.1.1 Each compressor shall supply at least 85 SCFM of air at the discharge of the dryer at a pressure of 4950 psig and a maximum temperature of 110ºF.

5.1.2 The compressed air supplied by the compressed air systems shall be certified for breathing air quality per reference 6.1 or the applicable OSHA regulations for compressed breathing air supply. The air quality specifications for breathing air and ship service are as follows.

5.1.2.1 Oxygen: 19.5% to 23.5%.

5.1.2.2 Carbon Dioxide (by volume): 1000 ppm maximum.

5.1.2.3 Carbon Monoxide (by volume): 10 ppm maximum.

5.1.2.4 Hydrocarbons (condensed): 0.005 milligrams/liter maximum.

5.1.2.5 No noticeable odor, when judged by the government.

5.1.2.6 Supply temperature: 115º F maximum.

5.1.2.7 Water content: Not to exceed a dew point of (-70º F) at atmospheric pressure (18 ppm by volume).

5.1.2.8 Compressed air oil content shall not exceed 0.1 ppm by weight.

5.1.2.9 Dirt/particulate: Not to exceed 5 microns nominal and 18 microns absolute.

5.2 Equipment Requirements.

5.2.1 Compressed air system shall be:

5.2.2 Suitable for operation in an outdoor, marine, seashore environment set in place upon a flat grade without foundation anchors.

5.2.3 Electrically powered 460-VAC, 3-phase, 60 Hz power supply. The compressed air systems shall be self-contained so that the systems are capable of producing breathable quality, compressed air without any additional utilities such as a water supply, low-pressure air, or 120VAC power, and without any customer supplied filters, dryers, or catalytic beds.

5.2.4 Self-regulating with fully automatic controls, alarms, and indicators so that the compressor package requires monitoring by compressor operators no more than once every 72 hours (3 days) after start-up, except a daily oil check may be required.

5.2.5 Deliver compressors with sufficient cartridges to permit cartridge change-outs.

5.2.6 If a regenerating desiccant-type dryer is used, the dryer shall automatically swap towers and regenerate. The desiccant shall have fewer than ten hours service upon delivery and shall include an after-filter rated 1 micron or smaller.

5.2.7 An after-cooler with an automatic water drain trap to remove condensed moisture from the compressed air. The after-cooler shall cool the compressed air to within 15ºF of the ambient temperature at the rated capacity of the compressor at pressures between 3000 and 5000 psig.

5.2.8 The control panel shall be listed by Underwriter’s Laboratory or other nationally recognized Testing

Laboratory for use in the weather and shall have a NRTL marking present on the control panel.

5.2.9 The compressed air systems shall be entirely contained on skid and shall be constructed to be portable and capable of being transported by both forklift and crane.

5.2.10 The total dimensions of each installed compressed air system, including the compressor and all accessory equipment, shall not exceed 8-foot- wide, by 20-foot long by 10-foot high.

5.2.11 The compressed air systems shall be in accordance with Reference 6.3.

5.2.12 The compressor condensate discharge shall be equipped with a flexible hose eight feet in length, to permit users the option of directing condensate into a user-supplied 55-gallon drum.

5.2.13 The Compressed air system setup shall be 100% complete within 24 hours of delivery.

5.2.14 Operate the compressed air systems and supply air meeting the specified dew point and oil content for one continuous hour.

5.2.15 Relief valves shall bear tags indicating the set point and test date. The valve protecting the receiver shall be an ASME relief valve and shall have intact wire seal(s).

5.2.16 Relief valve isolation valves shall be installed in accordance with Reference 6.3, and meet the following requirements.

5.2.17 The isolation valve(s) shall be locked open by a strap which will be broken if the valve is closed.

5.2.18 When an isolation valve is closed, isolating the receiver from the relief valve, the valve shall also isolate the receiver from the compressor.

5.2.19 Final discharge pressure shall be displayed on a calibrated pressure gauge.

5.2.20 Have a pressure gauge and the associated pressure switches, which start and stop the compressor and shall be in calibration and have labels confirming the calibration due date.

5.3 Equipped with the following accessory equipment:

5.3.1 An ASME stamped receiver.

5.3.2 The compressor control shall include the following connections for customer use. These connections shall be labeled as “optional customer switches” in the control schematic in the operator’s manual.

