Appendix A-DWG_201213463_Adapter.pdf

Exception to AF 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word 2010) 201213463.docx Computer Generated

APPLICATION REVISIONS

NEXT ASSY USED ON LTR DESCRIPTION DATE APPROVED

201213450-10 VDATS

201213462-10 VDATS

ALL SHEETS REV - VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT D. Distribution authorized to the Department of Defense and U.S. DoD contractors only (Critical Technology) (20 May 2008). Other requests shall be referred to AFLCMC/WNABA.

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.). or the Export Administration Act of 1979, as amended, Title 50, U.S.C., App. 2401 et seq. Violations of these export laws are subject to severe criminal penalties.

Disseminate in accordance with provisions of DoD Directive 5230.25.

DESTRUCTION NOTICE. Destroy by any method that will prevent disclosure of contents or reconstruction of the document.

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES

TOLERANCES ARE

DECIMALS ANGLES APPROVALS DATE

U.S. AIR FORCE

WR-ALC, ROBINS AFB, GA 31098

.XX ± ± DRAFTSMAN

T.C. Miller 01/24/14

TITLE

.XXX ± CHECKER

Foy Rearden 01/24/14

USB TO SERIAL ADAPTER

DO NOT SCALE DRAWING MATERIAL ENGINEER

THIRD ANGLE

PROJECTION

PROJECT ENGINEER

W. Larry Adams Jr. 01/24/14

PROJECT AUTHORITY

Kevin D. Simpson 01/24/14

SIZE

A

CAGE CODE

98752

DRAWING NO.

201213463

REV

RELEASE AUTHORITY

Harold Banks 01/24/14

SCALE

NONE

CAL.WT ACT.WT SHEET

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M, DIMENSIONING AND TOLERANCES.

ASME Y14.38, ABBREVIATIONS AND ACRONYMS.

MIL-STD-130M IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

2. THIS DRAWING ESTABLISHES THE REQUIREMENTS FOR A COMMERCIAL OFF THE SHELF

USB TO SERIAL ADAPTER .

3. IDENTIFICATION OF THE “SUGGESTED SOURCE(S) OF SUPPLY” HEREON IS NOT TO BE

CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A

SOURCE OF SUPPLY FOR THE ITEM(S).

4. QUALITY ASSURANCE. THE SUPPLIER SHALL VERIFY THAT UNITS SUPPLIED TO THIS

DRAWING CONFORM TO THE REQUIREMENTS SPECIFIED HEREIN.

5. VENDOR(S) SHALL MAKE NO CHANGE TO PRODUCT(S) SUPPLIED TO THE DRAWING

WHICH WOULD AFFECT INTERCHANGEABILITY OR DEGRADE EITHER PERFORMANCE OR

RELIABILITY OF THE PRODUCT WITHOUT PRIOR NOTICE

6. CONFIGURATION ITEM: DO NOT CHANGE WITHOUT SYSTEM ENGINEER APPROVAL.

CONFIGURATION FOR CONTROL NUMBER -001:

(IMAGE FOR REFERENCE ONLY)

CAGE: 98752 DWG. NO.: 201213463 REV – SHEET: 2

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201213463.docx Computer Generated

CONFIGURATION:

DIMENSIONS ARE IN INCHES

UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE NOMINAL

SPECIFICATIONS FOR CONTROL NUMBER -001:

ITEM USB TO SERIAL ADAPTER (A429; MIL-STD-1553)

MIL-STD-1553B:

NUMBER OF PORTS 4

NUMBER OF XMFR COUPLED PORTS 2 (A AND B CHANNELS)

NUMBER OF DIRECT CPLD PORTS 2 (A AND B CHANNELS)

MAX. DATA RATE 1 MHz

DATA WORD SIZE 20 BITS (16 BIT PAYLOAD)

IMPEDANCE 78 OHMS (TYPICAL)

VOLTAGE LEVELS (DIRECT CPLD) 1.4V TO 20 VPTP

VOLTAGE LEVELS (XMFR CPLD) 1.0V TO 10 VPTP

EMULATION MODES REMOTE TERMINAL (RT), BUS CONTROLLER (BC),

BUS MONITOR (MT)

NUMBER OF RT ADDRESSES

SIMULTANEOUSLY 31

ERROR CHECKING PER MIL-STD-1553B

ARINC 429 (A429)

NUMBER OF RECEIVER CHANNELS (RX) 4

NUMBER OF TRANSMIT CHANNELS (TX) 2

DATA WORD SIZE 32 BITS (24 BIT PAYLOAD)

MAX. DATA RATE 100 KHz

DATA RATE SELECTION HI DATA RATE / LOW DATA RATE

A429 DATA I/O CONNECTOR AND

MIL-STD-1553 ( DIRECT CPLD) I/O JACK

50 PIN D-SUB, J4 (A CONNECTOR PLUG / SHELL

IS INCLUDED)

NO. USB PORTS 2

INPUT POWER 6 VDC (PROVIDED BY 120VAC TO 6VDC ADAPTER)

TEMPERATURE RANGE 0 to 55 DEG. C

HUMIDITY RANGE 5% TO 95% (NON CONDENSING)

CAGE: 98752 DWG. NO.: 201213463 REV – SHEET: 3

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201213463.docx Computer Generated

CONFIGURATION FOR CONTROL NUMBER -002:

DIMENSIONS ARE IN INCHES (METERS)

UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE NOMINAL

(IMAGE FOR REFERENCE ONLY)

SPECIFICATIONS FOR CONTROL NUMBER -002:

DESCRIPTION ADPT MULTI-BLADE 6VDC 3.0A

TYPE SWITCHING

POWER (WATTS) 18 W

INPUT VOLTAGE 90 – 264 VAC

OUTPUT VOLTAGE 6 V (PER CONNECTOR)

OUTPUT CURRENT 3 A

CORD LENGTH 60 IN (1.53M) NOMINAL

LOAD REGULATION ±5%

DIMENSIONS (L x W x H) 2.91 x 1.71 x 1.39 in; (74 x 43.5 x 35.3 mm)

CONTROL

NUMBER

SUGGESTED SOURCE(S) OF SUPPLY

SUPPLIER DATA

CAGE

CODE

MANUFACTURER’S

PART NUMBER

MANUFACTURER’S

NAME AND ADDRESS

201213463-001 19645 BU67103U200L-JL0

DATA DEVICE CORPORATION

105 WILBUR PL.

BOHEMIA, NY. 11716

201213463-002 0P9A7 EMSA060300-P6P-SZ

CUI INC.

20050 SW 112TH AVE

TUALATIN, OR. 97062

CAGE: 98752 DWG. NO.: 201213463 REV – SHEET: 4

Exception to AF Form 1652 for CAD generation approved by HQ AFMC/ENP (MS Office/Word) 201213463.docx Computer Generated