Exhibit_6_FlagpoleCutSheet.pdf

Aluminum flash collar (Optional)

3000 PSI concrete

Dry sand tightly tamped after aligning pole

Plastic PVC Sono tube 24”

Project:

Location:

Architect:

Contractor Customer:

FLAGS.COM

1-800-858-8776 1395 NW 17th Ave #112B Delray Beach, FL 33445

Date:

Revision:

Job:

Model ECS 20

4"

Ground set tapered aluminum flagpole: ALLOY: 6063T6 Exposed height: 20'-0" Overall height: 22'-0" Ship in 1 section Butt diameter: 3-1/2" Top diameter: 2-3/8" Wall thickness: .125" Finish: 100 grit polish

One set of halyard, #8 polypropylene

One 9" Cast Aluminum Cleat

All shafts with overall length of more than 38'-6" are shipped in two sections.

Each section matched marked for field assembly.

Exposed portion of jam sleeve must be well lubricated prior to assembly.

1-1/2" maximum shop gap allowed for field fitting (ram for tight joint)

2 Nylon flag snaps

Crushed Stone

E xp os ed h ei gh t:

0'

-0

Ta pe re d po rti on

'-0

S tra ig ht p or tio n:

1' -0

O ve ra ll le ng th

'-0

C le at h ei gh t:

'-0

Fo un da tio n:

'-6

2' -0

16"

Stationary Truck Detail

Cast Aluminum body

3" - 14 gauge spun aluminum ball gold anodized

Single sheave truck, cast aluminum stationary, non-fouling type OT1 richardrpolanco Text Box Color: Bronze Anodized

Is su ed Ja nu ar y

Fl ag s.

co m

Ex te rn al

F la gp ol e In st ru ct io ns

Thank you for purchasing your flagpole from Flags.com. We would just like to remind you, for future reference, that we offer a complete line of flags and accessories. We look forward to helping you with all your flag and flagpole needs, after all we have been the flag and flagpole experts since 1990.

FOR YOUR RECORDS PLEASE WRITE DOWN YOUR

ORDER DETAILS BELOW SO WE CAN BETTER

SERVE YOU SHOULD ANY ISSUES ARISE OR IF YOU

NEED TO REPLACE A PART:

ORDER NUMBER: _____________

ORDER DATE: ___ /___ /___

FLAGPOLE MODEL: ____________

FLAGPOLE HEIGHT: ____________

Flags.com 1395 NW 17th Ave, Suite 112B

Delray Beach, FL 33445 800-858-8776 Fax 561-404-4954

Required Equipment 4-5 50 lb. bags of quick set concrete

Hand post hole digger

1 50 lb. bag of white dry sand

Shovel

1 50 lb bag of ¾ inch stone

Digging bar

1 tube of clear latex caulking

Rake

1 small tube lock tight

Pair of pliers

Screwdriver

Hammer

2 foot level

Wood wedges

Wrench

Saw Horse

Flags.com | 800-858-8776 | customerservice@flags.com 2

Directions

1. Dig foundation hole four to six times the butt diameter of the flagpole and 10% of the length of the pole. (See Diagram A)

2. Set the foundation tube so that the top of the foundation tube is two inches above grade. (See Diagram B)

3. Make sure the foundation tube is level and brace so that it will not move during the pouring of the concrete.

4. Pour concrete and trowel up even with top of foundation tube. Keep inside of foundation tube dry.

WARNING: Do not allow concrete to contact aluminum shaft.

5. Lay the flagpole on sturdy horses or blocks of wood, so the ground will not damage the finish of the shafts, and unwrap the pole. Fully grease sleeves. Align arrows and/or numbers on each section and push together. Numbers must be identical for a proper fit.

6. Screw the truck into the top of the pole, using a wrench to assure a tight fit. If cap-style truck is used, be sure set screws are well tightened.

7. Screw ball into truck and tighten ball set screw. Ball should be tightened into truck tightly by turning stem of ball with wrench. Do not tighten by turning ball with your hands.

8. If a flash collar is provided with pole, slide collar on from the bottom of pole to above cleat level and attach cleat with one screw to hold flash collar until after erection of pole. Then remove cleat, slide collar down, and replace cleat. Caulk between the collar and the pole with a waterproof sealant (like roofing cement or asphaltum sealant).

9. Thread rope through sheave (pulley) of truck and tie the ends together so that the rope will not drop out of the sheave during erection of the pole.

10. Erect pole into foundation tube and center it. Turn so that cleat holes are in the direction desired.

11. Place wood wedges between the pole and the foundation tube and level flagpole.

12. Pack dry sand between the pole and foundation tube. Leave two inches void at the top and fill with waterproof sealant to keep water out of sand.

13. Loop snaps on rope, space properly for flag(s) being used.

EXTREME CAUTION SHOULD BE EXERCISED WHEN INSTALLING FLAGPOLES NEAR OVERHEAD

POWER LINES, OR IN THE VICINITY OF BURIED CABLES

Flags.com | 800-858-8776 | customerservice@flags.com 3

Diagram A

Foundation Dimensions Exposed Height A B C D E

20’ 3’0” 6” 3’6” 30” 24” 25’ 3’0” 6” 3’6” 30” 24” 30’ 3’0” 6” 3’6” 30” 24” 35’ 3’6” 6” 4’0” 36” 30” 40’ 4’0” 6” 4’6” 42” 36” 45’ 4’6” 6” 5’0” 48” 42” 50’ 5’0” 8” 5’8” 48” 42” 60’ 6’0” 10” 6’10” 48” 42” 70’ 7’0” 12” 8’0” 60” 48” 80’ 9’0” 12” 9’0” 60” 48”

Flags.com | 800-858-8776 | customerservice@flags.com 4

Diagram B

Flags.com | 800-858-8776 | customerservice@flags.com 5

Foundation Dimensions