5.3.3 Remote Shutdown – for use with a customer-supplied carbon monoxide alarm.

5.3.4 Run Indication – supplies 120VAC power to a customer supplied solenoid valve, but only while the compressor is running. When the compressor is not running, the run indication terminals shall not be energized.

5.3.5 A low oil-pressure switch.

5.3.6 A silencer on the blow-down air exhaust.

5.3.7 An automatic blow-down system.

5.3.8 A filtration/purification system as required for the output.

5.3.9 NAVSEA approved oil-removal filter installed between the compressor and dryer. This requirement also applies to oil-less compressors.

5.3.10 The compressor shall have a tag that is attached to the front of compressor indicating the most recent change date and the signature of the person who made the change.

5.3.11 The filter shall be one of the following CUNO Incorporated, Micro-Klean III U78B2 filter element.

The recommended CUNO filter housing is CUNO Model 40344-10. Downstream of the CUNO filter housing, a separate housing shall contain activated carbon to remove odors. A particulate filter incorporated in the activated carbon cartridge or a separate filter immediately downstream of the activated carbon cartridge shall be provided to prevent the migration of activated carbon particles into the airstream.

Replacement filter elements and activated carbon shall be supplied by the contractor and replaced by the customer. Contractor shall get with onsite Government representative to determine quantity amount and how often these replacement filters should be changed.

5.3.12 Two in parallel purification systems that consists of the following:

5.3.12.1 An L-Factor FC-530550-SB, sintered bronze, 20 micron, 90% efficient filter element rated for

78 SCFM, in an L-Factor model P3C housing.

5.3.12.2 A molecular sieve cartridge.

5.3.12.3 A combination element which includes activated carbon, catalyst, and a particulate filter. An air dryer system to ensure the output compressed air meets the required water content specification.

The dryer shall be a cartridge-type unit or an automatically regenerating desiccant tower system.

Each air dryer system included with the compressed air systems shall serve only a single compressor.

5.3.12.4 If a cartridge-type dryer is used, each airflow path through the dryer shall include at least two dryer cartridges in series. Replacement cartridges shall be supplied by the contractor and installed by the customer. The installed dryer capacity shall be sufficient to permit operation of the compressor for 72 hours at rated capacity.

5.3.13 Include drop a pan or Drip tray to capture or contain any fluid leaks. Then pan or tray shall be sized to hold 110% of the total volume of fluids contained in the compressor.

5.3.14 The operating manual shall include a requirement that the isolation valve shall remain open while the receiver is pressurized above 15 psi.

5.4 Contractor shall:

5.4.1 Conduct an initial receipt inspection with the onsite Government representative to document current condition of the compressed air system.

5.4.2 Coordinate with the onsite Government representative for the initial delivery of two compressed air systems, and for pick-up, upon notification at the end of the period of performance (POP).

5.4.3 Maintain close liaison and good communication with the Government representative throughout duration of Contract.

5.4.4 Provide 24 hour a day / seven days a week on-call repair service technician. The Contractor shall be responsible for being onsite and initiating repairs within 24-hours of verbal or written notification that the equipment has malfunctioned.

5.4.5 In the event that either compressed air systems fails to operate, within 6-hours of initial notification the

Contractor shall supply a manufacturer’s repair/service technician to determine whether the compressed air system is repairable or shall be replaced with fully operational compressed air system. Repairs or replacements of the compressed air systems to restore to 100% operation of the equipment in question within 24 hours after a determination have been made to repair or replace the unit.

5.4.6 No later than 48-hours after initial notification and the determination has been made to repair or replace the unit, all repairs or replacement of the compressed air system shall be complete and unit shall be in 100% fully-operational condition.

5.5 Markings.

5.5.1 Provide a 10-inch by 10-inch sign containing the Company, including name and phone number contact information of the service/repair technician representative, affixed to the exterior of the enclosure door for any malfunction issues associated with the compressed air system(s.)

5.5.2 The compressed air systems shall have the (1) air capacity, (2) maximum supply pressure, and (3) the electric horsepower and RPM rating stamped on a metal plate attached to the equipment.

