Attachment 1.pdf

CONTRACT

PRINTED 03/29/2021 ATTACHMENT PAGE

8305 1GA

C DESCRIPTION/SPECIFICATIONS

C.1 Plastic Sheeting 40’ x 100’ C.2 Reinforced three ply construction consisting of one sheet of vinyl on top, a polyester or nylon base fabric in the center and a sheet of vinyl on the bottom. The vinyl sheets are to be laminated to the polyester/nylon fabric. The polyester/nylon base fabric shall have an 8 x 5 count construction or comparable for material reinforcement. Fabric must be supple, easy to cut.

C.3 Color frosty clear/translucent white (will allow light to pass through) C.4 Size 40 FT X 100 FT C.5 Fire Retardency Manufactured to meet requirements of NFPA 701 Test Method 1 (large scale test) and material shall be marked SELF EXTINGUISHING C.6 Material must be capable of bonding when using an adhesive equivalent to 847 S/G from 3M (used for bonding vinyl plastics, nitrile rubbers, leather and metal to themselves and other materials) C.7 Vinyl shall meet following requirements:

a. Average thickness .014 (Test Method ASTM D-1777 L/R)

b. Nominal weight 7.0 oz/sq.yd (Test Method ASTM D-3776 L/R)

c. Yarns per inch average Warp of 9, Fill of 5 (Test Method ASTM D-3775 L/R)

d. Minimum Tensile strength (average), 1 strip 60 lbs longitudinal and 45 lbs transverse (Test method ASTM D751 L/R, Procedure B)

e. Minimum Tear Strength (average) - 30 lbs longitudinal and 30 lbs transverse (Test method ASTM D1004 L/R)

f. Minimum Hydrostatic Resistance 200 psi average (Test method ASTM D751 L/R, Procedure B)

g. Minimum Puncture Resistance (average) 130 lbs (Test method ASTM D751 L/R)

h. Low Temperature Bend Test - pass at -30°F (Test method ASTM D2136 L/R)

i. Linear Dimensional Change (Shrinkage) Test - <3% at 180-200°F (Test method ASTM D1204 L/R) C.8 ITEM 0002: CERTIFICATION/DATA REPORT. CERTIFICATION OF COMPLETION, SEE EXHIBIT A, SEQ A001.

TECHNICAL CONTENT IS REQUIRED TO MEET C.7

D PRESERVATION/PACKAGING/PACKING

D.1 D4 PREPARATION FOR DELIVERY (COMMERCIALLY PACKAGED ITEMS). Pack each roll in commercial box. Palletize all boxes. Boxes should not overhang pallets or exceed 54" in height.

D.2 IN ADDITION TO ABOVE REQUIREMENTS, The vendor shall package material by rolling the material around a 3" carboard tube.

D.3 Folding requirement-in width direction (40'), fold edges to the center to a finished width of approximately 30", then roll in length (100') direction onto 3" core. Do not fold in 100' direction before rolling onto core.

E INSPECTION ACCEPTANCE

E.1 E1 RESPONSIBILITY FOR INSPECTION

ITEM NO.

STOCK NUMBER

8305-LL-DM1-0058

SPECIAL CHARACTERISTICS

SIZE:40 FT. X 100 FT.

7 OZ. PER SQ. YD.

**SEE SECTION C. FOR DESCRIPTION/SPECIFICATIONS

ITEM NAME PLASTIC FILM SHEETING, TRANSLUCENT, FROSTED WHITE

SECTION B

SMIC

8L

1286E500

1/3

CONTRACT

PRINTED 03/29/2021 ATTACHMENT PAGE

8305 1GA

H SPECIAL PROVISIONS

K Section

L Section

M Section

1286E500

1 2/3

8305 1GA EXHIBIT A

SYSTEM/ITEM SHEETING PLASTIC

ITEM NO

CATEGORY

CONTRACTOR

CONTRACT

PAGE

(ADP DD FORM 1423(MECHANIZED EQUIVALENT) PER DAR CLAUSE 16-815)

PRINTED 03/29/2021

CONTRACT DATA REQUIREMENTS LIST

01 SEQ NO A001

02 DATA DESC

03 SUBTITLE CERTIFICATION OF COMPLETION

04 DID NUMBER

05 CONTRACT REF SECTION C.8

06 TECH OFFICE 244.2Q

07 DD 250 REQ DD

08 APP CODE

10 FREQUENCY 1-TIME

11 AS OF DATE

12 DATE 1ST SUBM W/MATERIAL

13 DATE SUB SUBM

14 DISTRIBUTION

15 TOTAL

16 REMARKS 1. TECHNICAL CONTENT IS REQUIRED TO MEET CONTRACT C.7

SEQ. NO. A001

PREPARED BY

APPROVED BY

DATE

DATE

DD FORM 1423

09 IAC INPUT

1286E500 3/3