5.5.3 Each major component of the systems, including the compressor, electric motor and the purification system shall have the manufacturer's name and the manufacturer's serial number stamped on a metal plate attached to the component.

5.5.4 No metal stamping is permitted on any surface subjected to high stresses in service and shall be in compliance of reference 6.2 and 6.3.The compressed air systems shall have a current certificate of inspection attached to each pressure vessel in the compressed air systems, indicating inspection by a state approved pressure vessel inspector.

5.6 Additional Services/Requirements.

5.6.1 Contractor Shall.

5.6.1.1 Conduct start/stop, and familiarization of operation training for the compressor air system, onsite at Naval Base Point Loma, with Government employees, as mutually coordinated between the Contractor and onsite Government representative.

5.6.2 Conduct a half-hour retest of the equipment, after repairs or replacement, to verify satisfactory operation.

5.6.3 Provide the pressure vessel certificate to the onsite Government representatives upon delivery. Pressure vessel certificate shall be from a state certified pressure vessel inspector.

5.6.4 Provide a manufacturers operating instruction manuals for the air compressors, and all other major components associated with the compressed air systems to the onsite Government representative.

5.6.5 The manufactures operating instructions manual shall include a parts list, operating parameters for all gauges and indicators & blank log sheets.

5.6.6 Coordinate with onsite Government representative for the specific date and time of compressor air systems delivery, a minimum twenty-four (24) hours prior to delivery.

N4523A23Q1319

PART 6

APPLICABLE

PUBLICATIONS

6. APPLICABLE PUBLICATIONS

6.1. OPNAVINST 5100.23G - NAVY SAFETY AND OCCUPATIONAL HEALTH PROGRAM MANUAL

6.2. 42 USC 4907 – LABELING

6.3. ASME BOILER AND PRESSURE VESSEL CODE NON-MANDATORY APPENDIX M

CLAUSES INCORPORATED BY REFERENCE

52.203-12 Limitation On Payments To Influence Certain Federal

Transactions

JUN 2020

52.204-7 System for Award Management OCT 2018 52.204-13 System for Award Management Maintenance OCT 2018 52.204-16 Commercial and Government Entity Code Reporting AUG 2020 52.204-16 Commercial and Government Entity Code Reporting AUG 2020 52.212-1 Instructions to Offerors--Commercial Products and

Commercial Services

MAR 2023

52.212-3 Offeror Representations and Certifications--Commercial Products and Commercial Services

DEC 2022

52.212-4 Contract Terms and Conditions--Commercial Products and Commercial Services

DEC 2022

52.232-39 Unenforceability of Unauthorized Obligations JUN 2013 52.252-6 Authorized Deviations In Clauses NOV 2020 252.203-7000 Requirements Relating to Compensation of Former DoD

Officials

SEP 2011

252.203-7002 Requirement to Inform Employees of Whistleblower Rights DEC 2022 252.203-7005 Representation Relating to Compensation of Former DoD

Officials

SEP 2022

252.204-7003 Control Of Government Personnel Work Product APR 1992 252.204-7008 Compliance With Safeguarding Covered Defense Information

Controls

OCT 2016

252.204-7009 Limitations on the Use or Disclosure of Third-Party Contractor Reported Cyber Incident Information

JAN 2023

252.204-7012 Safeguarding Covered Defense Information and Cyber Incident Reporting

JAN 2023

252.204-7015 Notice of Authorized Disclosure of Information for Litigation Support

JAN 2023

252.204-7016 Covered Defense Telecommunications Equipment or Services -- Representation

DEC 2019

252.204-7017 Prohibition on the Acquisition of Covered Defense Telecommunications Equipment or Services -- Representation

MAY 2021

252.204-7018 Prohibition on the Acquisition of Covered Defense Telecommunications Equipment or Services

JAN 2023

252.204-7019 Notice of NIST SP 800-171 DoD Assessment Requirements MAR 2022 252.204-7020 NIST SP 800-171 DoD Assessment Requirements JAN 2023 252.204-7024 Notice on the Use of the Supplier Performance Risk System MAR 2023

252.215-7013 Supplies and Services Provided by Nontraditional Defense Contractors

JAN 2023

252.223-7008 Prohibition of Hexavalent Chromium JAN 2023 252.225-7012 Preference For Certain Domestic Commodities APR 2022 252.225-7048 Export-Controlled Items JUN 2013 252.232-7003 Electronic Submission of Payment Requests and Receiving

Reports

DEC 2018

252.232-7010 Levies on Contract Payments DEC 2006 252.237-7010 Prohibition on Interrogation of Detainees by Contractor

Personnel

JAN 2023

252.244-7000 Subcontracts for Commercial Products or Commercial Services

JAN 2023

CLAUSES INCORPORATED BY FULL TEXT

52.212-2 EVALUATION--COMMERCIAL PRODUCTS AND COMMERCIAL SERVICES (NOV 2021)

(a) The Government will award a contract resulting from this solicitation to the responsible offeror whose offer conforming to the solicitation will be most advantageous to the Government, price and other factors considered. The following factors shall be used to evaluate offers:

i. Technical Capability

ii. Past Performance

iii. Price

(b) Reserved

(c) A written notice of award or acceptance of an offer, mailed or otherwise furnished to the successful offeror within the time for acceptance specified in the offer, shall result in a binding contract without further action by either party. Before the offer's specified expiration time, the Government may accept an offer (or part of an offer), whether or not there are negotiations after its receipt, unless a written notice of withdrawal is received before award.

(End of provision)

52.212-5 CONTRACT TERMS AND CONDITIONS REQUIRED TO IMPLEMENT STATUTES OR

EXECUTIVE ORDERS--COMMERCIAL PRODUCTS AND COMMERCIAL SERVICES (MAR 2023)

(a) The Contractor shall comply with the following Federal Acquisition Regulation (FAR) clauses, which are incorporated in this contract by reference, to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services:

(1) 52.203-19, Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements (JAN 2017) (section 743 of Division E, Title VII, of the Consolidated and Further Continuing Appropriations Act, 2015 (Pub. L.

113-235) and its successor provisions in subsequent appropriations acts (and as extended in continuing resolutions)).

(2) 52.204-23, Prohibition on Contracting for Hardware, Software, and Services Developed or Provided by Kaspersky Lab and Other Covered Entities (NOV 2021) (Section 1634 of Pub. L. 115-91).

(3) 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment. (NOV 2021) (Section 889(a)(1)(A) of Pub. L. 115-232).

(4) 52.209-10, Prohibition on Contracting with Inverted Domestic Corporations (NOV 2015).

(5) 52.232-40, Providing Accelerated Payments to Small Business Subcontractors (MAR 2023) (31 U.S.C. 3903 and 10 U.S.C. 3801).

(6) 52.233-3, Protest After Award (AUG 1996) (31 U.S.C. 3553).

(7) 52.233-4, Applicable Law for Breach of Contract Claim (OCT 2004) (Public Laws 108-77 and 108-78 (19 U.S.C. 3805 note)).

(b) The Contractor shall comply with the FAR clauses in this paragraph (b) that the Contracting Officer has indicated as being incorporated in this contract by reference to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services: [Contracting Officer check as appropriate.]

___ (1) 52.203-6, Restrictions on Subcontractor Sales to the Government (JUN 2020), with Alternate I (NOV 2021) (41 U.S.C. 4704 and 10 U.S.C. 4655).

___ (2) 52.203-13, Contractor Code of Business Ethics and Conduct (NOV 2021) (41 U.S.C. 3509).

___ (3) 52.203-15, Whistleblower Protections under the American Recovery and Reinvestment Act of 2009 (JUN 2010) (Section 1553 of Pub. L. 111-5). (Applies to contracts funded by the American Recovery and Reinvestment Act of 2009.)

XXX (4) 52.204-10, Reporting Executive Compensation and First-Tier Subcontract Awards (JUN 2020) (Pub. L.

109-282) (31 U.S.C. 6101 note).

___ (5) [Reserved]

___ (6) 52.204-14, Service Contract Reporting Requirements (OCT 2016) (Pub. L. 111-117, section 743 of Div.

C).

___ (7) 52.204-15, Service Contract Reporting Requirements for Indefinite-Delivery Contracts (OCT 2016) (Pub.

L. 111-117, section 743 of Div. C).

XXX (8) 52.209-6, Protecting the Government's Interest When Subcontracting with Contractors Debarred, Suspended, or Proposed for Debarment. (NOV 2021) (31 U.S.C. 6101 note).

___ (9) 52.209-9, Updates of Publicly Available Information Regarding Responsibility Matters (OCT 2018) (41 U.S.C. 2313).

____ (10) [Reserved]

____ (11) 52.219-3, Notice of HUBZone Set-Aside or Sole-Source Award (OCT 2022) (15 U.S.C. 657a).

____ (12) 52.219-4, Notice of Price Evaluation Preference for HUBZone Small Business Concerns (OCT 2022) (if the offeror elects to waive the preference, it shall so indicate in its offer) (15 U.S.C. 657a).

____ (13) [Reserved]

XXX (14)(i) 52.219-6, Notice of Total Small Business Set-Aside (NOV 2020) (15 U.S.C. 644).

____ (ii) Alternate I (MAR 2020) of 52.219-6.

____ (15)(i) 52.219-7, Notice of Partial Small Business Set-Aside (NOV 2020) (15 U.S.C. 644).

____ (ii) Alternate I (MAR 2020) of 52.219-7.

____ (16) 52.219-8, Utilization of Small Business Concerns (OCT 2022) (15 U.S.C. 637(d)(2) and (3)).

____ (17)(i) 52.219-9, Small Business Subcontracting Plan (OCT 2022) (15 U.S.C. 637(d)(4)).

____ (ii) Alternate I (NOV 2016) of 52.219-9.

____ (iii) Alternate II (NOV 2016) of 52.219-9.

____ (iv) Alternate III (JUN 2020) of 52.219-9.

____ (v) Alternate IV (SEP 2021) of 52.219-9.

____ (18) (i) 52.219-13, Notice of Set-Aside of Orders (MAR 2020) (15 U.S.C. 644(r)).

XXX (ii) Alternate I (MAR 2020) of 52.219-13.

____ (19) 52.219-14, Limitations on Subcontracting (OCT 2022) (15 U.S.C. 657s).

____ (20) 52.219-16, Liquidated Damages—Subcontracting Plan (SEP 2021) (15 U.S.C. 637(d)(4)(F)(i)).

____ (21) 52.219-27, Notice of Service-Disabled Veteran-Owned Small Business Set-Aside (OCT 2022) (15 U.S.C.

657f).

XXX (22) (i) 52.219-28, Post-Award Small Business Program Rerepresentation (MAR 2023) (15 U.S.C. 632(a)(2)).

____ (ii) Alternate I (MAR 2020) of 52.219-28.

____ (23) 52.219-29, Notice of Set-Aside for, or Sole-Source Award to, Economically Disadvantaged Women- Owned Small Business Concerns (OCT 2022) (15 U.S.C. 637(m)).

____ (24) 52.219-30, Notice of Set-Aside for, or Sole-Source Award to, Women-Owned Small Business Concerns Eligible Under the Women-Owned Small Business Program (OCT 2022) (15 U.S.C. 637(m)).

____ (25) 52.219-32, Orders Issued Directly Under Small Business Reserves (MAR 2020) (15 U.S.C. 644(r)).

____ (26) 52.219-33, Nonmanufacturer Rule (SEP 2021) (15 U.S.C. 657s).

XXX (27) 52.222-3, Convict Labor (JUN 2003) (E.O. 11755).

XXX (28) 52.222-19, Child Labor--Cooperation with Authorities and Remedies (DEC 2022) (E.O. 13126).

XXX (29) 52.222-21, Prohibition of Segregated Facilities (APR 2015).

ADDENDUM TO 52.222-41 Department of Labor Wage Determination 2015-5635 Rev. 21 Dated 27 Dec 2022 incorporated into this award is available at https://sam.gov

XXX (30)(i) 52.222-26, Equal Opportunity (SEP 2016) (E.O. 11246).

____ (ii) Alternate I (FEB 1999) of 52.222-26.

XXX (31)(i) 52.222-35, Equal Opportunity for Veterans (JUN 2020) (38 U.S.C. 4212).

____ (ii) Alternate I (JUL 2014) of 52.222-35.

XXX (32)(i) 52.222-36, Equal Opportunity for Workers with Disabilities (JUN 2020) (29 U.S.C. 793).

____ (ii) Alternate I (JUL 2014) of 52.222-36.

____ (33) 52.222-37, Employment Reports on Veterans (JUN 2020) (38 U.S.C. 4212).

____ (34) 52.222-40, Notification of Employee Rights Under the National Labor Relations Act (DEC 2010) (E.O.

13496).

XXX (35)(i) 52.222-50, Combating Trafficking in Persons (NOV 2021) (22 U.S.C. chapter 78 and E.O. 13627).

____ (ii) Alternate I (MAR 2015) of 52.222-50 (22 U.S.C. chapter 78 and E.O. 13627).

____ (36) 52.222-54, Employment Eligibility Verification (MAY 2022). (E. O. 12989). (Not applicable to the acquisition of commercially available off-the-shelf items or certain other types of commercial products or commercial services as prescribed in FAR 22.1803.)

____ (37)(i) 52.223-9, Estimate of Percentage of Recovered Material Content for EPA–Designated Items (MAY 2008) (42 U.S.C. 6962(c)(3)(A)(ii)). (Not applicable to the acquisition of commercially available off-the-shelf items.)

____ (ii) Alternate I (MAY 2008) of 52.223-9 (42 U.S.C. 6962(i)(2)(C)). (Not applicable to the acquisition of commercially available off-the-shelf items.)

____ (38) 52.223-11, Ozone-Depleting Substances and High Global Warming Potential Hydrofluorocarbons (JUN 2016) (E.O. 13693).

____ (39) 52.223-12, Maintenance, Service, Repair, or Disposal of Refrigeration Equipment and Air Conditioners

(JUN 2016) (E.O. 13693).

____ (40)(i) 52.223-13, Acquisition of EPEAT® Registered Imaging Equipment (JUN 2014) (E.O.s 13423 and 13514).

____ (ii) Alternate I (OCT 2015) of 52.223-13.

____ (41)(i) 52.223-14, Acquisition of EPEAT® Registered Televisions (JUN 2014) (E.O.s 13423 and 13514).

____ (ii) Alternate I (JUN 2014) of 52.223-14.

____ (42) 52.223-15, Energy Efficiency in Energy-Consuming Products (MAY 2020) (42 U.S.C. 8259b).

____ (43)(i) 52.223-16, Acquisition of EPEAT®-Registered Personal Computer Products (OCT 2015) (E.O.s 13423 and 13514).

____ (ii) Alternate I (JUN 2014) of 52.223-16.

XXX (44) 52.223-18, Encouraging Contractor Policies to Ban Text Messaging While Driving (JUN 2020) (E.O.

13513).

____ (45) 52.223-20, Aerosols (JUN 2016) (E.O. 13693).

____ (46) 52.223-21, Foams (JUN 2016) (E.O. 13693).

____ (47)(i) 52.224-3, Privacy Training (JAN 2017) (5 U.S.C. 552a).

____ (ii) Alternate I (JAN 2017) of 52.224-3.

XXX (48) (i) 52.225-1, Buy American--Supplies (OCT 2022) (41 U.S.C. chapter 83).

XXX (ii) Alternate I (OCT 2022) of 52.225-1.

____ (49)(i) 52.225-3, Buy American-Free Trade Agreements-Israeli Trade Act (DEC 2022) (19 U.S.C. 3301 note, 19 U.S.C. 2112 note, 19 U.S.C. 3805 note, 19 U.S.C. 4001 note, 19 U.S.C. chapter 29 (sections 4501-4732), Public Law 103-182, 108-77, 108-78, 108-286, 108-302, 109-53, 109-169, 109-283, 110-138, 112-41, 112-42, and 112-43.

____ (ii) Alternate I [Reserved].

____ (iii) Alternate II (DEC 2022) of 52.225-3.

____ (iv) Alternate III (JAN 2021) of 52.225-3.

XXX (v) Alternate IV (OCT 2022) of 52.225-3.

____ (50) 52.225-5, Trade Agreements (DEC 2022) 19 U.S.C. 2501, et seq., 19 U.S.C. 3301 note).

XXX (51) 52.225-13, Restrictions on Certain Foreign Purchases (FEB 2021) (E.O.'s, proclamations, and statutes administered by the Office of Foreign Assets Control of the Department of the Treasury).

____ (52) 52.225-26, Contractors Performing Private Security Functions Outside the United States (OCT 2016) (Section 862, as amended, of the National Defense Authorization Act for Fiscal Year 2008; 10 U.S.C. Subtitle A, Part V, Subpart G Note).

____ (53) 52.226-4, Notice of Disaster or Emergency Area Set-Aside (NOV 2007) (42 U.S.C. 5150

____ (54) 52.226-5, Restrictions on Subcontracting Outside Disaster or Emergency Area (NOV 2007) (42 U.S.C.

5150).

____ (55) 52.229-12, Tax on Certain Foreign Procurements (FEB 2021).

____ (56) 52.232-29, Terms for Financing of Purchases of Commercial Products and Commercial Services (NOV 2021) (41 U.S.C. 4505, 10 U.S.C. 3805).

____ (57) 52.232-30, Installment Payments for Commercial Products and Commercial Services (NOV 2021) (41 U.S.C. 4505, 10 U.S.C. 3805).

XXX (58) 52.232-33, Payment by Electronic Funds Transfer—System for Award Management (OCT 2018) (31 U.S.C. 3332).

XXX (59) 52.232-34, Payment by Electronic Funds Transfer—Other than System for Award Management (JUL 2013) (31 U.S.C. 3332).

____ (60) 52.232-36, Payment by Third Party (MAY 2014) (31 U.S.C. 3332).

____ (61) 52.239-1, Privacy or Security Safeguards (AUG 1996) (5 U.S.C. 552a).

____ (62) 52.242-5, Payments to Small Business Subcontractors (JAN 2017)(15 U.S.C. 637(d)(13)).

____ (63)(i) 52.247-64, Preference for Privately Owned U.S.-Flag Commercial Vessels (NOV 2021) (46 U.S.C.

55305 and 10 U.S.C. 2631).

____ (ii) Alternate I (APR 2003) of 52.247-64.

____ (iii) Alternate II (NOV 2021) of 52.247-64.

(c) The Contractor shall comply with the FAR clauses in this paragraph (c), applicable to commercial services, that the Contracting Officer has indicated as being incorporated in this contract by reference to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services: [Contracting Officer check as appropriate.]

XXX (1) 52.222-41, Service Contract Labor Standards (AUG 2018) (41 U.S.C. chapter 67).

XXX (2) 52.222-42, Statement of Equivalent Rates for Federal Hires (MAY 2014) (29 U.S.C. 206 and 41 U.S.C.

chapter 67).

_____ (3) 52.222-43, Fair Labor Standards Act and Service Contract Labor Standards--Price Adjustment (Multiple Year and Option Contracts) (AUG 2018) (29 U.S.C. 206 and 41 U.S.C. chapter 67).

_____ (4) 52.222-44, Fair Labor Standards Act and Service Contract Labor Standards--Price Adjustment (MAY 2014) (29 U.S.C 206 and 41 U.S.C. chapter 67).

_____ (5) 52.222-51, Exemption from Application of the Service Contract Labor Standards to Contracts for Maintenance, Calibration, or Repair of Certain Equipment--Requirements (MAY 2014) (41 U.S.C. chapter 67).

_____ (6) 52.222-53, Exemption from Application of the Service Contract Labor Standards to Contracts for Certain Services--Requirements (MAY 2014) (41 U.S.C. chapter 67).

_____ (7) 52.222-55, Minimum Wages for Contractor Workers Under Executive Order 14026 (JAN 2022) (E.O.

13658).

_____ (8) 52.222-62, Paid Sick Leave Under Executive Order 13706 (JAN 2022) (E.O. 13706).

_____ (9) 52.226-6, Promoting Excess Food Donation to Nonprofit Organizations (JUN 2020) (42 U.S.C. 1792).

(d) Comptroller General Examination of Record. The Contractor shall comply with the provisions of this paragraph

(d) if this contract was awarded using other than sealed bid, is in excess of the simplified acquisition threshold, as defined in FAR 2.101, on the date of award of this contract, and does not contain the clause at 52.215-2, Audit and Records--Negotiation.

(1) The Comptroller General of the United States, or an authorized representative of the Comptroller General, shall have access to and right to examine any of the Contractor's directly pertinent records involving transactions related to this contract.

(2) The Contractor shall make available at its offices at all reasonable times the records, materials, and other evidence for examination, audit, or reproduction, until 3 years after final payment under this contract or for any shorter period specified in FAR Subpart 4.7, Contractor Records Retention, of the other clauses of this contract. If this contract is completely or partially terminated, the records relating to the work terminated shall be made available for 3 years after any resulting final termination settlement. Records relating to appeals under the disputes clause or to litigation or the settlement of claims arising under or relating to this contract shall be made available until such appeals, litigation, or claims are finally resolved.

(3) As used in this clause, records include books, documents, accounting procedures and practices, and other data, regardless of type and regardless of form. This does not require the Contractor to create or maintain any record that the Contractor does not maintain in the ordinary course of business or pursuant to a provision of law.

(e) (1) Notwithstanding the requirements of the clauses in paragraphs (a), (b), (c), and (d) of this clause, the Contractor is not required to flow down any FAR clause, other than those in this paragraph (e)(1) in a subcontract for commercial products or commercial services. Unless otherwise indicated below, the extent of the flow down shall be as required by the clause—

(i) 52.203-13, Contractor Code of Business Ethics and Conduct (NOV 2021) (41 U.S.C. 3509).

(ii) 52.203-19, Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements (JAN 2017) (section 743 of Division E, Title VII, of the Consolidated and Further Continuing Appropriations Act, 2015 (Pub. L.

113-235) and its successor provisions in subsequent appropriations acts (and as extended in continuing resolutions)).

(iii) 52.204-23, Prohibition on Contracting for Hardware, Software, and Services Developed or Provided by Kaspersky Lab and Other Covered Entities (NOV 2021) (Section 1634 of Pub. L. 115-91).

(iv) 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment. (NOV 2021) (Section 889(a)(1)(A) of Pub. L. 115-232).

(v) 52.219-8, Utilization of Small Business Concerns (OCT 2022) (15 U.S.C. 637(d)(2) and (3)), in all subcontracts that offer further subcontracting opportunities. If the subcontract (except subcontracts to small business concerns) exceeds the applicable threshold specified in FAR 19.702(a) on the date of subcontract award, the subcontractor must include 52.219-8 in lower tier subcontracts that offer subcontracting opportunities.

(vi) 52.222-21, Prohibition of Segregated Facilities (APR 2015).

(vii) 52.222-26, Equal Opportunity (SEP 2016) (E.O. 11246).

(viii) 52.222-35, Equal Opportunity for Veterans (JUN 2020) (38 U.S.C. 4212).

(ix) 52.222-36, Equal Opportunity for Workers with Disabilities (JUN 2020) (29 U.S.C. 793).

(x) 52.222-37, Employment Reports on Veterans (JUN 2020) (38 U.S.C. 4212).

(xi) 52.222-40, Notification of Employee Rights Under the National Labor Relations Act (DEC 2010) (E.O. 13496).

Flow down required in accordance with paragraph (f) of FAR clause 52.222-40.

(xxii) 52.232-40, Providing Accelerated Payments to Small Business Subcontractors (MAR 2023) (31 U.S.C. 3903 and 10 U.S.C. 3801). Flow down required in accordance with paragraph (c) of 52.232-40.

(xiii) 52.222-41, Service Contract Labor Standards (AUG 2018), (41 U.S.C. chapter 67).

(xiii) _____ (A) 52.222-50, Combating Trafficking in Persons (NOV 2021) (22 U.S.C. chapter 78 and E.O. 13627).

_____ (B) Alternate I (March 2, 2015) of 52.222-50 (22 U.S.C. chapter 78 and E.O. 13627).

(xiv) 52.222-51, Exemption from Application of the Service Contract Labor Standards to Contracts for Maintenance, Calibration, or Repair of Certain…